Search NASA⌕ Search

SEARCH · Search NASA

Results for “Thermal diffusivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

The Transport Properties of Quasi–One-Dimensional Ba 3 Co 2 O 6 (CO 3 ) 0.7

We have performed combined elastic neutron diffuse, electrical transport, specific heat, and thermal conductivity measurements on the quasi–one-dimensional Ba 3 Co 2 O 6 (CO 3 ) 0.7 single crystal to characterize its transport properties. A modulated superstructure of polyatomic CO 3 2- is formed, which not only interferes the electronic properties of this compound, but also reduces the thermal conductivity along the c-axis. Furthermore, a large magnetic entropy is observed to be contributed to the heat conduction. Our investigations reveal the influence of both structural and magnetic effects on its transport properties and suggest a theoretical improvement on the thermoelectric materials by building up superlattice with conducting ionic group.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Se diffusion in CdTe thin films for photovoltaics

Manipulating CdSeTe bandgrading to enhance photocurrent and carrier lifetime is an essential part of high-performance CdTe photovoltaics (PVs). Here, we examine Se diffusion kinetics in single-crystal and polycrystalline CdTe during deposition, thermal annealing, and CdCl 2 treatments. Se distributions are determined by dynamic secondary-ion-mass spectroscopy and Auger electron spectroscopy depth profiling and coupled with electron backscatter diffraction images of the crystalline structure. Effective bulk and grain boundary diffusion coefficients are determined by analytical models and discussed in the context of processing and film morphology. Se is found to diffuse in CdTe at much higher rates during CdCl 2 treatments than with thermal processing alone. GB diffusion also occurs at a significantly faster rate than bulk diffusion. As a result of these two effects, the near interface bulk and GB Se diffusion during CdCl 2 treatments dominates the bandgrading profiles in CdTe PVs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1987

Amorphous-Metal-Film Diffusion Barriers

Incorporation of N into Ni/W films reduces reactivity with Si substrate. Paper describes reactions between Si substrates and deposited amorphous Ni/W or Ni/N/W films. Thermal stability of amorphous Ni/W films as diffusion barriers in Si markedly improved by introduction of N into Ni/W films during deposition.

Nicolet, M. A.↗
NASA NTRS1985

Energy balance constraints on gravity wave induced eddy diffusion in the mesosphere and lower thermosphere

The constraints on turbulence improved by the mesospheric heat budget are reexamined, and the sufficiency of the theoretical evidence to support the hypothesis that the eddy Prandtl number is greater than one in the mesosphere is considered. The mesopause thermal structure is calculated with turbulent diffusion coefficients commonly used in chemical models and deduced from mean zonal wind deceleration. It is shown that extreme mesopause temperatures of less than 100 K are produced by the large net cooling. The results demonstrate the importance of the Prandtl number for mesospheric turbulence.

Strobel, D. F.↗
NASA NTRS1990

A highly durable injector faceplate design concept for O2/H2 propellants

Two different O2/H2 injector faceplate designs were used in a test bed rocket engine at the NASA Lewis Research Center facility. This test bed was operated in a pulsing mode to evaluate thrust chamber wall materials and coatings. Degradation of the sintered mesh injector face plates resulted in the substitution of a photoetched diffusion-bonded platelet faceplate. This faceplate accumulated over 4200 thermal cycles without damage or degradation. Prior testing for a total of 17,446 cycles required 19 sintered mesh faceplates. This average of 918 cycles per unit showed the diffusion bonded faceplate to have a thermal cycle capability ranging from 150 to 500 percent of that of the sintered wire unit. The test data also showed that the diffusion-bonded faceplate provided a more uniform flow of gaseous H2 through its discrete and uniformly spaced propellant orifices resulting in enhanced face cooling (no local hot spots) and increased performance. The injector faceplate designs are described and the results of the injector comparison test data are presented.

Mueggenburg, H. H.↗
DOE OSTI2014

Exploring atmospheres of hot mini-Neptune and extrasolar giant planets orbiting different stars with application to HD 97658b, WASP-12b, CoRoT-2b, XO-1b, and HD 189733b

We calculated an atmospheric grid for hot mini-Neptune and giant exoplanets that links astrophysical observable parameters—orbital distance and stellar type—with the chemical atmospheric species expected. The grid can be applied to current and future observations to characterize exoplanet atmospheres and serves as a reference to interpret atmospheric retrieval analysis results. To build the grid, we developed a one-dimensional code for calculating the atmospheric thermal structure and linked it to a photochemical model that includes disequilibrium chemistry (molecular diffusion, vertical mixing, and photochemistry). We compare the thermal profiles and atmospheric composition of planets at different semimajor axes (0.01 AU ≤ a ≤ 0.1 AU) orbiting F, G, K, and M stars. Temperature and UV flux affect chemical species in the atmosphere. We explore which effects are due to temperature and which are due to stellar characteristics, showing the species most affected in each case. CH{sub 4} and H{sub 2}O are the most sensitive to UV flux, H displaces H{sub 2} as the most abundant gas in the upper atmosphere for planets receiving a high UV flux. CH{sub 4} is more abundant for cooler planets. We explore vertical mixing, to inform degeneracies on our models and in the resulting spectral observables. For lower pressures, observable species like H{sub 2}O or CO{sub 2} can indicate the efficiency of vertical mixing, with larger mixing ratios for a stronger mixing. By establishing the grid, testing the sensitivity of the results, and comparing our model to published results, our paper provides a tool to estimate what observations could yield. We apply our model to WASP-12b, CoRoT-2b, XO-1b, HD189733b, and HD97658b.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2017

Development of Cost-Competitive Advanced Thermoelectric Generators for Direct Conversion of Vehicle Waste Heat into Useful Electrical Power

General Motors LLC (GM) proposed a project to develop a cost-effective thermoelectric generator (TEG) that is fully integrated into a GM production light-duty vehicle. The project goal was to reduce automotive energy consumption and CO 2 emissions by generating usable electricity from exhaust gas waste heat. The project objectives were to overcome the major obstacles to TEG commercialization and demonstrate 5% fuel economy improvement over the US06 drive cycle. We investigated electrical and thermal management strategies that included: (1) reducing electrical accessory load on the alternator using thermoelectric (TE) generated power; (2) shifting engine-driven accessories to electrical drive to raise the electrical accessory load consumption; (3) attempting to use the excess electrical power for something other than the vehicle electrical load e.g., propulsion (optimal for hybrids); and (4) implementing fast engine/transmission warm-up during cold-start. We developed a TEG system and all vehicle controls and electrical systems for full vehicle integration. The TEG system was modeled and analyzed for performance and cost. Heat exchangers and thermal interfaces between heat exchangers and TE modules were optimized for TE performance. Other objectives of the project were to (1) further optimize compositions and processing parameters for TE materials, (2) develop suitable diffusion barriers, interfaces electrical interconnections, and thermal contacts within TE modules, (3) implement adequate protection of TE materials and modules from degradation during operation, and (4) develop manufacturing and assembly processes for large scale production of TE materials and components that include scale-up plans for the production of 100,000 TEG units per year.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2015

Formation and coarsening of near-surface Ga nanoparticles on SiN{sub x}

We have investigated the formation and coarsening of near-surface Ga nanoparticles (NPs) in SiN{sub x} using Ga{sup +} focused-ion-beam-irradiation of SiN{sub x}, followed by rapid thermal annealing. For surfaces with minimal curvature, diffusive growth is apparent, leading to nearly close packed arrays with NP diameters as small as 3 nm and densities as high as ∼4 × 10{sup 12} cm{sup −2}. The diffusive flux increases with annealing temperature, leading to NP coarsening by Ostwald ripening. For surfaces with increased curvature, diffusion towards the valleys also increases during annealing, leading to Ga NP coalescence and a bi-modal distribution of NP sizes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

Adsorptive Separation and Sequestration of Krypton, I and C14 on Diamond Nanoparticles

The objective of this research proposal was to address the separation and sequestration of Kr and I from each other using nano-sized diamond particles and retaining these in diamond until they decay to the background level or can be used as a byproduct. Following removal of Kr and I, an adsorbent will be used to adsorb and store CO 2 from the CO 2 rich stream. A Field Enhanced Diffusion with Optical Activation (FEDOA-a large scale process that takes advantage of thermal, electrical, and optical activation to enhance the diffusion of an element into diamond structure) was used to load Kr and I on micron or nano sized particles having a larger relative surface area. The diamond particles can be further increased by doping it with boron followed by irradiation in a neutron flux. Previous studies showed that the hydrogen storage capacity could be increased significantly by using boron-doped irradiated diamond particles. Diamond powders were irradiated for a longer time by placing them in a quartz tube. The surface area was measured using a Quantachrome Autosorb system. No significant increase in the surface area was observed. Total surface area was about 1.7 m 2 /g. This suggests the existence of very minimal pores. Interestingly it showed hysteresis upon desorption. A reason for this may be strong interaction between the surface and the nitrogen molecules. Adsorption runs at higher temperatures did not show any adsorption of krypton on diamond. Use of a GC with HID detector to determine the adsorption capacity from the breakthrough curves was attempted, but experimental difficulties were encountered.

36 MATERIALS SCIENCE↗
NASA NTRS1993

Convective Effects During the Physical Vapor Transport Process. II - Thermosolutal Convection

The effect of an inert gas on the diffusive-convective physical vapor transport process is investigated for the case when the temperature gradient is stabilizing, and the concentration gradient destabilizing, for a wide parametric range. When an inert gas is present, the thermal and solutal convection oppose each other. The solutal field is destabilizing while the thermal field and the advective-diffusive flux stabilize the flow field. When the pressure of the inert component is increased, the stabilizing effect of the advective-diffusive flux is decreased; thus, convection becomes more vigorous. The nonlinear dynamics of the flow field here show a transition from quasi-periodic to chaotic state. When both stabilizing mechanisms are present, the flow field shows a transition to a steady state. Toward steady state, growth and amalgamation of rolls occur, which result in an overturning motion. This leads to a superposed flow consisting of one roll and a unidirectional flow. However, when the pressure is increased, the advective-diffusive stability mechanism is decreased. and oscillations of the flow field occur. The low gravity environment is effective at eliminating oscillatory behavior of the flow field and results in uniform temperature and concentration gradients.

Duval, Walter M. B.↗
NASA NTRS1994

Convection in the Physical Vapor Transport Process: Thermosolutal - Part 2

We consider the effect of an inert gas on the diffusive-convective physical vapor transport process. We investigate the case when the temperature gradient is stabilizing and the concentration gradient is destabilizing for a wide parametric range. When an inert gas is present, the thermal and solutal convection oppose each other. The solutal field is destabilizing while the thermal field and the advective-diffusive flux stabilize the flow field. When the pressure of the inert component is increased, the stabilizing effect of the advective-diffusive flux is decreased. The intensity of convection as well as the oscillatory transient time increases. Below, the critical Rayleigh number, the nonlinear dynamics of the flow field show an oscillatory approach to steady state. For parametric values in the neighborhood of the critical Rayleigh number, the flow field undergoes a chaotic transient which settles to a periodic state. The asymptotic state of the flow field shows that growth and amalgamation of cells yields an overturning motion which results in an asymmetric cellular structure. The low gravity environment yields the stabilizing advective-diffusive flow which results in uniform temperature and concentration gradients near the crystal interface.

Duval, Walter M. B.↗
DOE OSTI2012

Resonant charge-exchange involving excited helium atoms and reactive transport of local thermodynamic equilibrium helium plasma

The cross sections for charge-exchange and charge-transfer processes are evaluated for collisions of helium ions with parent-atoms in ground and excited states, with the principal quantum number n= 1-5, in the collision energy range from thermal up to 10 eV. Corresponding diffusion-type collision integrals are derived, and the role of 'abnormal' transport of electronically excited states on the reactive thermal conductivity of equilibrium helium plasma, at atmospheric pressure, estimated in the frame of a simplified approach.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2014

Hard X-ray emission and {sup 44}Ti line features of the Tycho supernova remnant

A deep hard X-ray survey of the International Gamma-Ray Astrophysics Laboratory (INTEGRAL) satellite has detected for the first time non-thermal emission up to 90 keV in the Tycho supernova (SN) remnant. Its 3-100 keV spectrum is fitted with a thermal bremsstrahlung of kT ∼ 0.81 ± 0.45 keV plus a power-law model of Γ ∼ 3.01 ± 0.16. Based on diffusive shock acceleration theory, this non-thermal emission, together with radio measurements, implies that the Tycho remnant may not accelerate protons up to >PeV but to hundreds TeV. Only heavier nuclei may be accelerated to the cosmic ray spectral 'knee'. In addition, using INTEGRAL, we search for soft gamma-ray lines at 67.9 and 78.4 keV that come from the decay of radioactive {sup 44}Ti in the Tycho remnant. A bump feature in the 60-90 keV energy band, potentially associated with the {sup 44}Ti line emission, is found with a marginal significance level of ∼2.6σ. The corresponding 3σ upper limit on the {sup 44}Ti line flux amounts to 1.5 × 10{sup –5} photon cm{sup –2} s{sup –1}. Implications on the progenitor of the Tycho SN, considered to be a Type Ia SN prototype, are discussed.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Modeling nanoparticle charge distribution in the afterglow of non-thermal plasmas and comparison with measurements

Particle charging in the afterglows of non-thermal plasmas typically take place in a non-neutral space charge environment. We model the same by incorporating particle-ion collision rate constant models, developed in prior work by analyzing particle-ion trajectories calculated using Langevin Dynamics simulations, into species transport equations for ions, electrons and charged particles in the afterglow. A scaling analysis of particle charging and additional Langevin Dynamics calculations of the particle-ion collision rate constant are presented to extend the range of applicability to ion electrostatic to thermal energy ratios of 300 and diffusive Knudsen number (that scales inversely with gas pressure) up to 2000. The developed collision rate constant models are first validated by comparing predictions of particle charge against measured values in a stationary, non-thermal DC plasma from past PK-4 campaigns published in Phys. Rev. Lett. 93(8): 085001 and Phys. Rev. E 72(1): 016406). The comparisons reveal excellent agreement within ±35% for particles of radius 0.6,1.0,1.3 μm in the gas pressure range of ~20-150 Pa. The experiments to probe particle charge distributions by Sharma et al. (J. Physics D: Appl. Phys. 53(24): 245204) are modeled using the validated particle-ion collision rate constant models and the calculated charge fractions are compared with measurements. The comparisons reveal that the ion/electron concentration and gas temperature in the afterglow critically influence the particle charge and the predictions are generally in qualitative agreement with the measurements. Along with critical assessment of the modeling assumptions, several recommendations are presented for future experimental design to probe charging in afterglows.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Field-emission plasma enhancement of H₂–O₂ micro-combustion

In this paper, a detailed three-dimensional computational model is developed to assess the potential of micron-scale field emission dielectric barrier discharge (FE-DBD) plasma actuators in non-premixed microburners with channel heights in the range of L z = 0.25–0.75 mm. Results for H 2 –O 2 combustion with Reynolds number Re = 100 are studied for different configurations of plasma actuator arrays. Without plasma actuation, results agree with corresponding experiments, although in this case the burner typically suffers from incomplete combustion due to thermal quenching, radical quenching, and slow diffusive mixing. For the range of conditions simulated, plasma actuation increases combustion completeness from 25%–70% to 40%–80% by enhancing mixing, generating radicals, and Joule heating. Ionic wind resulting from the FE-DBD plasma disrupts the otherwise simple laminar flow in the burner, accelerating the growth of a mixing layer and enhancing heat transfer to channel walls. The larger, lower temperature flames reduce thermal gradients (and thereby thermal stresses) in the walls. Radical generation due to electron-impact dissociation extends the reaction zone in the diffusion flame and increases combustion completeness. In all cases, the additional heat release with plasma actuation (100–190 W) is significantly larger than the power needed to sustain the plasma (≲0.1 W), suggesting that plasma actuation may provide a significant advantage in energy generation using realistic portable micro-combustion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2008

The Lattice and Thermal Radiation Conductivity of Thermal Barrier Coatings

The lattice and radiation conductivity of thermal barrier coatings was evaluated using a laser heat flux approach. A diffusion model has been established to correlate the apparent thermal conductivity of the coating to the lattice and radiation conductivity. The radiation conductivity component can be expressed as a function of temperature and the scattering and absorption properties of the coating material. High temperature scattering and absorption of the coating systems can also be derived based on the testing results using the modeling approach. The model prediction is found to have good agreement with experimental observations.

Zhu, Dongming↗
DOE OSTI2019

Collective Summary of sCO2 Materials Development Part II: High-Temperature Alloy Corrosion Behavior within Compact Heat Exchangers.

Materials compatibility is a major concern for the design and operation of supercritical carbon dioxide (sCO2) power cycles. Two areas were recently identified for which very little prior knowledge was available. These were the behavior of polymer materials in low-temperature sCO2 environments as well as the high-temperature corrosion behavior for alloys that have been fabricated into compact heat exchangers. A critical need exists to increase understanding in both areas. As such, the Sandia sCO2 Materials Development program initiated a series of experiments for both areas in FY19. The progress that has been made in understanding the behavior of polymers in sCO2 was summarized in the Part I report, while this Part II report describes progress in the area of compact heat exchanger corrosion. For the compact heat exchangers being developed for use in supercritical CO2 power cycles, alloy corrosion is important to understand as it may lead to reduced flow path area, reduced heat transfer, and blocked flow channels. The fabrication of these heat exchangers involve thermal processes such as brazing or diffusion bonding, where the influence of these processes on the corrosion behavior of the alloys is unknown. Candidate alloys for these heat exchangers are typically evaluated for corrosion behavior as witness coupons, without being subjected to these thermal processes. To close this gap in understanding, a series of experiments were completed that utilized small heat exchanger samples subjected to flowing CO2 for 500 hours at 750°C. Small sections of the heat exchanger samples were characterized before and after the 500 hour exposure in order to characterize the oxide growth in the channels as well as the hardness of the alloys. Results are compared to witness coupons of the same alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Proposed Material Properties, Allowable Stresses, and Design Curves of Diffusion Bonded Alloy 800H for the ASME Code Section III Division 5

Abstract Increased interest in compact heat exchangers (CHXs) to serve as intermediate heat exchangers of very high temperature reactors resulted in significant research and development on their design, analysis, and construction. Printed circuit heat exchangers are a type of CHXs with high thermal efficiency and compactness achieved through diffusion bonding a stack of etched plates with millimeter scaled channels. The diffusion bonding process changes the microstructural and mechanical properties of the wrought metal plates. The current nonnuclear design code ASME section VIII, division 1 captures the material property change through a “joint efficiency factor.” However, the current nuclear design code ASME section III, division 5 does not address or support the diffusion bonded material properties. Hence, there is a need to develop allowable stresses, isochronous curves, and fatigue life curves for various diffusion bonded alloys. In this study, Alloy 800H material was selected to establish the diffusion bonded material properties under tension, creep, fatigue, and creep-fatigue loads at elevated temperatures in the range 550–760 °C. A set of tests on diffusion bonded Alloy 800H (DB 800H) were performed and the acquired data are used in developing allowable stresses Sy, Su, Sr, Sm, St, Smt, So, isochronous curves and fatigue life curves according to the ASME section III, division 5 requirements. This paper also presents detailed procedures used in developing the ASME code section III division 5 design provisions for diffusion bonded Alloy 800H.

Engineering↗