Search NASA⌕ Search

SEARCH · Search NASA

Results for “ceramic processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Nano-Engineered Catalyst Supported on Ceramic Hollow Fibers for the Utilization of CO 2 in Dry Reforming to Produce Syngas

The objective of this project was to develop a novel catalytic reactor containing nano-engineered catalysts for the utilization of CO 2 (captured from coal-fired power plants and other CO 2 emitting sources) in dry methane reforming (DMR) (CO 2 + CH 4 → 2 H 2 + 2 CO) to produce synthesis gas (syngas). The technology aims to reduce CO2 emissions by developing beneficial uses for CO 2 from coal-fired power plants. It also offers an alternative to mitigate CO 2 emissions in areas where geologic storage may not be an optimal solution and/or utilization could significantly offset the costs of carbon capture and sequestration. The nano-engineered Ni-based catalyst was prepared by atomic layer deposition (ALD). The Ni particles were as small as ~2-4 nm. The nano-engineered catalyst showed CH 4 conversion >95%, H 2 /CO ratio in the range of 0.7-1.0, and CH 4 reforming rate as high as 2,500 L/h/gNi at 850 ºC and pressure of 15-25 psia. The Ni-based ALD catalyst also showed good stability in DMR reaction during a 200-h continuous operation at 850 °C. This is due to strong bonding between the nanoparticles and substrates since the Ni nanoparticles were chemically bonded to the substrate during the ALD process. The high thermal stability maintains the high dispersion of Ni nanoparticles, which can inhibit coke formation because their step edges are small enough to limit carbon nucleation and growth. Technoeconomic analysis (TEA) indicates the levelized cost of syngas (LCOS) is $172/ton with our technology, which is lower than the equivalent (molar) cost of hydrogen produced by steam methane reforming (SMR) or autothermal reforming (ATR). The major operating cost is natural gas feed and fuel, and the levelized cost is highly sensitive to the price of natural gas and relatively insensitive to the CAPEX. Revenues from syngas could have a significant impact on the net cost of electricity (COE), depending on the cost of natural gas and the selling price of syngas, estimated at $36 per MWh if the syngas were sold at $195 per ton. Following DOE NETL’s guidance, a lifecycle analysis (LCA) was conducted to compare with SMR. The functional unit for the basis of comparison was defined as 1kg carbon monoxide in the product stream. The global warming potential (GWP) of our process was found to be 40% lower than the state-of-the-art SMR process. The sensitivity analysis confirms the emissions are most sensitive to the natural gas fuel requirements to deliver heat to the process.

01 COAL, LIGNITE, AND PEAT↗

Nanoimprinted Diffraction Gratings for Light Trapping in Crystal-Silicon Film Photovoltaics

Crystal-silicon (c-Si) film photovoltaics hold the promise of combining the advantages of state-of-the-art wafer-silicon technology with the scalability and the inherently much lower cost of thin-film solar technologies. In the thickness range of 2-20 μm very effective light trapping is essential to absorb sufficient red and near-infrared (NIR) light and reach targeted efficiencies of 16% 18%, as defined by the U.S. National Solar Technology Roadmap. One proposed method is diffractive light trapping, which, at least in certain wavelength ranges, can theoretically outperform light trapping through random scattering at a rough surface or interface. The goals of this project were (1) to develop a nanoimprinting process for a high-refractive-index dielectric material, (2) to fabricate diffraction gratings as back-reflectors using this material, and (3) to demonstrate for a 2c-Si film an improvement in AM1.5 photon absorption of at least 80% relative to single-pass absorption. We achieved goals (1) and (2). We developed a soft-imprint method for sol-based titanium dioxide precursor films (index range 2.3-2.4) and integrated imprinted films in thin-film silicon devices. We did not fully reach goal (3): depending on the model used for interpretation of the optical experimental data, AM1.5 photon absorption was improved by only 53% (coherent electromagnetic model) to 66% (non-coherent ray-tracing model). When compared to a metallized flat reference film (double-pass absorption), the improvement due to the grating is only 6%, if the (more conservative) electromagnetic model is used. Other important achievements from this project were: • We perfected an imprinting method for another ceramic material, aluminum oxide phosphate, which is index-matched with glass. • We tested diffractive light trapping at different incidence angles and found positive evidence for light trapping for angles up to 50°, although the light-trapping efficiency decreased with increasing incidence angle. • The extent of the trapped wavelength range scales with the refractive index of the dielectric material. The full benefit of a high refractive index, however, is only achieved if the dielectric layer underneath the grating layer (the residual layer) is sufficiently thick (several 100 nm). For a very thin residual layer, the light wave is predominantly localized in the underlying material during diffraction, and this material's refractive index then determines the trapping range. The (welcomed) consequence is that if this material is the silicon absorber layer, e.g. in a thin-film superstrate configuration, a very large trapping range can be achieved even if a low-index dielectric is used. We tested this directly through light-trapping experiments in glass plates using two different imprinted dielectric materials, titanium dioxide (index range 2.3-2.4) and aluminum oxide phosphate (index 1.5), with thick and thin residual layers. • We tested both copper and aluminum as low-cost reflector alternatives to silver on the grating back sides. In the relevant wavelength range above 650 nm, copper not only has the same high reflectance as silver, but the diffraction efficiency is also on par with silver. • A total of five scientific publications resulting from this work have either been published or are in preparation for submission (see Detailed Technical Report, below). Two conference presentations were given. In conclusion, we successfully developed nanoimprinting techniques for two ceramic precursor materials and tested diffractive light trapping in c-Si and nc-Si:H thin-film devices. The measured amount of light trapping did not fully reach our target value. The lessons learned from this project, however, both concerning experimental techniques and theoretical/modeling methods, have been extensive. Light trapping remains a central issue in thin c-Si technology, and we recommend to the US Department of Energy to increase research in this important area.

14 SOLAR ENERGY↗

Continuous Microreactor-Assisted Solution Deposition for Scalable Production of CdS Films

Solution deposition offers an attractive, low temperature option in the cost effective production of thin film solar cells. Continuous microreactor-assisted solution deposition (MASD) was used to produce nanocrystalline cadmium sulfide (CdS) films on fluorine doped tin oxide (FTO) coated glass substrates with excellent uniformity. We report a novel liquid coating technique using a ceramic rod to efficiently and uniformly apply reactive solution to large substrates (152 mm × 152 mm). This technique represents an inexpensive approach to utilize the MASD on the substrate for uniform growth of CdS films. Nano-crystalline CdS films have been produced from liquid phase at ~90°C, with average thicknesses of 70 nm to 230 nm and with a 5 to 12% thickness variation. The CdS films produced were characterized by UV-Vis spectroscopy, transmission electron microscopy, and X-Ray diffraction to demonstrate their suitability to thin-film solar technology.

scalable process↗

A Review of Scalable Hexagonal Boron Nitride ( h -BN) Synthesis for Present and Future Applications

Hexagonal boron nitride (h-BN) is a layered inorganic synthetic crystal exhibiting high temperature stability and high thermal conductivity. As a ceramic material it has been widely used for thermal management, heat shielding, lubrication, and as a filler material for structural composites. Recent scientific advances in isolating atomically thin monolayers from layered van der Waals crystals to study their unique properties has propelled research interest in mono/few layered h-BN as a wide bandgap insulating support for nanoscale electronics, tunnel barriers, communications, neutron detectors, optics, sensing, novel separations, quantum emission from defects, among others. Realizing these futuristic applications hinges on scalable cost-effective high-quality h-BN synthesis. Here, in this work, the authors review scalable approaches of high-quality mono/multilayer h-BN synthesis, discuss the challenges and opportunities for each method, and contextualize their relevance to emerging applications. Maintaining a stoichiometric balance B:N = 1 as the atoms incorporate into the growing layered crystal and maintaining stacking order between layers during multi-layer synthesis emerge as some of the main challenges for h-BN synthesis and the development of processes to address these aspects can inform and guide the synthesis of other layered materials with more than one constituent element. Finally, the authors contextualize h-BN synthesis efforts along with quality requirements for emerging applications via a technological roadmap.

2D materials↗

A step closer to visualizing the electron___phonon interplay

The origin of the very high superconducting transition temperature (Tc) in ceramic copper oxide superconductors is one of the greatest mysteries in modern physics. In the superconducting state, electrons form pairs (known as Cooper pairs) and condense into the superfluid state to conduct electric current with zero resistance. For conventional superconductors, it is well established that the 2 electrons in a Cooper pair are 'bonded' by lattice vibrations (phonons), whereas in high-Tc superconductors, the 'glue' for the Cooper pairs is still under intense discussion. Although the high transition temperature and the unconventional pairing symmetry (d-wave symmetry) have led many researchers to believe that the pairing mechanism results from electron-electron interaction, increasing evidence shows that electron-phonon coupling also significantly influences the low-energy electronic structures and hence may also play an important role in high-Tc superconductivity. In a recent issue of PNAS, Carbone et al. use ultrafast electron diffraction, a recently developed experimental technique, to attack this problem from a new angle, the dynamics of the electronic relaxation process involving phonons. Their results provide fresh evidence for the strong interplay between electronic and atomic degrees of freedom in high-Tc superconductivity. In general, ultrafast spectroscopy makes use of the pump-probe method to study the dynamic process in material. In such experiments, one first shoots an ultrafast (typically 10-100 fs) 'pumping' pulse at the sample to drive its electronic system out of the equilibrium state. Then after a brief time delay ({Delta}t) of typically tens of femtoseconds to tens of picoseconds, a 'probing' pulse of either photons or electrons is sent in to probe the sample's transient state. By varying {Delta}t, one can study the process by which the system relaxes back to the equilibrium state, thus acquiring the related dynamic information. This pump-probe experiment is reminiscent of the standard method used by bell makers for hundreds of years to judge the quality of their products (hitting a bell then listening to how the sound would fade away), albeit the relevant time scale here is way beyond tens of femtoseconds. Traditionally, ultrafast spectroscopy was carried out to study gas-phase reactions, but it has also been applied to study condensed phase systems since the development of reliable solid-state ultrafast lasers approximately a decade ago. In addition, the ability to control pulse width, wavelength, and amplification of the output of Ti:Sapphire lasers has further increased the capability of this experimental method. During the past decade, many ultrafast pump-probe experiments have been carried out in various fields by using different probing methods, such as photo-resistivity, fluorescence yield, and photoemission, and they have revealed much new information complementary to the equilibrium spectroscopy methods used before. Carbone et al. used the photon-pump, electron (diffraction)-probe method. The pumping photon pulse first drives the electrons in the sample into an oscillating mode along its polarization direction. Then during the delay time, these excited electrons can transfer excess energy to the adjacent nuclei and cause crystal lattice vibration on their way back to the equilibrium state. An ultrashort electron pulse is shot at the sample at various time delays {Delta}t and the diffraction pattern is collected. Because the electron diffraction pattern is directly related to the crystal lattice structure and its motion, this technique provides a natural way to study the electron-phonon coupling problem. Furthermore, by adjusting the pump pulse's relative polarization with respect to the Cu-O bond direction, Carbone et al. were able to acquire the electron-phonon coupling strength along different directions. Focusing on the lattice dynamic along the c axis, Carbone et al. found that the c-axis phonons in the optimally-doped Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub 8} (Bi2212) are coupled to the electrons with different strength along different directions within the CuO{sub 2} plane. The coupling strength reaches its largest value along the 2 Cu-O bond directions and becomes the weakest along the bisector of the angle formed by the 2 Cu-O bonds. As pointed out by Carbone et al., these observations agree well with the calculated coupling strength between electrons and the buckling phonons. Furthermore, their observation of this anisotropic electron-phonon coupling also agrees with results from angle-resolved photoemission (ARPES), which measures the equilibrium-state properties of materials. In ARPES measurements, electron-phonon coupling manifests itself as a kink anomaly in the band dispersion and a corresponding sudden broadening in the spectral width.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Garnet Electrolyte Surface Degradation and Recovery

Ceramic materials based on the garnet structure Li 7 La 3 Zr 2 O 12 (LLZO) show great promise as lithium-ion conducting electrolytes for solid-state lithium batteries. However, these materials exhibit surface degradation when exposed to air and moisture, which adversely impacts their functioning in operating devices. In this work, we use several depth-profiling and in situ techniques to probe the nature of the surface reactions that occur when aluminum (Al)-substituted LLZO is exposed to air. These experiments show that a proton exchange reaction occurs near the surface of the LLZO and leads to change in its chemistry and structure, concomitant with the formation of Li 2 CO 3 . But these reactions can be readily reversed by heating samples at 250 °C under an inert atmosphere to recover LLZO surface chemistry and structure. Symmetrical cells containing samples treated this way exhibited much lower area specific impedances than those containing air-exposed LLZO without the treatment, confirming the reversal of the degradation process. Finally, our results show a process to rejuvenate LLZO surface, and this opens the possibility of integrating this material in solid-state devices.

25 ENERGY STORAGE↗

HSQC spectra of lignin isolated from poplar stems

Here we present a curated dataset of two-dimensional heteronuclear single quantum coherence (HSQC) nuclear magnetic resonance (NMR) spectra of lignin isolated from stems of genetically engineered poplar through auxin signaling gene modification. The plants were grown in greenhouse with temperatures between 21 and 23 °C. Plants were harvested and the aboveground stems were cut off an approximately five-inch-long segment from the bottom end of the plant stem, debarked and air-dried for three weeks. The dried stem samples were Wiley milled (mesh size 20), Soxhlet-extracted with toluene/ethanol for 24 h to remove extractives. The extracted biomass was ball-milled in a Retsch PM100 planetary ball mill using a porcelain jar with ceramic balls at 600 rpm for 2 h (in 5 min on and 5 min off cycles to avoid excessive sample heating). The ball-milled materials were then subjected to enzymatic hydrolysis for 48 h followed by centrifugation and washing with deionized water. The solid residue was freeze-dried to recover the lignin. The dry stem lignin samples were dissolved in deuterated dimethyl sulfoxide (d6) and transferred into a 5 mm tube. 13C–1H HSQC experiments were performed in a Bruker Avance III HD 500 MHz NMR spectrometer operating at a frequency of 125.12 MHz for the 13C nucleus using a standard Bruker pulse sequence on a Prodigy platform cryoprobe. The NMR spectra were acquired under the following acquisition conditions: 230 ppm spectral width in F1 (13C) dimension with 256 data points and 12 ppm spectral width in F2 (1H) dimension with 2048 data points, a 90° pulse, a one bond C–H coupling constant of 145 Hz, a 1.0 s pulse delay, and 64 scans. Spectra were processed using the Bruker TopSpin 3.6 software. Additional meta data is embedded in the raw spectra figures.

HSQC, lignin, poplar, stems, CBI↗

Fabrication of AlN/BN bishell hollow nanofibers by electrospinning and atomic layer deposition

Aluminum nitride (AlN)/boron nitride (BN) bishell hollow nanofibers (HNFs) have been fabricated by successive atomic layer deposition (ALD) of AlN and sequential chemical vapor deposition (CVD) of BN on electrospun polymeric nanofibrous template. A four-step fabrication process was utilized: (i) fabrication of polymeric (nylon 6,6) nanofibers via electrospinning, (ii) hollow cathode plasma-assisted ALD of AlN at 100 °C onto electrospun polymeric nanofibers, (iii) calcination at 500 °C for 2 h in order to remove the polymeric template, and (iv) sequential CVD growth of BN at 450 °C. AlN/BN HNFs have been characterized for their chemical composition, surface morphology, crystal structure, and internal nanostructure using X-ray photoelectron spectroscopy, scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy, and selected area electron diffraction. Measurements confirmed the presence of crystalline hexagonal BN and AlN within the three dimensional (3D) network of bishell HNFs with relatively low impurity content. In contrast to the smooth surface of the inner AlN layer, outer BN coating showed a highly rough 3D morphology in the form of BN nano-needle crystallites. It is shown that the combination of electrospinning and plasma-assisted low-temperature ALD/CVD can produce highly controlled multi-layered bishell nitride ceramic hollow nanostructures. While electrospinning enables easy fabrication of nanofibrous template, self-limiting reactions of plasma-assisted ALD and sequential CVD provide control over the wall thicknesses of AlN and BN layers with sub-nanometer accuracy.

36 MATERIALS SCIENCE↗

F3D Image Processing and Analysis for Many - and Multi-core Platforms

F3D is written in OpenCL, so it achieve[sic] platform-portable parallelism on modern mutli-core CPUs and many-core GPUs. The interface and mechanims to access F3D core are written in Java as a plugin for Fiji/ImageJ to deliver several key image-processing algorithms necessary to remove artifacts from micro-tomography data. The algorithms consist of data parallel aware filters that can efficiently utilizes[sic] resources and can work on out of core datasets and scale efficiently across multiple accelerators. Optimizing for data parallel filters, streaming out of core datasets, and efficient resource and memory and data managements over complex execution sequence of filters greatly expedites any scientific workflow with image processing requirements. F3D performs several different types of 3D image processing operations, such as non-linear filtering using bilateral filtering and/or median filtering and/or morphological operators (MM). F3D gray-level MM operators are one-pass constant time methods that can perform morphological transformations with a line-structuring element oriented in discrete directions. Additionally, MM operators can be applied to gray-scale images, and consist of two parts: (a) a reference shape or structuring element, which is translated over the image, and (b) a mechanism, or operation, that defines the comparisons to be performed between the image and the structuring element. This tool provides a critical component within many complex pipelines such as those for performing automated segmentation of image stacks. F3D is also called a "descendent" of Quant-CT, another software we developed in the past. These two modules are to be integrated in a next version. Further details were reported in: D.M. Ushizima, T. Perciano, H. Krishnan, B. Loring, H. Bale, D. Parkinson, and J. Sethian. Structure recognition from high-resolution images of ceramic composites. IEEE International Conference on Big Data, October 2014.

Source record↗

F3D Image Processing and Analysis for Many - and Multi-core Platforms

F3D is written in OpenCL, so it achieve[sic] platform-portable parallelism on modern mutli-core CPUs and many-core GPUs. The interface and mechanims to access F3D core are written in Java as a plugin for Fiji/ImageJ to deliver several key image-processing algorithms necessary to remove artifacts from micro-tomography data. The algorithms consist of data parallel aware filters that can efficiently utilizes[sic] resources and can work on out of core datasets and scale efficiently across multiple accelerators. Optimizing for data parallel filters, streaming out of core datasets, and efficient resource and memory and data managements over complex execution sequence of filters greatly expedites any scientific workflow with image processing requirements. F3D performs several different types of 3D image processing operations, such as non-linear filtering using bilateral filtering and/or median filtering and/or morphological operators (MM). F3D gray-level MM operators are one-pass constant time methods that can perform morphological transformations with a line-structuring element oriented in discrete directions. Additionally, MM operators can be applied to gray-scale images, and consist of two parts: (a) a reference shape or structuring element, which is translated over the image, and (b) a mechanism, or operation, that defines the comparisons to be performed between the image and the structuring element. This tool provides a critical component within many complex pipelines such as those for performing automated segmentation of image stacks. F3D is also called a "descendent" of Quant-CT, another software we developed in the past. These two modules are to be integrated in a next version. Further details were reported in: D.M. Ushizima, T. Perciano, H. Krishnan, B. Loring, H. Bale, D. Parkinson, and J. Sethian. Structure recognition from high-resolution images of ceramic composites. IEEE International Conference on Big Data, October 2014.

Source record↗

Characterizing mechanical and microstructural properties of novel montmorillonite-rich polyethylene composites

Montmorillonite (MMT) clays are important industrial materials used as catalysts, chemical sorbents and fillers in polymer–clay nanocomposites. The layered structure of these clays has motivated research into further applications of these low-cost materials, including use as ion exchange media and solid-state ionic conductors. In these applications, the mechanical properties of MMT are key when considering long-term, reliable performance. Previous studies have focused on the mechanical properties of nanocomposites with MMT as the minority component or pure MMT thin films. In this work, the microstructure and mechanical properties of pure MMT and majority MMT/polyethylene composites pressed into dense pellets are examined. Characterization methods such as X-ray diffraction, atomic force microscopy and scanning electron microscopy together with nanoindentation reveal important structure–property relationships in the clay-based materials. Here, utilizing these techniques, we have discovered that MMT processing impacts the layered microstructure, chemical stability and, critically, the elastic modulus and hardness of bulk MMT samples. Particularly, the density of the pellets and the ordering of the clay platelets within them strongly influence the elastic modulus and hardness of the pellets. By increasing pressing force or by incorporating secondary components, the density, and therefore mechanical properties, can be increased. If the layered structure of the clay is destroyed by exfoliation, the mechanical properties will be compromised. Understanding these relationships will help guide new studies to engineer mechanically stable MMT-based materials for industrial applications.

36 MATERIALS SCIENCE↗

Irradiation-induced β to α SiC transformation at low temperature

Here, we observed that β-SiC, neutron irradiated to 9 dpa (displacements per atom) at ≈1440 °C, began transforming to α-SiC, with radiation-induced Frank dislocation loops serving as the apparent nucleation sites. 1440 °C is a far lower temperature than usual β → α phase transformations in SiC. SiC is considered for applications in advanced nuclear systems, as well as for electronic or spintronic applications requiring ion irradiation processing. β-SiC, preferred for nuclear applications, is metastable and undergoes a phase transformation at high temperatures (typically 2000 °C and above). Nuclear reactor concepts are not expected to reach the very high temperatures for thermal transformation. However, our results indicate incipient β → α phase transformation, in the form of small (~5–10 nm) pockets of α-SiC forming in the β matrix. In service transformation could degrade structural stability and fuel integrity for SiC-based materials operated in this regime. However, engineering this transformation deliberately using ion irradiation could enable new electronic applications.

36 MATERIALS SCIENCE↗

Mechanical properties of high-entropy alloys with emphasis on face-centered cubic alloys

HHigh-entropy alloys (HEAs), also known as multi-principal element alloys or multi-component alloys, have been the subject of numerous investigations since they were first described in 2004. The earliest HEA was the equiatomic CrMnFeCoNi “Cantor” alloy, but HEAs now encompass a broad class of metallic and ceramic systems. The concept of utilizing the high entropy of mixing to develop stable multi-element alloys may not be scientifically correct but has produced extraordinary mechanical properties in specific HEAs, mainly CrCoNi-based alloys, associated with their continuous work-hardening rate that is sustained to large plastic strains (~0.5) and at low temperatures. This, in combination with the high frictional forces on dislocations and a propensity for twinning, leads to outstandingly high fracture toughness values (exceeding 200 MPa·m 1/2 ) and resistance to shear-band formation under dynamic loading. The critical shear strain for the onset of adiabatic shear band formation is ~7 for the Cantor alloy, much higher than that for conventional alloys, suggesting superior ballistic properties. The slower diffusion rates resulting from the multi-element environment contribute to the excellent intermediate-temperature performance. We review the principal mechanical properties of these alloys with emphasis on the face-centered cubic systems, such as the CrCoNi-based alloys. Their favorable mechanical properties and ease of processing by conventional means suggest extensive utilization in many future structural applications.

36 MATERIALS SCIENCE↗

Processing and characterization of the homologous Zr x Ta 2 O 2x+5 series

In this study, Zr x Ta 2 O 2x+5 (ZTOx) was systematically studied to determine ideal solid-state synthesis and pressureless sintering conditions. For Zr 6 Ta 2 O 17 (ZTO6) and other compositions with values of x in ZTOx the optimal synthesis temperature of 1100 °C with 1 h dwell time was optimal. XRD phase analysis of the homologous series indicated that for ZTOx, x = 5, 6, 7, and 8 were within the phase stability field while x = 4 and x = 9 were outside the phase stability field. Unit cell lattice parameters changed anisotropically with Zr:Ta ratio with an overall <0.1% change in unit cell volume across the solid solution. Some Raman modes red shifted while others blue shifted, indicating competing tensile and compressive strains. Sintering of ZTOx required a progressively higher temperature as Zr-content increased despite the same starting powder grain sizes and synthesis temperature. Higher Vickers hardness for Zr-rich (12.7–12.8 GPa) than Ta-rich Zr x Ta 2 O 2x+5 (11.6–11.7 GPa) disappeared when accounting for different sintering temperatures. Indentation toughness was similar for all compositions (1.2–1.4 MPa m 1/2 ). Properties of Zr x Ta 2 O 2x+5 series indicate tunability of Zr:Ta composition ratio while maintaining the structure and room temperature mechanical properties comparable to Hf 6 Ta 2 O 17 and 8 mol% yttria stabilized zirconia ceramics.

36 MATERIALS SCIENCE↗

How Proton Incorporation Reshapes Lattice Dynamics In BaSnO 3 ‐Type Proton Conductors

Proton conduction in acceptor-doped perovskites is fundamentally a vibronic process: mobile H + and D + do not move independently, but dynamically co-vibrate with the surrounding oxygen–metal framework. Direct experimental evidence for this behavior is presented using in situ 119⁢ 𝑆⁢𝑛 nuclear resonance vibrational spectroscopy (NRVS) on hydrated, deuterated, and dry 𝐵⁢𝑎⁢𝑆⁢𝑛 1−𝑥⁢ 𝑌 𝑥 ⁢𝑂 3−𝛿 . Hydration induces systematic redistributions in the Sn-projected phonon density of states (PDOS), including an upshift of the first spectral moment by about 0.4 meV, indicating a stiffening of the extended Sn–O network. H/D isotopic substitution leaves the Sn-projected PDOS largely unchanged, with only subtle isotope-dependent spectral reweighting, demonstrating that protonic degrees of freedom are not localized oscillators but are embedded in collective lattice modes. These results are rationalized using a classical coupled proton–phonon oscillator model that links the observed PDOS variations to changes in effective force constants and vibrational mass terms. The model captures how H + and D + participate in cooperative lattice dynamics rather than forming isolated OH/OD entities. Overall, NRVS probes proton–lattice coupling in ceramic proton conductors and quantitatively describes how protonic defects modulate host lattice dynamics to enable phonon-assisted long-range proton transport.

36 MATERIALS SCIENCE↗

Role of Titanium, Carbon, Boron, and Zirconium in Carbide and Porosity Formation during Equiaxed Solidification of Nickel-Based Superalloys

This work analyses the effect of Ti in the MC carbide formation and also in the γ/γ´ eutectic promotion in two nickel-based alloys melted under vacuum conditions and solidified into ceramic molds. The role of boron, carbon and zirconium on the porosity level after solidification of both alloys was also investigated; since the alloys were vacuum melted, it is assumed that the observed porosity is due to micro-shrinkage. The chemical compositions for two alloys were: 20.2Cr-13.7Co-4.78Mo-1.19Al-0.69Ti-0.08C-2.34Fe for Alloy 1, and 20.5Cr-15.6Co5.03Mo-1.57Al-3.42Ti-0.15C-1.64Fe-0.076Zr-0.01%B for Alloy 2. Results showed a higher volume fraction of MC carbides and the γ/γ´ eutectic for the Alloy 2 with higher titanium content since this element is a carbide and γ/γ´ eutectic promoter. The porosity level in the Alloy 2, with higher amounts of carbon, boron and zirconium was considerably lower than that for the Alloy 1. These results are discussed in terms of different phenomena caused by the segregating effects of boron, carbon and zirconium towards the interdendritic regions and the formation of zirconium carbides that produce an expansion in volume when they are formed at the end of the solidification process.

36 MATERIALS SCIENCE↗

Preface to the JPCM special issue on intense radiation sources in condensed matter and materials physics

This special issue is designed to honour the contributions of our colleague Neville Greaves who was among the first to apply newly-available synchrotron x-ray techniques to study the synthesis, structures and properties of advanced materials [1, 2]. His wide ranging work on ceramics, glasses and nanomaterials was celebrated in a recent issue of the J. Non-Cryst. Solids [3]. Neville's contributions to synchrotron research, highlighted here, focussed on design and construction of new beamline capabilities and sample environments to probe materials under different physical and chemical conditions, integrating various techniques to obtain complementary data on structure and bonding. The innovative nature of his work is illustrated by his studies of liquids and glasses, where he incorporated aerodynamic levitation into these experimental techniques, using both synchrotron x-ray and neutron beams to probe the structural transformations and dynamics combined with molecular dynamics simulations to study atomic scale organisation. His work has had a major impact on fundamental condensed matter physics and chemistry as well as applied materials science; and in this issue, we present contributions from colleagues using and developing new experimental techniques at current and next-generation synchrotron, neutron and free-electron laser sources and in their own laboratories, that probe the fundamental physics, chemistry and functional properties of novel materials and processes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗