Search NASA⌕ Search

SEARCH · Search NASA

Results for “composite optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Structural Sizing of a Tow-Steered Truss-Braced Wing Box Test Article

Tailoring of composite laminates is traditionally performed by changing the orientation of straight fibers in one or more plies. Modern automated fiber placement machines facilitate placement of bundles of curved fibers (tows) in a process called tow-steering, but additional variables must be used to define the shapes of tow-steered fiber paths. In this paper, the design of a tow-steered truss-braced wing test article called the Structural Wing Experiment Evaluating Truss-bracing 15-ft concept (SWEET-15) is discussed. The SWEET-15 test article is scaled to 18.6% of the span length and chord width of a full-scale vehicle. The test article is designed to withstand +2.5-g (positive limit) and -1.0-g (negative limit) maneuvering loads with a factor of safety of 1.5 under strength and buckling constraints. Design studies were performed using commercial finite element analysis and optimization software in conjunction with a tow-steering modeling tool called ATSCOOL (Automated Tool for Steered COmposite Optimizable Laminates) developed at NASA Langley Research center. A 6.4% weight reduction in the upper cover panels was achieved using a tow-steered layup configuration.

Structural Optimization↗

Quasieigenstate Coalescence in an Atom-Cavity Quantum Composite

We report the first direct observation of an exceptional point (EP) in an open quantum composite of a single atom and a high-Q cavity mode. The atom-cavity coupling constant was made a continuous variable by utilizing the multisublevel nature of a single rubidium atom when it is optimally coupled to the cavity mode. The spectroscopic properties of quasieigenstates of the atom-cavity composite were experimentally investigated near the EP. Branch-point singularity of quasieigenenergies was observed and its 4{pi} symmetry was demonstrated. Consequently, the cavity transmission at the quasieigenstate was observed to exhibit a critical behavior at the EP.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Optimized Extraction Method To Remove Humic Acid Interferences from Soil Samples Prior to Microbial Proteome Measurements

The microbial composition and their activities in soil environments play a critical role in organic matter transformation and nutrient cycling, perhaps most specifically with respect to impact on plant growth but also more broadly to global impact on carbon and nitrogen-cycling. Liquid chromatography coupled to high performance mass spectrometry provides a powerful approach to characterize soil microbiomes; however, the limited microbial biomass and the presence of abundant interferences in soil samples present major challenges to soil proteome extraction and subsequent MS measurement. To address some of the major issues, we have designed and optimized an experimental method to enhance microbial proteome extraction concomitant with minimizing the soil-borne humic substances co-extraction from soils. Among the range of interferences, humic substances are often the worst in terms of adversely impacting proteome extraction and mass spectrometry measurement. Our approach employs an in-situ detergent-based microbial lysis / TCA precipitation coupled with an additional acidification precipitation step at the peptide level which efficiently removes humic acids. By combing filtration and pH adjustment of the final peptide solution, the remaining humic acids can be differentially precipitated and removed with a membrane filter, thereby leaving much cleaner proteolytic peptide samples for MS measurement. As a result, this modified method is a reliable and straight-forward protein extraction method that efficiently removes soil-borne humic substances without inducing proteome sample loss or reducing or biasing protein identification in mass spectrometry.

59 BASIC BIOLOGICAL SCIENCES↗

Concurrent material-fabrication optimization of metal-matrix laminates under thermo-mechanical loading

A methodology is developed to tailor fabrication and material parameters of metal-matrix laminates for maximum loading capacity under thermomechanical loads. The stresses during the thermomechanical response are minimized subject to failure constrains and bounds on the laminate properties. The thermomechanical response of the laminate is simulated using nonlinear composite mechanics. Evaluations of the method on a graphite/copper symmetric cross-ply laminate were performed. The cross-ply laminate required different optimum fabrication procedures than a unidirectional composite. Also, the consideration of the thermomechanical cycle had a significant effect on the predicted optimal process.

Saravanos, D. A.↗

Effect of heat input on dissimilar welds of ultra high strength steel and duplex stainless steel: Microstructural and compositional analysis

The effect of heat input on the microstructure and compositional heterogeneity of welds of direct-quenched ultra high strength steel (Optim 960 QC) and duplex stainless steel (UNS S32205) was studied. The dissimilar welds were made using GMAW with a fully austenitic filler wire. In addition to grain coarsening in the heat affected zone (HAZ) of the ferritic side, it was found that an increase in heat input correlatively increased the proportional volume of bainitic to martensitic phases. Coarse ferritic grains were observed in the duplex HAZ. Higher heat input, however, had a beneficial effect on the nucleation of austenite in the HAZ. Heat input had a regulatory effect on grain growth within the austenitic weld and more favorable equiaxed austenite was obtained with higher heat input. On the ferritic side of the welds, macrosegregation in the form of a martensitic intermediate zone was observed for all the cooling rates studied. However, on the duplex side, macrosegregation in the fusion boundary was only noticed with higher cooling rates. Microstructural observations and compositional analysis suggest that higher heat input could be beneficial for the structural integrity of the weld despite higher heat input increasing the extent of adverse coarse grains in the HAZ, especially on the ferritic side. - Highlights: •The effect of heat input on dissimilar welds of UHSS and DSS was studied. •Transmutation of the microstructure was discussed in detail. •The influence of heat input on compositional heterogeneity of welds was described. •Higher heat input enhanced bainitic transformation on the ferritic side. •Macrosegregation was affected by the amount of heat input on the DSS side.

36 MATERIALS SCIENCE↗

Preparation and characterization of Pb(Lu1/2Nb1/2)O3-Pb(Ni1/3Nb2/3)O3-PbTiO3 ternary ferroelectric ceramics with high piezoelectric constant

Highlights: • PLN-PNN-PT ternary ferroelectric systems were prepared by two-step method. • PLN-PNN-PT ceramics exhibit typical relaxor behavior. • 0.17PLN-0.47PNN-0.36PT ceramic has optimal properties (T{sub C} ∼ 142 °C, d{sub 33} ∼ 378 pC/N). - Abstract: Pb(Lu{sub 1/2}Nb{sub 1/2})O{sub 3}-Pb(Ni{sub 1/3}Nb{sub 2/3})O{sub 3}-PbTiO{sub 3} ferroelectric ceramics were successfully prepared by a modified two-step columbite precursor method. The structural, dielectric, ferroelectric and piezoelectric properties were characterized by X-ray diffraction, ferroelectric and dielectric measurements. All the obtained samples have pure perovskite structure. The composition of 0.17PLN-0.47PNN-0.36PT within morphotropic phase boundary exhibits optimal properties with piezoelectric coefficient d{sub 33} = 378 pC/N, Curie temperature Tc = 142 °C, dielectric constant ε΄ = 4700, dielectric loss tangent tanδ = 0.05, remnant polarization Pr = 27.1 μC/cm{sup 2} and coercive field Ec = 8.89 KV/cm. According to Curie-Weiss Law and Lorentz-type quadratic relationship, the dielectric behavior was studied and the relaxor factor γ is between 1.55–1.87, indicating the character of diffuse phase transition of the Pb(Lu{sub 1/2}Nb{sub 1/2})O{sub 3}-Pb(Ni{sub 1/3}Nb{sub 2/3})O{sub 3}-PbTiO{sub 3} ceramics. The excellent piezoelectric properties and high Curie temperature make this system a promising material for high-power transducer applications in a broad temperature range.

36 MATERIALS SCIENCE↗

Optimal expression evaluation for data parallel architectures

A data parallel machine represents an array or other composite data structure by allocating one processor per data item. A pointwise operation can be performed between two such arrays in unit time, provided their corresponding elements are allocated in the same processors. If the arrays are not aligned in this fashion, the cost of moving one or both of them is part of the cost of operation. The choice of where to perform the operation then affects this cost. If an expression with several operands is to be evaluated, there may be many choices of where to perform the intermediate operations. An efficient algorithm is given to find the minimum cost way to evaluate an expression, for several different data parallel architectures. The algorithm applies to any architecture in which the metric describing the cost of moving an array has a property called robustness. This encompasses most of the common data parallel communication architectures, including meshes of arbitrary dimension and hypercubes.

Gilbert, J. R.↗

Optimal expression evaluation for data parallel architectures

A data parallel machine represents an array or other composits data structure by allocating one processor per data item. A pointwise operation can be performed between two such arrays in unit time, provided their corresponding elements are allocated in the same processors. If the arrays are not aligned in this fashion, the cost of moving one or both of them is part of the cost of operation. The choice of where to perform the operation then affects this cost. If an expression with several operands is to be evaluated, there may be many choices of where to perform the intermediate operations. An efficient algorithm is given to find the minimum cost way to evaluate an expression, for several different data parallel architectures. The algorithm applies to any architecture in which the metric describing the cost of moving an array has a property called robustness. This encompasses most of the common data parallel communication architectures, including meshes of arbitrary dimension and hypercubes.

Gilbert, John R.↗

Optimal expression evaluation for data parallel architectures

A data parallel machine represents an array or other composite data structure by allocating one processor (at least conceptually) per data item. A pointwise operation can be performed between two such arrays in unit time, provided their corresponding elements are allocated in the same processors. If the arrays are not aligned in this fashion, the cost of moving one or both of them is part of the cost of the operation. The choice of where to perform the operation then affects this cost. If an expression with several operands is to be evaluated, there may be many choices of where to perform the intermediate operations. An efficient algorithm is given to find the minimum-cost way to evaluate an expression, for several different data parallel architectures. This algorithm applies to any architecture in which the metric describing the cost of moving an array is robust. This encompasses most of the common data parallel communication architectures, including meshes of arbitrary dimension and hypercubes. Remarks are made on several variations of the problem, some of which are solved and some of which remain open.

Gilbert, John R.↗

Manufacturing and Scale-Up of Natural Fiber Composite eVTOL Propeller Skin and C-Channel

This report presents the manufacturing and scale-up of natural fiber composites for aerospace applications, conducted within NASA’s Convergent Aeronautics Solutions portfolio to advance aircraft capabilities and efficiency. The effort focused on the development and demonstration of two proof-of-concept articles, an Electric Vertical Take-off and Landing (eVTOL) propeller skin and a C-channel, produced through an iterative design and process optimization approach. Best practices and guidance on addressing key challenges with bio-based composite materials and manufacturing is provided. Ideally suited for non-load-bearing structural components, these emerging materials offer potential for weight reduction, vibration damping, noise mitigation, interference-free communication, and cost savings, without compromising the performance of safety-critical primary structures.

Natural fibers↗

Thermal analysis of a functionally graded material subject to a thermal gradient using the boundary element method

The boundary element method is utilized in this study to conduct thermal analysis of functionally graded composites, materials in which the internal microstructure or properties are explicitly tailored in order to obtain an optimal response, on the micromechanical (constituent) scale. A unique feature of the boundary element formulations used here is the use of circular shape functions to convert the two-dimensional integrations of the composite fibers to one dimensional integrations. Using the computer code BEST-CMS, the through the thickness temperature profiles are computed for a representative material with varying numbers of fibers and fiber spacing in the thickness direction. The computed temperature profiles are compared to those obtained using an alternate analytical theory which explicitly couples the heterogeneous microstructure to the global analysis. The boundary element results compared favorably to the analytical calculations, with discrepancies that are explainable based on the boundary element formulation. The results serve both to demonstrate the ability of the boundary element method to analyze these types of materials, and to verify the accuracy of the analytical theory.

Goldberg, Robert K.↗

CoSn-type NiIn1–xSbx (0 ≤ x ≤ 0.17): Site-Selective Substitution, Electronic Structure, Chemical Bonding, and Structural Transformation

CoSn-type intermetallic compounds have emerged as a model platform for Kagome-derived flat-band physics, where subtle chemical perturbations can strongly influence electronic structure and phase stability. Here, we present a combined experimental and theoretical study of Sb-substitution in CoSn-type NiIn1–xSbx (0 ≤ x ≤ 0.17) to elucidate the interplay between site selectivity, solubility limit, chemical bonding, and electronic structure. Rietveld refinements on Neutron powder diffraction data confirmed the selective Sb-substitution at the electron-rich In2 (2d) site forming the honeycomb substructure, while the In1 (1a) site within the Kagome layer remains exclusively occupied by In. Density functional theory (DFT) calculations revealed that pristine CoSn-type NiIn hosts Ni 3d-dominated flat bands near the Fermi level (EF), originating from the Kagome-like Ni substructure. Partial replacement of In by Sb within the honeycomb layer alters these flat-band features below EF, reducing the density of states and suppressing the flat-band topology near the Fermi level. Orbital-resolved electronic structure and chemical-bonding analyses show that Sb-substitution enhances Ni-p-block (In/Sb) covalency and optimizes charge compensation, stabilizing the CoSn-type structure up to the solubility limit x ≈ 0.17. Beyond the limit, the higher-Sb compositions show satellite reflections consistent with an incommensurately modulated phase. These results establish a link between site-selective chemical substitution, bonding optimization, and flat-band electronic structure evolution, providing fundamental insights into how chemical substitution influences the electronic properties of Kagome-based intermetallic compounds.

Roy, Nilanjan [National Institute of Technology Si↗

Infiltration/cure modeling of resin transfer molded composite materials using advanced fiber architectures

A model was developed which can be used to simulate infiltration and cure of textile composites by resin transfer molding. Fabric preforms were resin infiltrated and cured using model generated optimized one-step infiltration/cure protocols. Frequency dependent electromagnetic sensing (FDEMS) was used to monitor in situ resin infiltration and cure during processing. FDEMS measurements of infiltration time, resin viscosity, and resin degree of cure agreed well with values predicted by the simulation model. Textile composites fabricated using a one-step infiltration/cure procedure were uniformly resin impregnated and void free. Fiber volume fraction measurements by the resin digestion method compared well with values predicted using the model.

Loos, Alfred C.↗

Bubbler Design Updates for Nuclear Safeguards Applications

The accurate monitoring of molten salt compositions is crucial for nuclear safeguards, particularly in the context of mixtures used in molten salt reactors as well as pyroprocessing. However, for nuclear material accountancy in actinide bearing molten salts, the solution volume is also needed to determine the total mass of material in the salt. This study explores the effectiveness of two bubbler configurations, triple and single, for density and level measurements within these molten salts for salt volume determinations. The triple bubbler system utilizes three gas dip-tubes strategically positioned at different heights within the molten salt. With this design, the molten salt level, density, and surface tension can be determined simultaneously. The single bubbler configuration, on the other hand, relies on a dynamic single dip-tube to determine the density and level. Both configurations will be tested in aqueous solutions as well as in LiCl-KCl and NaCl-MgCl2 molten salts between 450°C and 750°C. Dip-tube diameters and bubbler inferences will also be explored. A new bubbler is being designed based on results. The findings of this study will provide valuable insights into the optimal bubbler design and configuration for ensuring representative sampling of molten salt compositions in nuclear safeguards applications. This will contribute to enhanced accountability and transparency in the monitoring of actinide bearing molten salts, promoting nuclear safeguards objectives.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Manufacturing and Validation of a Novel Composite Component for Aircraft Main Landing Gear Bay

Composite materials may reduce the final weight of the aircraft structural components, in addition to improve fatigue performance and corrosion resistance. In order to achieve the optimization of air transport systems, making them increasingly sustainable, the structural design must be surely reviewed, starting to follow the “composite thinking” philosophy. The present research provides some relevant outcomes concerning the design of a composite sample for the main landing gear bay of a large commercial airplane (EASA CS25 category), within ITEMB (integrated full composite main landing gear bay concept) project, a program of Clean Sky 2 EU research framework. The most ambitious goal is to develop a new generation of lower center fuselage (LCF) with an innovative integrated landing system in the fuselage, which is considered the next frontier in the development of landing systems for medium-haul aircraft, such as the Airbus A320 aircraft family. The development of a different architecture, with the landing gear integrated within the related fuselage bay, could lead to a simplification of the whole subassembly with potential advantage in terms of construction and assembly times. Final target of the project is the manufacturing of an innovative monolithic composite structure that will replace the actual configuration (a mixed structure of metal and composite subassemblies) reducing or actually removing all the cost of assembly and increasing the production rate. This paper presents the main results of the work, introducing the main processing steps and prototype results; in the last part of the work, also some experimental tests on significant element are introduced as the first assessment of the technology readiness level that has been achieved.

36 MATERIALS SCIENCE↗

Antibacterial and Structural Properties and Printability of Starch/Clay/Polyethylene Composite Films

A composite of thermoplastic starch (TPS), low-density polyethylene (LDPE) and citric acid-modified montmorillonite (CMMT) was prepared in a twin screw extruder for packaging film application. Starch was first converted to the thermoplastic state by using sorbitol and water. Composite films were produced on a chill roll system and then were modified for printability by grafting of acrylonitrile onto the starch backbone. Antimicrobial property and printability of the films were studied from which the sample with the highest antimicrobial property and the best printability was selected. This optimal sample was then characterized by Fourier transform infrared, thermal gravimetric analysis, differential scanning calorimetry, X-ray diffraction, and scanning electron microscopy. The composite film showed a matrix/dispersed morphology in which LDPE formed a continuous phase and TPS/CMMT nanocomposite particles appeared as dispersed phase. Biodegradability, water absorption, oxygen permeability, tensile strength and transparency of optimal film were also studied. The results indicated very good properties of the produced composite film for packaging application. Graphical Abstract: .

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Low-Activation Joining of SiC/SiC Composites for Fusion Applications

Abstract Research at PNNL has been directed at high-strength, low-activation joints using solid-state displacement reactions. This paper reports on further development and optimization of displacement reaction joints for the TITAN collaboration. The results reveal that fully dense and high-quality joints between SiC-composite bars are fabricated at 1623K to 1723K using 30 MPa pressure in purified argon atmospheres. Scanning electron micrographs reveal typical interpenetrating phase microstructures in the joints, which are about 10 µm thick. Blocky SiC particles are observed to nucleate preferentially at the SiC-joint interface but are more plate-like within the joint. X-ray spectroscopy reveals a uniform distribution of constituent elements consistent with the interpenetrating phases.

Henager, Charles H.↗

Aeroservoelastic tailoring for lateral control enhancement

The application of an automated optimization approach to the integrated structural and control design of an aircraft wing and its control surface is illustrated. The performance index or cost function for optimization is the aileron hinge moment required to sustain a specified terminal roll rate at a chosen design speed at which aeroelastic effects are significant. The design variables used for aileron hinge-moment minimization are the aileron flap-to-chord ratio; the location of the aileron with respect to the roll axis; and the orientations of three advanced composite plies comprising 60 percent of the wing structure. The effects of aileron location and advanced composite ply orientation on the terminal roll rate and aileron hinge moment are examined. Optimization is seen to involve a compromise between a laminated structure/aileron combination that is effective in creating large rolling moments and one that minimizes the damping-in-roll. These two requirements are in conflict; the optimization driver must locate a compromise design point by moving the control surface and changing its size while also creating a suitable structural design.

Weisshaar, Terrence A.↗