Search NASA⌕ Search

SEARCH · Search NASA

Results for “difference frequency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Modulation of microstructure and optical properties of Mo-doped ZnO thin films by substrate temperature

Highlights: • Mo-doped ZnO films are obtained by sputtering at various substrate temperatures. • High-quality MZO thin films with good crystalline have been obtained at 200 °C. • Deposition temperature affects the amount of defects in the crystalline structure - Abstract: Mo-doped ZnO(MZO) films were deposited on Si (1 1 1) substrates by radio frequency sputtering at different substrate temperatures of 200, 300 and 400 °C. The effect of the substrate temperature on the structural and optical properties of the MZO films has been investigated. X-ray diffraction results reveal that all the films are polycrystalline with a hexagonal wurtzite structure with a preferential orientation according to the direction (0 0 2) plane. The crystallinity and surface morphologies of the films are strongly dependent on the growth temperature, which in turn exerts a great effect on microstructural and optical properties of the MZO films. The optical absorption measurements show high ultraviolet (UV) absorbance property of MZO with sharp and intense absorption band in this region and the optical band gap (E{sub g}) are 3.18, 3.22, 3.25 and 3.21 eV for the films deposited at room temperature, 200, 300 and 400 °C. The photoluminescence (PL) intensity of a strong broad violet–blue emission from MZO nanostructures with increasing deposited temperature was also observed. X-ray photoelectron spectroscopy (XPS) was employed to investigate the surface chemical composition of growth products.

36 MATERIALS SCIENCE↗

Effect of Backbone Chemistry on the Structure of Polyurea Films Deposited by Molecular Layer Deposition

An experimental investigation into the growth of polyurea films by molecular layer deposition was performed by examining trends in the growth rate, crystallinity, and orientation of chains as a function of backbone flexibility. Growth curves obtained for films containing backbones of aliphatic and phenyl groups indicate that an increase in backbone flexibility leads to a reduction in growth rate from 4 to 1 Å/cycle. Crystallinity measurements collected using grazing incidence X-ray diffraction and Fourier transform infrared spectroscopy suggest that some chains form paracrystalline, out-of-plane stacks of polymer segments with packing distances ranging from 4.4 to 3.7 Å depending on the monomer size. Diffraction intensity is largely a function of the homogeneity of the backbone. Near-edge X-ray absorption fine structure measurements for thin and thick samples show an average chain orientation of ~25° relative to the substrate across all samples, suggesting that changes in growth rate are not caused by differences in chain angle but instead may be caused by differences in the frequency of chain terminations. In conclusion, these results suggest a model of molecular layer deposition-based chain growth in which films consist of a mixture of upward growing chains and horizontally aligned layers of paracrystalline polymer segments.

36 MATERIALS SCIENCE↗

Multipoint Observations of Quasiperiodic Emission Intensification and Effects on Energetic Electron Precipitation

The two Van Allen Probes simultaneously recorded a coherently modulated quasiperiodic (QP) emission that persisted for 3 h. The magnetic field pulsation at the locations of the two satellites showed a substantial difference, and their frequencies were close to but did not exactly match the repetition frequency of QP emissions for most of the time, suggesting that those coherent QP emissions probably originated from a common source, which then propagated over a broad area in the magnetosphere. The QP emissions were amplified by local anisotropic electron distributions, and their large-scale amplitudes were modulated by the plasma density. A novel observation of this event is that chorus waves at frequencies above QP emissions exhibit a strong correlation with QP emissions. Those chorus waves intensified when the QP emissions reach their peak frequency. This indicates that embryonic QP emissions may be critical for its own intensification as well as chorus waves under certain circumstances. A Low-Earth-Orbit POES satellite observed enhanced energetic electron precipitation in conjunction with the Van Allen Probes, providing direct evidence that QP emissions precipitate energetic electrons into the atmosphere. Finally, this scenario is quantitatively confirmed by our quasilinear diffusion simulation results.

79 ASTRONOMY AND ASTROPHYSICS↗

High-energy electron emission from metallic nano-tips driven by intense single-cycle terahertz pulses

Electrons ejected from atoms and subsequently driven to high energies in strong laser fields enable techniques from attosecond pulse generation to imaging with rescattered electrons. Analogous processes govern strong-field electron emission from nanostructures, where long wavelength radiation and large local field enhancements hold the promise for producing electrons with substantially higher energies, allowing for higher resolution time-resolved imaging. Here we report on the use of single-cycle terahertz pulses to drive electron emission from unbiased nano-tips. Energies exceeding 5 keV are observed, substantially greater than previously attained at higher drive frequencies. Despite large differences in the magnitude of the respective local fields, we find that the maximum electron energies are only weakly dependent on the tip radius, for 10 nm<R<1,000 nm. As a result, due to the single-cycle nature of the field, the high-energy electron emission is predicted to be confined to a single burst, potentially enabling a variety of applications.

36 MATERIALS SCIENCE↗

Aerosol jet printing of surface acoustic wave microfluidic devices

Abstract The addition of surface acoustic wave (SAW) technologies to microfluidics has greatly advanced lab-on-a-chip applications due to their unique and powerful attributes, including high-precision manipulation, versatility, integrability, biocompatibility, contactless nature, and rapid actuation. However, the development of SAW microfluidic devices is limited by complex and time-consuming micro/nanofabrication techniques and access to cleanroom facilities for multistep photolithography and vacuum-based processing. To simplify the fabrication of SAW microfluidic devices with customizable dimensions and functions, we utilized the additive manufacturing technique of aerosol jet printing. We successfully fabricated customized SAW microfluidic devices of varying materials, including silver nanowires, graphene, and poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS). To characterize and compare the acoustic actuation performance of these aerosol jet printed SAW microfluidic devices with their cleanroom-fabricated counterparts, the wave displacements and resonant frequencies of the different fabricated devices were directly measured through scanning laser Doppler vibrometry. Finally, to exhibit the capability of the aerosol jet printed devices for lab-on-a-chip applications, we successfully conducted acoustic streaming and particle concentration experiments. Overall, we demonstrated a novel solution-based, direct-write, single-step, cleanroom-free additive manufacturing technique to rapidly develop SAW microfluidic devices that shows viability for applications in the fields of biology, chemistry, engineering, and medicine.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Role of Assay Type in Determining Free 25-Hydroxyvitamin D Levels in Diverse Populations

Serum 25-hydroxyvitamin D (25OHD) is the most frequently used marker of vitamin D status. Low 25OHD is associated with bone loss, fractures {Cauley, 2010 #1516;Ensrud, 2009 #1517}, and other adverse health outcomes {Theodoratou, 2014 #1518}. Most extra renal tissues only have access to free 25OHD, and free 25OHD concentration is thus a plausible biomarker of 25OHD availability and function {Johnsen, 2014 #1443;Chun, 2014 #1343}. Stronger associations with free or bioavailable 25OHD than with total 25OHD were reported for serum calcium, parathyroid hormone (PTH) {Bhan, 2012 #1124} and bone mineral density (BMD) {Powe, 2011 #1129}. These findings have led to the suggestion that free or bioavailable 25OHD may provide a more clinically relevant measure of tissue 25OHD availability and vitamin D status {Powe, 2013 #1369; Holick NEJM 2013 editorial}. The US Preventive Services Task Force (LeFevre 2015) recently pointed to the gap in research regarding bioavailable and free 25OHD and noted the possibility that these may be better markers of tissue 25OHD availability. Free 25OHD is conventionally calculated from the concentrations of total 25OHD, vitamin D binding protein (DBP) and albumin, with or without a factor accounting for DBP genotype-specific binding affinities {Bouillon, 1981 #1207;Chun, 2012 #1143; Powe, 2011 #1129;Johnsen, 2014 #1443}. DBP—or Group specific component (GC) {Hirschfeld, 1959 #1468}—polymorphisms (rs4588 and rs7041) give rise to three major polymorphic isoforms of DBP, GC-1F, GC-1S and GC-2, the frequencies of which differ globally, with GC-1F alleles more common in populations of African descent {Kambou, 1986 #1122}. Although DBP is a primary component of free and bioavailable 25OHD calculations, substantial variation in DBP between assays has been noted (Powe suggest to cite here previous publications as in previous version of this Ms). Using DBP measured by a monoclonal antibody Powe et al. {Powe, 2013 #1369} concluded that calculated free 25OHD in African-Americans was equal or higher than in US whites, questioning the implications of low total 25OHD concentrations in African Americans (Holick 2013). This idea gained widespread attention in medical and lay press {LeFevre, 2015 #1598; Bhan, 2014 #1485; Durazo-Arvizu, 2014 #1519}, and many others) and may have important implications for nutrional supplementation policy. To better understand the importance of free 25OHD estimates, and its racial differences, we conducted studies in cohorts based in the US, UK and The Gambia that included participants of African and European ancestry known to differ in GC genotype distribution. We characterized the molecular forms of circulating DBP through comparison of several DBP assays and DBP peptide proteomic analysis, to obtain both calculated and directly measured free 25OHD by geographical region, race and GC genotype.

Environmental Molecular Sciences Laboratory↗

ITER ICRF Antenna Reduced-Scale Mock-up EM Simulations and Comparisons with the Measurements

A reduced-scale mock-up of one ITER ICRF antenna triplet has been recently built, featuring the optimized front-end geometry, an optimized 4-port junction and the implementation of a service stub. Provision is made to adapt the frequency response of the antenna by acting on the 4-port junction arms lengths, the service stub length as well as the position of its inclusion in the circuit. Variable antenna loading is achieved by moving a salted water tank in front of the antenna. A summary of the first measurements carried out on this mockup is reported in a companion paper. The EM simulations of the mock-up are done with CST Microwave Studio registered. The geometry of the mock-up is converted from a CAD file and all essential details are included in the model. S parameters of the mock-up are calculated in a large frequency range covering the ITER ICRF antenna frequency band for different geometries of the mock-up and distances to the load. Results of the simulations and systematic comparisons with the measurements are presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Influence of inhomogeneous magnetic field on the characteristics of very high frequency capacitively coupled plasmas

The effect of inhomogeneous magnetic field on the spatial structure of very high frequency (VHF) plasmas is investigated for different coil configurations, gas pressures, high frequency bias powers, and degrees of electronegativity. The simulation results show that the electron density peaks in the center of the chamber for VHF plasmas due to the standing electromagnetic wave effect. On application of a magnetic field, the density increases near the wafer edge and decreases at the chamber center. The radial magnetic field component is found to limit electron loss to the electrodes and locally enhance the electron density. The axial magnetic field component limits plasma diffusion in the radial direction helping preserve the effect of improved electron confinement by the radial magnetic field. The peak electron density decreases with increasing magnetic field as the plasma moves toward the electrode edge occupying a larger volume. The effect of magnetic field becomes weaker at higher pressure due to the increased electron-neutral collisions which reduce the effectiveness of electron confinement around the magnetic field lines. The impact of magnetic field on plasma profile is somewhat weaker in an electronegative Ar/CF{sub 4} plasma because of the presence of less mobile and unmagnetized negative ions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Three-dimensional structure of electron density fluctuations in the Hall thruster plasma: ExB mode

Collective scattering measurements have been conducted on the plasma of a Hall thruster, in which the electron density fluctuations are fully characterized by the dynamic form factor. The dynamic form factor amplitude distribution has been measured depending on the k-vector spatial and frequency components at different locations. Fluctuations are seen as propagating waves. The largest amplitude mode propagates nearly along the cross-field direction but at a phase velocity that is much smaller than the ExB drift velocity. Refined directional analysis of this largest amplitude mode shows a thin angular emission diagram with a mean direction that is not strictly along the ExB direction but at small angles near it. The deviation is oriented toward the anode in the (E,ExB) plane and toward the exterior of the thruster channel in the (B,ExB) plane. The density fluctuation rate is on the order of 1%. These experimentally determined directional fluctuation characteristics are discussed with regard to the linear kinetic theory model and particle-in-cell simulation results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Influence of viscoelastic property on laser-generated surface acoustic waves in coating-substrate systems

Taking account of the viscoelasticity of materials, the pulsed laser generation of surface acoustic waves in coating-substrate systems has been investigated quantitatively by using the finite element method. The displacement spectra of the surface acoustic waves have been calculated in frequency domain for different coating-substrate systems, in which the viscoelastic properties of the coatings and substrates are considered separately. Meanwhile, the temporal displacement waveforms have been obtained by applying inverse fast Fourier transforms. The numerical results of the normal surface displacements are presented for different configurations: a single plate, a slow coating on a fast substrate, and a fast coating on a slow substrate. The influences of the viscoelastic properties of the coating and the substrate on the attenuation of the surface acoustic waves have been studied. In addition, the influence of the coating thickness on the attenuation of the surface acoustic waves has been also investigated in detail.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Ultrasonic characterization of interfaces in composite bonds

The inverse determination of imperfect interfaces from reflection spectra of normal and oblique incident ultrasonic waves in adhesive bonds of multidirectional composites is investigated. The oblique measurements are complicated by the highly dispersed nature of oblique wave spectra at frequencies above 3MHz. Different strategies for bond property reconstruction, including a modulation method, are discussed. The relation of measured interfacial spring density to the physico-chemical model of a composite interface described by polymer molecular bonds to emulate loss of molecular strength on an adhesive composite interface is discussed. This potentially relates the interfacial (adhesion) strength (number of bonds at the adhesive substrate interface) to the spring constant (stiffness) area density (flux), which is an ultrasonically measurable parameter.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

X-ray spectroscopy of warm and hot electron components in the CAPRICE source plasma at EIS testbench at GSI

An experimental campaign aiming to detect X radiation emitted by the plasma of the CAPRICE source – operating at GSI, Darmstadt – has been carried out. Two different detectors (a SDD – Silicon Drift Detector and a HpGe – hyper-pure Germanium detector) have been used to characterize the warm (2–30 keV) and hot (30–500 keV) electrons in the plasma, collecting the emission intensity and the energy spectra for different pumping wave frequencies and then correlating them with the CSD of the extracted beam measured by means of a bending magnet. A plasma emissivity model has been used to extract the plasma density along the cone of sight of the SDD and HpGe detectors, which have been placed beyond specific collimators developed on purpose. Results show that the tuning of the pumping frequency considerably modifies the plasma density especially in the warm electron population domain, which is the component responsible for ionization processes: a strong variation of the plasma density near axis region has been detected. Potential correlations with the charge state distribution in the plasma are explored.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Pressure distribution based optimization of phase-coded acoustical vortices

Based on the acoustic radiation of point source, the physical mechanism of phase-coded acoustical vortices is investigated with formulae derivations of acoustic pressure and vibration velocity. Various factors that affect the optimization of acoustical vortices are analyzed. Numerical simulations of the axial, radial, and circular pressure distributions are performed with different source numbers, frequencies, and axial distances. The results prove that the acoustic pressure of acoustical vortices is linearly proportional to the source number, and lower fluctuations of circular pressure distributions can be produced for more sources. With the increase of source frequency, the acoustic pressure of acoustical vortices increases accordingly with decreased vortex radius. Meanwhile, increased vortex radius with reduced acoustic pressure is also achieved for longer axial distance. With the 6-source experimental system, circular and radial pressure distributions at various frequencies and axial distances have been measured, which have good agreements with the results of numerical simulations. The favorable results of acoustic pressure distributions provide theoretical basis for further studies of acoustical vortices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Enhanced localized energetic ion losses resulting from first-orbit linear and non-linear interactions with Alfvén eigenmodes in DIII-D

Two key insights into interactions between Alfvén eigenmodes (AEs) and energetic particles in the plasma core are gained from measurements and modeling of first-orbit beam-ion loss in DIII-D. First, the neutral beam-ion first-orbit losses are enhanced by AEs and a single AE can cause large fast-ion displacement. The coherent losses are from born trapped full energy beam-ions being non-resonantly scattered by AEs onto loss orbits within their first poloidal transit. The loss amplitudes scale linearly with the mode amplitude but the slope is different for different modes. The radial displacement of fast-ions by individual AEs can be directly inferred from the measurements. Second, oscillations in the beam-ion first-orbit losses are observed at the sum, difference, and harmonic frequencies of two independent AEs. These oscillations are not plasma modes and are absent in magnetic, density, and temperature fluctuations. The origin of the non-linearity as a wave-particle coupling is confirmed through bi-coherence analysis, which is clearly observed because the coherences are preserved by the first-orbit loss mechanism. An analytic model and full orbit simulations show that the non-linear features seen in the loss signal can be explained by a non-linear interaction between the fast ions and the two independent AEs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Dark current mechanism of terahertz quantum-well photodetectors

Dark current mechanisms of terahertz quantum-well photodetectors (THz QWPs) are systematically investigated experimentally and theoretically by measuring two newly designed structures combined with samples reported previously. In contrast to previous investigations, scattering-assisted tunneling dark current is found to cause significant contributions to total dark current. A criterion is also proposed to determine the major dark current mechanism at different peak response frequencies. We further determine background limited performance (BLIP) temperatures, which decrease both experimentally and theoretically as the electric field increases. This work gives good description of dark current mechanism for QWPs in the THz region and is extended to determine the transition fields and BLIP temperatures with response peaks from 3 to 12 THz.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Explicit approximations to estimate the perturbative diffusivity in the presence of convectivity and damping. I. Semi-infinite slab approximations

In this paper, a number of new approximations are introduced to estimate the perturbative diffusivity (χ), convectivity (V), and damping (τ) in cylindrical geometry. For this purpose, the harmonic components of heat waves induced by localized deposition of modulated power are used. The approximations are based on semi-infinite slab approximations of the heat equation. The main result is the approximation of χ under the influence of V and τ based on the phase of two harmonics making the estimate less sensitive to calibration errors. To understand why the slab approximations can estimate χ well in cylindrical geometry, the relationships between heat transport models in slab and cylindrical geometry are studied. In addition, the relationship between amplitude and phase with respect to their derivatives, used to estimate χ, is discussed. The results are presented in terms of the relative error for the different derived approximations for different values of frequency, transport coefficients, and dimensionless radius. The approximations show a significant region in which χ, V, and τ can be estimated well, but also regions in which the error is large. Also, it is shown that some compensation is necessary to estimate V and τ in a cylindrical geometry. On the other hand, errors resulting from the simplified assumptions are also discussed showing that estimating realistic values for V and τ based on infinite domains will be difficult in practice. This paper is the first part (Part I) of a series of three papers. In Part II and Part III, cylindrical approximations based directly on semi-infinite cylindrical domain (outward propagating heat pulses) and inward propagating heat pulses in a cylindrical domain, respectively, will be treated.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Investigation and quantification of nonlinearity using surrogate data in a glow discharge plasma

Detection of nonlinearity has been carried out in periodic and aperiodic floating potential fluctuations of DC glow discharge plasma by generating surrogate data using iterative amplitude adjusted Fourier transform method. We introduce “delay vector variance” analysis (DVV) for the first time, which allows reliable detection of nonlinearity and provides some easy to interpret diagram conveying information about the nature of the experimental floating potential fluctuations (FPF). The method of false nearest neighbourhood is deployed on the FPF's to find a good embedding so as to be acquainted with the precise knowledge of m, which is desirable for carrying out DVV analysis. The emergence of nonlinearity with increase in discharge voltage has been ensured by taking into consideration the total energy present in different band of frequencies excited due to nonlinear processes. Rejection of null hypothesis has been verified by performing the rank test method that confirms the presence of nonlinearity quantitatively.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effects of nitrogen plasma treatment on the electrical property and band structure of few-layer MoS{sub 2}

Few-layer MoS{sub 2} prepared by the chemical vapor deposition method was treated with nitrogen plasma under different radio-frequency (rf) power conditions in order to experimentally study the change in the electrical property. Control of the rf power could change the work function of MoS{sub 2} from 5.40 eV to 5.06 eV. It is shown that the increased rf power leads to the increased (reduced) number of nitrogen (oxygen) atoms, increasing the electron concentration and shifting the Fermi level toward conduction band. The sensitivity of the work function to the rf power provides an opportunity to tune the work function of MoS{sub 2}.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗