Search NASA⌕ Search

SEARCH · Search NASA

Results for “etching”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Meter-scale High-temperature Superconducting RF Waveguides with Integrated Filters and Attenuators

Here, we report the performance of coplanar, multifilament waveguides manufactured from crystalline films of a well-known HTS compound, YBCO, transferred to a low-loss dielectric substrate, such as E-Kapton. The coplanar two-line waveguide delivers low cross-talk, below 20 dB level, and low attenuation, below 4 dB/m at 6 GHz, 77 K. Controlled-impedance 50 Ω waveguides would require a method for reliable patterning narrow, less than 100-micron wide, YBCO traces over a meter length. We report a lithography-etching approach that minimizes the difference in the etching rate of YBCO and the metallization layers of Ag and Cu. An array of metalized vias isolates the traces. We describe the via metallization process that is not damaging to YBCO and compatible with dense, 2 mm period, arrays of vias.

36 MATERIALS SCIENCE↗

Aluminum-Based Superconducting Tunnel Junction Sensors for Nuclear Recoil Spectroscopy

The BeEST experiment is searching for sub-MeV sterile neutrinos by measuring nuclear recoil energies from the decay of 7 Be implanted into superconducting tunnel junction (STJ) sensors. The recoil spectra are affected by interactions between the radioactive implants and the sensor materials. We are therefore developing aluminum-based STJs (Al-STJs) as an alternative to existing tantalum devices (Ta-STJs) to investigate how to separate material effects in the recoil spectrum from potential signatures of physics beyond the Standard Model. Three iterations of Al-STJs were fabricated. The first had electrode thicknesses similar to existing Ta-STJs. They had low responsivity and reduced resolution, but were used successfully to measure 7 Be nuclear recoil spectra. The second iteration had STJs suspended on thin SiN membranes by backside etching. These devices had low leakage current, but also low yield. The final iteration was not backside etched, and the Al-STJs had thinner electrodes and thinner tunnel barriers to increase signal amplitudes. These devices achieved 2.96 eV FWHM energy resolution at 50 eV using a pulsed 355 nm (~3.5 eV) laser. These results establish Al-STJs as viable detectors for systematic material studies in the BeEST experiment.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Temperature-Agnostic Pt/Au Ohmic Contacts on n -Type Gallium Nitride for Self-Aligned MOSFETs

Five alternative metals are investigated as ohmic contacts to n-GaN including Cr/Au, Mo/Au, Pt/Au, Pd/Au, and Ge/Au. Ti-based contacts are traditionally used for ohmic contacts on n-GaN. However, conventional Ti/Al/Ni/Au metallization is found to be incompatible with a self-aligned process for GaN trench MOSFETs due to wet etch restrictions. Therefore, an alternative metallization is needed that is unreactive to the etch chemistry used in the self-aligned process. Additionally, the contact should remain ohmic following anneal at 900 °C so that contact formation can precede the anneal required for p-dopant activation. Here, in the present work, an n-GaN bilayer, consisting of a thin heavily doped contact layer (n 0 = 1 × 10 20 cm −3 ) atop a thick lesser doped layer, is used to demonstrate ohmic contacts of alternative metals with low specific contact resistance and extended thermal budget. Cr/Au ohmic contacts are demonstrated up to anneal temperatures of 800 °C, an increase of 200 °C compared to the highest known reports for Cr/Au contacts on n-GaN. Pt/Au metallization is demonstrated as an ohmic contact to n-GaN for the first time and exhibits true temperature-agnostic behavior up to anneal temperatures of 900 °C with specific contact resistance that is near parity with Ti/Al/Ni/Au. The temperature-agnostic behavior of Pt/Au ohmic contacts on the n-GaN bilayer, in addition to chemical compatibility with the self-aligned process, positions Pt/Au contacts as a key enabling element for self-aligned trench MOSFETs on GaN.

Reilly, Kevin James [Sandia National Laboratories ↗

Chemistry in long residence time fluorocarbon plasmas

The densities of radicals and neutrals in fluorocarbon (FC) plasmas have been investigated in an inductively coupled plasma system to understand the predominant gain and loss mechanisms of dissociative products and their interaction with chamber surfaces. The input parameters varied in this experiment are the source to chuck gap and the F: C ratio of the feed gas. The densities of F, CF{sub 2}, CF{sub 3}, CF{sub 4}, C{sub 2}F{sub 4}, SiF{sub 4}, COF{sub 2}, CO, and CO{sub 2} are measured and analyzed. In addition, two different forms of C{sub 4}F{sub 8}, the standard cyclic c and a radical linear l structures are observed in C{sub 4}F{sub 8} containing plasmas. l-C{sub 4}F{sub 8} is shown to be the primary dissociation product of c-C{sub 4}F{sub 8} and, thus, cannot be neglected from calculations of the loss rate of c-C{sub 4}F{sub 8} to electron collisions. This implies that the typically cited dissociative products of c-C{sub 4}F{sub 8} (primarily C{sub 2}F{sub 4}) can have dual production channels: one from l-C{sub 4}F{sub 8} and the other directly from c-C{sub 4}F{sub 8}. Furthermore, the measured density of CF{sub 4} shows strong correlation to the loss of F to the surfaces, indicating its primary production mechanism is from surface recombination. Similarly, CF{sub 3} is mainly produced from deposited FC film on chamber surfaces and lost to electron impact reactions. The etch products resulting from etch of the quartz window are shown, and an overall neutral density model is developed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Role of plasma enhanced atomic layer deposition reactor wall conditions on radical and ion substrate fluxes

Chamber wall conditions, such as wall temperature and film deposits, have long been known to influence plasma source performance on thin film processing equipment. Plasma physical characteristics depend on conductive/insulating properties of chamber walls. Radical fluxes depend on plasma characteristics as well as wall recombination rates, which can be wall material and temperature dependent. Variations in substrate delivery of plasma generated species (radicals, ions, etc.) impact the resulting etch or deposition process resulting in process drift. Plasma enhanced atomic layer deposition is known to depend strongly on substrate radical flux, but film properties can be influenced by other plasma generated phenomena, such as ion bombardment. In this paper, the chamber wall conditions on a plasma enhanced atomic layer deposition process are investigated. The downstream oxygen radical and ion fluxes from an inductively coupled plasma source are indirectly monitored in temperature controlled (25–190 °C) stainless steel and quartz reactors over a range of oxygen flow rates. Etch rates of a photoresist coated quartz crystal microbalance are used to study the oxygen radical flux dependence on reactor characteristics. Plasma density estimates from Langmuir probe ion saturation current measurements are used to study the ion flux dependence on reactor characteristics. Reactor temperature was not found to impact radical and ion fluxes substantially. Radical and ion fluxes were higher for quartz walls compared to stainless steel walls over all oxygen flow rates considered. The radical flux to ion flux ratio is likely to be a critical parameter for the deposition of consistent film properties. Reactor wall material, gas flow rate/pressure, and distance from the plasma source all impact the radical to ion flux ratio. These results indicate maintaining chamber wall conditions will be important for delivering consistent results from plasma enhanced atomic layer deposition systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Atomic layer deposited lithium aluminum oxide: (In)dependency of film properties from pulsing sequence

Atomic layer deposition (ALD) holds markedly high potential of becoming the enabling method for achieving the three-dimensional all-solid-state thin-film lithium ion battery (LiB). One of the most crucial components in such a battery is the electrolyte that needs to hold both low electronic conductivity and at least fair lithium ion conductivity being at the same time pinhole free. To obtain these desired properties in an electrolyte film, one necessarily has to have a good control over the elemental composition of the deposited material. The present study reports on the properties of ALD lithium aluminum oxide (Li{sub x}Al{sub y}O{sub z}) thin films. In addition to LiB electrolyte applications, Li{sub x}Al{sub y}O{sub z} is also a candidate low dielectric constant (low-k) etch stop and diffusion barrier material in nanoelectronics applications. The Li{sub x}Al{sub y}O{sub z} films were deposited employing trimethylaluminum-O{sub 3} and lithium tert-butoxide-H{sub 2}O for Al{sub 2}O{sub 3} and Li{sub 2}O/LiOH, respectively. The composition was aimed to be controlled by varying the pulsing ratio of those two binary oxide ALD cycles. The films were characterized by several methods for composition, crystallinity and phase, electrical properties, hardness, porosity, and chemical environment. Regardless of the applied pulsing ratio of Al{sub 2}O{sub 3} and Li{sub 2}O/LiOH, all the studied ALD Li{sub x}Al{sub y}O{sub z} films of 200 and 400 nm in thickness were polycrystalline in the orthorhombic β-LiAlO{sub 2} phase and also very similar to each other with respect to composition and other studied properties. The results are discussed in the context of both fundamental ALD chemistry and applicability of the films as thin-film LiB electrolytes and low-k etch stop and diffusion barriers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Design and Fabrication of Ta filled microcavites in the delay paths of SAW devices for improved power transfer

The authors report the design and fabrication of a surface acoustic wave (SAW) device with improved power transfer due to modification of its delay path. Typically, SAW delay-line devices suffer from relatively high insertion loss (IL) (similar to 10-30 dB). Our approach is to incorporate an array of microcavities, having square cross-sectional area (lambda/2 x lambda/2) and filled with tantalum, within the delay path to maximize acoustic confinement to the surface and reduce IL. To determine the effectiveness of the cavities without expending too many resources and to explain trends found in actual devices, a finite element model of a SAW device with tantalum filled cavities having various depths was utilized. For each depth simulated, IL was decreased compared to a standard SAW device. Microcavities 2.5 mu m deep filled with tantalum showed the best performance (Delta IL = 17.93 dB). To validate simulated results, the authors fabricated a SAW device on ST 90 degrees-X quartz with microcavities etched into its delay path using deep reactive ion etching and filled with tantalum. Measurement of fabricated devices showed inclusion of tantalum filled microcavities increased power transfer compared to a device without cavities. (C) 2015 American Vacuum Society.

Richardson, Mandek↗

Study on spatial distribution of plasma parameters in a magnetized inductively coupled plasma

Spatial distributions of various plasma parameters such as plasma density, electron temperature, and radical density in an inductively coupled plasma (ICP) and a magnetized inductively coupled plasma (M-ICP) were investigated and compared. Electron temperature in between the rf window and the substrate holder of M-ICP was higher than that of ICP, whereas the one just above the substrate holder of M-ICP was similar to that of ICP when a weak (<8 G) magnetic field was employed. As a result, radical densities in M-ICP were higher than those in ICP and the etch rate of oxide in M-ICP was faster than that in ICP without severe electron charging in 90 nm high aspect ratio contact hole etch.

36 MATERIALS SCIENCE↗

Direct fabrication of high aspect-ratio metal oxide nanopatterns via sequential infiltration synthesis in lithographically defined SU-8 templates

Nanopatterning high aspect-ratio metal oxide structures remains challenging for conventional nanofabrication methods based on reactive ion etching due to marginal etch selectivity between target oxides and typical mask materials. Here, the authors report the application of sequential infiltration synthesis (SIS) on lithographically defined SU-8 polymer templates for patterning arbitrarily designed, high aspect-ratio metal oxide nanostructures with sub-50 nm linewidths, smooth vertical profiles, and three-dimensional (3D) morphologies difficult to achieve by the conventional fabrication methods. As examples, various AlOx nanostructures with ∼40 nm linewidths and up to 16 aspect ratios were demonstrated, along with TiOx in-plane nanowire arrays of controlled positional registrations. Detailed scanning and transmission electron microscopy studies revealed nanocrystalline and amorphous internal structures of respective AlOx and TiOx, as well as the swelling and contraction behaviors of polymer templates during the SIS process, which allowed the facile fabrication of high aspect-ratio, sub-50 nm-featured oxide nanopatterns with 3D morphologies. These results confirm the potential of vapor-phase material infiltration in directly nanopatterning complexly structured metal oxides.

Nam, Chang-Yong↗

Effect of GaN surface treatment on Al 2 O 3 /n-GaN MOS capacitors

The surface preparation for depositing Al 2 O 3 for fabricating Au/Ni/Al 2 O 3 /n-GaN (0001) metal oxide semiconductor (MOS) capacitors was optimized as a step toward realization of high performance GaN MOSFETs. The GaN surface treatments studied included cleaning with piranha (H 2 O 2 :H 2 SO 4 = 1:5), (NH 4 )(2)S, and 30% HF etches. By several metrics, the MOS capacitor with the piranha-etched GaN had the best characteristics. It had the lowest capacitance-voltage hysteresis, the smoothest Al 2 O 3 surface as determined by atomic force microscopy (0.2nm surface roughness), the lowest carbon concentration (similar to 0.78%) at the Al 2 O 3 /n-GaN interface (from x-ray photoelectron spectroscopy), and the lowest oxide-trap charge (Q(T) = 1.6 x 10(11) cm(-2) eV(-1)). Its interface trap density (D-it = 3.7 x 10(12) cm(-2) eV(-1)), as measured with photon-assisted capacitance- voltage method, was the lowest from conduction band-edge to midgap. (C) 2015 American Vacuum Society.

36 MATERIALS SCIENCE↗

Plasma enhanced atomic layer deposition of silicon nitride using neopentasilane

Progress in transistor scaling has increased the demands on the material properties of silicon nitride (SiN{sub x}) thin films used in device fabrication and at the same time placed stringent restrictions on the deposition conditions employed. Recently, low temperature plasma enhanced atomic layer deposition has emerged as a viable technique for depositing these films with a thermal budget compatible with semiconductor processing at sub-32 nm technology nodes. For these depositions, it is desirable to use precursors that are free from carbon and halogens that can incorporate into the film. Beyond this, it is necessary to develop processing schemes that minimize the wet etch rate of the film as it will be subjected to wet chemical processing in subsequent fabrication steps. In this work, the authors introduce low temperature deposition of SiN{sub x} using neopentasilane [NPS, (SiH{sub 3}){sub 4}Si] in a plasma enhanced atomic layer deposition process with a direct N{sub 2} plasma. The growth with NPS is compared to a more common precursor, trisilylamine [TSA, (SiH{sub 3}){sub 3 }N] at identical process conditions. The wet etch rates of the films deposited with NPS are characterized at different plasma conditions and the impact of ion energy is discussed.

36 MATERIALS SCIENCE↗

Native oxide transport and removal during the atomic layer deposition of Ta{sub 2}O{sub 5} on InAs(100) surfaces

Atomic layer deposition (ALD) was used to deposit Ta{sub 2}O{sub 5} on etched and native oxide-covered InAs(100) using pentakis dimethyl amino tantalum and H{sub 2}O at 200–300 °C. The transport and removal of the native oxides during the ALD process was investigated using x-ray photoelectron spectroscopy (XPS). Depositions above 200 °C on etched surfaces protected the interface from reoxidation. On native oxide-covered surfaces, depositions resulted in enhanced native oxide removal at higher temperatures. The arsenic oxides were completely removed above 250 °C after 3 nm of film growth, but some of the As{sub 2}O{sub 3} remained in the film at lower temperatures. Angle-resolved and sputter depth profiling XPS confirmed indium and arsenic oxide migration into the Ta{sub 2}O{sub 5} film at deposition temperatures as low as 200 °C. Continuous removal of both arsenic and indium oxides was confirmed even after the deposition of several monolayers of a coalesced Ta{sub 2}O{sub 5} film, and it was demonstrated that native oxide transport is a prevalent component of the interface “clean-up” mechanism.

36 MATERIALS SCIENCE↗

Monte Carlo simulations of secondary electron emission due to ion beam milling

We present a Monte Carlo simulation study of secondary electron emission resulting from focused ion beam milling of a copper target. The basis of this study is a simulation code which simulates ion induced excitation and emission of secondary electrons, in addition to simulating focused ion beam sputtering and milling. This combination of features permits the simulation of the interaction between secondary electron emission, and the evolving target geometry as the ion beam sputters material. Previous ion induced SE Monte Carlo simulation methods have been restricted to predefined target geometries, while the dynamic target in the presented simulations makes this study relevant to image formation in ion microscopy, and chemically assisted ion beam etching, where the relationship between sputtering, and its effects on secondary electron emission, is important. We focus on a copper target, and validate our simulation against experimental data for a range of: noble gas ions, ion energies, ion/substrate angles and the energy distribution of the secondary electrons. We then provide a detailed account of the emission of secondary electrons resulting from ion beam milling; we quantify both the evolution of the yield as high aspect ratio valleys are milled, as well as the emission of electrons within these valleys that do not escape the target, but which are important to the secondary electron contribution to chemically assisted ion induced etching.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Maskless random antireflective nanotexturing of single crystal SiC

Random nanotexturing of optics and semiconductors has proven to be a highly effective way to produce high transmittivity, low reflective surfaces. Here, the authors report a one-step technique using SF6 reactive ion etching to produce nanotexturing of SiC. The effect of etching process power and time is optimized to demonstrate sub-1% specular reflectance and below 5% total reflectance over the 400–2000 nm spectral range. The technique is applied to compare measurements of a photoconductive switch with untreated and treated surfaces. In conclusion, using a white light source emitting in the range 400–750 nm, the authors show that the decrease in specular reflectivity results in a 20% increase in the photocurrent response.

36 MATERIALS SCIENCE↗

Continuous polymer films deposited on top of porous substrates using plasma-enhanced atomic layer deposition and molecular layer deposition

Molecular layer deposition (MLD) is able to produce ultrathin polymer films with control over thickness, cross-linking, and chemical composition. With these capabilities, MLD should be useful in the fabrication of novel polymer membranes on porous supports. However, confining a continuous MLD film to the surface of porous substrates is difficult because of MLD film growth in the pores. The deposition in the pores lowers the conductance of the porous support. This paper presents a method to deposit continuous polymer films on top of porous substrates. In this method, Al2O3 plasma-enhanced atomic layer deposition (PE-ALD) using trimethylaluminum and oxygen plasma as the reactants was first used to cap the pores of the substrate. Subsequently, a polyamide MLD film was deposited on the Al2O3 PE-ALD capping layer using m-phenylenediamine and trimesoyl chloride as the reactants. The Al2O3 pore caps were then removed from the porous substrate by etching from the backside using a timed exposure to a dilute sodium hydroxide solution. This method was demonstrated using anodic aluminum oxide (AAO) and polyethersulfone (PES) porous substrates. Al2O3 PE-ALD film growth was limited to the top of the porous substrate, resulting in rapid surface recombination or high sticking coefficients for the reactive plasma species within the pores. Gas permeance measurements confirmed the pore capping of the AAO substrates. The reopening of the pores by dissolving the Al2O3 pore caps with a sodium hydroxide solution was monitored using gas permeance versus etch time. The removal of the Al2O3 pore caps from the PES substrates could also dissolve the Al2O3 layer underneath the MLD film. The loss of this Al2O3 layer led to the detachment of the MLD film from the PES substrate. However, the MLD film could be anchored to the PES support at fractures located in the Al2O3 film prior to the MLD. The Al2O3 film fracture allowed the MLD film to anchor firmly to the PES substrate by MLD in the pores of the PES porous substrate. The distance between the anchor points was a function of fracture density. This distance could be controlled by applying a tensile stress to the Al2O3 PE-ALD film to fracture the film through sample bending. This method produced firmly anchored polymer MLD films on top of the PES porous substrates.

Welch, Brian C. (ORCID:000000029747045X)↗

Multiresonant layered plasmonic films

Multi-resonant nanoplasmonic films have numerous applications in areas such as nonlinear optics, sensing, and tamper indication. While techniques such as focused ion beam milling and electron beam lithography can produce high-quality multi-resonant films, these techniques are expensive, serial processes that are difficult to scale at the manufacturing level. Here, we present the fabrication of multi-resonant nanoplasmonic films using a layered stacking technique. Periodically-spaced gold nanocup substrates were fabricated using self-assembled polystyrene nanospheres followed by oxygen plasma etching and metal deposition via magnetron sputter coating. By adjusting etch parameters and initial nanosphere size, it was possible to achieve an optical response ranging from the visible to the near-infrared. Singly resonant, flexible films were first made by performing peel-off using an adhesive-coated polyolefin film. Through stacking layers of the nanofilm, we demonstrate fabrication of multi-resonant films at a fraction of the cost and effort as compared to top-down lithographic techniques.

nano↗

Strain-free polished channel-cut crystal monochromators: a new approach and results

The use of channel-cut crystal monochromators has been traditionally limited to applications that can tolerate the rough surface quality from wet etching without polishing. We have previously presented and discussed the motivation for producing channel cut crystals with strain-free polished surfaces [1]. Afterwards, we have undertaken an effort to design and implement an automated machine for polishing channel-cut crystals. The initial effort led to inefficient results. Since then, we conceptualized, designed, and implemented a new version of the channel-cut polishing machine, now called C-CHiRP (Channel-Cut High Resolution Polisher), also known as CCPM V2.0. The new machine design no longer utilizes Figure-8 motion that mimics manual polishing. Instead, the polishing is achieved by a combination of rotary and linear functions of two coordinated motion systems. Here we present the new design of C-CHiRP, its capabilities and features. Multiple channel-cut crystals polished using the C-CHiRP have been deployed into several beamlines at the Advanced Photon Source (APS). We present the measurements of surface finish, flatness, as well as topography results obtained at 1-BM of APS, as compared with results typically achieved when polishing flat-surface monochromator crystals using conventional polishing processes. Limitations of the current machine design, capabilities and considerations for strain-free polishing of highly complex crystals are also discussed, together with an outlook for future developments and improvements.

Kasman, Elina↗

Frequency selective bolometer development at Argonne National Laboratory.

We discuss the development, at Argonne National Laboratory, of a four-pixel camera suitable for photometry of distant dusty galaxies located by Spitzer and SCUBA, and for study of other millimeter-wave sources such as ultra-luminous infrared galaxies, the Sunyaev-Zeldovich (SZ) effect in clusters, and galactic dust. Utilizing Frequency Selective Bolometers (FSBs) with superconducting Transition-Edge Sensors (TESs), each of the camera's four pixels is sensitive to four colors, with frequency bands centered approximately at 150, 220, 270, and 360 GHz. The current generation of these devices utilizes proximity effect superconducting bilayers of Mo/Au or Ti/Au for TESs, along with frequency selective circuitry on membranes of silicon nitride 1 cm across and 1 micron thick. The operational properties of these devices are determined by this circuitry, along with thermal control structures etched into the membranes. These etched structures do not perforate the membrane, so that the device is both comparatively robust mechanically and carefully tailored in terms of its thermal transport properties. In this paper, we report on development of the superconducting bilayer TES technology and characterization of the FSB stacks. This includes the use of new materials, the design and testing of thermal control structures, the introduction of desirable thermal properties using buried layers of crystalline silicon underneath the membrane, detector stability control, and optical and thermal test results. The scientific motivation, FSB design, FSB fabrication, and measurement results are discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗