Search NASA⌕ Search

SEARCH · Search NASA

Results for “experimental data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Heat Pump Clothes Dryer Model Development

A heat pump clothes dryer (HPCD) is an innovative appliance that uses a vapor compression system to dry clothes. Air circulates in a closed loop through the drum, so no vent is required. The condenser heats air to evaporate moisture out of the clothes, and the evaporator condenses water out of the air stream. As a result, the HPCD can achieve 50% energy savings compared to a conventional electric resistance dryer. We developed a physics-based, quasi-steady-state HPCD system model with detailed heat exchanger and compressor models. In a novel approach, we applied a heat and mass transfer effectiveness model to simulate the drying process of the clothes load in the drum. The system model is able to simulate the inherently transient HPCD drying process, to size components, and to reveal trends in key variables (e.g. compressor discharge temperature, power consumption, required drying time, etc.) The system model was calibrated using experimental data on a prototype HPCD. In the paper, the modeling method is introduced, and the model predictions are compared with experimental data measured on a prototype HPCD.

Heat Pump Clothes Dryer↗

Analysis on the Preliminary Gap Conductance Test with Single Primary Heat Extraction and Removal Emulator

Microreactor is a type of nuclear reactor that is intended to produce thermal energy from the micro and integrated design. Among various microreactor roadmaps, microreactor with heat pipes is one of the promising designs that under active development. At Idaho National Laboratory (INL) and supported by the Department of Energy (DOE) Microreactor Program (MRP), a Single Primary Heat Extraction and Removal Emulator (SPHERE) was developed. The main purpose of SPHRE is to understand thermal performance of heat pipe in the conjunction of heat source without using nuclear material. The heat pipe used in the SPHERE has sodium as a working fluid, with Argon gas in the vapor region, thus this heat pipe is variable conductance heat pipe (VCHP). The volume of non-condensable gas changes with power and elapsed time, so the area covered by non-condensable gas changes. This gives an effect that passively controls the cooling capability of condenser section. This preliminary experiment was intended to perform a gap conductance experiment that reveals heat transfer characteristics of gas at the gap around the heat pipe. However, there are not many experimental data that deals with heat transfer of the gas at the gap around heat pipe. In this research, the preliminary experimental result regarding to the heat pipe performance with different composition of gas at the gap, level of power is presented. The experimental data will be used for the validation study of SOCKEYE as a future plan.

42 ENGINEERING↗

Multiscale Modeling of Thermoplastics Using Atomistic-informed Micromechanics

A multiscale model was developed for predicting the thermoelastic behavior of semi-crystalline thermoplastic materials for composite aerospace applications. At the highest scale containing the semi-crystalline spherulite in an amorphous matrix, the generalized method of cells, or high fidelity method of cells, was used to perform the homogenization calculations to obtain the effective properties. Models were developed assuming a cubic, or spherical shape, for the spherulite to understand if the morphology of the spherulite affects the effective thermoelastic properties. The generalized method of cells was used to model at the repeating unit cells at the subscales of the microstructure including the lamellae stacks and granular crystal blocks. The scales are integrated using the multiscale micromechanics method in the NASA Multiscale Analysis Tool. Data from molecular dynamics simulations were used as inputs for the amorphous and crystalline constituents. Convergence studies were performed to determine the best level of discretization for the repeating unit cell at the highest scale. Effective Young’s modulus, shear modulus, Poisson’s ratio, coefficient of thermal expansion, and thermal conductivity were predicted for polyether ether ketone and polyether ketone ketone, and very good agreement between the model utilizing the cubic spherulite and the experimental data, where available, was observed for polyether ketone ketone. Normalization of the data for the bulk polyether ketone ketone, against amorphous data, improved the predictions as compared to experimental data. Overall, the high fidelity method of cells predicted a stiffer response then the generalized method of cells as the crystallinity was increased. The shape of the spherulite had a minimal effect on the predicted bulk properties of the polymers.

thermoplastics↗

Model for determining rupture area in Zircaloy cladding under LOCA conditions

The dispersal of nuclear fuel through a cladding rupture opening during a transient event is the primary safety concern preventing the United States nuclear industry from extending burnup beyond a peak rod average burnup of 62 GWd/tU. The majority of research thus far has prioritized understanding, or at a minimum prioritized quantifying, fuel fragmentation and pulverization as a function of burnup and to a lesser extent onset temperature. Early high burnup loss-of-coolant accident tests performed at the Halden Boiling Water Reactor evaluated the impact of relocation on cladding temperature, whereas historical and recent cladding burst tests focused primarily on generating data related to cladding balloon and burst timing. However, very little effort has been put forth to develop a relationship for determining the rupture opening dimensions for Zircaloy cladding tubes bursting during a simulated light water reactor loss-of-coolant accident. This is significant because high burnup loss-of-coolant accident data suggest dispersal could be limited by the size of the rupture opening or rupture dimensions, thereby minimizing the safety concern. Therefore, the purpose of this research is to build a database composed of all simulated loss-of-coolant accident data to develop an empirical model that conservatively captures the rupture opening dimensions and translates those dimensions to rupture area. Analysis of the experimental data indicates the rupture dimensions are strongly correlated to the peak balloon strain. This relationship is leveraged to develop a rupture length empirical correlation as a function of peak balloon strain and a rupture width empirical correlation as a function of rupture length. Outliers in the experimental data are identified and discussed. Finally, the rupture opening empirical model is presented in such a way for general implementation into high fidelity fuel performance codes or fuel performance codes used for safety analyses.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Non-Targeted Effects and the Dose Response for Heavy Ion Tumorigenesis

BACKGROUND: There is no human epidemiology data available to estimate the heavy ion cancer risks experienced by astronauts in space. Studies of tumor induction in mice are a necessary step to estimate risks to astronauts. Previous experimental data can be better utilized to model dose response for heavy ion tumorigenesis and plan future low dose studies. DOSE RESPONSE MODELS: The Harderian Gland data of Alpen et al.[1-3] was re-analyzed [4] using non-linear least square regression. The data set measured the induction of Harderian gland tumors in mice by high-energy protons, helium, neon, iron, niobium and lanthanum with LET s ranging from 0.4 to 950 keV/micron. We were able to strengthen the individual ion models by combining data for all ions into a model that relates both radiation dose and LET for the ion to tumor prevalence. We compared models based on Targeted Effects (TE) to one motivated by Non-targeted Effects (NTE) that included a bystander term that increased tumor induction at low doses non-linearly. When comparing fitted models to the experimental data, we considered the adjusted R2, the Akaike Information Criteria (AIC), and the Bayesian Information Criteria (BIC) to test for Goodness of fit.In the adjusted R2test, the model with the highest R2values provides a better fit to the available data. In the AIC and BIC tests, the model with the smaller values of the summary value provides the better fit. The non-linear NTE models fit the combined data better than the TE models that are linear at low doses. We evaluated the differences in the relative biological effectiveness (RBE) and found the NTE model provides a higher RBE at low dose compared to the TE model. POWER ANALYSIS: The final NTE model estimates were used to simulate example data to consider the design of new experiments to detect NTE at low dose for validation. Power and sample sizes were calculated for a variety of radiation qualities including some not considered in the Harderian Gland data set and with different background tumor incidences. We considered different experimental designs with varying number of doses and varying low doses dependant on the LET of the radiation. The optimal design to detect a NTE for an individual ion had 4 doses equally spaced below a maximal dose where bending due to cell sterilization was < 2%. For example at 100 keV/micron we would irradiate at 0.03 Gy, 0.065 Gy, 0.13 Gy, and 0.26 Gy and require 850 mice including a control dose for a sensitivity to detect NTE with 80% power. Sample sizes could be improved by combining ions similar to the methods used with the Harderian Gland data.

Chappelli, Lori J.↗

Experimental and theoretical studies on the elasticity of tungsten to 13 GPa

Compressional (V_P) and shear wave (V_S) velocities of polycrystalline tungsten have been measured up to ~13 GPa at room temperature using ultrasonic interferometry in a multi-anvil apparatus. Using finite strain equation of state approaches, the elastic bulk and shear moduli and their pressure dependences are derived yielding $K_{S0}$= 325.9 ± 4.8 GPa, $G_0$ =164.1±2.5 GPa, $K^{'}_{S0}$ =3.65 ± 0.05 and $G^{'}_0$ =1.28 ± 0.02. On the basis of the current experimental data, the high-pressure behavior of Young’s modulus, Poisson’s ratio and ductility/brittleness for tungsten are also investigated. Complementary to the experimental data, the single crystal elastic constants, as well as the elastic anisotropy of tungsten are computed using density functional theory (DFT). The Voigt-Reuss-Hill average of the bulk and shear moduli calculated using the single crystal elastic constants from DFT are found comparable to the current experimental results within about 5%. Here, the present study offers a dataset for the elasticity of polycrystalline bcc tungsten to a maximum pressure more than 25-fold higher than other previous ultrasonic studies, which can further our understanding about the elastic, mechanical and electronic properties of tungsten under extreme conditions as well as thermodynamic modelling of its alloys.

36 MATERIALS SCIENCE↗

Strain-Life Assessment of Grainex Mar-M 247 for NASA's Turbine Seal Test Facility

NASA s Turbine Seal Test Facility is used to test air-to-air seals for use primarily in advanced jet engine applications. Combinations of high temperature, high speed, and high pressure limit the disk life, due to the concern of crack initiation in the bolt holes of the Grainex Mar-M 247 disk. The primary purpose of this current work is to determine an inspection interval to ensure safe operation. The current work presents high temperature fatigue strain-life data for test specimens cut from an actual Grainex Mar-M 247 disk. Several different strain-life models were compared to the experimental data including the Manson-Hirschberg Method of Universal Slopes, the Halford-Nachtigall Mean Stress Method, and the Modified Morrow Method. The Halford-Nachtigall Method resulted in only an 18 percent difference between predicted and experimental results. Using the experimental data at a 99.95 percent prediction level and the presence of 6 bolt holes it was found that the disk should be inspected after 665 cycles based on a total strain of 0.5 percent at 649 C.

Delgado, Irebert R.↗

Myna

The additive manufacturing (AM) community has been developing digital factory tools over the past decade to better leverage the multi-modal process data coming out of the advanced manufacturing process. As a result, numerous databases of additive manufacturing process data exist in the literature and in the archival storage of disparate research groups. While some efforts have been made to create a standard ontology for storing and sharing AM data, in practice a variety of data structures are used to store AM build data, even within a single institution. This causes many problems for maintainability and extensibility when attempting to integrate computational modeling tools with experimental data to either validate models or to provide further insight into results and trends. Myna is a Python-based framework that aims to decrease the effort needed to connect individual computational models to the variety of AM process data that exist in different research groups and institutions. This type of software is sometimes referred to as "middleware" or “glueware,” in that it connects disparate databases and applications into a single computational ecosystem. Instead of maintaining unique interfaces between each application and each database, developers can create a single interface from each application to Myna and thereby gain access to the implemented database connections. Similarly, developing a database connection in Myna provides access to the developed simulation applications. This framework greatly simplifies the maintainability of model applications that rely on experimental data. Using external simulation tools, users will also be able to run pre-configured workflows using the built-in workflow manager. Several examples of input files are provided with Myna for different workflows, including melt pool geometry predictions and detailed melt pool and solidification microstructure predictions.

Knapp, GerryL. [Oak Ridge National Laboratory (ORN↗

Development of a Thermophysical Properties Model for Flowsheet Simulation of Biomass Pyrolysis Processes

A properties model was developed for use in commercial process simulators to model pyrolysis of lignocellulosic biomass. The component list was chosen to enable process simulations based on a recently published lumped pyrolysis kinetics model. Since many of the compounds involved in pyrolysis are not found in simulator databanks, estimation based on available literature data was used to establish missing parameters. Standard solid enthalpy of formation, solid heat capacity, and solid density estimates calculated from the limited experimental data available were prepared for six biomass constituents and nine intermediate and end-products of their pyrolysis. Ideal gas enthalpy of formation and heat capacity, critical property, and vapor pressure estimates were prepared for another four pyrolysis end-products and one biomass component. The estimates were all validated against the closest available experimental data in the literature. The addition of these new components and properties allows thermodynamically rigorous simulation of lumped biomass pyrolysis reactions with accurate energy balances. Furthermore enthalpies of reaction calculated from the properties model were compared with reported reaction enthalpies for the same lumped biomass pyrolysis reactions and found to be in general agreement.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nuclear Data Sheets for A=188☆

Evaluated nuclear structure and decay data for all nuclei with mass number A=188 (Lu, Hf, Ta, W, Re, Os, Ir, Pt, Au, Hg, Tl, Pb, Bi, Po) are presented. The experimental data are compiled and evaluated, and best values for level and gamma-ray energies, quantum numbers, lifetimes, gamma-ray intensities, and other nuclear properties are recommended. Inconsistencies and discrepancies that exist in the literature are noted. This work supersedes the earlier evaluation by Balraj Singh (2002Si10), published in Nuclear Data Sheets 95, 387 (2002). The gamma-ray transition probabilities were calculated using the ENSDF analysis program ruler (www-nds.iaea.org/public/ensdf{sub p}gm/). However, the reader should be warned that the program may produce incorrect results when dealing with non-symmetric uncertainties.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Correlated Anion Disorder in Heteroanionic Cubic TiOF 2

Resolving anion configurations in heteroanionic materials is crucial for understanding and controlling their properties. For anion-disordered oxyfluorides, conventional Bragg diffraction cannot fully resolve the anionic structure, necessitating alternative structure determination methods. We have investigated the anionic structure of anion-disordered cubic (ReO 3 -type) TiOF 2 using X-ray pair distribution function (PDF), 19 F MAS NMR analysis, density functional theory (DFT), cluster expansion modeling, and genetic-algorithm structure prediction. Our computational data predict short-range anion ordering in TiOF 2 , characterized by predominant cis-[O 2 F 4 ] titanium coordination, resulting in correlated anion disorder at longer ranges. To validate our predictions, we generated partially disordered supercells using genetic-algorithm structure prediction and computed simulated X-ray PDF data and 19 F MAS NMR spectra, which we compared directly to experimental data. To construct our simulated 19 F NMR spectra, we derived new transformation functions for mapping calculated magnetic shieldings to predicted magnetic chemical shifts in titanium (oxy)fluorides, obtained by fitting DFT-calculated magnetic shieldings to previously published experimental chemical shift data for TiF 4 . We find good agreement between our simulated and experimental data, which supports our computationally predicted structural model and demonstrates the effectiveness of complementary experimental and computational techniques in resolving anionic structure in anion-disordered oxyfluorides. From additional DFT calculations, we predict that increasing anion disorder makes lithium intercalation more favorable by, on average, up to 2 eV, highlighting the significant effect of variations in short-range order on the intercalation properties of anion-disordered materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Mechanical separations of corn stover anatomical fractions in an integrated feedstock preprocessing system: An experimental and data-driven modeling study

High variabilities of material attributes in lignocellulosic biomass present risks for biofuel and biochemical productions and must be mitigated via preprocessing. Since almost no mechanical device is originally designed for processing biomass, how to operate existing apparatuses with efficient performance has not been investigated extensively. This work presents a study on an integrated screening and air classification to separate cobs and stalks from husks and leaves in corn stover. Prototype machine learning models were developed to assess the feasibility of predicting the process outcome based on the measurable parameters. The models trained upon limited experimental data rendered decent predictive accuracy of yield and purity. The experimental data and modeling results collectively suggest decreasing throughput leads to a higher purity. To the contrary, if throughput increases, a lower purity is likely. A possible trade-off between yield and purity of the separated streams indicates the need for optimal combinations of feedstock size, moisture, and throughput to achieve optimized separations. The results of this study also suggest the need to further improve model predictability by developing more accurate formulations for physics governing the integrated unit operations. To accomplish this, additional experimental data needs to be generated for model training.

09 - BIOMASS FUELS↗

Structural stability of thin overhanging walls during material extrusion additive manufacturing of thermoset-based ink

Recent developments have enabled material extrusion additive manufacturing of thermoset-based composite inks on the large scale. In addition, printing out-of-plane components is of broad interest to the polymer material extrusion community. Here, we address some of the challenges associated with both large-scale and out-of-plane thermoset material extrusion additive manufacturing by studying the height at which thin overhanging walls collapse. Walls at a range of overhang angles were printed until they collapsed. An optical camera captured the profile of each wall throughout the print, allowing the collapse height to be identified and the geometric fidelity to the programmed angle to be evaluated. Using previously measured rheological properties, predictive models were generated to approximate the collapse height and profile of the deflected walls. First, an analytical model was created to predict the height at which the walls would yield. The analytical model assumes the walls exhibit a perfectly linear profile; however, experiments proved this assumption to be false. Therefore, a finite element simulation was developed to account for the elastic deflection that occurs during printing. The finite element simulation predicts both the yield height and the deflected profile after the deposition of each layer. For the properties of the thermoset ink used here, the yield height predicted by the analytical model and finite element simulation are virtually identical. These predictions match experimental data reasonably well, but minor errors are observed. Accounting for the fully plastic moment appears to explain the small mismatch between experimental data and predictions. Additionally, the finite element simulation provides an excellent prediction of the deflected profile before the wall begins to collapse. Finally, by demonstrating that the collapse height and deflected profile of thin overhanging walls can be predicted, this work illustrates how the soft viscoelastic properties of thermoset-based composite inks limit the scale of a key feature required to print some nonplanar components. It also provides a basis to tailor in-process curing systems to suppress deflection and collapse of thin overhanging walls.

36 MATERIALS SCIENCE↗

Supersymmetry and {sup 198}Hg

The energy spectrum and electromagnetic transition properties of the supermultiplet members with two proton fermions can be constructed using the dynamical U{sub v}(6/12) x U{sub {pi}}(6/4) extended supersymmetry. In order to investigate predictions of the two proton fermion--four neutron boson supermultiplet member {sup 198}Hg, an experiment with the HORUS cube {gamma}-ray spectrometer at the Cologne TANDEM accelerator was performed using the {sup 196}Pt({alpha},2n){sup 198}Hg reaction. By analyzing {gamma}{gamma} coincidence spectra and {gamma}{gamma} angular correlations, the required experimental data--level and decay energies, level spins and multipole mixing ratios--could be obtained. For the low-energy states, the experimental data show good agreement with theory.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Large-Scale Structure of Chromatin: A Fractal Globule or a Logarithmic Fractal?

Two physical models are considered to describe the large-scale structure of chromatin in the nucleus of a biological cell in the interphase state: a fractal globule model and a logarithmic fractal model. Based on the classification of fractal objects developed by the small-angle neutron scattering (SANS) method, it is shown that the fractal globule model does not satisfy the experimental data on small-angle neutron scattering by the nuclei of biological cells. Conversely, the logarithmic fractal model well describes the experimental data on SANS and, hence, provides a good approximation to describe the large-scale structure of chromatin. The logarithmic fractal model predicts that the nuclear space is exactly half-filled with chromatin, and the second half consists of interchromatin voids filled with nucleoplasma in which various nuclear processes occur. Thus, two opposing trends are balanced in the structural organization of chromatin: an increase in the surface area of chromatin in the cell nucleus (accessibility to external agents) and a decrease in the volume occupied by chromatin (compactness of the nucleus).

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

An Heuristic Drift-Based Model of the Power Scrape-Off Width in H-Mode Tokamaks

An heuristic model for the plasma scrape-off width in H-mode plasmas is introduced. Grad B and curv B drifts into the SOL are balanced against sonic parallel flows out of the SOL, to the divertor plates. The overall mass flow pattern posited is a modification for open field lines of Pfirsch-Shlüter flows to include sinks to the divertors. These assumptions result in an estimated SOL width of 2aρp/R. They also result in a first-principles calculation of the particle confinement time of H-mode plasmas, qualitatively consistent with experimental observations. It is next assumed that anomalous perpendicular electron thermal diffusivity is the dominant source of heat flux across the separatrix, investing the SOL width, defined above, with heat from the main plasma. The separatrix temperature is calculated based on a two-point model balancing power input to the SOL with Spitzer-Härm parallel thermal conduction losses to the divertor. This results in an heuristic closed-form prediction for the power scrape-off width that is in remarkable quantitative agreement both in absolute magnitude and in scaling with recent experimental data. Further work should include full numerical calculations, including all magnetic and electric drifts, as well as more thorough comparison with experimental data.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experimental and Computational Analysis of NEAMS Pebble Bed Reactors

The Advanced High-Temperature Pebble Bed Reactor concept leverages a particle-based fuel format consisting of discrete spherical graphite pebbles arrayed in a packed bed architecture. Thermal regulation achieved via flow of gas (e.g., helium) or liquid (e.g., molten salt) coolants through the void spaces between pebbles in the bed (characteristic pebble diameters: ~ 6 cm, gas cooled; ~ 3 cm, liquid cooled). This design is of interest owing to inherent advantages including passive safety features and highly efficient heat transfer characteristics that enable high power densities to be achieved. Fully leveraging these advantages requires a fundamental understanding of the complex coolant flow structure within the pebble-shaped fuel bed. Unfortunately, complexities associated with non-invasively probing the micro-scale flow phenomena within the complex network of void spaces between pebbles have hindered efforts to characterize the underlying transport phenomena. Without this fundamental foundation, it becomes challenging to rationally construct macroscopic transport models based upon volume averages of micro-scale parameters that accurately capture the observed flow behavior. Consequently, this lack of fundamental knowledge has limited previous work to coarse comparisons between theory and extremely limited experimental data. Moreover, these comparisons have been made only in terms of integral or macroscopic results. Therefore, multipoint measurements with a high level of spatial and temporal resolution are critically needed to fully map the complex flow patterns and to provide data at high spatial density to permit accurate volume averaging in the pebble bed. For this project, we performed a coordinated experimental and computational effort to quantitatively map the full-field velocity and temperature fields in the interstitial spaces within the pebble bed. The major accomplishments of this project included the important knowledge acquired for the flow mixing and heat transfer in the interstitial pore scales, the effects of flow mixing in the near-wall and far-wall regions, and the by-pass flows of pebble bed systems. The produced high-resolution experimental data (not broadly available in existing literature) were then used for the numerical studies enabling the refinement and validation of standard simulation tools (Nek5000).

42 ENGINEERING↗