Search NASA⌕ Search

SEARCH · Search NASA

Results for “sampling methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Dynamic Stability Test Technique for Blunt Bodies in a Magnetic Suspension and Balance System

Techniques for the measurement of subsonic dynamic stability derivatives of blunt-body re-entry capsules are being developed using a Magnetic Suspension and Balance System at NASA Langley Research Center. The measured aerodynamics of a 45-degree sphere-cone similar to configurations being considered for Mars Sample Return Earth Entry Vehicle are reported. A novel test method has been developed where forced oscillatory translation of a test article is used to excite yaw attitude oscillations. The forced motion is then halted to observe free-to-oscillate behavior of the test article. Parameter identification methods are used to extract drag as well as static and dynamic yawing moment stability characteristics from the measured forces and observed attitude histories. This combination of forced excitation followed by free-to-oscillate dynamics is a repeatable method to produce test article attitude histories that can be used to measure aerodynamic characteristics.

Entry Systems Modeling↗

Method Developed for the High-Temperature Nondestructive Evaluation of Fiber-Reinforced Silicon Carbide Ceramic Matrix Composites

Ceramic matrix composites have emerged as candidate materials to allow higher operating temperatures (1000 to 1400 C) in gas turbine engines. A need, therefore, exists to develop nondestructive methods to evaluate material integrity at the material operating temperature by monitoring thermal and mechanical fatigue. These methods would also have potential as quality inspection tools. The goal of this investigation at the NASA Lewis Research Center is to survey and correlate the temperature-dependent damping and stiffness of advanced ceramic composite materials with imposed thermal and stress histories that simulate in-service turbine engine conditions. A typical sample size of 100 by 4 by 2 cubic millimeters, along with the specified stiffness and density, placed the fundamental vibration frequencies between 100 and 2000 Hz. A modified Forster apparatus seemed most applicable to simultaneously measure both damping and stiffness. Testing in vacuum reduced the effects of air on the measurements. In this method, a single composite sample is vibrated at its fundamental tone; then suddenly, the mechanical excitation is removed so that the sample's motion freely decays with time. Typical results are illlustrated in this paper.

Goldsby, Jon C.↗

Improved Creep Measurements for Ultra-High Temperature Materials

Our team has developed a novel approach to measuring creep at extremely high temperatures using electrostatic levitation (ESL). This method has been demonstrated on niobium up to 2300 C, while ESL has melted tungsten (3400 C). This method has been extended to lower temperatures and higher stresses and applied to new materials, including a niobium-based superalloy, MASC. High-precision machined spheres of the sample are levitated in the NASA MSFC ESL, a national user facility and heated with a laser. The samples are rotated with an induction motor at up to 30,000 revolutions per second. The rapid rotation loads the sample through centripetal acceleration, producing a shear stress of about 60 MPa at the center, causing the sample to deform. The deformation of the sample is captured on high-speed video, which is analyzed by machine-vision software from the University of Massachusetts. The deformations are compared to finite element models to determine the constitutive constants in the creep relation. Furthermore, the non-contact method exploits stress gradients within the sample to determine the stress exponent in a single test.

Hyers, Robert W.↗

Benchmarking Surface Tension Measurement Method using two Oscillation Modes in Levitated Liquid Metals

The Faraday forcing method in levitated liquid droplets has recently been introduced as a method for measuring surface tension using resonance. By subjecting an electrostatically-levitated liquid metal droplet to a continuous, oscillatory, electric field, at a frequency nearing that of the droplet’s first principal mode of oscillation (known as mode 2), the method was previously shown to determine surface tension of materials that would be particularly difficult to process by other means, e.g. liquid metals and alloys. It also offers distinct advantages in future work involving high viscosity samples because of the continuous forcing approach. This work presents 1) a benchmarking experimental method to measure surface tension by excitation of the second principal mode of oscillation (known as mode 3) in a levitated liquid droplet and 2) a more rigorous quantification of droplet excitation using a projection method. Surface tension measurements compare favorably to literature values for Zirconium, Inconel 625, and Rhodium, using both modes 2 and 3. Thus, this new method serves as a credible, self-consistent benchmarking technique for the measurement of surface tension

Levitation↗

Microbial Food Safety in Space Production Systems

While traveling to deep space is difficult for many reasons, food is a crucial one. Round-trip Mars mission scenarios last 3 years, demanding food with a shelf-life of 5 years; this means that feeding human crew sustainably for long-duration missions beyond low Earth orbit (LEO) will ultimately lead to a paradigm shift away from the current Earth-based food production system, which depends upon storing and transporting prepackaged foods, and toward bio-regenerative production of food in space. Pharmaceuticals and nutritional supplements face similar challenges. Moreover, the methods we currently use to detect dangerous microbes in food require sample return to Earth, a situation not viable for deep-space missions. While the science behind generating foods and bioproducts is covered by other white papers, in this paper we discuss a crucial gap uniting all of them: how to ensure that such products are free of unwanted microbial contamination and safe for crew to consume. Because Earth-based food safety systems cannot be directly applied in space, safety assurance is currently a critical bottleneck in the space production of food and other bioproducts. Future sustainable deep-space missions will require NASA to devote more resources in the coming decade to understanding the biological and physical science principles underlying microbial food safety in space, and to developing efficient, reliable methods in this area.

microbiology↗

The effect of maturation on the configuration of pristane in sediments and petroleum

The absolute stereochemistry of pristane in a sample of contemporary marine zooplankton, Messel shale (Germany) and Djatibarang (Java) crude has been determined by gas chromatographic methods. The relative stereochemistry in Irati shale (Brazil), Green River (U.S.) crude, Halibut (Australia) crude has also been determined, and confirmed for a sample of the Green River shale. The stereoisomer distributions indicate a loss of stereospecificity of the phytol-derived 6(R), 10(S) pristane with increasing geological maturation. For example, the least mature geological sample, the Eocene Messel shale, contains solely the 6(R), 10(S) isomer, whereas a mature sample, Djatibarange crude, contains 50% of the 6(R), 10(S) isomer and 25% of each of the 6(R), 10(R) and 6(S), 10(S) isomers.

Patience, R. L.↗

Cosmic ray interactions in the ground: Temporal variations in cosmic ray intensities and geophysical studies

Temporal variations in cosmic ray intensity have been deduced from observations of products of interactions of cosmic ray particles in the Moon, meteorites, and the Earth. Of particular interest is a comparison between the information based on Earth and that based on other samples. Differences are expected at least due to: (1) differences in the extent of cosmic ray modulation, and (2) changes in the geomagnetic dipole field. Any information on the global changes in the terrestrial cosmic ray intensity is therefore of importance. In this paper a possible technique for detecting changes in cosmic ray intensity is presented. The method involves human intervention and is applicable for the past 10,000 yrs. Studies of changes over longer periods of time are possible if supplementary data on age and history of the sample are available using other methods. Also discussed are the possibilities of studying certain geophysical processes, e.g., erosion, weathering, tectonic events based on studies of certain cosmic ray-produced isotopes for the past several million years.

Lal, D.↗

The interaction between a solid body and viscous fluid by marker-and-cell method

A computational method for solving nonlinear problems relating to impact and penetration of a rigid body into a fluid type medium is presented. The numerical techniques, based on the Marker-and-Cell method, gives the pressure and velocity of the flow field. An important feature in this method is that the force and displacement of the rigid body interacting with the fluid during the impact and sinking phases are evaluated from the boundary stresses imposed by the fluid on the rigid body. A sample problem of low velocity penetration of a rigid block into still water is solved by this method. The computed time histories of the acceleration, pressure, and displacement of the block show food agreement with experimental measurements. A sample problem of high velocity impact of a rigid block into soft clay is also presented.

Cheng, R. Y. K.↗

Choice of method for discretization of continuous systems

The paper discusses and compares several common methods of discretizing the transfer function of a continuous control system so that a digital computer can be used. The discretization effect on the frequency response attenuation of the simple transfer function G(s) = 1/(s + 1) is illustrated for the Tusting, Boxer-Thaler, Madwed, linear segment approximation, and stair-step with half period advanced methods. The input frequency must be significantly lower than one-half the sampling error to have negligible discretization error. Phase differences due to discretization are also plotted, and it is seen that the zero-order hold contributes much more phase shift than that due to discretization. In situations where zero-order hold must follow a computer, the method of discretization of a continuous system is not a major factor if phase shift is important.

Mcvey, E. S.↗

Aligned and Electrospun Piezoelectric Polymer Fiber Assembly and Scaffold

A scaffold assembly and related methods of manufacturing and/or using the scaffold for stem cell culture and tissue engineering applications are disclosed which at least partially mimic a native biological environment by providing biochemical, topographical, mechanical and electrical cues by using an electroactive material. The assembly includes at least one layer of substantially aligned, electrospun polymer fiber having an operative connection for individual voltage application. A method of cell tissue engineering and/or stem cell differentiation uses the assembly seeded with a sample of cells suspended in cell culture media, incubates and applies voltage to one or more layers, and thus produces cells and/or a tissue construct. In another aspect, the invention provides a method of manufacturing the assembly including the steps of providing a first pre-electroded substrate surface; electrospinning a first substantially aligned polymer fiber layer onto the first surface; providing a second pre-electroded substrate surface; electrospinning a second substantially aligned polymer fiber layer onto the second surface; and, retaining together the layered surfaces with a clamp and/or an adhesive compound.

Scott-Carnell, Lisa A.↗

Long-term storage of salivary cortisol samples at room temperature

Collection of saliva samples for the measurement of cortisol during space flights provides a simple technique for studying changes in adrenal function due microgravity. In the present work, several methods for preserving saliva cortisol at room temperature were investigated using radioimmunoassays for determining cortisol in saliva samples collected on a saliva-collection device called Salivettes. It was found that a pretreatment of Salivettes with citric acid resulted in preserving more than 85 percent of the salivary cortisol for as long as six weeks. The results correlated well with those for a sample stored in a freezer on an untreated Salivette.

Chen, Yu-Ming↗

A technique to measure the thermal diffusivity of high T(sub c) superconductors

High T(sub c) superconducting electrical current leads and ground straps will be used in cryogenic coolers in future NASA Goddard Space Flight Center missions. These superconducting samples will be long, thin leads with a typical diameter of two millimeters. A longitudinal method is being developed to measure the thermal diffusivity of candidate materials for this application. This technique will use a peltier junction to supply an oscillatory heat wave into one end of a sample and will use low mass thermocouples to follow the heat wave along the sample. The thermal diffusivity will be calculated using both the exponential decay of the heat wave and the phase shift of the wave. Measurements will be done in a cryostat between 10 K and room temperature.

Powers, Charles E.↗

Electron Spin Resonance (ESR) studies of returned comet nucleus samples

The most important objective of the Comet Nucleus Sample Returm Mission is to return samples which could reflect formation conditions and evolutionary processes in the early solar nebula. It is expected that the returned samples will consist of fine-grained silicate materials mixed with ices composed of simple molecules such as H2O, NH3, CH4 as well as organics and/or more complex compounds. Because of the exposure to ionizing radiation from cosmic-ray, gamma-ray, and solar wind protons at low temperature, free radicals are expected to be formed and trapped in the solid ice matrices. The kind of trapped radical species together with their concentration and thermal stability can be used as a dosimeter as well as a geothermometer to determine thermal and radiation histories as well as outgassing and other possible alternation effects since the nucleus material was formed. Since free radicals that are known to contain unpaired electrons are all paramagnetic in nature, they can be readily detected and characterized in their native form by the Electron Spin Resonance (ESR) method. In fact, ESR has been shown to be a non-destructive, highly sensitive tool for the detection and characterization of paramagnetic, ferromagnetic, and radiation damage centers in terrestrial and extraterrestrial geological samples. The potential use of ESR as an effective method in the study of returned comet nucleus samples, in particular, in the analysis of fine-grained solid state icy samples is discussed.

Tsay, Fun-Dow↗

Statistical methods for efficient design of community surveys of response to noise: Random coefficients regression models

Research studies of residents' responses to noise consist of interviews with samples of individuals who are drawn from a number of different compact study areas. The statistical techniques developed provide a basis for those sample design decisions. These techniques are suitable for a wide range of sample survey applications. A sample may consist of a random sample of residents selected from a sample of compact study areas, or in a more complex design, of a sample of residents selected from a sample of larger areas (e.g., cities). The techniques may be applied to estimates of the effects on annoyance of noise level, numbers of noise events, the time-of-day of the events, ambient noise levels, or other factors. Methods are provided for determining, in advance, how accurately these effects can be estimated for different sample sizes and study designs. Using a simple cost function, they also provide for optimum allocation of the sample across the stages of the design for estimating these effects. These techniques are developed via a regression model in which the regression coefficients are assumed to be random, with components of variance associated with the various stages of a multi-stage sample design.

Tomberlin, T. J.↗

Lunar Transport Vehicle Ocupant Protection Requirements

INTRODUCTION The National Aeronautics and Space Administration (NASA) is preparing for future Artemis missions that will return humans to the lunar surface. A critical piece of these future missions is the Lunar Transport Vehicle (LTV), a transportation device to be used on the lunar surface. A vehicular method of transportation will allow for longer duration missions with increased capabilities to conduct research and transport soil, geological samples, or other materials of interest. The objective of this project is to provide occupant protection guidance for the design of the LTV. METHODS At the time of writing of occupant protection requirements, much of the LTV design is unknown. However, several general assumptions have been established. It is assumed that the LTV will be an unpressurized crewed rover with the occupant(s) wearing an EVA suit. Additionally, the occupant must be protected using established health limits as governing criteria to protect the occupant from hazardous levels of acceleration, jerk, and vibration. In addition to the health limits, it is expected that the LTV shall provide a comfortable transportation solution to Lunar operations. Several restraint configurations have been considered to allow for seated and standing operation of the vehicle. RESULTS Preliminary recommendations and metrics were put forward by a cross functional working group with members from Johnson Space Center and Ames Research Center. Exposure to acceleration, vibration, and jerk metrics above the proposed limits could create a risk of occupant injury. In addition to satisfying crew health needs, these limits permit the occupant to meet performance objectives including operating the vehicle and reading displays while traversing the Lunar surface. Initial guidance was refined during a Technical Interchange Meeting with external subject matter experts in industry, academia, and United States Air Force. CONCLUSION Operating a crewed vehicle in a lunar environment is a novel problem with few analogs to provide data. Based on terrestrial data from ISO & MIL Standards, occupant protection recommendations have been identified with several assumptions made about reduced gravity and deconditioned occupants. If the design of the vehicle attenuates energetics to levels below those put forward, there is high confidence the occupant will be able to repetitively operate the vehicle without physical harm or operational issues.

K Dolick↗

Extension of the Time-Spectral Approach to Overset Solvers for Arbitrary Motion

Forced periodic flows arise in a broad range of aerodynamic applications such as rotorcraft, turbomachinery, and flapping wing configurations. Standard practice involves solving the unsteady flow equations forward in time until the initial transient exits the domain and a statistically stationary flow is achieved. It is often required to simulate through several periods to remove the initial transient making unsteady design optimization prohibitively expensive for most realistic problems. An effort to reduce the computational cost of these calculations led to the development of the Harmonic Balance method [1, 2] which capitalizes on the periodic nature of the solution. The approach exploits the fact that forced temporally periodic flow, while varying in the time domain, is invariant in the frequency domain. Expanding the temporal variation at each spatial node into a Fourier series transforms the unsteady governing equations into a steady set of equations in integer harmonics that can be tackled with the acceleration techniques afforded to steady-state flow solvers. Other similar approaches, such as the Nonlinear Frequency Domain [3,4,5], Reduced Frequency [6] and Time-Spectral [7, 8, 9] methods, were developed shortly thereafter. Additionally, adjoint-based optimization techniques can be applied [10, 11] as well as frequency-adaptive methods [12, 13, 14] to provide even more flexibility to the method. The Fourier temporal basis functions imply spectral convergence as the number of harmonic modes, and correspondingly number of time samples, N, is increased. Some elect to solve the equations in the frequency domain directly, while others choose to transform the equations back into the time domain to simplify the process of adding this capability to existing solvers, but each harnesses the underlying steady solution in the frequency domain. These temporal projection methods will herein be collectively referred to as Time-Spectral methods. Time-Spectral methods have demonstrated marked success in reducing the computational costs associated with simulating periodic forced flows, but have yet to be fully applied to overset or Cartesian solvers for arbitrary motion with dynamic hole-cutting. Overset and Cartesian grid methodologies are versatile techniques capable of handling complex geometry configurations in practical engineering applications, and the combination of the Time-Spectral approach with this general capability potentially provides an enabling new design and analysis tool. In an arbitrary moving-body scenario for these approaches, a Lagrangian body moves through a fixed Eulerian mesh and mesh points in the Eulerian mesh interior to the solid body are removed (cut or blanked), leaving a hole in the Eulerian mesh. During the dynamic motion some gridpoints in the domain are blanked and do not have a complete set of time-samples preventing a direct implementation of the Time-Spectral method. Murman[6] demonstrated the Time-Spectral approach for a Cartesian solver with a rigid domain motion, wherein the hole cutting remains constant. Similarly, Custer et al. [15, 16] used the NASA overset OVERFLOW solver and limited the amount of relative motion to ensure static hole-cutting and interpolation. Recently, Mavriplis and Mundis[17] demonstrated a qualitative method for applying the Time-Spectral approach to an unstructured overset solver for arbitrary motion. The goal of the current work is to develop a robust and general method for handling arbitrary motion with the Time-Spectral approach within an overset or Cartesian mesh method, while still approaching the spectral convergence rate of the original Time-Spectral approach. The viscous OVERFLOW solver will be augmented with the new Time-Spectral algorithm and the capability of the method for benchmark problems in rotorcraft and turbomachinery will be demonstrated. This abstract begins with a brief synopsis of the Time-Spectral approach for overset grids and provides details of e current approach to allow for arbitrary motion. Model problem results in one and two dimensions are included to demonstrate the viability of the method and the convergence properties. Section IV briefly outlines the implementation into the OVERFLOW solver, and the abstract closes with a description of the benchmark test cases which will be included in the final paper.

Leffell, Joshua Isaac↗

A Fast Monte Carlo Method for Model-Based Prognostics Based on Stochastic Calculus

This work proposes a fast Monte Carlo method to solve differential equations utilized in model-based prognostics. The methodology is derived from the theory of stochastic calculus, and the goal of such a method is to speed up the estimation of the probability density functions describing the independent variable evolution over time. In the prognostic scenarios presented in this paper, the stochastic differential equations describe variables directly or indirectly related to the degradation of a monitored system. The method allows the estimation of the probability density functions by solving the deterministic equation and approximating the stochastic integrals using samples of the model noise. By so doing, the prognostic problem is solved without the Monte Carlo simulation based on Euler's forward method, which is typically the most time consuming task of the prediction stage. Three different prognostic scenarios are presented as proof of concept: (i) life prediction of electrolytic capacitors, (ii) remaining time to discharge of Lithium-ion batteries, and (iii) prognostic of cracked structures under fatigue loading. The paper shows how the method produces probability density functions that are statistically indistinguishable from the distributions estimated with Euler's forward Monte Carlo simulation. However, the proposed solution is orders of magnitude faster when computing the time-to-failure distribution of the monitored system. The approach may enable complex real-time prognostics and health management solutions with limited computing power.

stochastic calculus↗