Search NASA⌕ Search

SEARCH · Search NASA

Results for “variable free”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Flight Mechanics Modeling and Simulation of the Earth Entry System

Introduction: The Mars Sample Return (MSR) Campaign being planned by NASA and ESA has the ambitious goal to return Mars samples back to Earth. This international collaboration had developed a concept of operations that included a ESA-designed Earth Return Orbiter (ERO) and NASA-designed Capture, Containment, and Return System (CCRS). The Earth Entry System (EES), consisting of a protective aeroshell that houses the samples as well as sample containment vessels, would conduct entry, descent, and landing (EDL) on a direct Earth trajectory. The EES would enter on a spin-stabilized ballistic trajectory with the goal to passively achieve aerodynamic stability throughout all regions of flight. The EDL sequence would end with the EES impacting the soft playa soil of the Utah Test and Training Range (UTTR). As of the submission of this abstract, the MSR campaign is undergoing a re-architecture leading to a pause in EES development. However, the novel approaches developed in flight mechanics modeling and simulation can significantly benefit the greater IPPW community in the development of Earth return vehicles. This paper will present the latest state of EES flight mechanics modeling and simulation. The paper will highlight the simulation architecture developed and key lessons learned from understanding of EDL trajectory sensitivities. Modeling and Simulation: Figure 1 provides a high-level concept of operations for the approach, entry, descent, and landing (AEDL) phase of the CCRS-portion of MSR. The objective of EES flight mechanics is to model and simulate the EES trajectory from ERO separation to ground impact at UTTR. A variety of flight mechanics simulation models were utilized to model both exo-atmopsheric and atmospheric portions of flight. 42, a 6-DOF simulation developed at Goddard Space Flight Center, is utilized for propagating the attitude of EES during exo-atmospheric flight. 42 allows for a variety of spin eject mechanism scenarios to be simulated for analysis. 10 minutes prior to entry, the 42 states are handed off to the EDL sims. The prime EDL sim utilized by EES is the Program to Optimize Simulated Trajectories II (POST2), a 6-DOF sim developed at Langley Research Center, and the independent verification and validation EDL sim utilized is DSENDS, a 6-DOF sim developed at Jet Propulsion Laboratory. Figure 2 provides a visualization of the flight mechanics simulation model flow through various points in the AEDL phase. Due to the existence of a variety of sim models, the EES flight mechanics team developed processes for data hand-off. These processes included the development of a centralized coordinate frame document, utilization of a single, centralized simulation input document for all sims to reference, and hand-off files containing both the technical data to be ingested by other flight mechanics sims as well as annotations of modeling assumptions utilized to generate the data. Figure~\ref{fig:post2simarchitecture} provides an overview of the POST2 sim architecture wherein POST2 ingests numerous subsystem models and input files. The dispersed state file generated by MONTE provides the position/velocity state of the trajectory while the 42 Handoff file provides the attitude. The aerodynamics database, delivered by the EES aeroscience team, is utilized to simulate the aerodynamic forces and moments experienced during EDL. A custom atmosphere model, developed by EES atmosphere team, is utilized to simulate the anticipated atmosphere environment around the region of Earth through which the EES trajectory flys. These inputs and subsystem models can be varied depending on the AEDL flight mechanics scenario being simulated. Monte Carlo simulations are utilized to generate statistical AEDL performance metrics in the form of scorecards and violin plots. Furthermore, outputs from the POST2 simulation are utilized for follow-on analyses including aerothermal and landing performance. \section{Flight Mechanics Lessons Learned} Though the EES flight mechanics team uncovered a variety of lessons learned through the analysis conducted to support CCRS through preliminary design review, this paper will highlight the most important lessons. A key AEDL performance goal is to ensure the landing footprint of EES remains on the UTTR south range. A common modeling strategy used in EDL analysis is One-Variable-At-a-Time (OVAT). OVAT analysis provides insight into the key drivers that affect AEDL performance metrics. Figure 3 shows the landing ellipses for single dispersion sources as compared to the baseline aggregate of all dispersions. The figure shows that atmosphere winds alone dominate the size of the footprint ellipse (note: EES does not use a parachute unlike previous Earth-return missions and is in wind-driven free fall for ~5min). The significance of the wind led the EES flight mechanics team to pursue the development of a Custom Atmosphere Model [4], in lieu of EarthGRAM [1], built on actual radiosonde wind measurements around the UTTR-region. This decision was driven by the realism in the generated footprint ellipses and lessons-learned from Stardust [5]. These findings will be invaluable for future Earth-return missions in providing an early understanding of the key drivers affecting footprint size and modeling considerations for which to account. Another lesson learned is tied to the AEDL performance goal of achieving passive stability throughout all regions of flight. It is well understood that blunt-body aeroshells are less stable as they transition from supersonic to subsonic. Eliminating a backshell does help improvestability; however, other phenomena such as roll-induced instability during terminal descent can still arise. The EES flight mechanics team developed stability metrics as tools to better understand the causes of and better predict the onset of dynamic instability. These tools were built upon analytical models developed by Jaffe [3] and Murphy [2]. The tools were shown to both be very accurate in correlation with actual unstable cases and useful in developing stability margin policies based on the vehicle design and simulation considerations (e.g. sphere-cone angle change, mass change, wind turbulence). These tools allowed for the current EES design to demonstrate the ability to achieve passive stability and can be an invaluable tool for consideration in the design of parachute-less Earth-return vehicles.

Rohan Deshmukh↗

Temporal dynamics of free‐living nitrogen fixation in the switchgrass rhizosphere

Abstract Free‐living nitrogen fixation (FLNF) represents an important terrestrial N source and is gaining interest for its potential to contribute plant available N to bioenergy cropping systems. Switchgrass, a cellulosic bioenergy crop, may be particularly reliant on FLNF when grown on low N systems, like marginal lands. However, the potential contributions of FLNF to switchgrass as well as the controls on this process are not well understood. In this study, we evaluated drivers of FLNF rates and N‐fixing microbial (diazotrophic) community composition in field‐grown switchgrass systems over two growing seasons with high temporal sampling. We found that climate variables are strong drivers of FLNF rates in switchgrass systems, compared to other environmental and biological factors including soil nutrients and diazotrophic community composition. Increased soil moisture availability generally promoted FLNF rates, but extreme rainfall events were detrimental. These climate‐related responses suggest a potential for loss of FLNF‐derived N contributions under projected climate shifts. We found a significant, but weak correlation between diazotrophic community composition and FLNF rates. We also observed a significant shift in the diazotrophic community composition between 2017 and 2018 and similarly measured a significant difference in FLNF rates between growing seasons. Lastly, we found that seasonal FLNF N contributions, based on measurement with high temporal resolution, has the potential to meet up to 80% of switchgrass N demands suggesting that FLNF measurements extrapolated from fewer time points or locations may underestimate these potential N contributions.

59 BASIC BIOLOGICAL SCIENCES↗

Monte Carlo Mean Field Treatment of Microbunching Instability in the FERMI@Elettra First Bunch Compressor

Bunch compressors, designed to increase the peak current, can lead to a microbunching instability with detrimental effects on the beam quality. This is a major concern for free electron lasers (FELs) where very bright electron beams are required, i.e. beams with low emittance and energy spread. In this paper, we apply our self-consistent, parallel solver to study the microbunching instability in the first bunch compressor system of FERMI{at}Elettra. Our basic model is a 2D Vlasov-Maxwell system. We treat the beam evolution through a bunch compressor using our Monte Carlo mean field approximation. We randomly generate N points from an initial phase space density. We then calculate the charge density using a smooth density estimation procedure, from statistics, based on Fourier series. The electric and magnetic fields are calculated from the smooth charge/current density using a novel field formula that avoids singularities by using the retarded time as a variable of integration. The points are then moved forward in small time steps using the beam frame equations of motion, with the fields frozen during a time step, and a new charge density is determined using our density estimation procedure. We try to choose N large enough so that the charge density is a good approximation to the density that would be obtained from solving the 2D Vlasov-Maxwell system exactly. We call this method the Monte Carlo Particle (MCP) method.

43 PARTICLE ACCELERATORS↗

SU-F-J-123: CT-Based Determination of DIBH Variability and Its Dosimetric Impact On Post-Mastectomy Plus Regional Nodal Radiation Therapy

Purpose: Breast cancer radiotherapy delivered using voluntary deep inspiration breath-hold (DIBH) requires reproducible breath holds, particularly when matching supraclavicular fields to tangential fields. We studied the impact of variation in DIBHs on CTV and OAR dose metrics by comparing the dose distribution computed on two DIBH CT scans taken at the time of simulation. Methods: Ten patients receiving 50Gy in 25 fractions to the left chestwall and regional lymph nodes were studied. Two simulation CT scans were taken during separate DIBHs along with a free-breathing (FB) scan. The treatment was planned using one DIBH CT. The dose was recomputed on the other two scans using adaptive planning (Pinnacle 9.10) in which the scans are registered using a cross-correlation algorithm. The chestwall, lymph nodes and OARs were contoured on the scans following the RTOG consensus guidelines. The overall translational and rotational variation between the DIBH scans was used to estimate positional variation between breath-holds. Dose metrics between plans were compared using paired t-tests (p < 0.05) and means and standard deviations were reported. Results: The registration parameters were sub-millimeter and sub-degree. Although DIBH significantly reduced mean heart dose by 2.4Gy compared to FB (p < 0.01), no significant changes in dose were observed for targets or OARs between the two DIBH scans. Nodal coverage as assessed by V90% was 90%±8% and 89%±8% for supraclavicular and 99%±2% and 97%±22% for IM nodes. Though a significant decrease (10.5%±12.4%) in lung volume in the second DIBH CT was observed, the lung V20Gy was unchanged (14±2% and 14±3%) between the two DIBH scans. Conclusion: While the lung volume often varied between DIBHs, the CTV and OAR dose metrics were largely unchanged. This indicates that manual DIBH has the potential to provide consistent dose delivery to the chestwall and regional nodes targets when using matched fields.

60 APPLIED LIFE SCIENCES↗

Efficacy of an acoustic hailing device as an avian dispersal tool

Bird strikes are a major safety and financial concern for modern aviation. Audible stimuli are common bird dispersal techniques, but their effectiveness is limited by the saliency and relevance of the stimulus. Furthermore, high ambient sound levels present at airfields might require that effective audible stimuli rely more on total volume (i.e., exceeding physiological tolerances) than ecological relevance. Acoustic hailing devices (AHD) are capable of sound output with a narrow beam width and at volumes high enough to cause physical discomfort at long distances. We tested the effectiveness of an AHD as a dispersal tool on free-ranging birds recognized as hazardous to aviation safety at the Savannah River Site and Phinizy Swamp Nature Park in South Carolina and Georgia, respectively. Our study design included experimental trials with timed-interval counts of birds directly before and after AHD treatment. For most species, counts of birds associated with treatment periods (use of AHD) and control periods (no use of AHD) occurred on different days. Sound treatments yielded variable success at dispersing birds. Specifically, AHD treatment was effective for dispersing vultures (Coragyps atratus and Cathartes aura) and gulls (Laridae), and ineffective for dispersing blackbirds (Icteridae), diving ducks (Aythya, Bucephala, Oxyura), and coots (Fulica americana). These trials were conducted in a relatively quiet environment with birds that were unhabituated to excessive noise, and thus we cannot unequivocally recommend an AHD as a universally effective avian dispersing tool. Furthermore, future research should consider AHD testing integrated with other methods, as well as investigation of treatments that might be salient to specific target species.

60 APPLIED LIFE SCIENCES↗

Towards fully predictive gyrokinetic full- f simulations: validation and triangularity studies in TCV

Designing economical magnetic confinement fusion power plants motivates computational tools that can estimate plasma behavior from engineering parameters without direct reliance on experimental measurement of the plasma profiles. In this work, we present full-f global long-wavelength gyrokinetic simulations of edge and scrape-off layer turbulence in tokamaks that use only magnetic geometry, heating power, and particle inventory as inputs. Unlike many modeling approaches that employ free parameters fitted to experimental data, raising uncertainties when extrapolating to reactor scales. This approach directly simulates turbulence and resulting profiles through gyrokinetics without such empirical adjustments. This is achieved via an adaptive sourcing algorithm in Gkeyll that strictly controls energy injection and emulates particle sourcing due to neutral recycling. We show that the simulated kinetic profiles compare reasonably well with Thomson scattering and Langmuir probe data for Tokamak á Configuration Variable (TCV) discharge #65125, and that the simulations reproduce characteristic features such as blob transport and self-organized electric fields. Applying the same framework to study triangularity effects suggests mechanisms contributing to the improved confinement reported for negative triangularity (NT). Simulations of TCV discharges #65125 and #65130 indicate that NT increases the E x B flow shear (by about 20% in these cases), which correlates with reduced turbulent losses and a modest change in the distribution of power exhaust to the vessel wall. While the physical models contain approximations that can be refined in future work, the predictive capability demonstrated here, evolving multiple profile relaxation times with kinetic electron and ion models in hundreds of GPU hours, indicates the feasibility of using Gkeyll to support design studies of fusion devices.

Hoffmann, Antoine Cyril David [Princeton Plasma Ph↗

Variable features on Mars. VII - Dark filamentary markings on Mars

The paper discusses the location, variability, and possible nature of well-developed patterns of dark filamentary markings in the Mariner 9 photographic records. Although not common on Mars, the markings are concentrated in at least two areas: Depressio Hellespontica and Cerberus/Trivium Charontis. In certain localities, strong winds are required to bring these markings into prominence. The dark filamentary markings seem to be true albedo features controlled by local topography, it being unlikely that they are free linear dunes. The distinctive criss-cross pattern seen in many of the pictures suggests that jointing provides the controlling topographic grid. At this stage it cannot be inferred whether the markings are erosional or depositional in character.

Veverka, J.↗

Experimental evaluation of inlet turbulence, wall boundary layer, surface finish, and fillet radius on small axial turbine state performance

The results of an experimental investigation are presented which establish the effects of surface finish, fillet radius, inlet boundary layer thickness, and free-stream inlet turbulence level on the aerodynamic performance of a small axial flow turbine stator. The principal objective was to help understand why large turbine efficiency is not maintained when a large turbine is scaled to a smaller size and to provide the turbine designer with the performance compromises expected for a small scale design. A comprehensive test matrix was used to gain an understanding of the effects of each variable over the full range of all the other variables.

Kozak, A. A.↗

Calculations of transonic potential flows by a parameter free procedure

A parameter-free computational procedure for transonic potential flows around an airfoil is presented. The method is based on an inexact, Newton-like iterative scheme, and a preconditioned minimal residual algorithm is used to solve the linear system of equations arising at each iterate. This iterative procedure is formulated so that the difficulties associated with the approximate factorization technique, namely the requirement of iteration parameters and the boundary conditions for the intermediate variable are eliminated. Numerical experiments are given for potential flows around NACA 0012 airfoil with different Mach numbers and different angles of attack. These results are then compared with those obtained by the approximate factorization techniques.

Wong, Y. S.↗

The Effect of the Walls in Closed Type Wind Tunnels

A series of tests has been conducted during the period 1925-1927 by the National Advisory Committee for Aeronautics in the variable-density wind tunnel on several airfoil models of different sizes and sections to determine the effect of tunnel-wall interference and to determine a correction which can be applied to reduce the error caused thereby. The use of several empirical corrections was attempted with little success. The Prandtl theoretical corrections give the best results, and their use is recommended for correcting closed wind tunnel results to the conditions of free air. An appendix is attached wherein the experimentally determined effect of the walls on the tunnel velocity very close to their surface is given. This is of special interest because a "scale effect" was found in the boundary layer with a change in the density of the tunnel air.

Higgins, George J↗

Implications of Lag-Luminosity Relationship for Unified GRB Paradigms

Spectral lags (tau(sub lag)) are deduced for 1437 long (T(sub 90) greater than 2 s) BATSE gamma-ray bursts (GRBs) with peak flux F(sub p) greater than 0.25 photons cm(sup -2)/s, near to the BATSE trigger threshold. The lags are modeled to approximate the observed distribution in the F(sub p)-T(sub lag) plane, realizing a noise-free representation. Assuming a two-branch lag-luminosity relationship, the lags are self-consistently corrected for cosmological effects to yield distributions in luminosity, distance, and redshift. The results have several consequences for GRB populations and for unified gamma-ray/afterglow scenarios which would account for afterglow break times and gamma-ray spectral evolution in terms of jet opening angle, viewing angle, or a profiled jet with variable Lorentz factor: A component of the burst sample is identified - those with few, wide pulses, lags of a few tenths to several seconds, and soft spectra - whose Log[N]-Log[F(sub p)] distribution approximates a -3/2 power-law, suggesting homogeneity and thus relatively nearby sources. The proportion of these long-lag bursts increases from negligible among bright BATSE bursts to approx. 50% at trigger threshold. Bursts with very long lags, approx. 1-2 less than tau(sub lag) (S) less than 10, show a tendency to concentrate near the Supergalactic Plane with a quadrupole moment of approx. -0.10 +/- 0.04. GRB 980425 (SN 1998bw) is a member of this subsample of approx. 90 bursts with estimated distances less than 100 Mpc. The frequency of the observed ultra-low luminosity bursts is approx. 1/4 that of SNe Ib/c within the same volume. If truly nearby, the core-collapse events associated with these GRBs might produce gravitational radiation detectable by LIGO-II. Such nearby bursts might also help explain flattening of the cosmic ray spectrum at ultra-high energies, as observed by AGASA.

Norris, J. P.↗

Rb-Sr and Sm-Nd Isotopic Studies of Shergottite Y980459 and a Petrogenetic Link Between Depleted Shergottites and Nakhlites

Y980459 was found near the Minami-Yamato Nunataks, Antarctica in 1998 and was recently classified as an olivine-bearing shergottite. It petrographically resembles many other olivine-phyric shergottites mostly found in hot deserts, e.g. DaG476/489, SaU005/094, Dohfar 019, NWA 1068/1110, NWA 1195 and EETA 79001 lith.A. However, Y980459 is unique among these meteorites in several respects. It is apparently very fresh and only weakly shocked. Also, it completely lacks plagioclase, but contains abundant residual volcanic glass. This group of olivine-phyric shergottites is characterized by variable crystallization ages from approx.172 Ma to approx.575 Ma and ejection ages from approx.1 Ma to approx.20 Ma. They probably represent volcanic melts originated from the deep Martian mantle. We performed Rb-Sr and Sm-Nd isotopic analyses on Y980459 to determine its crystallization age and compared its age and isotopic signatures with those obtained from other olivine-phyric shergottites and QUE 94201, the other Antarctic olivine-free shergottite. QUE 94201 and some olivine-phyric shergottites e.g. DaG, SaU, Doh and EETA lith A have similar depleted-LREE patterns and are herein referred to as depleted shergottites. A petrogenetic model correlating depleted shergottites and nakhlites is also proposed. Preliminary Rb-Sr and Sm-Nd isotopic data for Y980459 were presented earlier at the NIPR, Japan, in 2003.

Shih, C.-Y.↗

Impact Forces From Artificial and Real Birds on a Large Diameter Hopkinson Bar

Forces were measured from normal impacts with two different artificial bird recipes and two species of real birds on a very rigid flat surface. The tests were conducted by launching the soft body projectiles axially into a Hopkinson bar in accordance with the SAE AS6940 test standard at three different nominal impact conditions: (a) a 1 kg projectile at an impact velocity of 49 m/sec; (b) a 1.8 kg projectile at an impact velocity of 110 m/sec; and (c) a 1.8 kg projectile at an impact velocity of 310 m/sec. At each condition two artificial birds and one real bird projectile were tested with at least three test repeats. Simulations were conducted to assess the effects of projectile orientation and velocity on predicted forces. The Hopkinson bar consisted of an Aluminum 6061 solid cylindrical bar with a diameter of 305 mm and a length of 7.31 m, made up of two 3.66 m long sections that were in axial contact with each other. The bar was instrumented for strain measurement at two locations, 457.2 mm and 609.6 mm (1.5 and 2 diameters) from the impacted face. Forces were calculated from the measured strain. In addition, digital image correlation (DIC) was used to measure the velocity of the free end of the bar. The real bird projectiles were 1 kg Mallard ducks and 1.8 kg Golden Comet chickens that were prepared per ASTM F330-21. Prior to testing, the real birds were placed in muslin bags to minimize tumbling during flight. Two artificial bird formulations were tested, one produced by the University of Dayton Research Institute (UDRI) and the other by the German Aerospace Center, DLR. The UDRI projectile was a homogeneous, relatively soft solid, formulated with a mixture of water, gelatin and phenolic micro-balloons to achieve a nominal density of 0.95 g/cc. The DLR projectile consisted of a printed plastic shell with internal plastic ribs and filled with a gel material. The projectiles were designed such that the overall average density was the desired value of 0.95 g/cc. Initial testing showed that contact between the two Hopkinson bar segments was not sufficient to allow full transmission of the waves through the interface. For the 49 m/sec and 110 m/sec tests this resulted in reflections returning to the strain measurement site prior to the end of the impact. For these tests only a portion of the force pulse could be accurately measured. For the highest velocity tests at 310 m/sec the force pulse was complete by the time reflected waves interfered with the response. Despite this limitation, useful force data were obtained for all velocities. Impact forces were very sensitive to the impact orientation and velocity. The force history generally consisted of an initial region with varying amplitude followed by a relatively constant amplitude response. The steady state region was similar among all projectiles and similar to what would be predicted for an inviscid fluid with a density of 0.95 g/cc. The initial part of the force response exhibited varying degrees of test-to-test repeatability associated with each projectile type. Forces calculated from DIC velocity measurements of the free end of the bar compared favorably those from the strain measurements. In general, the artificial projectile impact forces were quite repeatable from test to test, with some exceptions which could be explained by issues associated with either the projectile itself or with how the projectile exited the gun barrel. For all impact velocities the initial portion of the impact force from the bird projectiles exhibited large test-to-test variability. In this paper, impact forces for three types of projectiles at three impact velocities will be presented with an emphasis on the test-to-test repeatability of the results. Based on test and simulation results a proposed method for normalizing the impact force to minimize effects of differences in projectile orientation, impact velocity and density will also be discussed.

Bird strike↗

Performance and Application of FEL and PXR Sources at Nihon University

The infrared free electron laser (FEL) and the parametric X-ray radiation (PXR) developed on the basis of the 125 MeV electron linac at Nihon University have been applied to studies in a variety of scientific fields. Primary users so far are the faculty members in the university, approximately 2000 hr/year of the machine time having been dedicated to the experiments since 2004. Currently the wavelength range of the FEL served for users' experiments covers 1500 to 6000 nm at the optical power level of 10 to 30 mJ/macropulse. Combination of the fundamental infrared FEL with BBO non-linear optical crystals yielded higher harmonics with good conversion efficiencies, which has extended the available wavelength range as short as approximately 400 nm. The PXR generator has employed a double-crystal system so that the monochromatic X-ray beam is available at a fixed output port independently of the X-ray center energy. By using a Si(111) crystal as the PXR target the energy variable monochromatic X-ray beam from 5 to 20 keV has been successfully applied to users' experiments. The latest work on the PXR generation using a Si(220) target crystal has demonstrated availability of the X-ray beam with energies up to approximately 34 keV.

43 PARTICLE ACCELERATORS↗

Satellite Mapping of PM2.5 Episodes in the Wintertime San Joaquin Valley: A "Static" Model Using Column Water Vapor

The use of satellite Aerosol Optical Thickness (AOT) from imaging spectrometers has been successful in quantifying and mapping high PM2.5 (particulate matter mass <2.5µm diameter) episodes for pollution abatement and health studies. However, some regions have high PM2.5 but poor estimation success. The challenges in using Aerosol Optical Thickness (AOT) from imaging spectrometers to characterize PM2.5 worldwide was especially evident in the wintertime San Joaquin Valley (SJV). The SJV's attendant difficulties of high-albedo surfaces and very shallow, variable vertical mixing also occur in other significantly polluted regions around the world. We report on more accurate PM2.5 maps for the whole-winter period in the SJV, Nov 14, 2012?Dec 11, 2013. Intensive measurements by including NASA aircraft were made for several weeks in that winter, the DISCOVER-AQ California mission.We found success with a relatively simple method based on calibration and checking with surface monitors and a characterization of vertical mixing, and incorporating specific understandings of the region's climatology. We estimate PM2.5 to within ~7µgm?3 RMSE and with R values of ~0.9, based on remotely sensed MAIAC (Multi-Angle Implementation of Atmospheric Correction) observations, and that certain further work will improve that accuracy. Mapping is at 1km resolution. This allows a time sequence of mapped aerosols at 1km for cloud-free days. We describe our technique as a "static estimation". Estimation procedures like this one, not dependent on well-mapped source strengths or on transport error, should help full source-driven simulations by deconstructing processes. They also provide a rapid method to create a long-term climatology.Essential features of the technique are (a) daily calibration of the AOT to PM2.5 using available surface monitors, and (b) characterization of mixed-layer dilution using column water vapor (CWV, otherwise "precipitable water"). We noted that on multi-day timescales both water vapor and particles share near-surface sources and both fall to very low values with altitude; indeed, both are largely removed by precipitation. The existence of layers of H2O or aerosol not within the mixed layer adds complexity, but mixed-effects statistical regression captures essential proportionality of PM2.5 and the ratio variable (AOT/CWV). Accuracy is much higher than previous statistical models, and can be extended to the whole Aqua-satellite data record. The maps and time-series we show suggest a repeated pattern for large valleys like the SJV ? progressive stabilization of the mixing height after frontal passages: PM2.5 is somewhat more determined by day-by-day changes in mixing than it is by the progressive accumulation of pollutants (revealed as increasing AOT).

Chatfield, Robert B.↗

A score-based diffusion model approach for adaptive learning of stochastic partial differential equation solutions

In this paper, we propose a novel framework for adaptively learning the time-evolving solutions of stochastic partial differential equations (SPDEs) using score-based diffusion models within a recursive Bayesian inference setting. SPDEs play a central role in modeling complex physical systems under uncertainty, but their numerical solutions often suffer from model errors and reduced accuracy due to incomplete physical knowledge and environmental variability. To address these challenges, we encode the governing physics into the score function of a diffusion model using simulation data and incorporate observational information via a likelihood-based correction in a reverse-time stochastic differential equation. This enables adaptive learning through iterative refinement of the solution as new data becomes available. To improve computational efficiency in high-dimensional settings, we introduce the ensemble score filter, a training-free approximation of the score function designed for real-time inference. Numerical experiments on benchmark SPDEs demonstrate the accuracy and robustness of the proposed method under sparse and noisy observations.

97 MATHEMATICS AND COMPUTING↗

Anaerobic digestion of organic fraction of municipal solid waste combining two pretreatment modalities, high temperature microwave and hydrogen peroxide

Highlights: Black-Right-Pointing-Pointer Microwave and H{sub 2}O{sub 2} pretreatment were studied to enhance anaerobic digestion of organic waste. Black-Right-Pointing-Pointer The whole waste pretreated at 115 Degree-Sign C or 145 Degree-Sign C had the highest biogas production. Black-Right-Pointing-Pointer Biogas production of the whole waste decreased at 175 Degree-Sign C due to formation of refractory compounds. Black-Right-Pointing-Pointer Pretreatment to 145 Degree-Sign C and 175 Degree-Sign C were the best when considering only the free liquid fraction. Black-Right-Pointing-Pointer H{sub 2}O{sub 2} pretreatment had a lag phase and the biogas production was not higher than MW pretreated samples. - Abstract: In order to enhance anaerobic digestion (AD) of the organic fraction of municipal solid waste (OFMSW), pretreatment combining two modalities, microwave (MW) heating in presence or absence of hydrogen peroxide (H{sub 2}O{sub 2}) were investigated. The main pretreatment variables affecting the characteristics of the OFMSW were temperature (T) via MW irradiation and supplemental water additions of 20% and 30% (SWA20 and SW30). Subsequently, the focus of this study was to evaluate mesophilic batch AD performance in terms of biogas production, as well as changes in the characteristics of the OFMSW post digestion. A high MW induced temperature range (115-175 Degree-Sign C) was applied, using sealed vessels and a bench scale MW unit equipped with temperature and pressure controls. Biochemical methane potential (BMP) tests were conducted on the whole OFMSW as well as the liquid fractions. The whole OFMSW pretreated at 115 Degree-Sign C and 145 Degree-Sign C showed 4-7% improvement in biogas production over untreated OFMSW (control). When pretreated at 175 Degree-Sign C, biogas production decreased due to formation of refractory compounds, inhibiting the digestion. For the liquid fraction of OFMSW, the effect of pretreatment on the cumulative biogas production (CBP) was more pronounced for SWA20 at 145 Degree-Sign C, with a 26% increase in biogas production after 8 days of digestion, compared to the control. When considering the increased substrate availability in the liquid fraction after MW pretreatment, a 78% improvement in biogas production vs. the control was achieved. Combining MW and H{sub 2}O{sub 2} modalities did not have a positive impact on OFMSW stabilization and enhanced biogas production. In general, all samples pretreated with H{sub 2}O{sub 2} displayed a long lag phase and the CBP was usually lower than MW irradiated only samples. First order rate constant was calculated.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

SU-F-R-31: Identification of Robust Normal Lung CT Texture Features for the Prediction of Radiation-Induced Lung Disease

Purpose: Normal lung CT texture features have been used for the prediction of radiation-induced lung disease (radiation pneumonitis and radiation fibrosis). For these features to be clinically useful, they need to be relatively invariant (robust) to tumor size and not correlated with normal lung volume. Methods: The free-breathing CTs of 14 lung SBRT patients were studied. Different sizes of GTVs were simulated with spheres placed at the upper lobe and lower lobe respectively in the normal lung (contralateral to tumor). 27 texture features (9 from intensity histogram, 8 from grey-level co-occurrence matrix [GLCM] and 10 from grey-level run-length matrix [GLRM]) were extracted from [normal lung-GTV]. To measure the variability of a feature F, the relative difference D=|Fref -Fsim|/Fref*100% was calculated, where Fref was for the entire normal lung and Fsim was for [normal lung-GTV]. A feature was considered as robust if the largest non-outlier (Q3+1.5*IQR) D was less than 5%, and considered as not correlated with normal lung volume when their Pearson correlation was lower than 0.50. Results: Only 11 features were robust. All first-order intensity-histogram features (mean, max, etc.) were robust, while most higher-order features (skewness, kurtosis, etc.) were unrobust. Only two of the GLCM and four of the GLRM features were robust. Larger GTV resulted greater feature variation, this was particularly true for unrobust features. All robust features were not correlated with normal lung volume while three unrobust features showed high correlation. Excessive variations were observed in two low grey-level run features and were later identified to be from one patient with local lung diseases (atelectasis) in the normal lung. There was no dependence on GTV location. Conclusion: We identified 11 robust normal lung CT texture features that can be further examined for the prediction of radiation-induced lung disease. Interestingly, low grey-level run features identified normal lung diseases. This work was supported in part by the National Cancer Institute Grants R01CA172638.

60 APPLIED LIFE SCIENCES↗