Search NASA⌕ Search

SEARCH · Search NASA

Results for “vortex generators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

1,629 records · Page 91

Fundamental Study of a Single Point Lean Direct Injector. Part I: Effect of Air Swirler Angle and Injector Tip Location on Spray Characteristics

Lean direct injection (LDI) is a combustion concept to reduce oxides of nitrogen (NOx) for next generation aircraft gas turbine engines. These newer engines have cycles that increase fuel efficiency through increased operating pressures, which increase combustor inlet temperatures. NOx formation rates increase with higher temperatures; the LDI strategy avoids high temperature by staying fuel lean and away from stoichiometric burning. Thus, LDI relies on rapid and uniform fuel/air mixing. To understand this mixing process, a series of fundamental experiments are underway in the Combustion and Dynamics Facility at NASA Glenn Research Center. This first set of experiments examines cold flow (non-combusting) mixing using air and water. Using laser diagnostics, the effects of air swirler angle and injector tip location on the spray distribution, recirculation zone, and droplet size distribution are examined. Of the three swirler angles examined, 60 degrees is determined to have the most even spray distribution. The injector tip location primarily shifts the flow without changing the structure, unless the flow includes a recirculation zone. When a recirculation zone is present, minimum axial velocity decreases as the injector tip moves downstream towards the venturi exit; also the droplets become more uniform in size and angular distribution.

vortex↗

Mechanisms of Dynamic Near-Wake Modulation of a Utility-Scale Wind Turbine

The current study uses large eddy simulations to investigate the transient response of a utility-scale wind turbine wake to dynamic changes in atmospheric and operational conditions, as observed in previous field-scale measurements. Most wind turbine wake investigations assume quasi-steady conditions, but real wind turbines operate in a highly stochastic atmosphere, and their operation (e.g. blade pitch, yaw angle) changes constantly in response. Furthermore, dynamic control strategies have been recently proposed to optimize wind farm power generation and longevity. Therefore, improved understanding of dynamic wake behaviours is essential. First, changes in blade pitch are investigated and the wake expansion response is found to display hysteresis as a result of flow inertia. The time scales of the wake response to different pitch rates are quantified. Next, changes in wind direction with different time scales are explored. Under short time scales, the wake deflection is in the opposite direction of that observed under quasi-steady conditions. Finally, yaw changes are implemented at different rates, and the maximum inverse wake deflection and time scale are quantified, showing a clear dependence on yaw rate. To gain further physical understanding of the mechanism behind the inverse wake deflection, the streamwise vorticity in different parts of the wake is quantified. The results of this study provide guidance for the design of advanced wake flow control algorithms. The lag in wake response observed for both blade pitch and yaw changes shows that proposed dynamic control strategies must implement turbine operational changes with a time scale of the order of the rotor time scale or slower.

flow-structure interactions↗

Reducing uncertainty of polar to midlatitude linkages using DOE’s E3SM in a coordinated model-experiment setting

This project brought DOE’s climate modeling effort with the Energy Exascale Earth System Model into the Polar Amplification Model Intercomparison Project (PAMIP), which is part of the sixth and latest Coupled Model Intercomparison Project, CMIP6. PAMIP examines the causes and consequences of polar amplification, when external forcing results in a larger temperature increase in high latitudes than the global average, in a coordinated set of model experiments with a common modeling protocol. Our teams from UC Irvine and the University of Toronto have designed, carried out, analyzed, and disseminated PAMIP output from the Energy Exascale Earth System Model (E3SM) and the Community Earth System Model (CESM). PAMIP’s ongoing stream of significant new results have advanced progress in the community’s understanding and led to new outstanding research questions that have motivated further work. PAMIP has led to improved consensus on the atmospheric response to sea ice loss. The important finding is that for a similar sea ice anomaly forcing, the simulated atmospheric response in the troposphere is remarkably consistent among the 16 models’ runs analyzed. The zonal-mean tropospheric response consists of a very robust equatorward shift of the westerly flow in mid-latitudes. However, while the multi-model mean response is robust, it has a weak amplitude relative to internal variability. We identified a weakness in the models (including E3SM) in terms of their response to sea-ice forcing that is related to eddy forcing (or nonlinear dynamical effects) at mid- to high latitudes. In fact, E3SM is an outlier in terms of the models participating, and in that sense, it turned out to be a vital participant model. We found that reductions in energy transport due sea-ice loss and involving dry air only are compensated by increases in moist energy transport from warmer sea surface temperature in midlatitudes. This leads to a large spread in energy transport into the Arctic and is a potential source of spread in Arctic amplification. We identified an important role that climate modes, including tropical modes of variability (El Nino and the Southern Oscillation (ENSO); the Quasi-biennial Oscillation (QBO)) play in the response to sea-ice anomalies, including in ocean coupled experiments. Similarly, we identified and quantified the contribution of sea-ice thickness to the atmospheric response compared to the response to sea-ice extent only. We found that it is important to run large ensembles and even with an ensemble size of 100 simulations the response is largely influenced by internal variability. We demonstrated convincingly that Ural blocking, not sea-ice loss, provides the weakening of the stratospheric polar vortex in fall/early winter and a negative phase of the North Atlantic Oscillation that can last for up to two months. However, sea-ice anomalies can influence the background flow so that the response to Ural blocking is more persistent under low sea-ice conditions in the Barents/Kara Sea than high sea ice Atmospheric model hierarchies that progressively add individual processes have a long history in providing dynamical insight for modeling the atmosphere. Similarly, coupled model hierarchies that progressively add individual ocean processes can provide insights into the workings of the coupled climate system, however such hierarchies have not been available except for a non-dynamical slab ocean model. Because of the missing processes, surface flux corrections must be added to produce a target climate. In this project, we managed to overcome this problem and develop a globally coupled ocean model hierarchy in CESM that can turn on and off the processes of mixed-layer entrainment and Ekman flow. We used the hierarchy to study the impact of Arctic sea-ice loss on the climate system. We find that the effect of mixed-layer entrainment on ocean heat uptake influences the atmospheric circulation by shifting the latitudinal positions of the mid-latitude westerly jet and the Intertropical Convergence Zone (ITCZ). In quadrupled CO 2 experiments, we studied how air-sea coupling affects the response of tropical rainfall under global warming. In order to identify the importance of individual ocean processes, we used the hierarchy of ocean models to separate the effects of seasonal mixed-layer entrainment, wind-driven Ekman flows, and frictional flows. We showed that including Ekman and frictional flows allows our simulation to produce the Pacific Ocean's enhanced equatorial warming pattern and equatorward ITCZ contraction noted in previous climate simulations. We also showed that the frictional flow, which has yet to receive much attention, is as important as the Ekman flow in generating equatorial heat convergence.

54 ENVIRONMENTAL SCIENCES↗

Turbulent heat transfer enhancement by counter/co-swirling flow in a tube fitted with twin twisted tapes

In the present study, the influences of twin-counter/co-twisted tapes (counter/co-swirl tape) on heat transfer rate (Nu), friction factor (f) and thermal enhancement index ({eta}) are experimentally determined. The twin counter twisted tapes (CTs) are used as counter-swirl flow generators while twin co-twisted tapes (CoTs) are used as co-swirl flow generators in a test section. The tests are conducted using the CTs and CoTs with four different twist ratios (y/w = 2.5, 3.0, 3.5 and 4.0) for Reynolds numbers range between 3700 and 21,000 under uniform heat flux conditions. The experiments using the single twisted tape (ST) are also performed under similar operation test conditions, for comparison. The experimental results demonstrate that Nusselt number (Nu), friction factor (f) and thermal enhancement index ({eta}) increase with decreasing twist ratio (y/w). The results also show that the CTs are more efficient than the CoTs for heat transfer enhancement. In the range of the present work, heat transfer rates in the tube fitted with the CTs are around 12.5-44.5% and 17.8-50% higher than those with the CoTs and ST, respectively. The maximum thermal enhancement indices ({eta}) obtained at the constant pumping power by the CTs with y/w = 2.5, 3.0, 3.5 and 4.0, are 1.39, 1.24, 1.12 and 1.03, respectively, while those obtained by using the CoTs with the same range of y/w are 1.1, 1.03, 0.97 and 0.92, respectively. In addition, the empirical correlations of the heat transfer (Nu), friction factor (f) and thermal enhancement index ({eta}) are also reported. (author)

42 ENGINEERING↗

Going beyond BEM with BEM: an insight into dynamic inflow effects on floating wind turbines

Blade element momentum (BEM) theory is the backbone of many industry-standard wind turbine aerodynamic models. To be applied to a broader set of engineering problems, BEM models have been extended since their inception and now include several empirical corrections. These models have benefitted from decades of development and refinement and have been extensively used and validated, proving their adequacy in predicting aerodynamic forces of horizontal-axis wind turbine rotors in most scenarios. However, the analysis of floating offshore wind turbines (FOWTs) introduces new sets of challenges, especially if new-generation large and flexible machines are considered. In fact, due to the combined action of wind and waves and their interaction with the turbine structure and control system, these machines are subject to unsteady motion and thus unsteady inflow on the wind turbine's blades, which could put BEM models to the test. Consensus has not been reached on the accuracy limits of BEM in these conditions. This study contributes to the ongoing research on the topic by systematically comparing four different aerodynamic models, ranging from BEM to computational fluid dynamics, in an attempt to shed light on the unsteady aerodynamic phenomena that are at stake in FOWTs and whether BEM is able to model them appropriately. Simulations are performed on the UNAFLOW 1:75 scale rotor during imposed harmonic surge and pitch motion. Experimental results are available for these conditions and are used for baseline validation. The rotor is analyzed in both rated operating conditions and low wind speeds, where unsteady aerodynamic effects are expected to be more pronounced. Results show that BEM, despite its simplicity, can adequately model the aerodynamics of FOWTs in most conditions if augmented with a dynamic inflow model.

17 WIND ENERGY↗

A Numerical Study of Hurricane Erin (2001): Model Verification and Storm Evolution - Part 1

The fifth-generation Pennsylvania State University National Center for Atmospheric Research (PSU NCAR) Mesoscale Model (MM5) is used to simulate Hurricane Erin (2001) at high resolution (4-km spacing) from its early development as a tropical depression on 7 September 2001, through a period of rapid intensification into a strong hurricane (8 9 September), and finally into a stage during which it maintains its intensity on 10 September. These three stages of formation, intensification, and maintenance in the simulation are in good agreement with the observed evolution of Erin. The simulation shows that during the formation and early portions of the intensification stages, intensification is favored because the environmental wind shear is weak and the system moves over a warm tongue of water. As Erin intensifies, the wind shear gradually increases with the approach of an upper-level trough and strengthening of a low-level high pressure system. By 10 September, the wind shear peaks and begins to decrease, the storm moves over slightly cooler waters, and the intensification ends. Important structural changes occur at this time as the outer precipitation shifts from the northeastern and eastern sides to the western side of the eye. A secondary wind maximum and an outer eyewall begin to develop as precipitation begins to surround the entire eye. The simulation is used to investigate the role of vertical wind shear in the changes of the precipitation structure that took place between 9 and 10 September by examining the effects of changes in storm-relative flow and changes in the shear-induced tilt. Qualitative agreement is found between the divergence pattern and advection of vorticity by the relative flow with convergence (divergence) generally associated with asymmetric inflow (outflow) in the eyewall region. The shift in the outer precipitation is consistent with a shift in the low-level relative inflow from the northeastern to the northwestern side of the storm. The changes in the relative flow are associated with changes in the environmental winds as the hurricane moves relative to the upper trough and the low-level high pressure system. Examination of the shear-induced tilt of the vortex shows that the change in the tilt direction is greater than that of the shear direction as the tilt shifts from a northerly orientation to northwesterly. Consistent with theory for adiabatic vortices, the maximum low-level convergence and upper-level divergence (and the maximum upward motion) occurs in the direction of tilt. Consequently, both mechanisms may play roles in the changes in the precipitation pattern.

Wu, Liguang↗

Experimental Investigation of Turbine Vane Heat Transfer for Alternative Fuels

The focus of this program was to experimentally investigate advanced gas turbine cooling schemes and the effects of and factors that contribute to surface deposition from particulate matter found in coal syngas exhaust flows on turbine airfoil heat transfer and film cooling, as well as to characterize surface roughness and determine the effects of surface deposition on turbine components. The program was a comprehensive, multi-disciplinary collaborative effort between aero-thermal and materials faculty researchers and the Department of Energy, National Energy Technology Laboratory (NETL). The primary technical objectives of the program were to evaluate the effects of combustion of syngas fuels on heat transfer to turbine vanes and blades in land-based power generation gas turbine engines. The primary questions to be answered by this investigation were; What are the factors that contribute to particulate deposition on film cooled gas turbine components? An experimental program was performed in a high-temperature and pressure combustion rig at the DOE NETL; What is the effect of coal syngas combustion and surface deposition on turbine airfoil film cooling? Deposition of particulate matter from the combustion gases can block film cooling holes, decreasing the flow of the film coolant and the film cooling effectiveness; How does surface deposition from coal syngas combustion affect turbine surface roughness? Increased surface roughness can increase aerodynamic losses and result in decreased turbine hot section efficiency, increasing engine fuel consumption to maintain desired power output. Convective heat transfer is also greatly affected by the surface roughness of the airfoil surface; Is there any significant effect of surface deposition or erosion on integrity of turbine airfoil thermal barrier coatings (TBC) and do surface deposits react with the TBC in any way to decrease its thermal insulating capability? Spallation and erosion of TBC is a persistent problem in modern turbine engines; and What advancements in film cooling hole geometry and design can increase effectiveness of film cooling in turbines burning high-hydrogen coal syngas due to the higher heat loads and mass flow rates of the core flow? Experimental and numerical investigations of advanced cooling geometries that can improve resistance to surface deposition were performed. The answers to these questions were investigated through experimental measurements of turbine blade surface temperature and coolant coverage (via infrared camera images and thermocouples) and time-varying surface roughness in the NETL high-pressure combustion rig with accelerated, simulated surface deposition and advanced cooling hole concepts, coupled with detailed materials analysis and characterization using conventional methods of Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), X-Ray Diffraction (XRD), 3-D Surface Topography (using a 3-D stylus profilometer). Detailed surface temperatures and cooling effectiveness could not be measured due to issues with the NETL infrared camera system. In collaboration with faculty startup funding from the principal investigator, experimental and numerical investigations were performed of an advanced film cooling hole geometry, the anti-vortex hole (AVH), focusing on improving cooling effectiveness and decreasing the counter-rotating vortex of conventional cooling holes which can entrain mainstream particulate matter to the surface. The potential benefit of this program is in gaining a fundamental understanding of how the use of alternative fuels will effect the operation of modern gas turbine engines, providing valuable data for more effective cooling designs for future turbine systems utilizing alternative fuels.

10 SYNTHETIC FUELS↗

Experiments on the Richtmyer-Meshkov Instability of Incompressible Fluids

Richtmyer-Meshkov (R-M) instability occurs when two different density fluids are impulsively accelerated in the direction normal to their nearly planar interface. The instability causes small perturbations on the interface to grow and possibly become turbulent given the proper initial conditions. R-M instability is similar to the Rayleigh-Taylor (R-T) instability, which is generated when the two fluids undergo a constant acceleration. R-M instability is a fundamental fluid instability that is important to fields ranging from astrophysics to high-speed combustion. For example, R-M instability is currently the limiting factor in achieving a net positive yield with inertial confinement fusion. The experiments described here utilize a novel technique that circumvents many of the experimental difficulties previously limiting the study of the R-M instability. A Plexiglas tank contains two unequal density liquids and is gently oscillated horizontally to produce a controlled initial fluid interface shape. The tank is mounted to a sled on a high speed, low friction linear rail system, constraining the main motion to the vertical direction. The sled is released from an initial height and falls vertically until it bounces off of a movable spring, imparting an impulsive acceleration in the upward direction. As the sled travels up and down the rails, the spring retracts out of the way, allowing the instability to evolve in free-fall until impacting a shock absorber at the end of the rails. The impulsive acceleration provided to the system is measured by a piezoelectric accelerometer mounted on the tank, and a capacitive accelerometer measures the low-level drag of the bearings. Planar Laser-Induced Fluorescence is used for flow visualization, which uses an Argon ion laser to illuminate the flow and a CCD camera, mounted to the sled, to capture images of the interface. This experimental study investigates the instability of an interface between incompressible, miscible liquids with an initial sinusoidal perturbation. The amplitude of the disturbance during the experiment is measured and compared to theory. The results show good agreement (within 10%) with linear stability theory up to nondimensional amplitude ka = 0.7 (wavenumber x amplitude). These results hold true for an initial ka (before acceleration) of -0.7 less than ka less than -0.06, while the linear theory was developed for absolute value of ka much less than 1. In addition, a third order weakly nonlinear perturbation theory is shown to be accurate for amplitudes as large as ka = 1.3, even though the interface becomes double-valued at ka = 1.1. As time progresses, the vorticity on the interface concentrates, and the interface spirals around the alternating sign vortex centers to form a mushroom pattern. At higher Reynolds Number (based on circulation), an instability of the vortex cores has been observed. While time limitations of the apparatus prevent determination of a critical Reynolds Number, the lowest Reynolds Number this vortex instability has been observed at is 5000.

Jacobs, J.↗

Model fusion with physics-guided machine learning: Projection-based reduced-order modeling

The unprecedented amount of data generated from experiments, field observations, and large-scale numerical simulations at a wide range of spatiotemporal scales has enabled the rapid advancement of data-driven and especially deep learning models in the field of fluid mechanics. Although these methods are proven successful for many applications, there is a grand challenge of improving their generalizability. This is particularly essential when data-driven models are employed within outer-loop applications like optimization. In this work, we put forth a physics-guided machine learning (PGML) framework that leverages the interpretable physics-based model with a deep learning model. Leveraging a concatenated neural network design from multi-modal data sources, the PGML framework is capable of enhancing the generalizability of data-driven models and effectively protects against or inform about the inaccurate predictions resulting from extrapolation. We apply the PGML framework as a novel model fusion approach combining the physics-based Galerkin projection model and long- to short-term memory (LSTM) network for parametric model order reduction of fluid flows. We demonstrate the improved generalizability of the PGML framework against a purely data-driven approach through the injection of physics features into intermediate LSTM layers. Our quantitative analysis shows that the overall model uncertainty can be reduced through the PGML approach, especially for test data coming from a distribution different than the training data. Moreover, we demonstrate that our approach can be used as an inverse diagnostic tool providing a confidence score associated with models and observations. The proposed framework also allows for multi-fidelity computing by making use of low-fidelity models in the online deployment of quantified data-driven models.

42 ENGINEERING↗