SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A network of 8 or more precision transponder units mounted on the sea floor and interrogated periodically from an instrument package towed near bottom through the area to provide the necessary spatial averaging could provide a practical system for observing the pattern of buildup of strain at intermediate and fast spreading centers.
As the Apollo program proceeded, redundancy became a requirement for all crew safety functions. One critical period of the Apollo missions was the rendezvous of the Command Module and the Lunar Module. The rendezvous radar provided the critical range, range rate, and angle measurements necessary to complete the rendezvous. Use of a redundant radar for backup was out of the question because of its 80-lb weight. It was, however, found that the voice radios could be adapted to perform the ranging function. Slight modifications of the VHF voice radios and the addition of a ranging interrogator and transponder at a weight of less than 10 lbs total would provide an accuracy of 100-ft rms at several hundred miles. The Apollo VHF ranging system demonstrated that it is feasible to achieve highly accurate range measurements with conventional voice radios.
Experiments at the Arc Jet Tunnel at Ames Research Center have typical run times of 5-10 sec during which the test model is subjected to an environment simulating reentry into Jupiter. Previous real-time determination of mass flow required off-line manual computations from taped or strip chart data. The present paper describes a computer which provides personnel with real-time computations of mass flow. Using an 8-bit microprocessor and standard TTL interface circuitry, the unit interrogates temperature and pressure instruments with other parameters to compute mass flow.
Twelve hundred days of 3-6 keV X-ray data from Her X-1, Vela X-1, and Cen X-3 accumulated with the Ariel 5 All-Sky Monitor are interrogated. The binary periodicities of all three can be clearly observed, as can the 35 day variation of Her X-1, for which we can refine the period to 34.875 plus or minus 0.030 days. No such longer-term periodicity less than 200 days is observed from Vela X-1. The 26.6 days low-state recurrence period for Cen X-3 is not observed, but a 43.0 day candidate periodicity is found which may be consistent with the precession of an accretion disk in that system. The present results are illustrative of the long-term studies which can be performed on approximately 50 sources over a temporal base which will ultimately extend to at least 1800 days.
Report describes small test set which interrogates solar-energy data acquisition systems. Lightweight, portable set includes microcomputer with keyboard, alphanumeric display, printer, cassette recorder/player for storing programs and data, and cable for connection to Site Data Acquisition System (SDAS). Unit is operated by BASIC program and Assembly language. Report is specific to DOE/NASA application yet contains general information to assist in designing similar units.
The DOD and NASA inertial upper stage communication system design, hardware specifications and interfaces were analyzed to determine their compatibility with the Orbiter payload communications equipment (Payload Interrogator, Payload Signal Processors, Communications Interface Unit, and the Orbiter operational communications equipment (the S-Band and Ku-band systems). Topics covered include (1) IUS/shuttle Orbiter communications interface definition; (2) Orbiter avionics equipment serving the IUS; (3) IUS communication equipment; (4) IUS/shuttle Orbiter RF links; (5) STDN/TDRS S-band related activities; and (6) communication interface unit/Orbiter interface issues. A test requirement plan overview is included.
The analysis of the design, and the performance assessment of the Orbiter S-band communication equipment are reported. The equipment considered include: network transponder, network signal processor, FM transmitter, FM signal processor, payload interrogator, and payload signal processor.
JPL image processing applications are examined, considering future trends in fields such as planetary exploration, electronics, astronomy, computers, and Landsat. Attention is given to adaptive search and interrogation of large image data bases, the display of multispectral imagery recorded in many spectral channels, merging data acquired by a variety of sensors, and developing custom large scale integrated chips for high speed intelligent image processing user stations and future pipeline production processors.
The results of noise measurements and calculations are available in the form of noise maps for each of the three areas. To measure the stress due to airplane noise the Noise and Number Index (NNI) was applied. In the vicinities of the airports, 400 households were randomly selected in each of the three noise zones (of 10 NNI intervals each). A total of 3939 questionnaires could be evaluated, one quarter of which came from areas without airplane noise. Concurrently, traffic noise was measured in areas of Basel and expressed in sum total levels L sub 50 and the reaction of 944 persons was elicited by interrogation.
Position surveillance using one active ranging/communication satellite and the time-of-arrival of signals from an independent satellite was shown to be feasible and practical. A towboat on the Mississippi River was equipped with a tone-code ranging transponder and a receiver tuned to the timing signals of the GOES satellite. A similar transponder was located at the office of the towing company. Tone-code ranging interrogations were transmitted from the General Electric Earth Station Laboratory through ATS-6 to the towboat and to the ground truth transponder office. Their automatic responses included digital transmissions of time-of-arrival measurements derived from the GOES signals. The Earth Station Laboratory determined ranges from the satellites to the towboat and computed position fixes. The ATS-6 lines-of-position were more precise than 0.1 NMi, 1 sigma, and the GOES lines-of-position were more precise than 1.6 NMi, 1 sigma. High quality voice communications were accomplished with the transponders using a nondirectional antenna on the towboat. The simple and effective surveillance technique merits further evaluation using operational maritime satellites.
Potential problems associated with interfacing payload elements with orbiter communications and data handling elements are identified. Elements include Ku-band signal processor (KuSP), payload signal processor (PSP), payload interrogator (PI), payload data interleaver (PDI) and payload recorder (PR).
The payload interrogator provides full duplex communication between the orbiter and detached payloads. This capability includes transmission of commands to and the reception of telemetry data from such payloads. Both NASA (STDN and DSN) and DOD (SGLS) transmit/receive frequency pairs are available. In addition to two way RF communication, Ku band rendezvous radar is also available. The radar skin-tracks targets in the passive mode or actively tracks transponder equipped payloads. Characteristics referring to those orbiter avionics characteristics of which the payloads must be cognizant and requirements referring to specifications placed upon payload communication equipment are discussed.
The application of passive hydrogen masers to satellites was investigated. The NRL maser is of compact design suitable for the space environment. It is based on a dielectrically loaded sapphire cavity and uses a computer optimized set of four shields. The servo design is a phase sensitive method which directly measures the phase dispersion of the interrogating signal as it passes through the cavity.
The strain sensitivity of an optical fiber interferometer developed for the detection of pulsed ultrasonic waves in solids has been calibrated. The optical paths in both signal and reference arms of the interferometer are through similar 2 m lengths of ITT-110 single mode fibers mode stripped by index matching at both ends and attached to opposite sides of a 30 cm plexiglas bar 0.3 cm thick. Light from the output ends of both fibers was superimposed to form an interference fringe pattern that was interrogated in the far field to give a signal proportional to the differential optical fiber path length. Strain sensitivity was determined by comparing data obtained by clamping and bending the bar at different lengths to simple cantilever beam theory. Calibration indicates a minimum theoretical detectable strain of less than 10 to the -10.
The strain sensitivity of an optical fiber interferometer developed for the detection of pulsed ultrasonic waves in solids was calibrated. Light from the output ends of both fibers was superimposed to form an interference fringe pattern that was interrogated in the far field to give a signal proportional to the differential optical fiber path length. Strain sensitivity is determined by comparing data obtained by clamping and bending the bar at different lengths to simple cantilever beam theory. A minimum theoretical detectable strain of less than 10 to the minus 10th power is indicated.
A transducer with a velocity profile which is Gaussian as a function of radius and independent of angle is described. In materials evaluation applications requiring the interrogation of modified far field patterns of an ultrasonic transducer, it is desirable to use a transducer which produces a beam with a Gaussian profile. A computer aided electrode design and calibrated three dimensional interferometric optical and ultrasonic measurements of the far field distribution are presented.
Calibrated masurements of acoustic surface wave pulses by wide bandwidth differential interferometry are described. By interrogating the interference pattern formed by superimposing two optical beams reflected from the surface at slightly separated points, an output signal proportional to instantaneous surface particle displacement is obtained. Response to ideal propagating step function displacements is analyzed and measurements of gated pulses are described.
Laser speckle velocimetry, the measurement of fluid velocity by measuring the translation of speckle pattern or individual particles that are moving with the fluid, is described. The measurement is accomplished by illuminating the fluid with consecutive pulses of Laser Light and recording the images of the particles or the speckles on a double exposed photographic plate. The plate contains flow information throughout the image plane so that a single double exposure may provide data at hundreds or thousands of points in the illuminated region of the fluid. Conventional interrogation of the specklegram involves illuminating the plate to form Young's fringes, whose spacing is inversely proportional to the speckle separation. Subsequently the fringes are digitized and analyzed in a computer to determine their frequency and orientation, yielding the velocity magnitude and orientation. The Young's fringe technique is equivalent to performing a 2-D spatial correlation of the double exposed specklegram intensity pattern, and this observation suggests that correlation should be considered as an alternative processing method. The principle of the correlation technique is examined.