Search NASA⌕ Search

SEARCH · Search NASA

Results for “PROCESS SOLUTIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

Surface Plasmon Enhanced Phosphorescent Organic Light Emitting Diodes

The objective of the proposed work was to develop the fundamental understanding and practical techniques for enhancement of Phosphorescent Organic Light Emitting Diodes (PhOLEDs) performance by utilizing radiative decay control technology. Briefly, the main technical goal is the acceleration of radiative recombination rate in organometallic triplet emitters by using the interaction with surface plasmon resonances in noble metal nanostructures. Increased photonic output will enable one to eliminate constraints imposed on PhOLED efficiency by triplet-triplet annihilation, triplet-polaron annihilation, and saturation of chromophores with long radiative decay times. Surface plasmon enhanced (SPE) PhOLEDs will operate more efficiently at high injection current densities and will be less prone to degradation mechanisms. Additionally, introduction of metal nanostructures into PhOLEDs may improve their performance due to the improvement of the charge transport through organic layers via multiple possible mechanisms ('electrical bridging' effects, doping-like phenomena, etc.). SPE PhOLED technology is particularly beneficial for solution-fabricated electrophosphorescent devices. Small transition moment of triplet emitters allows achieving a significant enhancement of the emission rate while keeping undesirable quenching processes introduced by the metal nanostructures at a reasonably low level. Plasmonic structures can be introduced easily into solution-fabricated PhOLEDs by blending and spin coating techniques and can be used for enhancement of performance in existing device architectures. This constitutes a significant benefit for a large scale fabrication of PhOLEDs, e.g. by roll-to-roll fabrication techniques. Besides multieexciton annihilation, the power efficacy of PhOLEDs is often limited by high operational bias voltages required for overcoming built-in potential barriers to injection and transport of electrical charges through a device. This problem is especially pronounced in solution processed OLEDs lacking the accuracy and precision of fabrication found in their small molecule counterparts. From this point of view, it seems beneficial to develop materials allowing reduction of the operation bias voltage via improvement of the charge injection. The materials sought have to be compatible with solution-based fabrication process and allow easy incorporation of metal nanostructures.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Photogrammetry Toolbox Reference Manual

Specialized photogrammetric and image processing MATLAB functions useful for wind tunnel and other ground-based testing of aerospace structures are described. These functions include single view and multi-view photogrammetric solutions, basic image processing to determine image coordinates, 2D and 3D coordinate transformations and least squares solutions, spatial and radiometric camera calibration, epipolar relations, and various supporting utility functions.

Liu, Tianshu↗

Interaction of a sodium ion with the water liquid-vapor interface

Molecular dynamics results are presented for the density profile of a sodium ion near the water liquid-vapor interface at 320 K. These results are compared with the predictions of a simple dielectric model for the interaction of a monovalent ion with this interface. The interfacial region described by the model profile is too narrow and the profile decreases too abruptly near the solution interface. Thus, the simple model does not provide a satisfactory description of the molecular dynamics results for ion positions within two molecular diameters from the solution interface where appreciable ion concentrations are observed. These results suggest that surfaces associated with dielectric models of ionic processes at aqueous solution interfaces should be located at least two molecular diameters inside the liquid phase. A free energy expense of about 2 kcal/mol is required to move the ion within two molecular layers of the free water liquid-vapor interface.

NASA Center ARC↗

Periodic Heat Transfer at Small Pressure Fluctuations

The effect of cyclic gas pressure variations on the periodic heat transfer at a flat wall is theoretically analyzed and the differential equation describing the process and its solution for relatively. Small pressure fluctuations developed, thus explaining the periodic heat cycle between gas and wall surface. The processes for pure harmonic pressure and temperature oscillations, respectively, in the gas space are described by means of a constant heat transfer coefficient and the equally constant phase angle between the appearance of the maximum values of the pressure and heat flow most conveniently expressed mathematically in the form of a complex heat transfer coefficient. Any cyclic pressure oscillations, can be reduced by Fourier analysis to harmonic oscillations, which result in specific, mutual relationships of heat-transfer coefficients and phase angles for the different harmonics.

Pfriem, H.↗

Direct Down-scale Experiments of Concentration Column Designs for SHINE Process

Argonne is assisting SHINE Medical Technologies in their efforts to become a domestic Mo-99 producer. The SHINE accelerator-driven process uses a uranyl-sulfate target solution for the production of fission-product Mo-99. Argonne has developed a molybdenum recovery and purification process for this target solution. The process includes an initial Mo recovery column followed by a concentration column to reduce the product volume from 15-25 L to < 1 L prior to entry into the LEU Modified Cintichem (LMC) process for purification.1 This report discusses direct down-scale experiments of the plant-scale concentration column design, where the effects of loading velocity and temperature were investigated.

42 ENGINEERING↗

Chemical Compensation Challenges in Processing Antiferroelectric PbZrO 3 Thin Films

The electric field-induced antipolar-to-polar phase transition in antiferroelectric materials is accompanied by large changes in the structural and functional response, making them attractive for many applications ranging from pulsed energy capacitors to high-strain-high (blocking-)force actuators, solid-state heating and cooling systems, and optoelectronic devices. PbZrO 3 , as an end member of the PZT, (x)PbZr 1–x Ti x O 3 , solid solution, has been the subject of many studies. However, processing of perovskite PbZrO 3 is extremely challenging due to phase instabilities induced by Pb loss at the temperatures necessary for perovskite crystallization. Here, we discuss the challenges associated with Pb loss, as well as its compensation through bulk Pb overstoichiometry and interfacial PbO additions, in chemical solution processed, highly oriented PbZrO 3 thin films. For both 042 o - and 001 o -oriented (o-orthorhombic distortion) PbZrO 3 thin films, the crystallization interfaces are the most important contributors to Pb loss and off-stoichiometric outcomes, and no single approach was sufficient to address these challenges. Pb-rich and Pb-deficient nonperovskite phases including ZrO x were only observable through microscopic characterization, and X-ray diffraction alone could not rule out the presence of such secondary phases. “Ideal” macroscopic antiferroelectric polarization-electric field double hysteresis curves were observed despite (at times) the large presence of secondary phases. However, reduced saturation polarization and increased phase transition electric fields were observed concomitantly with the presence of secondary phase(s) and tentatively assigned to the voltage drop across the ZrO x nanocrystals. Based on these results, it is imperative that the presence of secondary phases always be addressed (beyond X-ray diffraction spectra) in order to correctly evaluate the properties of antiferroelectric films.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Crystallization of Ammonium Heptamolybdate for Reduction to Mo Metal

The 100 Mo/ 98 Mo recycle process developed by Argonne National Laboratory in collaboration with Oak Ridge National Laboratory (ORNL) and supported by the U.S. Department of Energy (DOE) National Nuclear Security Agency’s (NNSA’s) Office of Material Management & Minimization (M3) is vital to sustaining the economic production of 99 Mo. The high-yield molybdenum solution extraction (MOEX) process recovers enriched Mo by acidifying spent generator solutions, extracting Mo using tri-n-butyl phosphate (TBP), and stripping Mo into ammonium hydroxide, where it is later converted to solid (NH 4 ) 6 M 07 O 24 (ammonium heptamolybdate or AHM) by crystallization. It is important to produce the AHM product with consistent particle size and morphology before its thermal treatment and reduction to Mo metal in a furnace. AHM particles that are too small (< 50 µm) result in Mo metal powder that is much too fine to properly fabricate into targets with optimum properties.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High Energy Hydroforming Friction Stir Welded 2050 Al-Li Blanks for Aerospace Domes and Cones

Friction stir welded (FSW) aluminum blanks offer larger preform sizes than available from the mill in single width plates. Large blanks made from aerospace-grade aluminum alloys are essential for making large domes and cones for launch vehicles and crew vehicles. Previous research efforts have demonstrated >5m FSW blanks can be formed into large domes or cones using spin forming, but the subsequent solution heat treatment consistently led to abnormal grain growth (AGG). The AGG phenomenon occurs because the FSW blanks must be spin formed in the -O annealed temper to withstand the high strain process without cracking. Subsequently, the solution heat treatment process leads to the onset of AGG, whereby a small number of grains grow much larger than the surrounding matrix. Ultimately, the large grains and bimodal grain-size distribution leads to unacceptable ductility in the short-transverse direction of the part. Alternatively, explosive hydroforming is a nascent process that can be applied to large and thick aerospace-grade aluminum alloy blanks in the -T3 temper and only require a post-forming artificial aging process to a -T8. Avoiding the solution heat treatment (SHT) process mitigates AGG, and also eliminates the need for very rare drop-furnace quench baths that can accommodate a part size larger than 5m in diameter. This presentation summarizes a Lockheed Martin-led effort that demonstrated explosive hydroforming of a 1.9m diameter, 39mm thick 2050 aluminum lithium FSW blank. Details will be provided on the process flow, mechanical properties, and metallographic analyses. This work was performed in partnership with NASA Langley Research Center (LaRC) under a NASA Announcement of Collaboration Opportunities program.

Friction stir welded blank↗

Sketch-To-Solution: An Exploration of Viscous CFD with Automatic Grids

Numerical simulation of the Reynolds-averaged Navier–Stokes (RANS) equations has become a critical tool for the design of aerospace vehicles. However, the issues that affect the grid convergence of three dimensional RANS solutions are not completely understood, as documented in the AIAA Drag Prediction Workshop series. Grid adaption methods have the potential for increasing the automation and discretization error control of RANS solutions to impact the aerospace design and certification process. The realization of the CFD Vision 2030 Study includes automated management of errors and uncertainties of physics-based, predictive modeling that can set the stage for ensuring a vehicle is in compliance with a regulation or specification by using analysis without demonstration in flight test (i.e., certification or qualification by analysis). For example, the Cart3D inviscid analysis package has automated Cartesian cut-cell gridding with output-based error control. Fueled by recent advances in the fields of anisotropic grid adaptation, error estimation, and geometry modeling, a similar work flow is explored for viscous CFD simulations; where a CFD application engineer provides geometry, boundary conditions, and flow parameters, and the sketch-to-solution process yields a CFD simulation through automatic, error-based, grid adaptation.

Kleb, William L.↗

Challenges and Solutions in Operation and Lay-Up of the Modular Caustic- Side Solvent Extraction Unit - 20078

The Modular Caustic-Side Solvent Extraction (CSSX) Unit (MCU) was designed and constructed to provide interim salt waste processing so that the Liquid Waste Disposition Program (LWDP) could continue waste removal and tank closure until start-up of the Salt Waste Processing Facility (SWPF). MCU processes Clarified Salt Solution (CSS), or salt solution (SS) that has undergone actinide removal/filtration, to produce two waste streams: the cesium laden Strip Effluent (SE), which is incorporated into glass at the Defense Waste Processing Facility (DWPF), and the cesium depleted Decontaminated SS (DSS), which is incorporated into grout at the Saltstone Production Facility (SPF). MCU completed start-up in 2008 with an initial operating life of 3 years and design life of 5 years. Prior to reaching the end of the design life, multiple critical components were upgraded and/or replaced to mitigate risks associated with any delays in SWPF start-up. During the remainder of operation (until June 2019), MCU was challenged to maximize processing with minimal additional modifications to repair/improve aging infrastructure, while maintaining low levels of risk to workers and the environment. Notable challenges during the extended operating life of the facility involved both mechanical and operational issues. Two of the most significant issues were the increased frequency of Process Vessel Ventilation (PVV) High Efficiency Particulate Air (HEPA) filter change-outs and the biofouling of the SE coalescer (SEC). The major impacts of both issues were that replacement of these components 1) resulted in high exposure to workers, and 2) required substantial downtime, thus hindering achievement of processing goals. PVV HEPA filter replacements are required based on dose rate and differential pressure (dP) limits. After introducing a higher-curie feed to MCU, the operating time between change outs was reduced by approximately half. SEC replacements are required based on dP limits. After restarting from an extended outage, the operating life of the SEC was significantly reduced by more than half due to biofouling. As a result of extensive troubleshooting and process improvements, the facility was able to recover performance and extend the operating life of the PVV HEPA filters and the SEC media. Through troubleshooting both of these issues, the facility was also able to learn from prior experience and adapt in order to minimize down time and maintain throughput. Although the facility took advantage of short periods of downtime to perform nonintrusive troubleshooting and minor corrective/preventative maintenance activities, longer outages were periodically required for corrective maintenance involving process cell entry. During these outages, remote tools and specialized shield plates were employed to minimize dose to workers. Mock-ups of non-routine maintenance activities were critical to early identification of potential issues and improvements, which shortened outage duration. Consistent with the facility's operational strategy, evolutions needed for MCU layup were identified and sequenced to ensure safe conditions within the facility, meet pre-defined criteria for lay-up configuration, and protect workers, while minimizing the impact to SWPF integration. De-inventory and flushing of process areas was prioritized so that the total residual inventory was reduced as efficiently as possible. This paper discusses lessons learned and best practices from troubleshooting unique issues, performing complex maintenance activities, and implementing a layup strategy that best supports the overall system mission. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Additive manufacturing and processing of architected materials

Architected materials are a unique and emerging class of materials where performance is fundamentally controlled by geometry at multiple length scales, from the nano- to the macroscale, rather than chemical composition alone. As a result, the realization of these remarkable materials is contingent upon the ability to faithfully reproduce the designed architecture. Furthermore, this presents fundamental challenges in fabrication due to the required three-dimensional complexity, multiple length scales, range of material constituents, possibility of multiple materials in a single architecture, and overall manufacturing throughput. Additive manufacturing (AM) processes can provide solutions to some of these challenges and are discussed in this article. Specifically, light-based and extrusion-based processes and associated materials are presented with an emphasis on recent developments, including volumetric additive manufacturing, and on-the-fly mixing of materials in extrusion-based printing systems. While remarkable advancements have been made in AM for architected materials, bringing these materials and processes to industrial realization remains a significant challenge.

36 MATERIALS SCIENCE↗

Plating Processes Utilizing High Intensity Acoustic Beams

A system and a method for selective plating processes are disclosed which use directed beams of high intensity acoustic waves to create non-linear effects that alter and improve the plating process. The directed beams are focused on the surface of an object, which in one embodiment is immersed in a plating solution, and in another embodiment is suspended above a plating solution. The plating processes provide precise control of the thickness of the layers of the plating, while at the same time, in at least some incidents, eliminates the need for masking.

Richard C Oeftering↗

Boron Removal by Adsorption on Cobalt(II) Doped Chitosan Bio-composite

Cobalt(II) doped chitosan bio-composite was prepared, characterized and used to oxoborate separation from aqueous solutions. The adsorption process was carried out in a batch system. The effect of pH, temperature, time and initial boron concentration on the boron adsorption were tested. The maximum boron adsorption was reached at pH range 8.0–8.5 at room temperature and within 60 min. Calculations based on Langmuir and Freundlich models showed the heterogeneous nature of boron adsorption on Co-CTS bio-composite. On the base of research on optimization of pH and results from XRD and FTIR analysis it was found that boron adsorption by Co-CTS occurred through the co-precipitation and adsorption of B on cobalt hydroxide following the Coulomb attraction of B(OH){sub 4}{sup −} species on positively charged sites and molecular attraction of H{sub 3}BO{sub 3} through hydrogen bond with amine or hydroxyl groups of chitosan. The modelling of the thermodynamic data indicated the nonspontaneous and exothermic nature of the adsorption process. The pseudo-second-order model adequately described the boron adsorption on Co-CTS hydrogel. Desorption by means of alkaline solution at pH 12 was carried out successfully. Adsorption–desorption efficiencies in 3 cycles were almost 100%.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

BioRT‐HBV 1.0: A Biogeochemical Reactive Transport Model at the Watershed Scale

Abstract Reactive Transport Models (RTMs) are essential tools for understanding and predicting intertwined ecohydrological and biogeochemical processes on land and in rivers. While traditional RTMs have focused primarily on subsurface processes, recent watershed‐scale RTMs have integrated ecohydrological and biogeochemical interactions between surface and subsurface. These emergent, watershed‐scale RTMs are often spatially explicit and require extensive data, computational power, and computational expertise. There is however a pressing need to create parsimonious models that require minimal data and are accessible to scientists with limited computational background. To that end, we have developed BioRT‐HBV 1.0, a watershed‐scale, hydro‐biogeochemical RTM that builds upon the widely used, bucket‐type HBV model known for its simplicity and minimal data requirements. BioRT‐HBV uses the conceptual structure and hydrology output of HBV to simulate processes including advective solute transport and biogeochemical reactions that depend on reaction thermodynamics and kinetics. These reactions include, for example, chemical weathering, soil respiration, and nutrient transformation. The model uses time series of weather (air temperature, precipitation, and potential evapotranspiration) and initial biogeochemical conditions of subsurface water, soils, and rocks as input, and output times series of reaction rates and solute concentrations in subsurface waters and rivers. This paper presents the model structure and governing equations and demonstrates its utility with examples simulating carbon and nitrogen processes in a headwater catchment. As shown in the examples, BioRT‐HBV can be used to illuminate the dynamics of biogeochemical reactions in the invisible, arduous‐to‐measure subsurface, and their influence on the observed stream or river chemistry and solute export. With its parsimonious structure and easy‐to‐use graphical user interface, BioRT‐HBV can be a useful research tool for users without in‐depth computational training. It can additionally serve as an educational tool that promotes pollination of ideas across disciplines and foster a diverse, equal, and inclusive user community.

Sadayappan, Kayalvizhi↗

Identifying Bounds of Inorganic Content in Solventless Processing of Hybrid Solid Electrolytes

Solid-state lithium batteries require safe, robust electrolytes to enable higher energy densities and improved safety over conventional cells. Hybrid polymer–ceramic electrolytes are a promising solution, combining the processability of polymers with the high ionic conductivity and mechanical strength of inorganic fillers. In this work, we demonstrate a solventless, UV-curing method to produce hybrid solid electrolytes using a poly(ethylene glycol) dimethyl ether (PEGDME)-based photocurable matrix incorporating Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 (LAGP) or Li 7 La 3 Zr 2 O 12 (LLZO) ceramic electrolyte. Inorganic filler loadings up to ∼55 wt.% could be successfully incorporated via this process which was the highest inorganic content at which the slurry remains processable and cured into a uniform film. The resulting UV-cured composite electrolytes remain flexible and exhibit room-temperature ionic conductivities on the order of 10 −4 S·cm −1 , along with notably improved lithium-ion transference numbers compared to conventional polymer electrolytes. Similar performance and processing limits were observed for both LAGP and LLZO, indicating that ceramic filler chemistry does not significantly affect the UV-curing process or the electrolyte's ion transport properties in this regime. Eliminating solvents from fabrication not only simplifies processing and mitigates environmental concerns but also enables higher solid contents that enhance mechanical strength and help suppress lithium dendrite formation. In conclusion, this scalable approach thus paves the way for manufacturing robust composite solid electrolytes for next-generation solid-state batteries (SSBs).

Batteries↗

A Model for Macromolecular Crystallization

Macromolecular crystallization is a complex process. involving a system which typically has 5 or more components (macromolecule, water, buffer + counter ion, and precipitant). Whereas small molecules have only several well defined contacts in the crystal lattice, macromolecules generally have 10's or even 100's of contacts between molecules. These can range from hydrogen bonds (direct or water-mediated), through van der Waals, hydrophobic, salt bridges, and ion-mediated contacts. The latter interactions are stronger and require some specificity in the molecular alignment, while the others are weaker, more prevalent, and more promiscuous, i.e., can often be readily broken and reformed between other sites. Formation of a consistent, ordered, 3D structure may be impossible in the absence of any or presence of too many strong interactions. Further complicating the process is the inherent structural asymmetry of monomeric single chain macromolecules. The process of crystal nucleation and growth involves the ordered assembly of growth units into a defined 3D lattice. We suggest that for many macromolecules, particularly those that are monomeric, this involves a preliminary solution-phase assembly process into a growth unit having some symmetry prior to addition to the lattice, recapitulating the initial stages of the nucleation process. If this model is correct then fluids and crystal growth models assuming a strictly monodisperse nutrient solution need to be revised. Experimental evidence, based upon face growth rate, AFM, and fluorescence energy transfer data, for a postulated model of the nucleation of tetragonal lysozyme crystals and how it transitions into crystal growth will be presented.

Pusey, Marc L.↗

A Model for Tetragonal Lysozyme Crystal Nucleation and Growth

Macromolecular crystallization is a complex process, involving a system that typically has 5 or more components (macromolecule, water, buffer + counter ion, and precipitant). Whereas small molecules have only a few contacts in the crystal lattice, macromolecules generally have 10's or even 100's of contacts between molecules. These can range from hydrogen bonds (direct or water-mediated), through van der Waals, hydrophobic, salt bridges, and ion-mediated contacts. The latter interactions are stronger and require some specificity in the molecular alignment, while the others are weaker, more prevalent, and more promiscuous, i.e., can be readily broken and reformed between other sites. Formation of a consistent, ordered, 3D structure may be difficult or impossible in the absence of any or presence of too many strong interactions. Further complicating the process is the inherent structural asymmetry of monomeric (single chain) macromolecules. The process of crystal nucleation and growth involves the ordered assembly of growth units into a defined 3D lattice. We suggest that for many macromolecules, particularly those that are monomeric, this involves a preliminary solution-phase assembly process into a growth unit having some symmetry prior to addition to the lattice, recapitulating the initial stages of the nucleation process. If this model is correct then fluids and crystal growth models assuming a strictly monodisperse nutrient solution need to be revised. This model has been developed from experimental evidence based upon face growth rate, AFM, and fluorescence energy transfer data for the nucleation and growth of tetragonal lysozyme crystals.

Pusey, Marc L.↗