Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reduced Defects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

Improved VOC in RbF-Treated Cu(In,Ga)Se2 Solar Cells via Passivation of Recombination Centers

Cu(In,Ga)Se 2 (CIGS) solar cells have benefited in recent years from the addition of heavy alkali elements, such as Rb, which increase the solar cell open-circuit voltage ( V OC ). To investigate the source of this improvement, here, we compare samples with and without Rb to perform a quantitative comparison of electronic defects and minority carrier lifetime. Deep-level transient and optical spectroscopy measurements were performed on two sets of rubidium fluoride (RbF)-treated and untreated CIGS, and three distinct traps were identified regardless of RbF treatment. The RbF treatment was found to reduce the concentration of the H2 trap, which was previously found to act as a recombination center and is located preferentially at CIGS grain boundaries. Time-resolved photoluminescence measurements showed an increase in effective lifetime after RbF and nearly all lifetime improvement resulted from reductions in bulk recombination. The observed V OC improvement is well correlated with increased minority carrier lifetime and acceptor concentration, which led to increases and decreases in electron and hole quasi-Fermi levels, respectively.

Cu(In Ga)Se2 (CIGS)↗

CST: A Tool for Optimizing the Efficiency and Effectiveness of Static-Code Analysis Tools

Static Code Analysis (SCA) is a vital component of NASA IV&V’s mission assurance for safety-critical software as it reduces the likelihood of software-induced hazards impacting mission success. Static Code Analysis achieves this by identifying hazards that may not have been otherwise detectable by typical code reviews or other testing. Using SCA tools, however, can be intimidating due to steep learning curves, especially considering tool performance and defect coverage varies greatly. Because of this variation amongst SCA tools, understanding which tools support certain defects and which do not, as well as understanding how to run an analysis based on steps that are unique to each tool, can be difficult to both new and experienced analysts alike. To mitigate this, the SCAWG or the IV&V Static Code Analysis Working Group, created the SCA Checker Taxonomy and Starting Point Profiles. The Checker Selection Tool (CST) incorporates these two SCAWG products into an interactive tool which allows the user to: select organized categories of defects they would like the SCA tools to discover, select default checkers depending on their mission type (e.g. flight), and configure multiple SCA tools at once. C/C++, Java, and Python defect checkers from four common SCA tools were utilized in this iteration of the CST. This iteration also includes the addition of training, SCA tool specific help, and taxonomy guide links, into its design to help users new to Static Code Analysis learn how to perform SCA more efficiently. The CST has been subject to beta testing by experienced static code analysts from the SCAWG to ensure a usable and accurate final product. The implications of the CST in the mission assurance of NASA safety-critical software are profound, as the CST can help identify and reduce false positives and false negatives, fundamentally improving overall SCA efficiency and accuracy.

static code analysis↗

How non-ohmic contact-layer diodes in perovskite pinholes affect abrupt low-voltage reverse-bias breakdown and destruction of solar cells

Perovskite solar cells (PSCs) rapidly degrade under reverse bias, a condition that may occur during partial shading. Here, in this study, we use electrical measurements, electron microscopy, and optical and thermal imaging to investigate abrupt breakdown and hotspotting under low reverse potentials (<|-2| V). We show that microscopic pinholes in the perovskite layer cause rapid, destructive breakdown under reverse bias despite minimally reducing power conversion efficiencies. Measurements on miniature (200-micrometer diameter) PSCs and perovskite-free transport-layer diodes indicate that abrupt, low-voltage breakdown occurs in nanoscale to micrometer-scale defects and that metal migration and filamentation are unlikely causes. Reverse-bias stability substantially improves when pinholes in the perovskite and transport layers are eliminated. Atomic layer deposition of tin oxide prevents abrupt breakdown by ensuring physical separation between electrodes-not by blocking metal ion migration. Perovskite researchers should adopt cleaner, more uniform deposition techniques to enable robust PSCs for further research and commercial applications.

14 SOLAR ENERGY↗

Defective TiO 2 with high photoconductive gain for efficient and stable planar heterojunction perovskite solar cells

Formation of planar heterojunction perovskite solar cells exhibiting both high efficiency and stability under continuous operation remains a challenge. Here, we show this can be achieved by using a defective TiO 2 thin film as the electron transport layer. TiO 2 layers with native defects are deposited by electron beam evaporation in an oxygen-deficient environment. Deep-level hole traps are introduced in the TiO 2 layers and contribute to a high photoconductive gain and reduced photocatalytic activity. The high photoconductivity of the TiO 2 electron transport layer leads to improved efficiency for the fabricated planar devices. A maximum power conversion efficiency of 19.0% and an average PCE of 17.5% are achieved. In addition, the reduced photocatalytic activity of the TiO 2 layer leads to enhanced long-Term stability for the planar devices. Under continuous operation near the maximum power point, an efficiency of over 15.4% is demonstrated for 100 h.

14 SOLAR ENERGY↗

How additives for tin halide perovskites influence the Sn 4+ concentration

Tin halide perovskite (Sn-HPs) photovoltaics could potentially equal or exceed the performance of their more toxic Pb-based analogues if defect state densities, particularly originating from the presence of Sn 4+ , can be significantly decreased. Numerous additives are incorporated into Sn-HPs to minimize the amount of Sn 4+ , including SnF 2 , reducing agents such as hydrazine derivatives, and various antioxidants. However, despite the frequent use of additives to reduce Sn 4+ content, there is limited understanding of how they function and consequently limited guidance for the development of new additives. Herein, we use cyclic voltammetry to probe the redox behavior of SnI 2 , SnI 4 , Sn-HP precursor solutions, and 18 different additives. Through 119 Sn NMR measurements we show that hydrochloride containing additives undergo halide exchange with SnI 4 to form SnI x Cl y , which results in decreased Sn 4+ concentrations and less p-type character in the Sn-HP films. We find that the most effective additive at lowering the Sn 4+ content in FASnI 3 is not capable of reducing SnI 4 or forming SnI x Cl y , but rather it acts as a sacrificial and coordinating antioxidant. In general, when selecting additives for Sn-HPs it is important to account for the redox potential, coordination with Sn species, ability to react with oxygen, and the potential for halide exchange.

36 MATERIALS SCIENCE↗

The impact of oxygen incorporation during intrinsic ZnO sputtering on the performance of Cu(In,Ga)Se{sub 2} thin film solar cells

We investigated the impact of incorporating 2% oxygen during intrinsic ZnO sputtering on the efficiency of Cu(In,Ga)Se{sub 2} solar cells. The added oxygen not only reduced the optical absorption loss of the Al-doped ZnO overlaying layer but also improved the electronic properties of the underlying CdS/Cu(In,Ga)Se{sub 2} by increasing carrier density, lowering defect level, and increasing diffusion length, eventually enhancing J{sub SC}, V{sub OC}, and fill factor. It was found that the Na doping concentration was significantly increased around the CdS/Cu(In,Ga)Se{sub 2} junction due to the plasma-activated oxygen. The improved electronic properties are better explained by the increased Na concentration than simply the oxygen-related defect passivation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Engineering of niobium surfaces through accelerated neutral atom beam technology for quantum applications

A major roadblock to scalable quantum computing is phase decoherence and energy relaxation caused by qubits interacting with defect-related two-level systems (TLSs). Native oxides present on the surfaces of superconducting metals used in quantum devices are acknowledged to be a source of TLS that decrease qubit coherence times. Reducing microwave loss by “surface engineering” (i.e., replacing the uncontrolled native oxide of superconducting metals with a thin, stable surface with predictable characteristics) can be a key enabler for pushing performance forward with devices of higher intrinsic quality factor. In this work, we present a novel approach to replace the native oxide of niobium (typically formed in an uncontrolled fashion when its pristine surface is exposed to air) with an engineered oxide, using a room-temperature process that leverages accelerated neutral atom beam (ANAB) technology at 300 mm wafer scale. This ANAB is composed of a mixture of argon and oxygen, with tunable energy per atom, which is rastered across the wafer surface. The ANAB-engineered Nb-oxide thickness was found to vary from 2 to 6 nm depending on ANAB process parameters. The modeling of variable-energy x-ray photoelectron spectroscopy data confirms the thickness and compositional control of Nb surface oxide by the ANAB process. Furthermore, these results correlate well with those from transmission electron microscopy and x-ray reflectometry. Since ANAB is broadly applicable to material surfaces, the present study indicates its promise for modification of the surfaces of superconducting quantum circuits to achieve longer coherence times.

36 MATERIALS SCIENCE↗

Canine CNGA3 Gene Mutations Provide Novel Insights into Human Achromatopsia-Associated Channelopathies and Treatment

Cyclic nucleotide-gated (CNG) ion channels are key mediators underlying signal transduction in retinal and olfactory receptors. Genetic defects in CNGA3 and CNGB3, encoding two structurally related subunits of cone CNG channels, lead to achromatopsia (ACHM). ACHM is a congenital, autosomal recessive retinal disorder that manifests by cone photoreceptor dysfunction, severely reduced visual acuity, impaired or complete color blindness and photophobia. Here, we report the first canine models for CNGA3-associated channelopathy caused by R424W or V644del mutations in the canine CNGA3 ortholog that accurately mimic the clinical and molecular features of human CNGA3-associated ACHM. These two spontaneous mutations exposed CNGA3 residues essential for the preservation of channel function and biogenesis. The CNGA3-R424W results in complete loss of cone function in vivo and channel activity confirmed by in vitro electrophysiology. Structural modeling and molecular dynamics (MD) simulations revealed R424-E306 salt bridge formation and its disruption with the R424W mutant. Reversal of charges in a CNGA3-R424E-E306R double mutant channel rescued cGMP-activated currents uncovering new insights into channel gating. The CNGA3-V644del affects the C-terminal leucine zipper (CLZ) domain destabilizing intersubunit interactions of the coiled-coil complex in the MD simulations; the in vitro experiments showed incompetent trimeric CNGA3 subunit assembly consistent with abnormal biogenesis of in vivo channels. These newly characterized large animal models not only provide a valuable system for studying cone-specific CNG channel function in health and disease, but also represent prime candidates for proof-of-concept studies of CNGA3 gene replacement therapy for ACHM patients.

59 BASIC BIOLOGICAL SCIENCES↗

Enabling Next Generation Reaction Injection Molding (RIM) for Lightweight Structures

Replacing metal components in trucks, trailers, and buses with lightweight polymer composites is challenging due to high temperatures and complex manufacturing. The Reaction Injection Molding (RIM) process using Dicyclopentadiene (DCPD) resin offers a solution by producing robust parts with excellent stiffness, impact strength, and resistance properties. Simulations are essential for optimizing this process, predicting defects, and improving quality. However, most commercial software is tailored for thermoplastics, requiring thermoset users to generate their own datasets. In this project, a material data card for DCPD was developed to perform RIM simulations. Design of Experiments (DOE) was used to identify key factors affecting filling, curing, and warpage, aiming to minimize cycle time and defects. The simulations explored varying injection gate parameters (size, location, number) and process conditions (mold/resin temperature, injection/curing pressure). Results showed that gate design significantly impacts filling behavior and defects. A single central gate provided balanced flow with fewer defects, while two corner gates led to more defects. Additionally, lower injection pressure increased filling time, while higher mold temperature accelerated curing but led to more warpage. This optimization framework aims to enhance DCPD part performance and promote sustainable manufacturing by reducing waste and energy consumption. This research has been performed in collaborations with McClarin Composites. The research outcome has been submitted to the Journal of Manufacturing Processes.

36 MATERIALS SCIENCE↗

The effect of leveling coatings on the atomic oxygen durability of solar concentrator surfaces

Space power systems for Space Station Freedom will be exposed to the harsh environment of low earth orbit (LEO). Neutral atomic oxygen is the major constituent in LEO and has the potential of severely reducing the efficiency of solar dynamic power systems through degradation of the concentrator surfaces. Several transparent dielectric thin films have been found to provide atomic oxygen protection, but atomic oxygen undercutting at inherent defect sites is still a threat to solar dynamic power system survivability. Leveling coatings smooth microscopically rough surfaces, thus eliminating potential defect sites prone to oxidation attack on concentrator surfaces. The ability of leveling coatings to improve the atomic oxygen durability of concentrator surfaces was investigated. The application of a EPO-TEK 377 epoxy leveling coating on a graphite epoxy substrate resulted in an increase in solar specular reflectance, a decrease in the atomic oxygen defect density by an order of magnitude and a corresponding order of magnitude decrease in the percent loss of specular reflectance during atomic oxygen plasma ashing.

Degroh, Kim K.↗

Damage Detection in Rotorcraft Composite Structures Using Thermography and Laser-Based Ultrasound

New rotorcraft structural composite designs incorporate lower structural weight, reduced manufacturing complexity, and improved threat protection. These new structural concepts require nondestructive evaluation inspection technologies that can potentially be field-portable and able to inspect complex geometries for damage or structural defects. Two candidate technologies were considered: Thermography and Laser-Based Ultrasound (Laser UT). Thermography and Laser UT have the advantage of being non-contact inspection methods, with Thermography being a full-field imaging method and Laser UT a point scanning technique. These techniques were used to inspect composite samples that contained both embedded flaws and impact damage of various size and shape. Results showed that the inspection techniques were able to detect both embedded and impact damage with varying degrees of success.

Anastasi, Robert F.↗

Nanomechanics and nanometallurgy of boundaries.

One of the tenets of nanotechnology is that the electrical/optical/chemical/biological properties of a material may be changed profoundly when the material is reduced to sufficiently small dimensions - and we can exploit these new properties to achieve novel or greatly improved material's performance. However, there may be mechanical or thermodynamic driving forces that hinder the synthesis of the structure, impair the stability of the structure, or reduce the intended performance of the structure. Examples of these phenomena include de-wetting of films due to high surface tension, thermally-driven instability of nano-grain structure, and defect-related internal dissipation. If we have fundamental knowledge of the mechanical processes at small length scales, we can exploit these new properties to achieve robust nanodevices. To state it simply, the goal of this program is the fundamental understanding of the mechanical properties of materials at small length scales. The research embodied by this program lies at the heart of modern materials science with a guiding focus on structure-property relationships. We have divided this program into three Tasks, which are summarized: (1) Mechanics of Nanostructured Materials (PI Blythe Clark). This task aims to develop a fundamental understanding of the mechanical properties and thermal stability of nanostructured metals, and of the relationship between nano/microstructure and bulk mechanical behavior through a combination of special materials synthesis methods, nanoindentation coupled with finite-element modeling, detailed electron microscopic characterization, and in-situ transmission electron microscopy experiments. (2) Theory of Microstructures and Ensemble Controlled Deformation (PI Elizabeth A. Holm). The goal of this Task is to combine experiment, modeling, and simulation to construct, analyze, and utilize three-dimensional (3D) polycrystalline nanostructures. These full 3D models are critical for elucidating the complete structural geometry, topology, and arrangements that control experimentally-observed phenomena, such as abnormal grain growth, grain rotation, and internal dissipation measured in nanocrystalline metal. (3) Mechanics and Dynamics of Nanostructured and Nanoscale Materials (PI John P. Sullivan). The objective of this Task is to develop atomic-scale understanding of dynamic processes including internal dissipation in nanoscale and nanostructured metals, and phonon transport and boundary scattering in nanoscale structures via internal friction measurements.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Mn-doped oxide nuclear fuel

A nuclear fuel includes uranium(IV) oxide (UO2) and manganese (Mn) as a dopant. The Mn dopant may be present in the fuel in an amount up to the solubility limit for Mn under a given set of conditions, for example, about 0.01 wt % to about 1 wt %. The nuclear fuel is substantially free of aluminum (Al). The nuclear fuel exhibits enhanced grain size development during sintering temperatures as low at 1400 K due to an increase in uranium sub-lattice vacancies induced by dissolution of the Mn dopant at interstitial defect sites. The Mn-doped nuclear fuel exhibits improved grain sizes at lower temperatures compared to Cr-, Al-, and undoped UO2, and therefore desirably exhibits lower fission gas release and higher plasticity, reducing the chances of fuel rod failure.

Cooper, Michael William Donald↗

Impact of implanted phosphorus on the diffusivity of boron and its applicability to silicon solar cells

Boron diffusivity reduction in extrinsically doped silicon was investigated in the context of a process combination consisting of BBr{sub 3} furnace diffusion and preceding Phosphorus ion implantation. The implantation of Phosphorus leads to a substantial blocking of Boron during the subsequent Boron diffusion. First, the influences of ion implantation induced point defects as well as the initial P doping on B diffusivity were studied independently. Here, it was found that not the defects created during ion implantation but the P doping itself results in the observed B diffusion retardation. The influence of the initial P concentration was investigated in more detail by varying the P implantation dose. A secondary ion mass spectrometry (SIMS) analysis of the BSG layer after the B diffusion revealed that the B diffusion retardation is not due to potential P content in the BSG layer but rather caused by the n-type doping of the crystalline silicon itself. Based on the observations the B diffusion retardation was classified into three groups: (i) no reduction of B diffusivity, (ii) reduced B diffusivity, and (iii) blocking of the B diffusion. The retardation of B diffusion can well be explained by the phosphorus doping level resulting in a Fermi level shift and pairing of B and P ions, both reducing the B diffusivity. Besides these main influences, there are probably additional transient phenomena responsible for the blocking of boron. Those might be an interstitial transport mechanism caused by P diffusion that reduces interstitial concentration at the surface or the silicon/BSG interface shift due to oxidation during the BBr{sub 3} diffusion process. Lifetime measurements revealed that the residual (non-blocked) B leads to an increased dark saturation current density in the P doped region. Nevertheless, electrical quality is on a high level and was further increased by reducing the B dose as well as by removing the first few nanometers of the silicon surface after the BBr{sub 3} diffusion.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Local charge transport properties of hydrazine reduced monolayer graphene oxide sheets prepared under pressure condition

Charge transport properties of chemically reduced graphene oxide (RGO) sheets prepared by treatment with hydrazine were examined using conductive atomic force microscopy. The current-voltage (I-V) characteristics of monolayer RGO sheets prepared under atmospheric pressure followed an exponentially increase due to 2D variable-range hopping conduction through small graphene domains in an RGO sheet containing defect regions of residual sp{sup 3} carbon clusters bonded to oxygen groups, whereas RGO sheets prepared in a closed container under moderate pressure showed linear I-V characteristics with a conductivity of 267.2−537.5 S/m. It was found that the chemical reduction under pressure results in larger graphene domains (sp{sup 2} networks) in the RGO sheets when compared to that prepared under atmospheric pressure, indicating that the present reduction of GO sheets under the pressure is one of the effective methods to make well-reduced GO sheets.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Spatially Resolved Mapping of Electrical Conductivity around Individual Domain (Grain) Boundaries in Graphene

Graphene films can now be produced on the scale of up to meters. However, all large-scale graphene films contain topological defects that can significantly affect the characteristic transport behaviors of graphene. Here, we spatially map the structures and electronic transport near specific domain and grain boundaries in graphene, and evaluate effects of different types of defect on the electronic conductivity in epitaxial graphene grown on SiC and CVD graphene on Cu subsequently transferred to a SiO2 substrate. We use a combined approach with a multi-probe scanning tunneling potentiometry to investigate both structures and transport at individual grain boundaries and domain boundaries that are defined by coalesced grains, surface steps, and changes in layer thickness. It is found that the substrate step on SiC presents a significant potential barrier for electron transport of epitaxial graphene due to the reduced charge transport from the substrate at the step edges, monolayer-bilayer boundaries exhibit a high resistivity that can change depending on directions of the current across the boundary, and the resistivity of grain boundaries changes with the transition width of the disordered region between two adjacent grains in graphene. The detailed understanding of graphene defects will provide the feedback for controlled engineering of defects in large-scale graphene films.

Li, An-Ping↗

Interpolative Separable Density Fitting Decomposition for Accelerating Hybrid Density Functional Calculations with Applications to Defects in Silicon

We present a new efficient way to perform hybrid density functional theory (DFT)-based electronic structure calculations. The new method uses an interpolative separable density fitting (ISDF) procedure to construct a set of numerical auxiliary basis vectors and a compact approximation of the matrix consisting of products of occupied orbitals represented in a large basis set such as the planewave basis. Such an approximation allows us to reduce the number of Poisson solves from O ($N$ $^{2}_{ϵ}$) to O ( N ϵ ) when we apply the exchange operator to occupied orbitals in an iterative method for solving the Kohn–Sham equations, where Ne is the number of electrons in the system to be studied. We show that the ISDF procedure can be carried out in O ($N$ $^{3}_{ϵ}$) operations, with a much smaller preconstant compared to methods used in existing approaches. When combined with the recently developed adaptively compressed exchange (ACE) operator formalism, which reduces the number of times the exchange operator needs to be updated, the resulting ACE-ISDF method significantly reduces the computational cost associated with the exchange operator by nearly 2 orders of magnitude compared to existing approaches for a large silicon system with 1000 atoms. We demonstrate that the ACE-ISDF method can produce accurate energies and forces for insulating and metallic systems and that it is possible to obtain converged hybrid functional calculation results for a 1000-atom bulk silicon within 10 min on 2000 computational cores. We also show that ACE-ISDF can scale to 8192 computational cores for a 4096-atom bulk silicon system. We use the ACE-ISDF method to geometrically optimize a 1000-atom silicon system with a vacancy defect using the HSE06 functional and computes its electronic structure. Here, we find that that the computed energy gap from the HSE06 functional is much closer to the experimental value compared to that produced by semilocal functionals in the DFT calculations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

As‐Doped Polycrystalline CdSeTe: Localized Defects, Carrier Mobility and Lifetimes, and Impact on High‐Efficiency Solar Cells

Abstract The efficiency potential for single‐junction photovoltaics (PV) is described by the detailed balance model, which requires the elimination of nonradiative recombination and perfect minority carrier collection. Improvements in GaAs, Si, and perovskite PV follow this model. It might be more complex for CdTe, a leading thin‐film PV technology. While lifetime, passivation, and doping goals for 25% efficient CdTe solar cells are largely reached, voltage is ≈20% below the detailed balance limit. Why is that? In Se‐alloyed CdSe x Te 1‐x (Se is required for >20% efficiency) additional losses can occur due to electrostatic and bandgap fluctuations and due to electronic trap states. To understand mechanisms limiting CdSeTe solar cell performance and to suggest improvements, carrier dynamics, and transport in CdSe x Te 1‐x with variation in Se composition and as doping is analyzed. It is shown that trapping, likely due to anion‐site defects and their complexes, is correlated with low charge carrier mobility of 0.1–0.6 cm 2 (Vs) −1 . Even with 1000 ns charge carrier lifetimes, carrier diffusion length is less than the absorber thickness, reducing efficiency to ≈23%. Device simulations are used to analyze the performance of CdSe x Te 1‐x solar cells; thermodynamic models are not sufficient for absorbers with electronic disorder and trapping.

14 SOLAR ENERGY↗