SEARCH · Search NASA
Results for “Solar Modulation”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Numerical Analysis of Water Harvesting from Saturated Vapor with the Electrospray Water Droplet Injection in The Solar-Driven Desalination Applications
Solar-driven seawater desalination systems provide freshwater through environmentally friendly and carbon-neutral processes. Air humidification and dehumidification desalination (HDD) systems extract water directly from moist air. This paper focuses on a new solar-driven seawater desalination system that shares some common traits with HDD systems but in which the air is eliminated from the process. Seawater is vaporized by solar thermal radiation in high-performance solar panels. Water vapor flows to a new electro-condensation chamber and passes through a series of electrosprays, which inject small nuclei of freshwater droplets into the vapor clouds. Here, due to dielectrophoresis and electrohydrodynamic flows, the vapor molecules are captured by the charged droplets, and vapor is condensed at the droplet surface. The water vapor condensation was modeled by using the multiphase flow numerical model. The CFD model, which was also experimentally validated, used SprayFoam solver modules available in the Open FOAM® CFD open-source software. In preliminary results, 802 grams/(hr-m2) (grams per hour per unit area) of water was harvested directly from moist air at 24C and 90% relative humidity. The simulation results indicated that freshwater productivity could increase up to 4,000 grams/(hr-m2) for fully saturated air conditions. This represents about 5 times the water productivity rate of current conventional HDD systems today. In addition, energy consumption could be reduced by 80 percent compared to conventional HDD systems.
Assessing the Impacts of Extreme Weather Events on Photovoltaic Installations Using Remote Sensing Imagery
In this study, we analyze poststorm satellite imagery to assess solar photovoltaic (PV) damage for over 11,300 systems following a catastrophic hailstorm in Austin, TX, in September 2023, which produced softball‐sized hail and for over 1500 systems across Puerto Rico and the US Virgin Islands after Hurricanes Irma and Maria in September 2017. Findings show that approximately 5.5% of identified PV sites were damaged in the hailstorm and approximately 17% of PV installations were damaged after the hurricanes. A weak correlation between hurricane wind gust speed and percent site damage was determined, with installation practices playing a heavy role in site resilience. Additionally, we show that newer module vintages are more susceptible to hail damage than older modules, possibly due to a convergence of larger size modules, decreased frame dimensions, and decreased front glass thickness but more research is needed. For hail sizes of 60 mm or greater, consistent hail damage is sustained by PV installations, regardless of system configuration.
Surface and Interface Properties in Thin‐Film Solar Cells: Using Soft X‐rays and Electrons to Unravel the Electronic and Chemical Structure
Abstract Thin‐film solar cells have great potential to overtake the currently dominant silicon‐based solar cell technologies in a strongly growing market. Such thin‐film devices consist of a multilayer structure, for which charge‐carrier transport across interfaces plays a crucial role in minimizing the associated recombination losses and achieving high solar conversion efficiencies. Further development can strongly profit from a high‐level characterization that gives a local, electronic, and chemical picture of the interface properties, which allows for an insight‐driven optimization. Herein, the authors' recent progress of applying a “toolbox” of high‐level laboratory‐ and synchrotron‐based electron and soft X‐ray spectroscopies to characterize the chemical and electronic properties of such applied interfaces is provided. With this toolbox in hand, the activities are paired with those of experts in thin‐film solar cell preparation at the cutting edge of current developments to obtain a deeper understanding of the recent improvements in the field, e.g., by studying the influence of so‐called “post‐deposition treatments”, as well as characterizing the properties of interfaces with alternative buffer layer materials that give superior efficiencies on large, module‐sized areas.
Large-Area Material and Junction Damage in c–Si Solar Cells by Potential-Induced Degradation
This paper reports a new potential-induced degradation (PID) mechanism for crystalline silicon (c-Si), where Na diffuses everywhere and causes large-area material and junction degradation with point defects. Multiple characterization techniques are combined - Kelvin probe force microscopy, electron-beam induced current, dark lock-in thermography, transmission electron microscopy, time-of-flight secondary-ion mass spectrometry, and microwave photoconductance decay - as well as density functional theory (DFT) calculations. These characterization techniques and theoretical calculations are complementary in various aspects of a material's chemical, structural, electrical, and optoelectrical nature, as well as in atomic, nanometer, micrometer, millimeter, and cell and module scales. All results point consistently to a new discovery: substantial large-area deterioration of materials and junctions play a major role in c-Si PID (in addition to the previously reported local shunting defect caused by Na diffusion to planar defects). Furthermore, this new finding reveals a key PID component and leads to a new strategy for tailoring c-Si photovoltaics to ultimately resolve the PID issue.
Watching Polarons Dance: Coherent Carrier–Phonon Coupling in Hematite Revealed by Transient Absorption Spectroscopy
Hematite remains a prominent photoanode candidate for the oxygen evolution reaction in solar water splitting, despite efficiency limitations from rapid trapping of photoexcited electrons and holes. While the formation of polarons, quasiparticles formed by electron–hole interactions with lattice vibrations, is a proposed trapping mechanism, direct evidence of such states has been elusive. Here, we use potential-dependent transient absorption spectroscopy to identify the coherent phonon mode and strong exciton–phonon coupling responsible for exciton–polaron formation after band gap excitation in α-hematite and identify the three underlying d–d transitions that are strongly modulated by this phonon. The equilibrium geometry of exciton–polarons in α-hematite is displaced from the ground state geometry along the vibrational coordinate of an A 1g symmetric Fe–O stretching motion at 225 ± 7 cm –1 , resulting in vibrational coherence with a lifetime of 1.9 ± 0.1 ps. Our comparative ex situ and in situ experiments reveal that the energy and dephasing time of the A 1g mode are remarkably resilient to applied potential and the addition of an Al 2 O 3 overlayer; however, the dephasing time is sensitive to substrate identity. Furthermore, this potential-dependent transient absorption approach establishes a powerful platform for directly probing polaron dynamics in photoelectrochemical systems, opening new pathways to rationally design modified hematite and other transition metal oxide electrodes with enhanced charge transport properties for more efficient solar water splitting.
Modeling of the effectiveness of novel edge seal designs for fast, low‐Cap‐Ex manufacturing
Abstract In the manufacturing of photovoltaic (PV) modules, the lamination process can take up to 20 min to complete. In this work, new lamination processes are being developed, and have been prototyped, which hope to be able to cut this time down to as little as 30 s. This could provide significant savings in the cost of lamination equipment, floor space, and energy. PV modules are expected to have a lifespan exceeding 20 to 30 years. For moisture‐sensitive PV technologies, the edge seal between the two layers of glass can be the weakest point of its reliability. There is an inherent challenge when evaluating edge seal materials due to their low permeation rates. As part of Colorado State University's Photovoltaic Research and Development 2, work at the National Renewable Energy Laboratory has developed models to evaluate edge seal configurations in glass‐glass PV modules. Here, this new manufacturing process is evaluated for long‐term moisture durability. Different edge seal design options within glass–glass PV modules are explored. Most of these designs are targeting a superstrate on glass configuration, e.g CdTe, but some designs could be used on conventional crystalline Si cells. Using COMSOL finite element simulation software, we investigated the edge seal and interlayer design configurations containing silicone perimeter edge adhesive, desiccated polyisobutylene‐based edge seal, air, and polyolefin while integrating climate conditions equivalent to a hot and humid environment such as Miami, Florida. We found optimized configurations that will allow the module to prevent moisture ingress over 50 years minimizing the amount of time and material used while utilizing polymers that are easily dispensed.
Floating Photovoltaic System Cost Benchmark: Q1 2021 Installations on Artificial Water Bodies
In this report, we conduct a bottom-up analysis of the installed costs for FPV systems deployed on artificial water bodies under average site conditions (wind load of about 40 m/s, snow load of 20 psf, water depth of 50 m, water level variation of 10 m, and swell height of 1 m). We estimate an installed system cost premium of $\$0.26$/WDC (25%) for 10-MWDC fixed-tilt FPV systems, compared with ground-mounted, fixed-tilt PV installed over bare ground. Higher structural costs related to the floats and anchoring system are the largest contributors to this premium. Currently, site investigation costs are also higher for FPV because of the additional effort needed to plan and design these more complex installations. Our preliminary sensitivity analysis shows that the installed cost of FPV systems is most sensitive to float costs, wind and snow loading, and module efficiency. FPV deployment is in an early stage, and additional experience, best practice development, and new configurations and technologies could help reduce the costs of FPV systems over time.
PACT Module Preconditioning Protocol (V.0.1)
The purpose of this protocol is to bring metal halide perovskite (MHP) modules to a repeatable and relevant state prior to making a performance measurement. Performance measurements are made before and after a stressor has been applied to the module to quantify the degree of loss resulting from the stressor. This procedure is intended to be carried out both before and after the accelerated test.
Durability Research Is Pivotal for Perovskite Photovoltaics
Metal halide perovskite solar cells have shown promising power conversion efficiencies, but commercialization requires that decent durability is also demonstrated. Under normal operation, solar cells are subject to a complex combination of stressors, such as visible light, ultraviolet light, heat, humidity, mechanical stress and electric potential, which complicates the understanding of failure mechanisms. Existing stress tests do not act as a time machine. In new materials systems such as perovskite photovoltaics, the tests have no known relationship to field service. In this Perspective we recommend following a durability learning cycle that interleaves photovoltaic module engineering with field testing; accelerated testing; and preconditioning and performance engineering. We advocate for field testing to demonstrate real-world performance and identify field-relevant failure modes, and urge the community to develop accelerated and qualification tests that account for device metastability, variations in material composition and different/various processing methods. In conclusion, these practices are more difficult, but more important, than the simple pursuit of higher initial efficiencies.
Ultrafast vibrational control of organohalide perovskite optoelectronic devices using vibrationally promoted electronic resonance
Vibrational control (VC) of photochemistry through the optical stimulation of structural dynamics is a nascent concept only recently demonstrated for model molecules in solution. Extending VC to state-of-the-art materials may lead to new applications and improved performance for optoelectronic devices. Metal halide perovskites are promising targets for VC due to their mechanical softness and the rich array of vibrational motions of both their inorganic and organic sublattices. Here, we demonstrate the ultrafast VC of FAPbBr 3 perovskite solar cells via intramolecular vibrations of the formamidinium cation using spectroscopic techniques based on vibrationally promoted electronic resonance. The observed short (~300 fs) time window of VC highlights the fast dynamics of coupling between the cation and inorganic sublattice. First-principles modelling reveals that this coupling is mediated by hydrogen bonds that modulate both lead halide lattice and electronic states. Cation dynamics modulating this coupling may suppress non-radiative recombination in perovskites, leading to photovoltaics with reduced voltage losses.
Chalcogen effect on the photovoltaic performance of nonfused-ring small molecular electron acceptors for efficient organic solar cells
Fused-ring electron acceptors (FREAs) are the current working horse for the top performing organic solar cells (OSCs). Nevertheless, these FREAs surfer from high synthetic complexity, production costs and poor scalability, hindering their industrialization. Developing nonfused-ring electron acceptors (NFREAs) is a more feasible alternative solution towards future photovoltaic applications. Here, in this work, a series of NFREAs have been designed and synthesized by introducing chalcogen atoms on the side chains for OSCs. The introduced chalcogen atoms (O, S, and Se) not only modulated the energy levels but also finely tuned the intermolecular interactions. Especially, the formed S···S and Se···Se intermolecular interactions in TTS-4F and TTSe-4F resulted in higher molecular crystallinity than TTO-4F. Unexpectedly, the strong Se···Se interactions also led the aggregation of TTSe-4F and formation of large domains in the PM6:TTSe-4F blend. The moderate S···S interactions in TTS-4F enabled an optimal phase separation with more ideal nano fibrils distributed in the PM6:TTS-4F blend, facilitating the charge separation and transport. As a result, TTS-4F based devices achieved a champion power conversion efficiency (PCE) of 14.74%, higher than the TTO-4F (8.76%) and TTSe-4F (11.56%) based devices.
Blading Phase–Pure Formamidinium–Alloyed Perovskites for High–Efficiency Solar Cells with Low Photovoltage Deficit and Improved Stability
Currently, blade-coated perovskite solar cells (PSCs) with high power conversion efficiencies (PCEs), i.e. greater than 20%, normally employ methylammonium lead tri-iodide with a sub-optimal bandgap. Alloyed perovskites with formamidinium (FA) cation have narrower bandgap and thus enhance device photocurrent. However, FA-alloyed perovskites show low phase stability and high moisture sensitivity. Here, we report that incorporating 0.83 molar percent organic halide salts (OHs) into the perovskite inks enables phase-pure, highly crystalline FA-alloyed perovskites with extraordinary optoelectronic properties. Here, the OH molecules modulate the crystal growth, enhance the phase stability, passivate ionic defects at the surface and/or grain boundaries, and enhance the moisture stability of the perovskite film. We demonstrate a high efficiency of 22.0% under 1 sun illumination for blade-coated PSCs with an open-circuit voltage of 1.18 V, corresponding to a very small voltage deficit of 0.33 V, and significantly improved operational stability with 96% of the initial efficiency retained under one sun illumination for 500 hours.
Corrosion of novel reactive silver ink and commercial silver-based metallizations in diluted acetic acid
Silver-based metallizations in photovoltaic modules are susceptible to corrosion by acetic acid generated in ethylene vinyl acetate encapsulated modules, resulting in power losses over time. Here, three silver-based metallizations are exposed to diluted acetic acid, in concentrations representative of that found in field-exposed modules. Compositional, morphological, and structural changes of the metallizations are studied over 3000 h of exposure to diluted acetic acid using Raman spectroscopy mapping, X-ray diffraction, and scanning electron microscopy. The three metallizations studied are: 1) a commercial high-temperature fire-through Ag paste, commonly used for Si diffused junction solar cells; 2) a commercial low-temperature paste normally used for silicon heterojunction cells; and 3) a novel low-temperature reactive silver ink shown to be suitable for photovoltaic applications. We find distinct corrosion rates for the high-temperature silver paste and reactive silver ink in the presence of diluted acetic acid. However, the low-temperature silver paste appears to be more corrosion resistant, likely due to a polymer layer that protects the silver particles.
Combined Effects of Hemicolligation and Ion Pairing on Reduction Potentials of Biphenyl Radical Cations
Here, formal reduction potentials of highly oxidizing and short-lived radical cations of substituted biphenyls generated by pulse radiolysis in 1,2-dichloroethane (DCE) were measured using a redox equilibrium ladder method. The effect of halide ion–radical interactions on reduction potentials of biphenyls was examined by utilizing the ability of DCE to release Cl – in the vicinity of the radical cation. The Hammett correlation of measured potentials across a range of over 700 mV shows saturation at high Hammett sigma values. This effect has been explained by both ion-pairing and hemicolligation interactions between biphenyl radical cations and Cl – and appears to modulate reduction potentials by as much as 400 mV. This finding offers a convenient way to manipulate the energetics of electron transfer involving organic redox species.
Bottom-Up Cost Analysis of a High Concentration PV Module
We present a bottom-up model of III-V multi-junction cells, as well as a high concentration PV (HCPV) module. We calculate $0.59/W(DC) manufacturing costs for our model HCPV module design with today's capabilities, and find that reducing cell costs and increasing module efficiency offer the most promising paths for future cost reductions. Cell costs could be significantly reduced via substrate reuse and improved manufacturing yields.
Real-time Simulation Framework for Hardware-in-the-Loop Testing of Multi-port Autonomous Reconfigurable Solar Power Plant (MARS)
Multiport autonomous reconfigurable solar power plant (MARS) has been proposed for integrated development of photovoltaic (PV) and energy storage system (ESS) that can connect to high-voltage direct current (HVdc) and alternating current (ac) transmission grid. To de-risk the development of this complex integrated system that consists of hundreds to thousands of power electronics modules, a controller hardware-in-the-loop (cHIL) test setup will be extremely beneficial. The cHIL testing can be used for evaluation of modules as well as the hierarchical control system in MARS. With the unique configuration of power electronics modules in MARS, it becomes necessary to develop custom-designed real-time simulation models in the cHIL setup in absence of off-the-shelf models. In this paper, high-fidelity dynamic model of MARS, control algorithms at the lower level, and required communication algorithms are developed and optimized for real-time performance in the cHIL setup. Real-time experimental results from the cHIL are provided.