Search NASA⌕ Search

SEARCH · Search NASA

Results for “high modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

Thermal High- and Low-Cycle Fatigue Behavior of Thick Thermal Barrier Coating Systems

Ceramic thermal barrier coatings have received increasing attention for advanced gas turbine and diesel engine applications because of their ability to provide thermal insulation to engine components. However, the durability of these coatings under the severe thermal cycling conditions encountered in a diesel engine (ref. 1) still remains a major issue. In this research at the NASA Lewis Research Center, a high-power laser was used to investigate the thermal fatigue behavior of a yttria-stabilized zirconia coating system under simulated diesel engine conditions. The mechanisms of fatigue crack initiation and propagation, and of coating failure under complex thermal low-cycle fatigue (LCF, representing stop/start cycles) and thermal high-cycle fatigue (HCF, representing operation at 1300 rpm) are described. Continuous wave and pulse laser modes were used to simulate pure LCF and combined LCF/HCF, respectively (ref. 2). The LCF mechanism was found to be closely related to the coating sintering and creep at high temperatures. These creep strains in the ceramic coating led to a tensile stress state during cooling, thus providing the major driving force for crack growth under LCF conditions. The combined LCF/HCF tests induced more severe coating surface cracking, microspallation, and accelerated crack growth than did the pure LCF test. HCF thermal loads also facilitated lateral crack branching and ceramic/bond coat interface delaminations. HCF is associated with the cyclic stresses originating from the high-frequency temperature fluctuation at the ceramic coating surface. The HCF thermal loads act on the crack by a wedging mechanism (ref. 1), resulting in continuous crack growth at temperature. The HCF stress intensity factor amplitude increases with the interaction depth and temperature swing, and decreases with the crack depth. HCF damage also increases with the thermal expansion coefficient and the Young's modulus of the ceramic coating (refs. 1 and 3).

Miller, Robert A.↗

Failure Analysis and Recovery of a 50-mm Highly Elastic Intermetallic NiTi Ball Bearing for an ISS Application

Ball bearings used inside the ISS Distillation Assembly centrifuge require superior corrosion and shock resistance to withstand acidic wastewater exposure and heavy spacecraft launch related loads. These requirements challenge conventional steel bearings and provide an ideal pathfinder application for 50-mm bore, deep-groove ball bearings made from the corrosion immune and highly elastic intermetallic material 60NiTi. During early ground testing in 2014 one 60NiTi bearing unexpectedly and catastrophically failed after operating for only 200 hr. A second bearing running on the same shaft was completely unaffected. An investigation into the root cause of the failure determined that an excessively tight press fit of the bearing outer race coupled with NiTi's relatively low elastic modulus were key contributing factors. The proposed failure mode was successfully replicated by experiment. To further corroborate the root cause theory, a successful bearing life test using improved installation practices (selective fitting) was conducted. The results show that NiTi bearings are suitable for space applications provided that care is taken to accommodate their unique material characteristics.

DellaCorte, Christopher↗

Elastic relaxations associated with the Pm3m-R3c transition in LaA103 III: superattenuation of acoustic resonances

Resonant Ultrasound Spectroscopy has been used to characterize elastic softening and a variety of new acoustic dissipation processes associated with the Pm{bar 3}m {leftrightarrow} R{bar 3}c transition in single crystal and ceramic samples of LaAlO{sub 3}. Softening of the cubic structure ahead of the transition point is not accompanied by an increase in dissipation but follows different temperature dependences for the bulk modulus, 1/3(C{sub 11} + 2C{sub 12}), and the shear components 1/2(C{sub 11}-C{sub 12}) and C{sub 44} as if the tilting instability contains two slightly different critical temperatures. The transition itself is marked by the complete disappearance of resonance peaks (superattenuation), which then reappear below {approx}700 K in spectra from single crystals. Comparison with low frequency, high stress data from the literature indicate that the dissipation is not due to macroscopic displacement of needle twins. An alternative mechanism, local bowing of twin walls under low dynamic stress, is proposed. Pinning of the walls with respect to this displacement process occurs below {approx}350 K. Anelasticity maps, analogous to plastic deformation mechanism maps, are proposed to display dispersion relations and temperature/frequency/stress fields for different twin wall related dissipation mechanisms. An additional dissipation process, with an activation energy of 43 {+-} 6 kJ.mole{sup -1}, occurs in the vicinity of 250 K. The mechanism for this is not known, but it is associated with C{sub 44} and therefore appears to be related in some way to the cubic {leftrightarrow} rhombohedral transition at {approx}817 K. Slight softening in the temperature interval {approx}220 {yields} 70 K of resonance peaks determined by shear elastic constants hints at an incipient E{sub g} ferroelastic instability in LaAlO{sub 3}. The softening interval ends with a further dissipation peak at {approx} 60 K, the origin of which is discussed in terms of freezing of atomic motions of La and/or Al away from their high symmetry positions in the R{bar 3}c structure. LaAlO{sub 3} thus shows evidence of incipient instabilities at low temperatures which is potentially analogous with the phenomenologically rich behavior of SrTiO{sub 3}.

36 MATERIALS SCIENCE↗

Application of a Multiscale Model of Tantalum Deformation at Megabar Pressures

A new multiscale simulation tool has been developed to model the strength of tantalum under high-pressure dynamic compression. This new model combines simulations at multiple length scales to explain macroscopic properties of materials. Previously known continuum models of material response under load have built upon a mixture of theoretical physics and experimental phenomenology. Experimental data, typically measured at static pressures, are used as a means of calibration to construct models that parameterize the material properties; e.g., yield stress, work hardening, strain-rate dependence, etc. The pressure dependence for most models enters through the shear modulus, which is used to scale the flow stress. When these models are applied to data taken far outside the calibrated regions of phase space (e.g., strain rate or pressure) they often diverge in their predicted behavior of material deformation. The new multiscale model, developed at Lawrence Livermore National Laboratory, starts with interatomic quantum mechanical potential and is based on the motion and multiplication of dislocations. The basis for the macroscale model is plastic deformation by phonon drag and thermally activated dislocation motion and strain hardening resulting from elastic interactions among dislocations. The dislocation density, {rho}, and dislocation velocity, {nu}, are connected to the plastic strain rate {var_epsilon}{sup p}, via Orowan's equation: {var_epsilon}{sup p} = {rho}b{nu}/M, where b is the Burger's vector, the shear magnitude associated with a dislocation, and M is the Taylor factor, which accounts for geometric effects in how slip systems accommodate the deformation. The evolution of the dislocation density and velocity is carried out in the continuum model by parameterized fits to smaller scale simulations, each informed by calculations on smaller length scales down to atomistic dimensions. We apply this new model for tantalum to two sets of experiments and compare the results with more traditional models. The experiments are based on the Barnes's technique in which a low density material loads against a metal surface containing a pre-imposed rippled pattern. The loaded sample is Rayleigh-Taylor unstable and the rippled amplitudes grow with time. The rate of growth differs depending on the material strength, with stronger materials growing less, even to the point of saturation. One set of experiments was conducted at the pRad facility at LANSCE at Los Alamos National Laboratory in 2007 using high-explosive (HE) driven tantalum samples. The other set of experiments was done at the Omega laser at the Laboratory for Laser Energetics at the University of Rochester, which used high-powered lasers to create plasmas to dynamically compress a rippled tantalum sample. The two techniques provide data at different pressures and strain rates: The HE technique drives the samples at around 2 x 10{sup 5} s{sup -1} strain rate and pressures near 500 kbar, while the laser technique hits strain rates around 2 x 10{sup 7} s{sup -1} and pressures close to 1.4 Mbar. The most recent laser experiments were conducted in February 2010 and they present a sample of the data in Figure 1, which shows a face-on radiograph at a time of 65 ns after the laser was turned on. From this radiograph, they measure the growth factor which is defined to be the change in amplitude of the ripples relative to their initial amplitude. Figure 2 shows the resulting growth factors along with various model fits. The error bars are typically 20-25%. Only the multiscale model predictions match the experimental measurements. The growth factors via the HE technique are determined from multiple side-on proton radiography images and thus provide a full growth curve per single experiment. A sample growth curve is shown in Figure 3, also with various model fits and error bars estimated at 25%. It should be noted that by 7.5 {micro}s the growth in this sample has exceeded the initial target thickness indicating that localizations not captured in the overall simulation have probably become dominant, i.e., the target is likely breaking up. Application of the multiscale dislocation dynamics model as implemented in the Ares hydrodynamics code shows excellent agreement with both the pRad and Omega data. They also compare the Steinberg-Lund (SL), Preston-Tonks-Wallace (PTW), and Stainberg-Guinan (SG) models with the data. The PTW and SG models provide good fits to the pRad data but over-predict the growth (underestimate the strength) on the laser platform. The SL model under-predicts the pRad data and over-predicts the Omega data. The excellent agreement of the multiscale model with the data over two orders of magnitude in strain rate and more than a factor of two in pressure lends credibility to the model. They continue to stress the model by conducting experiments at 5 Mbars and beyond at the National Ignition Facility at LLNL in the near future.

36 MATERIALS SCIENCE↗

High-pressure single-crystal X-ray diffraction of Tl{sub 2}SeO{sub 4}

The effect of pressure on the crystal structure of thallium selenate (Tl{sub 2}SeO{sub 4}) (Pmcn, Z=4), containing the Tl{sup +} cations with electron lone pairs, has been studied with single-crystal X-ray diffraction in a diamond anvil cell up to 3.64 GPa at room temperature. No phase transition has been observed. The compressibility data are fitted by a Murnaghan equation of state with the zero-pressure bulk modulus B{sub 0}=29(1) GPa and the unit-cell volume at ambient pressure V{sub 0}=529.6(8) A{sup 3} (B'=4.00). Tl{sub 2}SeO{sub 4} is the least compressible in the c direction, while the pressure-induced changes of the a and b lattice parameters are quite similar. These observations can be explained by different pressure effects on the nine- and 11-fold coordination polyhedra around the two non-equivalent Tl atoms. The SeO{sub 4}{sup 2-} tetrahedra are not rigid units and become more distorted. Their contribution to the compressibility is small. The effect of pressure on the isotypical oxide materials A{sub 2}TO{sub 4} with the {beta}-K{sub 2}SO{sub 4} structure is discussed. It appears that the presence of electron lone pairs on the Tl{sup +} cation does not seem to influence the compressibility of Tl{sub 2}SeO{sub 4}. - Graphical abstract: Pressure dependence of normalized lattice parameters and unit-cell volumes in Tl{sub 2}SeO{sub 4} (Pmcn, Z=4). The solid line is the Murnaghan equation of state.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Durable aluminate toughened zirconate composite thermal barrier coating (TBC) materials for high temperature operation

Research on advanced thermal barrier coating (TBC) materials capable of operating beyond 1200°C has primarily focused on the rare earth zirconate pyrochlores, particularly gadolinium zirconate (Gd 2 Zr 2 O 7 – GZO). The drawback of this material is a significant reduction in durability due to a low fracture toughness. This study investigates utilization of a thermodynamically compatible gadolinia alumina perovskite (GdAlO 3 – GAP) toughening phase to improve the durability of GZO. Dense pellets were fabricated to assess the material properties with minimal microstructural influence. Thermal stability, elastic modulus, hardness, indentation fracture resistance and erosion durability were evaluated for GZO, GAP, and composite pellets containing 10, 30, and 50 wt.% GAP. It was demonstrated that GAP and GZO are thermodynamically compatible through 1600°C and thus capable of operating well beyond the limits of traditional 7 wt.% yttria stabilized zirconia (YSZ). Grain sizes are maintained due to a lack of diffusion, and thus microstructural stability is enhanced. The GAP fracture toughness was shown to be over 2X that of GZO while exhibiting a lower elastic modulus and similar hardness. The 50:50 GZO-GAP composite exhibited a 63% reduction in the absolute erosion rate, demonstrating the immense toughening capabilities of this system. The implications for composite TBCs utilizing this system are discussed, along with future research.

36 MATERIALS SCIENCE↗

Viscoelastic properties of addition-cured polyimides used in high temperature polymer matrix composites

Viscoelastic properties of the addition cured polyimide, PMR-15, were studied using dynamic mechanical and stress relaxation tests. For temperatures below the glass transition temperature, T sub g, the dynamic mechanical properties measured using a temperature scan rate of 10 C/min were strongly affected by the presence of absorbed moisture in the resin. Dynamic mechanical properties measured as a function of time during an isothermal hold provided an indication of chemical changes occurring in the resin. For temperatures above (T sub g + 20 C), the storage modulus increased continuously as a function of time indicating that additional crosslinking is occurring in the resin. Because of these changes in chemical structures, the stress relaxation modulus could not be measured over any useful time interval for temperatures above T sub g. For temperatures below T sub g, dynamic mechanical properties appeared to be unaffected by chemical changes for times exceeding 1 hr. Since the duration of the stress relaxation tests was less than 1 hr, the stress relaxation modulus could be measured. As long as the moisture content of the resin was less than 2 pct, stress relaxation curves measured at different temperatures could be superimposed using horizontal shifts along the log(time) axis with only small shifts along the vertical axis.

Roberts, Gary D↗

Structural stability and compressibility of group IV transition metals-based bulk metallic glasses under high pressure

High-pressure x-ray diffraction studies have been carried out on the two group IV transition metals-based bulk metallic glasses (BMGs) Zr{sub 57}Cu{sub 15.4}Ni{sub 12.6}Al{sub 10}Nb{sub 5} and Ti{sub 42}Zr{sub 24}Cu{sub 15.5}Ni{sub 14.5}Be{sub 4} to a pressure of 30 GPa at ambient temperature in a diamond anvil cell. Image plate x-ray diffraction studies under high pressure were carried out at a synchrotron source and the two BMG diffraction bands can be followed to the highest pressure using an internal copper pressure standard. The amorphous phase is observed to be stable to the highest static pressure of 30 GPa suggesting that the phase change observed in dynamical pressure experiments is related to an increase in temperature. The measured bulk modulus (B{sub 0}) and its pressure derivative (B') are 118 GPa and 3.11 for Zr-based BMG and 116 GPa and 2.84 for Ti-based BMG. The measured bulk modulus for BMG's by x-ray diffraction technique is consistent with the ultrasonic measurements. The decompression data reveal an increase in density by 3%-4% at ambient condition after pressure cycling to 30 GPa indicating reduction in excess free volume.

36 MATERIALS SCIENCE↗

Opto-mechano-fluidic viscometer

The recent development of opto-mechano-fluidic resonators has provided—by harnessing photon radiation pressure—a microfluidics platform for the optical sensing of fluid density and bulk modulus. Here, we show that fluid viscosity can also be determined through optomechanical measurement of the vibrational noise spectrum of the resonator mechanical modes. A linear relationship between the spectral linewidth and root-viscosity is predicted and experimentally verified in the low viscosity regime. Our result is a step towards multi-frequency measurement of viscoelasticity of arbitrary fluids, without sample contamination, using highly sensitive optomechanics techniques.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

FFT-based model for irradiated aggregate microstructures in concrete

The concrete biological shield of light water reactors is exposed to neutron and gamma irradiation throughout its lifetime, which results in the long-term degradation of the concrete’s mechanical properties. Under neutron irradiation, the concrete’s aggregates are subjected to radiation-induced volumetric expansion (RIVE), which strongly depends on the mineral content of the aggregate and exhibits the largest expansion in silicate-bearing minerals. In this work, the authors used the fast Fourier transform-based code Microstructure-Oriented Scientific Analysis of Irradiated Concrete (MOSAIC) in 2D to model the expansion of five different aggregates provided by the Japan Concrete Aging Management Program (JCAMP). Comparable rock specimens were irradiated at the JEEP-II test reactor. The model uses realistic aggregate microstructure reconstruction based on high-resolution characterization images. The model accounts for anisotropic RIVE, thermal expansion, and the associated initiation and propagation of damage. The RIVE models are calibrated based on expansion data in the literature. The authors assume that damage occurs exclusively at interfaces between the particles that compose an aggregate and that these interfaces also exhibit swelling. Using a micromechanical model, the evolution of Young’s modulus with RIVE is calculated for each aggregate and compared with Russian irradiation data. The modeled linear expansion agrees well with the experimentally measured expansion. Furthermore, the model also predicts that anisotropic RIVE and thermal expansion result in an earlier onset of damage with neutron fluence than in the isotropic case.

36 MATERIALS SCIENCE↗

Processing of sintered alpha SiC

Processing methods of sintered alpha SiC for engine applications are developed in a cost effective manner, using a submicron sized powder blended with sintering aids (boron and carbon). The processes for forming a green powder compact, such as dry pressing, cold isostatic pressing and green machining, slip casting, aqueous extrusion, plastic extrusion, and injection molding, are described. Dry pressing is the simplest route to component fabrication, and is carried out at approximately 10,000 psi pressure, while in the cold isostatic method the pressure could go as high as 20,000 psi. Surfactants are added to control settling rates and casting characteristics in the slip casting. The aqueous extrusion process is accomplished by a hydraulic ram forcing the aqueous mixture through a die. The plastic forming processes of extrusion and injection molding offer the potential of greater diversity in shape capacity. The physical properties of sintered alpha SiC (hardness, Young's modulus, shear modulus, and thermal diffusivity) are extensively tested. Corrosion resistance test results of silicon carbide are included.

Storm, R. S.↗

Theory of the spin-1 bosonic liquid metal - Equilibrium properties of liquid metallic deuterium

The theory of a two-component quantum fluid comprised of spin-1/2 fermions and nonzero spin bosons is examined. This system is of interest because it embodies a possible quantum liquid metallic phase of highly compressed deuterium. Bose condensation is assumed present and the two cases of nuclear-spin-polarized and -unpolarized systems are considered. A significant feature in the unpolarized case is the presence of a nonmagnetic mode with quadratic dispersion owing its existence to nonzero boson spin. The physical character of this mode is examined in detail within a Bogoliubov approach. The specific heat, bulk modulus, spin susceptibility, and thermal expansion are all determined. Striking contrasts in the specific heats and thermal-expansion coefficients of the liquid and corresponding normal solid metallic phase are predicted.

Oliva, J.↗

Fiber Optic Sensors for Cure/Health Monitoring of Composite Materials

The objective of the current program is to develop techniques for using optical fibers to monitor the cure of composite materials in real time during manufacture and to monitor the in-service structural health of composite structures. Single and multimode optical fibers containing Bragg gratings have been used to perform Near Infrared (NIR) spectroscopy on high refractive index resins and show promise as embedded sensors. In order for chemical spectroscopy to be possible, intimate contact must be achieved between the fiber core and the composite resin. This contact is often achieved by stripping the cladding off of a portion of the fiber, thus making it brittle and easily broken in the composite processing environment. To avoid weakening the fiber to this extent, high refractive index fibers have been fabricated that use a low refractive index acrylate coating which serves as the cladding. This is ideal, as the coating is easily solvent stripped and intimate contact with the glass core can be achieved. Real time resin and composite chemical spectra have been obtained, with possible multifunctional capability using Bragg gratings to assess physical properties such as strain, modulus and other parameters of interest.

Wood, K. H.↗

Surface-modified and oven-dried microfibrillated cellulose reinforced biocomposites: Cellulose network enabled high performance

Microfibrillated cellulose (MFC) is widely used as a reinforcement filler for biocomposites due to its unique properties. However, the challenge of drying MFC and the incompatibility between nanocellulose and polymer matrix still limits the mechanical performance of MFC-reinforced biocomposites. In this study, we used a water-based transesterification reaction to functionalize MFC and explored the capability of oven-dried MFC as a reinforcement filler for polylactic acid (PLA). Remarkably, this oven-dried, vinyl laurate–modified MFC improved the tensile strength by 38 % and Young’s modulus by 71 % compared with neat PLA. Our results suggested improved compatibility and dispersion of the fibrils in PLA after modification. This study demonstrated that scalable water-based surface modification and subsequent straightforward oven drying could be a facile method for effectively drying cellulose nanomaterials. We find that the method helps significantly disperse fibrils in polymers and enhances the mechanical properties of microfibrillar cellulose-reinforced biocomposites.

36 MATERIALS SCIENCE↗

Constraining the high-density behavior of the nuclear equation of state from strangeness production in heavy-ion collisions

The dynamics of pions and strange particles in heavy-ion collisions in the region of 1A GeV energies is investigated by the lanzhou quantum molecular dynamics model for probing the nuclear equation of state at suprasaturation densities. The total multiplicities and the ratios obtained in {sup 197}Au+{sup 197}Au over {sup 12}C+{sup 12}C systems are calculated for selected Skyrme parameters SkP, SLy6, Ska, and SIII, which correspond to different modulus of incompressibility of symmetric nuclear matter and different cases of the stiffness of symmetry energy. A decreasing trend of the excitation functions of the ratios for strange particle production with increasing incident energy was observed. The available data of K{sup +} production measured by KaoS collaboration are described well with the parameter SkP, which results in a soft equation of state. The conclusions cannot be modified by an in-medium kaon-nucleon potential.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Rheological and pumping behaviour of 3D printable cementitious materials with varying aggregate content

3D printing with cementitious materials is an emerging technology and provides an active area of research. Despite this, there are only limited studies that examine the pumping behaviour of high yield stress fluids such as printable concrete. We present a study on the rheological behaviour of 3D printable cementitious materials with different aggregate-to-binder ratios (a/b) and analyse the pumping and printing characteristics with the measured rheological parameters. We observed that an increase in a/b resulted in a significant increase of plastic viscosity, and a nominal increase in yield stress and storage modulus. The variation in plastic viscosity and yield stress with increasing aggregate content was analysed with the Krieger-Dougherty and Chateau-Ovarlez-Trung model, respectively. Also, the rheological properties of the paste rich lubrication layer during pumping were determined with the help of a tribometer. The yield stress and viscous constant of the lubrication layer increase with the increase in a/b. The pumping pressure predictions were carried out by a suitable theoretical model by considering appropriate flow conditions for different mixtures. The variation in critical height of printed elements with an increase in a/b was correlated with the observed rheological parameters.

36 MATERIALS SCIENCE↗

A theoretical study of solid solution strengthening in the refractory medium entropy alloy Nb 45 Ta 25 Ti 15 Hf 15

The refractory medium-entropy alloy (RMEA) Nb 45 Ta 25 Ti 15 Hf 15 exhibits exceptional tensile ductility and fracture toughness at ambient temperature, but its engineering applications are limited by a lack of high temperature strength. Using a machine-learning interatomic potential (MLIP) with near-density functional theory (DFT) accuracy, we conducted molecular dynamics (MD) and statics simulations of the behavior of dislocations with both screw and edge characters. We also analyze experimentally measured yield strengths using the Rao-Suzuki model and the Maresca-Curtin model modified to include a temperature-dependent shear modulus and a bulk modulus-dependent misfit volume, thereby uncovering the mechanisms underlying the yielding of this RMEA. Compared with the published experimental yield strength, the models parameterized by the MLIP effectively reproduce the experimental results over a wide temperature range. The models and MD simulations indicate that yielding is governed by screw dislocations, with dipole dragging as the dominant mechanism. In MD simulations, we observed a potential softening mechanism not considered by the Rao-Suzuki screw model: slow migration of interstitial jogs along the dislocation core, which could lead to the annihilation of vacancy and interstitial jog pairs by their combination.

BCC complex concentrated alloys↗