Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

Magnetic Sorbent for the Removal of Selenium(IV) from Simulated Industrial Wastewaters: Determination of Column Kinetic Parameters

A novel meso- and microporous tire-derived-carbon support with magnetic iron oxide nanoparticle adsorbents that selectively adsorbs Se(IV) ions from simulated contaminated water has been developed. In this work, the physicochemical characteristics of the composite adsorbent are characterized with respect to porosity and surface area, chemical composition, and microstructure morphology. The kinetics of this composite adsorbent in a fixed-bed setting has been determined. Several column runs were conducted and analyzed by inductively coupled plasma-optical emission spectroscopy (ICP-OES) to determine the concentration gradient vs time. These results were then fit to a pseudo-second order rate law to obtain equilibrium values. Combining calculated equilibrium values with effluent concentration data, enabled the application of the Adams–Bohart model to determine reaction constants and column coefficients. Column parameters obtained from different flow rates and fittings of the Adams–Bohart model were remarkably consistent. These findings enable the application of this sorbent to fixed-bed column systems and opens up further research into mixed pollutants tests with real wastewater and scaling of selenium pollutant removal.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Study on Vitrification for LLW Radioactive Wastes - 16235

Ash and ion exchange resin wastes to be vitrified were considered among various radioactive wastes in the Japanese nuclear industry. The appropriate glass composition for the waste is calculated using the computer program. The glass composition is systematically studied using a ternary diagram, considering viscosity, electrical conductivity, and durability. The optimized glass composition based on calculated parameters of vitrification process and the convenience of mixing wastes is selected for crucible experiment. Since differences between calculated values and measured values may occur upon evaluation of glass formulations using glass formulation computer simulation program, the calculated glass formulations should be verified through experiments on a laboratory scale for more meticulous development of glass formulations. For the follow-up development of glass formulations, several glass formulations are planned to be developed. The candidate glasses for treatment of ash and ion exchange resin were melted and fabricated using reagents, respectively. The chemicals were weighed out to produce the desired batch compositions and mixed thoroughly and then put into clay crucibles for melting. Next, the crucibles were introduced into an electric furnace at 1,150 deg. C in the ambient atmosphere and pressure with occasional stirring by a quartz rod. A hold time of 1 hour was introduced to promote homogenization. Finally, the melted material was poured on a graphite plate to be rapidly cooled. The viscosities of all fabricated glasses were in the desired range. After rapid cooling, the micro-structure of the glasses was analyzed using the SEM. They exhibited amorphous structure with good homogeneity. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Processing Parameter Effects on Residual Stress and Mechanical Properties of Selective Laser Melted Ti6Al4V

Selective laser melting (SLM) process is characterized by large temperature gradients resulting in high levels of residual stress within the additively manufactured metallic structure. SLM-processed Ti6Al4V yields a martensitic microstructure due to the rapid solidification and results in a ductility generally lower than a hot working equivalent. Post-process heat treatments can be applied to SLM components to remove in-built residual stress and improve ductility. Residual stress buildup and the mechanical properties of SLM parts can be controlled by varying the SLM process parameters. This investigation studies the effect of layer thickness on residual stress and mechanical properties of SLM Ti6Al4V parts. This is the first-of-its kind study on the effect of varying power and exposure in conjunction with keeping the energy density constant on residual stress and mechanical properties of SLM Ti6Al4V components. It was found that decreasing power and increasing exposure for the same energy density lowered the residual stress and improved the % elongation of SLM Ti6Al4V parts. Increasing layer thickness resulted in lowering the residual stress at the detriment of mechanical properties. The study is based on detailed experimental analysis along with finite element simulation of the process using ABAQUS to understand the underlying physics of the process.

36 MATERIALS SCIENCE↗

Behavioral simulations and experimental evaluations of stress induced spatial nonuniformity of dynamic bulk modulus in additive friction stir deposited AA 6061

Additive friction stir deposition (AFSD) is a rapidly developing solid-state additive manufacturing (AM) technology that enables the fabrication of customized products on a relatively large scale. The unique forge-liked process offers high quality products with refined equiaxed microstructure and exceptional mechanical performance. However, in AFSD, the spatially distributed mechanical properties within a deposited layer have not been established so far, due to the lack of a suitable large-scale mapping method. In the present work, an ultrasonic dynamic-elasticity mapping method was employed to map the distribution of physical properties in a AFSD 6061 Al. Strong spatial asymmetries in elastographies were mainly due to the residual stresses. The origin of the asymmetries was investigated through thermo-mechanical simulations of the AFSD process. It was observed that majority of the asymmetries were associated with the mechanical residual stresses instead of the symmetric thermal residual stresses during linear deposition of the AFSD process. However, the thermal residual stresses can be manipulated to become asymmetric with a 90° turn in the linear deposition path, due to the difference between the levels of cooling along the edges of the inner and outer corners. Hence, the mechanical and thermo-mechanical residual stresses can be additive or subtractive depending on the direction of the turns. Here, such numerically predicted behaviors were also experimentally observed on the AFSD fabricated samples by ultrasonic elastography. Furthermore, additional preliminary studies on multi-layer AFSD fabrications show the asymmetric mechanical stresses generated during the deposition process on different layers generate constructive or destructive interference which results to spatially variable dynamic bulk modulus depending on the deposition orientations of layers.

36 MATERIALS SCIENCE↗

Critical role of slags in pitting corrosion of additively manufactured stainless steel in simulated seawater

Abstract Pitting corrosion in seawater is one of the most difficult forms of corrosion to identify and control. A workhorse material for marine applications, 316L stainless steel (316L SS) is known to balance resistance to pitting with good mechanical properties. The advent of additive manufacturing (AM), particularly laser powder bed fusion (LPBF), has prompted numerous microstructural and mechanical investigations of LPBF 316L SS; however, the origins of pitting corrosion on as-built surfaces is unknown, despite their utmost importance for certification of LPBF 316L SS prior to fielding. Here, we show that Mn-rich silicate slags are responsible for pitting of the as-built LPBF material in sodium chloride due to their introduction of deleterious defects such as cracks or surface oxide heterogeneities. In addition, we explain how slags are formed in the liquid metal and deposited at the as-built surfaces using high-fidelity melt pool simulations. Our work uncovers how LPBF changes surface oxides due to rapid solidification and high-temperature oxidation, leading to fundamentally different pitting corrosion mechanisms.

36 MATERIALS SCIENCE↗

Understanding Complex Magnetic Spin Textures with Simulation-Assisted Lorentz Transmission Electron Microscopy

There is an increased interest in topologically nontrivial magnetic spin textures such as skyrmions and chiral domain-wall solitons, both from a point of fundamental physics understanding as well as potential technological interest in low-power memory applications. In order to control their behavior, it is necessary to understand their complex spin texture at the nanoscale. Lorentz transmission electron microscopy (LTEM) is a suitable technique for studying these systems due to its high spatial resolution and capability to simultaneously characterize magnetic texture and microstructure. In this work, we present the application of PyLorentz, an open-source software suite that we have developed, for quantitative image analysis of Neel-type skyrmions in thin-film heterostructures. PyLorentz enhances LTEM capabilities by enabling reconstruction of magnetic induction maps from experimental images, as well as simulating LTEM images using micromagnetic simulation data. We demonstrate this for simulated Neel skyrmions as well as experimental data from [Pt/Co/W] multilayer heterostructures. Finally, we also show how simulation-assisted LTEM analysis is crucial for understanding these complex magnetic spin textures, in which the reconstructed magnetic induction map (seen in the LTEM images) differs significantly from the magnetization configuration.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Development of a Laser Ultrasonics-based Approach for Rapid Screening of High Entropy Alloys

This project utilized a laser ultrasonic technique to systematically study temperature-induced evolution of material properties in a set of interrelated binary alloys and a high entropy alloy (HEA) fabricated using arc-melting and spark plasma sintering processes. This technique involved the use of a nanosecond duration, high-intensity pulsed laser to thermo-elastically generate ultrasonic waves that propagate in the bulk of the metal alloy. Sub-nanometer-scale displacements associated with the propagating bulk ultrasonic waves were detected along the epicenter on the opposite surface of the sample using a 1 GHz bandwidth photorefractive interferometer. Phase transformations and microstructural changes were inferred from the temperature-dependent trends in the bulk acoustic velocities and features in the ultrasonic epicentral waveforms measured in the binary alloys. These inferences were then correlated with electron/optical microscopy observations and predictions using calculations of phase diagrams (CALPHAD). The results showed that the laser-generated ultrasonic pulses were strongly influenced by changes in material microstructure and could accurately track thermally driven phase transformations and detect the presence of microscale heterogeneities (grain boundaries, dendritic structures, etc.) in the set of binary alloy samples. The measurement approach was then applied to a quinary HEA sample for estimating phase transition temperature and determining microstructural heterogeneity. The rapid, non-contact and non-destructive ultrasonic testing approach demonstrated here is amenable to high throughput combinatorial investigations that can be applied to graded composition HEAs produced using advanced manufacturing methods. When paired with atomistic simulations and CALPHAD modeling, this approach can overcome the bottlenecks faced by current material characterization methods in efficiently screening the vast discovery space of HEAs that spans over a hundred million unique quinary alloy compositions.

36 MATERIALS SCIENCE↗

Quench process modeling & simulation in the heat-treatment of critical aerospace components

To manufacture light-weight, advanced metal alloy components for gas turbine engines, quench heat-treatment processes are typically used. By quenching the component from elevated temperatures, the alloy sometimes undergoes a solid-state phase transformation which produces special microstructures with the required, enhanced mechanical properties. However, the quenching can also lead to cracks forming in the component. Addressing the quench cracking problems adds a significant burden to the cost, schedule, and energy demand of manufacture. Currently, optimizing the quench process to mitigate or avoid the cracking is performed largely by trial-and-error, relying heavily on costly experimental (thermocouple)trials to understand the local thermal gradients which cause the cracks to form. In this first part (Phase 1) of the work, high-performance computing is employed to establish the ability of modern CFD (computational fluid dynamics) to alleviate or wholly replace the experimental quenching trials by virtual testing. A Baseline CFD model is defined and its accuracy established to be comparable to(and which usually exceeds) the accuracy of existing HTC (heat-transfer coefficient) based simulation methods of quenching. As a first-principles based approach, “calibration” of the Baseline CFD model is independent of the quench process itself, but instead relies on the accuracy of the underlying (modeled),generic two-phase fluid processes which cannot be currently resolved by CFD for large, industrial-scale cases. A novel, high-fidelity DNS capability has been developed and verified to examine and further improve upon the mean-field closure submodels on which the Baseline CFD approach is based.1

99 GENERAL AND MISCELLANEOUS↗

X-ray Scattering and Coarse-Grained Simulations for Clustering and Interactions of Monoclonal Antibodies at High Concentrations

Attractive protein-protein interactions (PPI) in concentrated monoclonal antibody (mAb) solutions may lead to reversible oligomers (clusters) that impact colloidal stability and viscosity. Herein, the PPI are tuned for two mAbs via the addition of arginine (Arg), NaCl, or ZnSO 4 as characterized by the structure factor ( S eff (q)) with small angle x-ray scattering (SAXS). The SAXS data are fit with molecular dynamics simulations by placing a physically relevant short-ranged attractive interaction on selected beads in coarse-grained 12 bead models of the mAb shape. The optimized 12-bead models are then used to differentiate key microstructural properties, including center of mass radial distribution functions ( g COM (r)), coordination numbers and cluster size distributions (CSD). The addition of co-solutes results in more attractive Seff(q) relative to the no co-solute control for all systems tested, with the most attractive systems showing an upturn at low q . Only the All1 model with an attractive site in each Fab and Fc region (possessing Fab-Fab, Fab-Fc and Fc-Fc interactions) can reproduce this upturn, and the corresponding CSDs show the presence of larger clusters compared to the control. In general, for models with similar net attractions, i.e., second osmotic virial coefficients, the size of the clusters increases as the attraction is concentrated on a smaller number of evenly distributed beads. Here, the cluster size distributions from simulations are used to improve the understanding and prediction of experimental viscosities. The ability to discriminate between models with bead interactions at particular Fab and Fc bead sites from SAXS simulations, and to provide real space properties (CSD and g COM (r)), will be of interest in engineering protein sequence and formulating protein solutions for weak PPI to minimize aggregation and viscosities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fuel Efficient Diesel Particulate Filter (DPF) Modeling and Development

The project described in this report seeks to promote effective diesel particulate filter technology with minimum fuel penalty by enhancing fundamental understanding of filtration mechanisms through targeted experiments and computer simulations. The overall backpressure of a filtration system depends upon complex interactions of particulate matter and ash with the microscopic pores in filter media. Better characterization of these phenomena is essential for exhaust system optimization. The acicular mullite (ACM) diesel particulate filter substrate is under continuing development by Dow Automotive. ACM is made up of long mullite crystals which intersect to form filter wall framework and protrude from the wall surface into the DPF channels. ACM filters have been demonstrated to effectively remove diesel exhaust particles while maintaining relatively low backpressure. Modeling approaches developed for more conventional ceramic filter materials, such as silicon carbide and cordierite, have been difficult to apply to ACM because of properties arising from its unique microstructure. Penetration of soot into the high-porosity region of projecting crystal structures leads to a somewhat extended depth filtration mode, but with less dramatic increases in pressure drop than are normally observed during depth filtration in cordierite or silicon carbide filters. Another consequence is greater contact between the soot and solid surfaces, which may enhance the action of some catalyst coatings in filter regeneration. The projecting crystals appear to provide a two-fold benefit for maintaining low backpressures during filter loading: they help prevent soot from being forced into the throats of pores in the lower porosity region of the filter wall, and they also tend to support the forming filter cake, resulting in lower average cake density and higher permeability. Other simulations suggest that soot deposits may also tend to form at the tips of projecting crystals due to the axial velocity component of exhaust moving down the filter inlet channel. Soot mass collected in this way would have a smaller impact on backpressure than soot forced into the flow restrictions deeper in the porous wall structure. This project has focused on the development of computational, analytical, and experimental techniques that are generally applicable to a wide variety of exhaust aftertreatment technologies. By helping to develop improved fundamental understanding pore-scale phenomena affecting filtration, soot oxidation, and NOX abatement, this cooperative research and development agreement (CRADA) has also assisted Dow Automotive in continuing development and commercialization of the ACM filter substrate. Over the course of this research project, ACM filters were successfully deployed on the Audi R10 TDI racecar which won the 24 Hours of LeMans endurance race in 2006, 2007, and 2008; and the 12 Hours of Sebring endurance race in 2006 and 2007. It would not have been possible for the R10 to compete in these traditionally gasoline-dominated events without reliable and effective exhaust particulate filtration. These successes demonstrated not only the performance of automotive diesel engines, but the efficacy of DPF technology as it was being deployed around the world to meet new emissions standards on consumer vehicles. During the course of this CRADA project, Dow Automotive commercialized their ACM DPF technology under the AERIFYTM DPF brand.

33 ADVANCED PROPULSION SYSTEMS↗

Optimization of chemical compositions in low-carbon Al-killed enamel steel produced by ultra-fast continuous annealing

The influence of Mn,S and B contents on microstructural characteristics, mechanical properties and hydrogen trapping ability of low-carbon Al-killed enamel steel was investigated. The materials were produced and processed in a laboratory and the ultra-fast continuous annealing processing was performed using a continuous annealing simulator. It was found that increasing Mn,S contents in steel can improve its hydrogen trapping ability which is attributed by refined ferrite grains, more dispersed cementite and added MnS inclusions. Nevertheless, it deteriorates mechanical properties of steel sheet. Addition of trace boron results in both good mechanical properties and significantly improved hydrogen trapping ability. The boron combined with nitrogen segregating at grain boundaries, cementite and MnS inclusions, provides higher amount of attractive hydrogen trapping sites and raises the activation energy for hydrogen desorption from them. - Highlights: • We study microstructures and properties in low-carbon Al-killed enamel steel. • Hydrogen diffusion coefficients are measured to reflect fish-scale resistance. • Manganese improves hydrogen trapping ability but decrease deep-drawing ability. • Boron improves both hydrogen trapping ability and deep-drawing ability. • Both excellent mechanical properties and fish-scale resistance can be matched.

36 MATERIALS SCIENCE↗

Influence of Local Inhomogeneity of Thermomechanical Treatment Conditions on Microstructure Evolution in Aluminum Alloys

The influence of local inhomogeneity of the stress–strain condition on structure and texture evolution during thermomechanical treatment of aluminum alloys is studied in this work. For this purpose, laboratory rolling and plane strain tests that simulated roughing mill thermomechanical modes were performed. For all processes, the local inhomogeneity of structure evolution was estimated. For this purpose, x-ray texture analysis, EBSD and optical microscopy were used. Additionally, the calculations which allow to evaluate local inhomogeneity of stress–strain conditions for the each process were performed. The experimental results were compared with mathematical simulation output. They indicated structure and texture evolution inhomogeneities, especially during the plane strain and industrial rolling processes. In the plane strain test, typical local deformation zones occurred with different resulting grain size and texture effects than those observed in both rolling processes. This difference was mainly associated with different stress states, strain intensity and strain rate distribution throughout the deformation zone. This study demonstrated that the inhomogeneity of these parameters has a strong impact on structure and texture evolution in the first stage of thermomechanical treatment. In the center layer, laboratory rolling could adequately generate the structure and texture effects observed during rolling of ingots in a commercial mill. Plane strain tests can generate useful results only in the case of adequate choice of sample geometry.

36 MATERIALS SCIENCE↗

Phase-field modeling of the beta to omega phase transformation in Zr–Nb alloys

A three-dimensional elastoplastic phase-field model is developed, using the Finite Element Method (FEM), for modeling the athermal beta to omega phase transformation in Zr–Nb alloys by including plastic deformation and strain hardening of the material. The microstructure evolution during athermal transformation as well as under different stress states, e.g. uni-axial tensile and compressive, bi-axial tensile and compressive, shear and tri-axial loadings, is studied. The effects of plasticity, stress states and the stress loading direction on the microstructure evolution as well as on the mechanical properties are studied. The input data corresponding to a Zr – 8 at.% Nb alloy are acquired from experimental studies as well as by using the CALPHAD method. Our simulations show that the four different omega variants grow as ellipsoidal shaped particles. Our results show that due to stress relaxation, the athermal phase transformation occurs slightly more readily in the presence of plasticity compared to that in its absence. The evolution of omega phase is different under different stress states, which leads to the differences in the mechanical properties of the material. The variant selection mechanism, i.e. formation of different variants under different stress loading directions, is also nicely captured by our model.

36 MATERIALS SCIENCE↗

Nanotwin stability in alloyed copper under ambient and cryo-temperature dependent deformation states

Nanometer size grains, solid solution strengthening, low temperatures, and a high density of nanotwins can provide significant strengthening to a material. Nevertheless, under loading the microstructure may evolve altering the effect of grain size, twin density, etc. on this strengthening. In some cases, these effects can be coupled as in detwinning, which is a mechanism for cryogenic grain growth. Here, in this work, a series of copper nanotwinned columnar grains are solid solution alloyed with aluminum and subject to ambient and cryogenic (–196 °C) environments during mechanical indentation, with the influence of alloying on the detwinning evolution studied. Under indentation, at a lower aluminum solute content (2 at.%), the columnar grains bent corresponding to a loss of twins. At a higher aluminum solute content (8 at.%), the grains shear and retain the nanotwins. Atomistic-scale simulations reveal an increase in the incoherent twin boundary velocity with decreasing temperature, but this boundary velocity is reduced with increasing alloy solute content. The coupling of solid solution strengthening and nanotwin stabilization is then used to explain the microstructural stability as a function of indentation at different temperature conditions.

36 MATERIALS SCIENCE↗

Wire arc additive manufactured A36 steel performance for marine renewable energy systems

Additive manufacturing has established itself to be advantageous beyond small-scale prototyping, now supporting full-scale production of components for a variety of applications. Despite its integration across industries, marine renewable energy technology is one largely untapped application with potential to bolster clean energy production on the global scale. Wave energy converters (WEC) are one specific facet within this realm that could benefit from AM. As such, wire arc additive manufacturing (WAAM) has been identified as a practical method to produce larger scale marine energy components by leveraging cost-effective and readily available A36 steel feedstock material. The flexibility associated with WAAM can benefit production of WEC by producing more complex structural geometries that are challenging to produce traditionally. Additionally, for large components where fine details are less critical, the high deposition rate of WAAM in comparison to traditional wrought techniques could reduce build times by an order of magnitude. In this context of building and supporting WEC, which experience harsh marine environments, an understanding of performance under large loads and corrosive environments must be understood. Hence, WAAM and wrought A36 steel tensile samples were manufactured, and mechanical properties compared under both dry and corroded conditions. Here, the unique microstructure created via the WAAM process was found to directly correlate to the increased ultimate tensile and yield strength compared to the wrought condition. Static corrosion testing in a simulated saltwater environment in parallel with electrochemical testing highlighted an outperformance of corroded WAAM A36 steel than wrought, despite having a slighter higher corrosion rate. Ultimately, this study shows how marine energy systems may benefit from additive manufacturing components and provides a foundation for future applications of WAAM A36 steel.

36 MATERIALS SCIENCE↗

Infrared triggered dwell and active cooling thermal control effects on microstructural uniformity in DED

Directed Energy Deposition (DED) offers rapid large scale fabrication, but difficulty in delivering consistent microstructures and properties hinders the use of DED fabricated components in safety or performance critical applications. Variability stems from the complex thermal cycles generated by the toolpath used to print the required geometry. Several practical methods have become established in DED to regulate overheating, such as active cooling of the baseplate structure or the use of an infrared camera to inject interlayer pauses to ensure the top layer of the component cools to a set temperature, which have been shown to affect microstructure. However, no critical assessment has been performed as to how effective these controls are in promoting microstructural uniformity in the context of complex layer timing commonly generated by non-prismatic geometries. Here we show how controls influence the thermal field, phase transformations, and dynamic annealing of a low-temperature transformation steel using infrared imaging and operando neutron diffraction. Counterintuitively, common thermal homogenization process controls can reduce microstructural uniformity because these approaches stabilize peak temperature while overlooking temperatures near the solid-state phase transformation fronts. Instead, the cyclic reheating induces spatially-variant dynamically annealed regions which can be modulated via control parameters. We show that these controls have spatially linked effects centimeters away from the active weld, which implies that microstructure control must co-optimize thermal input across many subsequent layers. In conclusion, our results demonstrate the pressing need for higher order controls that integrate predictive elements of simulation data to stabilize printed properties for future qualification of DED components.

Directed energy deposition↗

Laser additive manufacturing for infrastructure repair: A case study of a deteriorated steel bridge beam

As our transportation infrastructure ages, its deterioration is becoming a growing concern. Rapid and effective methods for repair can reduce the need for time-and cost-intensive replacement of structures such as roadway bridges. In this work, laser-based additive manufacturing (AM) was developed for the re-pair of damaged beams in steel bridges. A corroded structural beam of low-carbon A36 steel was selected for this case study and 316L stainless steel was used for repair due to its excellent mechanical properties and corrosion resistance. Simulated repair experiments were performed on specimens extracted from the beam, and prepared with various groove shapes (Rectangular, Trapezoidal, and U-shaped). More in-depth parametric and microstructural studies were carried out with a series of U-shaped specimens repaired with the linear laser input energy varied from 19.5 to 30.0 J mm -1 . The tensile properties of the repaired specimens and interface structures were also investigated in detail. It was found that the repaired specimens had a slightly higher tensile strength despite a reduction in tensile elongation compared to the A36 steel base metal. The influence of interfacial microstructure and heterogeneity on the mechanical proper-ties of the repaired specimens was discussed. Furthermore, our work suggests the promising potential to employ AM for structural repair and provides fundamental insights into processing-structure-property relationships in laser AM-repaired materials.

36 MATERIALS SCIENCE↗