Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

Dynamics of Surface Alloys: Rearrangement of Pd/Ag(111) Induced by CO and O 2

To begin, alloys of Ag and small amounts of Pd are promising as bifunctional catalysts, potentially combining the inherent selectivity of the noble Ag with that of the more reactive Pd. Stable PdAg surface alloys are prepared via evaporation of Pd onto Ag(111) at room temperature followed by annealing at 400 K to create a model system. Using this procedure, the most stable form of the surface alloy under vacuum was determined to be a Ag-capped PdAg surface alloy, on the basis of a combination of X-ray photoelectron spectroscopy (XPS), scanning tunneling microscopy (STM), and density functional theory (DFT). Extensive roughening of the surface was apparent in STM images, characterized by islands of the Ag/PdAg/Ag(111) alloy of several layers thickness. The roughening is attributed to transport of Ag from the Ag(111) surface into the alloy islands. Within these islands, there is a driving force for Pd to be dispersed, surrounded by Ag, on the basis of DFT modeling. Exposure of these Ag/PdAg/Ag(111) islands to CO (0.5 Torr) at 300 K induces migration of Pd to the surface, driven by the energetic stabilization of the Pd–CO bond based on ambient-pressure XPS. Once the Pd is drawn to the surface by higher pressures of CO at room temperature, it remains stable even under very low CO partial pressures at temperatures of 300 K and below, on the basis of DFT-modeled phase behavior. Exposure to 1 Torr of O 2 at 400 K also causes Pd to resurface, and the resulting structure persists even at low pressures and temperatures below 300 K. These results establish that the state of the PdAg catalyst surface depends strongly on pretreatment and operational conditions. Hence, exposure of an alloy catalyst to CO or O 2 at moderate temperatures and pressures can lead to catalyst activation by bringing Pd to the surface. Furthermore, these results demonstrate that exposure to CO at room temperature, which is often used as a proxy for evaluating the Pd coordination sites available in a catalyst, changes the surface structure. Therefore, the CO vibrational frequencies measured with diffuse-reflectance infrared Fourier-transform spectroscopy (DRIFTS) on PdAg catalyst materials do not necessarily provide information about their working state, and fundamental understanding of the CO-PdAg alloy is crucial.

36 MATERIALS SCIENCE↗

Wildland–urban interface wildfire increases metal contributions to stormwater runoff in Paradise, California

The 2018 Camp Fire was a large late-year (November) wildfire that produced an urban firestorm in the Town of Paradise, California, USA, and destroyed more than 18 000 structures. Runoff from burned wildland areas is known to contain ash, which can transport contaminants including metals into nearby watersheds. However, due to historically infrequent occurrences, the effect of wildland-urban interface (WUI) fires, such as the Camp Fire, on surface water quality has not been well-characterized. Therefore, this study investigated the effects of widespread urban burning on surface water quality in major watersheds of the Camp Fire area. Between November 2018 and May 2019, 140 surface water samples were collected, including baseflow and stormflow, from burned and unburned watersheds with varying extent of urban development. Samples were analyzed for total and filter-passing metals, dissolved organic carbon, major anions, and total suspended solids. Ash and debris from the Camp Fire contributed metals to downstream watersheds via runoff throughout the storm season. Increases in concentration up to 200-fold were found for metals Cr, Cu, Ni, Pb, and Zn in burned watersheds compared to pre-fire values. Total concentrations of Al, Cd, Cu, Pb, and Zn exceeded EPA aquatic habitat acute criteria by up to 16-fold for up to five months after the fire. To assess possible transport mechanisms and bioavailability, a subset of 18 samples was analyzed using four filters with nominal pore sizes ranging from 0.22 to 1.2 μm to determine the particulate size distribution of metals. Trace and major metals (Al, Ba, Co, Cr, Cu, Fe, Hg, Mn, Ni, Pb, and Zn) were found mostly associated with larger grain sizes (>0.45 μm), and some metals (Al, Cr, Fe, and Pb) also included a substantial colloidal phase (0.22 to 0.45 μm). This study suggests that fires in the wildland–urban interface increase metal concentrations, mainly through particulate driven transport. The metals with the largest increases are likely from anthropogenic disaster materials, though biomass ash also is a major contributor to water quality. In conclusion, the increase in metals following WUI burning may have adverse ecological impacts.

54 ENVIRONMENTAL SCIENCES↗

Characterization of a low-pressure chlorine plasma column sustained by propagating surface waves using phase-sensitive microwave interferometry and trace-rare-gas optical emission spectroscopy

Phase-sensitive microwave interferometry and trace-rare-gas optical emission spectroscopy were used to measure the line-integrated electron density, n{sub e}, and electron temperature, T{sub e}, in a high-density chlorine plasma sustained in a quartz discharge tube (inner diameter = 6 mm) by an electromagnetic surface wave at 2.45 GHz. For pressures in the 0.1-1 Torr range, n{sub e} decreased nearly linearly along the tube's z-axis down to the critical density for surface wave propagation, where the plasma decayed abruptly. At lower pressures (< 50 mTorr), however, the plasma extended well beyond this critical point, after which n{sub e} decreased quasiexponentially toward the end of the plasma column. The length of this expansion region increased with decreasing pressure, going from {approx}8 cm at 5 mTorr to {approx}1 cm at 50 mTorr. T{sub e} was nearly independent of the axial position in the main plasma region and strongly decreased in the expansion region at lower pressures. The Cl{sub 2} percent dissociation, {tau}{sub D}, obtained from the calibrated Cl{sub 2} (306 nm)-to-Xe (828 nm) emission ratio, displayed behavior similar to that of n{sub e} and T{sub e}. For example, at 5 mTorr, {tau}{sub D} was close to 100% near the wave launcher and {approx}70% at 0.5 cm from the end of the plasma column.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Epitaxy and stress of MgO/GaAs(001) heterostructures

We report on the preparation of epitaxial MgO film on GaAs(001) substrates by molecular beam epitaxy at growth temperature of 20–200 °C. Reflection high energy electron diffraction, x-ray diffraction, and high resolution transmission electron microscopy reveal the growth of ordered crystalline cubic MgO(001) film at ∼200 °C with MgO(001)[100]|| GaAs(001)[100] and a 4 : 3 lattice registry. The surface of the MgO films, characterized by atomic force microscopy, exhibits a root mean square roughness of only 0.5 nm. In situ stress measurements reveal tensile stress as low as 1.7 GPa for a growth temperature of 200 °C in good agreement with the calculated residual misfit strain.

36 MATERIALS SCIENCE↗

A cryogenically cooled 200 kV DC photoemission electron gun for ultralow emittance photocathodes

Novel photocathode materials like ordered surfaces of single crystal metals, epitaxially grown high quantum efficiency thin films, and topologically non-trivial materials with dirac cones show great promise for generating brighter electron beams for various accelerator and ultrafast electron scattering applications. Despite several materials being identified as brighter photocathodes, none of them have been tested in electron guns to extract electron beams due to technical and logistical challenges. In this paper, we present the design and commissioning of a cryocooled 200 kV DC electron gun that is capable of testing a wide variety of novel photocathode materials over a broad range of temperatures from 298 to 35 K for bright electron beam generation. This gun is designed to enable easy transfer of the photocathode to various standard ultra-high-vacuum surface diagnostics and preparation techniques, allowing a full characterization of the dependence of beam brightness on the photocathode material and surface properties. We demonstrate the development of such a high-voltage, high-gradient gun using materials and equipment that are easily available in any standard university lab, making the development of such 200 kV electron guns more accessible.

Instruments & Instrumentation↗

In-situ spectroscopic ellipsometry for real-time characterization of the effects of high-flux helium plasmas on tungsten surfaces

Tungsten samples were exposed to He plasmas generated by an RF source (Γ i = 3.5 x 10 16 He cm -2 s -1 , ion energy = 92 eV.) The range of exposure conditions selected here is conducive to the growth of nearsurface He bubbles, and at higher fluence, the formation of W nanotendrils ranging between 50 — 100 nm in diameter. The evolution of these surface features was probed using a fixed-angle ellipsometer (280 — 1000 nm wavelength range) with direct line-of-sight to the sample. Over the parameter space explored here, changes in the two angles (p, S) that define the polarization of the reflected light followed a distinct trajectory with increasing plasma fluence. Ex-situ ellipsometry of 22 additional tungsten specimens tested at a wide range of plasma fluences and temperatures mapped onto these in-situ results well. We used helium ion microscopy and focused ion beam profiling to provide a direct calibration of the ellipsometry measurements. Our results indicate that for a reproducible process such as the growth helium-induced surface morphologies, ellipsometry is a practical in-situ diagnostic to study how fusion plasmas modify materials. To study more general effects of plasmas on surfaces, including co-deposition and sputtering, different approaches to modelling the optical properties of the exposed surfaces are also considered.

36 MATERIALS SCIENCE↗

Integrated Reflection Seismic Monitoring and Reservoir Modeling for Geologic CO 2 Sequestration

The US DOE/NETL CCS MVA program funded a project with Fusion Petroleum Technologies Inc. (now SIGMA) to model the proof of concept of using sparse seismic data in the monitoring of CO 2 injected into saline aquifers. The goal of the project was to develop and demonstrate an active source reflection seismic imaging strategy based on deployment of spatially sparse surface seismic arrays. The primary objective was to test the feasibility of sparse seismic array systems to monitor the CO 2 plume migration injected into deep saline aquifers. The USDOE/RMOTC Teapot Dome (Wyoming) 3D seismic and reservoir data targeting the Crow Mountain formation was used as a realistic proxy to evaluate the feasibility of the proposed methodology. Though the RMOTC field has been well studied, the Crow Mountain as a saline aquifer has not been studied previously as a CO 2 sequestration (storage) candidate reservoir. A full reprocessing of the seismic data from field tapes that included prestack time migration (PSTM) followed by prestack depth migration (PSDM) was performed. A baseline reservoir model was generated from the new imaging results that characterized the faults and horizon surfaces of the Crow Mountain reservoir. The 3D interpretation was integrated with the petrophysical data from available wells and incorporated into a geocellular model. The reservoir structure used in the geocellular model was developed using advanced inversion technologies including Fusion's ThinMAN™ broadband spectral inversion. Seal failure risk was assessed using Fusion's proprietary GEOPRESS™ pore pressure and fracture pressure prediction technology. CO 2 injection was simulated into the Crow Mountain with a commercial reservoir simulator. Approximately 1.2MM tons of CO 2 was simulated to be injected into the Crow Mountain reservoir over 30 years and subsequently let 'soak' in the reservoir for 970 years. The relatively small plume developed from this injection was observed migrating due to gravity to the apexes of the double anticline in the Crow Mountain reservoir of the Teapot dome. Four models were generated from the reservoir simulation task of the project which included three saturation models representing snapshots at different times during and after simulated CO 2 injection and a fully saturated CO 2 fluid substitution model. The saturation models were used along with a Gassmann fluid substitution model for CO 2 to perform fluid volumetric substitution in the Crow Mountain formation. The fluid substitution resulted in a velocity and density model for the 3D volume at each saturation condition that was used to generate a synthetic seismic survey. FPTI's (Fusion Petroleum Technologies Inc.) proprietary SeisModelPRO™ full acoustic wave equation software was used to simulate acquisition of a 3D seismic survey on the four models over a subset of the field area. The simulated acquisition area included the injection wells and the majority of the simulated plume area.

02 PETROLEUM↗

Model-Based Characterization of Elevated Temperature and High Pressure Oxy-Coal Combustion Systems

Reaction Engineering International is leading a DOE-funded program focused on characterization of the impacts of high temperatures and pressures in oxy-coal combustion systems. A primary objective is to evaluate flame behavior, heat transfer, and ash chemistry at high pressure to facilitate the application of pressurized oxy-coal in full-scale systems. The University of Utah’s 300 kW pressurized entrained flow gasifier has been successfully modified and operated as a high pressure, slurry-fed, oxy-coal combustor at firing rates ranging from nearly 100 kW to over 180 kW with reactor pressures as high as 200 psi. This presentation will describe the modifications to the gasifier to allow it to operate as a high pressure, oxy-coal combustor; detail experimental data including measurements of radiant flux, wall surface temperatures, and ash aerosol characterization; and CFD modeling of the experimental conditions. In addition, an update will be provided for accomplishments achieved to date for the component of the program focused on modeling of high temperature oxy-coal combustion using undiluted directed oxygen with minimal flue gas recirculation at atmospheric pressure.

CFD modeling↗

Design and development of liquid filled polymeric fibers with flexure rate viscoelastic properties

The design and development of a novel category of bi-component polymeric fibers, made of a polymeric sheath and a liquid core is described. To understand and to analyze the flow of molten polymer and liquid within a spin pack, we built a macroscale analogon where co-flow of polymer and liquid is investigated systematically. The macroscale analogon is composed of a glass cylinder with a finite length and a coaxial capillary. The inner fluid flows in the capillary and at its outlet meets the outer fluid flowing inside the glass cylinder. The fluids are pumped into the setup using pressurized bottles with controlled flow rates. A high-speed camera is placed in front of the glass cylinder to record the transient and the steady flow of the two phases and the morphology of their interface during co-flow. We systematically analyzed the combination of various fluids and different injection channel geometries, and used these findings to design a customized spin pack. Extrusion trials with molten polymers and specific liquids resulted in the production of liquid filled polymeric fibers (LFF) with different amounts of liquid from 3% to 33%vol. and diameters from 150μm to 1mm. Fiber morphology has been investigated with the help of optical microscopy and computer tomography, in order to analyze both surface and core morphology. Mechanical characterization of fibers has been carried out with special care to the damping capacity of such fibers using two different methods: two point bending tests to evaluate the energy dissipation of fibers upon bending at low frequency values (0.005-0.5Hz), and analysis of vibration reduction to determine the quality factor at the resonance frequency of the 1{sup st} and 3{sup rd} vibration mode.

36 MATERIALS SCIENCE↗

Exploring the Tl 2H 2 potential energy surface: A comparative analysis with group 13 systems and experiment

Abstract Thallium chemistry is experiencing unprecedented importance. Therefore, it is valuable to characterize some of the simplest thallium compounds. Stationary points along the singlet and triplet TlH potential energy surface have been characterized. Stationary point geometries were optimized with the CCSD(T)/aug‐cc‐pwCVQZ‐PP method. Harmonic vibrational frequencies were computed at the same level of theory while anharmonic vibrational frequencies were computed at the CCSD(T)/aug‐cc‐pwCVTZ‐PP level of theory. Final energetics were obtained with the CCSDT(Q) method. Basis sets up to augmented quintuple‐zeta cardinality (aug‐cc‐pwCV5Z‐PP) were employed to obtain energetics in order to extrapolate to the complete basis set limits using the focal point approach. Zero‐point vibrational energy corrections were appended to the extrapolated energies in order to determine relative energies at 0 K. It was found that the planar dibridged isomer lies lowest in energy while the linear structure lies highest in energy. The results were compared to other group 13 MH (M = B, Al, Ga, In, and Tl) theoretical studies and some interesting variations are found. With respect to experiment, incompatibilities exist.

Chemistry↗

Nanoalloy catalysts inside fuel cells: An atomic-level perspective on the functionality by combined in operando x-ray spectroscopy and total scattering

We introduce an experimental approach for structural characterization of catalysts for fuel cells combining synchrotron x-ray spectroscopy and total scattering. The approach allows probing catalysts inside operating fuel cells with atomic-level precision (~ 0.02 Å) and element specificity (~ 2–3 at%) in both time (~ 1 min) and space (~ μm) resolved manner. The approach is demonstrated on exemplary Pd-Sn and Pt-Ni-Cu nanoalloy catalysts for the oxygen reduction reaction (ORR) deposited on the cathode of an operating proton exchange membrane fuel cell. In operando x-ray data show that under operating conditions, the catalyst particles can undergo specific structural changes, ranging from sub-Å atomic fluctuations and sharp nanophase transitions to a gradual strain relaxation and growth, which inflict significant losses in their ORR activity. Though triggered electrochemically, the changes are not driven solely by differences in the reduction potential and surface energy of the metallic species constituting the nanoalloys but also by the formation energy of competing nanophases, mismatch between the size of individual atomic species and their ability to interdiffuse fast in search of energetically favorable configurations. Given their complexity, the changes are difficult to predict and so the resulting ORR losses remain difficult to limit. We show that in operando knowledge of the structural evolution of nanoalloy catalysts helps create strategies for improving their activity and stability. In particular, we show that shaping Pd-Sn nanoalloys rich in Pd as cubes reduces the interdiffusion of atoms at their surface and so makes them better catalysts for ORR in fuel cells in comparison to other Pd-Sn nanoalloys. In addition, we demonstrate that the approach introduced here can provide knowledge of other major factors affecting the performance of fuel cells such as operating temperature and the overall catalyst utilization, in particular the evolution of elemental and mass distribution of catalyst particles over the cells’ cathode. Last but not least, we discuss how in operando x-ray spectroscopy and total x-ray scattering can bridge the knowledge gap between the widely used in situ SAXS, EXAFS and monocrystal surface XRD techniques for structural characterization of nanoalloy catalysts explored for energy related applications.

25 ENERGY STORAGE↗

Improved Prediction of Cold-Air Pools in the Weather Research and Forecasting Model Using a Truly Horizontal Diffusion Scheme for Potential Temperature

The terrain-following vertical coordinate system used by many atmospheric models, including the Weather Research and Forecasting (WRF) Model, is prone to errors in regions of complex terrain. These errors stem, in part, from the calculation of horizontal gradients within the diffusion term of the momentum or scalar evolution equations. In WRF, such gradients can be calculated along coordinate surfaces, or using metric terms that help account for grid skewness. However, neither of these options ensures a truly horizontal gradient calculation, especially if a grid cell is skewed enough that the heights of the neighboring grid points used in the calculation fall outside the vertical range of the cell. In this work, an improved scheme that uses Taylor series approximations to vertically interpolate variables to the level necessary for a truly horizontal gradient calculation is implemented in WRF for the diffusion of potential temperature. The scheme is validated using an atmosphere-at-rest configuration, in which spurious flows develop only as a result of numerical errors and can thus be used as a proxy for model performance. Following validation, the method is applied to the simulation of cold-air pools (CAPs), which occur in regions of complex terrain and are characterized by strong near-surface temperature gradients. Using the truly horizontal scheme, idealized simulations demonstrate reduced numerical mixing in a quiescent CAP, and a realistic case study in the Columbia River basin shows a reduction in positive wind speed bias by up to roughly 20% compared to observations from the Second Wind Forecast Improvement Project.

54 ENVIRONMENTAL SCIENCES↗

Local conformations and heterogeneities in structures and dynamics of isotactic polypropylene adsorbed onto carbon fiber

Carbon fiber (CF) reinforced polymers (CFRPs) have experienced widespread use in various industries. One of the most important parameters that controls the macroscopic property of CFRPs is the interface between a polymer matrix and CF. There is growing evidence to suggest the formation of a bound polymer layer (BPL), i.e., polymer chains that physically adsorb on a filler surface. However, this interface is always in contact with the thicker part of a polymer matrix, rendering its understanding a difficult task. Therein, we use CF-reinforced isotactic polypropylene (iPP) as a rational CFRP. To characterize the BPL on the CF surface, we extracted it from the CFRP using solvent-rinsing with p-xylene. The physical and thermal properties of the BPL were characterized by differential scanning calorimetry and thermogravimetric analysis, while its microscopic structures and dynamics were probed by small-angle neutron scattering and quasi-elastic neutron scattering (QENS) techniques. Subsequently, we employed atomistic molecular dynamics (MD) simulations to complement the QENS results above the bulk melting temperature and reveal details that were experimentally inaccessible. In this work, we observed that the degree of crystallinity of the BPL was quite lower than the bulk, while the melting temperature of the BPL remained the same as the bulks. Within the given length and time scales probed by QENS and MD, we also observed that most of the bound chains were mobile, with the formation of a high-density region (less than 1 nm in thickness) near the CF surface. The segmental dynamics of the bound chains probed by both QENS and MD were also much faster than those of the free chains, possibly due to the presence of a free surface region at the topmost surface of the BPL. Furthermore, the MD results demonstrated that the backbone chains and side groups lie nearly flat on the CF surface, which is the driving force for the flattening process of the iPP BPL to overcome the conformational entropy loss in the total free energy.

36 MATERIALS SCIENCE↗

Electrochemical behavior of SnCl 2 and influence of Cu and Ni ions in molten LiCl−KCl−CaCl 2 eutectic

Reliable transport and thermodynamic data for multivalent ions in complex molten salts are scarce, limiting model fidelity for electrorefining and impurity control. Here, we report a comprehensive electrochemical characterization of SnCl₂ in LiCl–KCl–CaCl₂ (50.5–44.2–5.3 mol%) at 685 K, including the effects of Ni 2+ and Cu + impurities. Using cyclic voltammetry (CV), chronoamperometry (CA), and chronopotentiometry (CP), we quantified Sn 2+ and Ni 2+ diffusion with exceptional agreement across methods: Sn 2+ averaged (1.03 ± 0.10) × 10 −5 cm 2 s −1 , and Ni 2+ averaged (0.75 ± 0.19) × 10 −5 cm 2 s −1 . The tight confidence-interval overlap across CV, CA, and CP strengthens confidence in these values and is uncommon in molten chloride studies. Open-circuit-potential measurements provided standard apparent reduction potentials that closely match LiCl–KCl literature, indicating minimal shift with CaCl₂ present. The Sn 2+ /Sn couple behaves as a reversible two-electron soluble–insoluble process at 685 K; the Sn 4+ /Sn 2+ couple transitions to soluble–soluble behavior near 788 K, which may correlate with the decomposition of surface bound chlorostannates, though direct characterization remains to be established. In mixed systems, Cu+/Cu overlaps Sn 2+ /Sn, limiting Cusingle bondSn electroseparation, whereas the larger potential gap between Ni 2+ /Ni and Sn 2+ /Sn supports selective Ni removal. These internally consistent transport and thermodynamic data establish a validated basis for process modeling and optimization of Sn electrorefining and impurity management in LiCl–KCl–CaCl₂.

Berzins-Delahay↗

Analysis of Potential Leakage Pathways and Mineralization within Caprocks for Geologic Storage of CO 2

We used a multifaceted approach to investigate the nature of caprocks above, and the interface between, reservoir-quality rocks that might serve as targets for carbon storage. Fieldwork in southeastern Utah examined the regional- to m-scale nature of faults and fractures across the sedimentiological interfaces. We also used microscopic analyses and mechanical modeling to examine the question as to how the contacts between units interact, and how fractures may allow fluids to move from reservoirs to caprock. Regional-­scale analyses using ASTER data enabled us to identify location of alteration, which led to site-­specific studies of deformation and fluid flow. In the Jurassic Carmel Formation, a seal for the Navajo Sandstone, we evaluated mesoscale variability in fracture density and morphology and variability in elastic moduli in the Jurassic Carmel Formation, a proposed seal to the underlying Navajo Sandstone for CO 2 geosequestration. By combining mechano-stratigraphic outcrop observations with elastic moduli derived from wireline log data, we characterize the variability in fracture pattern and morphology with the observed variability in rock strength within this heterolithic top seal. Outcrop inventories of discontinuities show fracture densities decrease as bed thickness increases and fracture propagation morphology across lithologic interfaces vary with changing interface type. Dynamic elastic moduli, calculated from wireline log data, show that Young’s modulus varies by up to 40 GPa across depositional interfaces, and by an average of 3 GPa across the reservoir/seal interface. We expect that the mesoscale changes in rock strength will affect the distributions of localized stress and thereby influence fracture propagation and fluid flow behavior within the seal. These data provide a means to closely tie outcrop observations to those derived from subsurface data and estimates of subsurface rock strength. We also studied damage zones associated normal faults in the Permian Cedar Mesa Sandstone, southeastern Utah. These faults are characterized by a single slip surfaces and damage zones containing deformation bands, veins, and joints. Field observations include crosscutting relationships, permeability increase, rock strength decrease, and ultraviolet light induced mineral fluorescence within the damage zone. These field observations combined with the interpreted paragenetic sequence from petrographic analysis, suggests a deformation history of reactivation and several mineralization events in an otherwise low-permeability fault. All deformation bands and veins fluoresce under ultraviolet light, suggesting connectivity and a shared mineralization history. Pre-­existing deformation features act as loci for younger deformation and mineralization events, this fault and its damage zone illustrate the importance of the fault damage zone to subsurface fluid flow. We model a simplified stress history in order to understand the importance of rock properties and magnitude of tectonic stress on the deformation features within the damage zone. The moderate confining pressures, possible variations in pore pressure, and the porous, fine-­grained nature of the Cedar Mesa Sandstone results in a fault damage zone characterized by enhanced permeability, subsurface fluid flow, and mineralization. Structural setting greatly influences fracture spacing and orientation. Three structural settings were examined and include fault proximity, a fold limb of constant dip, and a setting proximal to the syncline hinge. Fracture spacing and dominant fracture orientation vary at each setting and distinctions between regional and local paleo-stress directions can be made. Joints on the fold limb strike normal to the fold axis/bedding and are interpreted to be sub-parallel to the maximum regional paleo-stress direction as there is no fold related strain. Joints proximal to faults and the syncline hinge may have formed under local stress conditions associated with folding and faulting, and in some cases, are perpendicular to the maximum regional paleo-stress direction. Macroscale analyses of the Iron Wash fault, which cuts most of the stratigraphy of the reservoir- seal analogs, reveals that seal bypass occurs along faults with mixed lithologic composition. While portions of the fault may be effective seals, when modeled as a whole the fault zone cannot support a high CO 2 column. We adapted oil-field methods to calculate column heights and sealing capacities. Examination of the burial and tectonic histories of the rocks, coupled with field- and micro-­scale studies, allow us to examine the potential for seal failure using basic rock mechanics failure analyses. These studies reveal that the sealing lithologies experienced multiple episodes of deformation that resulted in numerous fractures and small faults. In a stress state based on burial history and overburden loads, we show that most of the seals could fail with normal to slightly excess pore pressures.

58 GEOSCIENCES↗

Pd-CeO 2 catalyst facilely derived from one-pot generated Pd@Ce-BTC for low temperature CO oxidation

Due to the capacity to offer abundant catalytic sites within porous solids featuring high surface areas, metal-organic frameworks (MOFs) and their derivatives have garnered considerable attention as prospective catalysts in environmental catalysis. Here, to promote the industrial application of MOFs, there is an urgent need for an effective and environmental-friendly preparation approach. Breaking through the limitation of the traditional two-step preparation method that Pd was introduced to the already prepared Ce-BTC (Pd/Ce-BTC, BTC = 1, 3, 5 benzenetricarboxylate), in this work, we present a novel one-pot solvothermal method for synthesizing the Pd material supported by Ce-BTC (Pd@Ce-BTC). After pyrolysis in N 2 flow or air flow, Pd-CeO 2 catalysts derived from Pd@Ce-BTC exhibited much higher CO oxidation activity than those from Pd/Ce-BTC. Moreover, Pd/Ce-BTC and Pd@Ce-BTC pyrolyzed in N 2 flow (Pd/Ce-BTC-N and Pd@Ce-BTC-N) could better catalyze the oxidation of CO than Pd/Ce-BTC and Pd@Ce-BTC pyrolyzed in air flow (Pd/Ce-BTC-A and Pd@Ce-BTC-A). Further characterizations revealed that the abundant surface Ce 3+ species, rich surface adsorbed oxygen species and superior redox properties were the main reasons for the superior CO oxidation activity of Pd@Ce-BTC-N.

36 MATERIALS SCIENCE↗