Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

PNNL Stress/Strain Correlation for Zircaloy

Pacific Northwest National Laboratory (PNNL) was tasked with incorporating cladding mechanical property data into the Nuclear Regulatory Commission (NRC) fuel codes, FRAPCON-31 and FRAPTRAN2, by the NRC Office of Nuclear Reactor Research. The objective of that task was to create a mechanical model that can calculate true stress, true strain, and the possible failure of the fuel rod cladding based on uniaxial test data.

36 MATERIALS SCIENCE↗

Solid-State Welding of the Nanostructured Ferritic Alloy 14YWT Using a Capacitive Discharge Resistance Welding Technique

Joining nanostructured ferritic alloys (NFAs) has proved challenging, as the nano-oxides that provide superior strength, creep resistance, and radiation tolerance at high temperatures tend to agglomerate, redistribute, and coarsen during conventional fusion welding. In this study, capacitive discharge resistance welding (CDRW)—a solid-state variant of resistance welding—was used to join end caps and thin-walled cladding tubes of the NFA 14YWT. The resulting solid-state joints were found to be hermetically sealed and were characterized across the weld region using electron microscopy (macroscopic, microscopic, and nanometer scales) and nanoindentation. Microstructural evolution near the weld line was limited to narrow (~50–200 μm) thermo-mechanically affected zones (TMAZs) and to a reduction in pre-existing component textures. Dispersoid populations (i.e., nano-oxides and larger oxide particles) appeared unchanged by all but the highest energy and power CDRW condition, with this extreme producing only minor nano-oxide coarsening (~2 nm → ~5 nm Ø). Despite a minimal microstructural change, the TMAZs were found to be ~10% softer than the surrounding base material. These findings are considered in terms of past solid-state welding (SSW) efforts—cladding applications and NFA-like materials in particular—and in terms of strengthening mechanisms in NFAs and the potential impacts of localized temperature–strain conditions during SSW.

36 MATERIALS SCIENCE↗

Assessment of PCMI Simulation Using the Multidimensional Multiphysics BISON Fuel Performance Code

Since 2008, the Idaho National Laboratory (INL) has been developing a next-generation nuclear fuel performance code called BISON. BISON is built using INL’s Multiphysics Object-Oriented Simulation Environment, or MOOSE. MOOSE is a massively parallel, finite element-based framework to solve systems of coupled non-linear partial differential equations using the Jacobian-FreeNewton Krylov (JFNK) method. MOOSE supports the use of complex two- and three-dimensional meshes and uses implicit time integration, which is important for the widely varied time scales in nuclear fuel simulation. MOOSE’s object-oriented architecture minimizes the programming required to add new physics models. BISON has been applied to various nuclear fuel problems to assess the accuracy of its 2D and 3D capabilities. The benchmark results used in this assessment range from simulation results from other fuel performance codes to measurements from well-known and documented reactor experiments. An example of a well-documented experiment used in this assessment is the Third Risø Fission Gas Project, referred to as “Bump Test GE7”, which was performed on rod ZX115. This experiment was chosen because it allows for an evaluation of several aspects of the code, including fully coupled thermo-mechanics, contact, and several nonlinear material models. Bump Test GE7 consists of a base-irradiation period of a full-length rod in the Quad-Cities-1 BWR for nearly 7 years to a burnup of 4.17% FIMA. The base irradiation test is followed by a “bump test” of a sub-section of the original rod. The bump test takes place in the test reactor DR3 at Risø in a water-cooled HP1 rig under BWR conditions where the power level is increased by about 50% over base irradiation levels in the span of several hours. During base irradiation, the axial power profile is flat. During the bump test, the axial power profile changes so that the bottom half of the rod is at approximately 50% higher power than at the base irradiation level, while the power at the top of the rod is at about 20% of the base irradiation power level. 2D BISON simulations of the Bump Test GE7 were run using both discrete and smeared pellet geometry. Comparisons between these calculations and experimental measurements are presented for clad diameter and elongation after the base irradiation and clad profile along the length of the test section after the bump test. Preliminary comparisons between calculations and measurements are favorable, supporting the use of BISON as an accurate multiphysics fuel simulation tool.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

A Novel Zr-1Nb Alloy and a New Look at Hydriding

A novel Zr-1Nb has begun development based on a working model that takes into account the hydrogen permeabilities for zirconium and niobium metals. The beta-Nb secondary phase particles (SPPs) in Zr-1Nb are believed to promote more rapid hydrogen dynamics in the alloy in comparison to other zirconium alloys. Furthermore, some hydrogen release is expected at the lower temperatures corresponding to outages when the partial pressure of H2 in the coolant is less. These characteristics lessen the negative synergism between corrosion and hydriding that is otherwise observed in cladding alloys without niobium. In accord with the working model, development of nanoscale precursors was initiated to enhance the performance of existing Zr-1Nb alloys. Their characteristics and properties can be compared to oxide-dispersion strengthened alloys, and material additions have been proposed to zirconium-based LWR cladding to guard further against hydriding and to fix the size of the SPPs for microstructure stability enhancements. A preparative route is being investigated that does not require mechanical alloying, and 10 nanometer molybdenum particles have been prepared which are part of the nanoscale precursors. If successful, the approach has implications for long term dry storage of used fuel and for new routes to nanoferritic and ODS alloys.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High Burn-Up Spent Nuclear Fuel Vibration Integrity Study

The Oak Ridge National Laboratory (ORNL) has developed the cyclic integrated reversible-bending fatigue tester (CIRFT) approach to successfully demonstrate the controllable fatigue fracture on high burnup (HBU) spent nuclear fuel (SNF) in a normal vibration mode. CIRFT enables examination of the underlying mechanisms of SNF system dynamic performance. Due to the inhomogeneous composite structure of the SNF system, the detailed mechanisms of the pellet-pellet and pellet-clad interactions and the stress concentration effects at the pellet-pellet interface cannot be readily obtained from a CIRFT system measurement. Therefore, finite element analyses (FEAs) are used to translate the global moment-curvature measurement into local stress-strain profiles for further investigation. The major findings of CIRFT on the HBU SNF are as follows: SNF system interface bonding plays an important role in SNF vibration performance. Fuel structure contributes to SNF system stiffness. There are significant variations in stress and curvature of SNF systems during vibration cycles resulting from segment pellets and clad interactions. SNF failure initiates at the pellet-pellet interface region and appears to be spontaneous.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Transient Reactor Test Facility (TREAT) Low Enriched Uranium (LEU) Conversion Progress

The National Nuclear Security Administration Office of Material Management and Minimization (NNSA M3) is working towards converting the Transient Reactor Test Facility (TREAT) located at the Idaho National Laboratory (INL) from its original high-enriched uranium (HEU) core to a low-enriched uranium (LEU) core. TREAT reactor operations were restarted in November of 2017 and data obtained from the initial testing will be used to validate the existing ANL reactor modeling. Fuel block development has progressed with the completion of 2 and 4 inch crack free surrogate fuel blocks. Alternative fabrication methods for the fuel blocks continue to be explored and are showing promising results. Additionally, cladding oxidation studies have been performed and analyzed to initiate the down selection of cladding material to be used for the TREAT LEU fuel elements. This paper describes the current status of the above mentioned activities, and discusses the anticipated path forward for the conversion program as it progresses toward a final fuel design and fuel fabrication process.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Milestone 1.2.9: Radiolytic Gas Generation Measurements from Helium Backfilled Samples of AA1100 and AA6061 Coupons

Nearly 18 metric tons of aluminum-clad spent nuclear fuel (ASNF) is safely managed by the U.S. Department of Energy (DOE). These assemblies are currently in interim storage, with the intention of extended storage (>50 years) until final disposal. Strategies for the continued safe storage of this material are under evaluation, of which a key criterion is the extent of molecular hydrogen gas (H2) formation from the radiolysis of hydrated (oxy)hydroxide aluminum corrosion layers arising from in-reactor and wet storage conditions. Radiation-induced H2 formation has the potential to compromise cladding and storage canister integrity, in addition to promoting the formation of unfavorable gaseous environments. Consequently, understanding this radiation-induced phenomenon is essential for the development of predictive modeling capabilities to support technical considerations and the identification of radiation related challenges for the extended storage of ASNF. Here, we report radiolytic H2 yields (G-values, G(H2)) from the gamma irradiation of ‘pristine’ and pre-corroded aluminum coupons in helium (He) environments as a function of alloy composition (AA1100 and AA6061), relative humidity, and absorbed gamma dose. Measured yields were lower than corresponding values reported for argon environments, a positive result for proposed extended dry storage strategies that would employ helium as a backfill gas. Interestingly, the presented G(H2)He values are comparable to those previously measured in nitrogen environments, suggesting a He mediated H2 inhibition process, attributed here to Penning ionization.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Core design study of a supercritical light water reactor with double row fuel rods

An equilibrium core for supercritical light water reactor has been designed. A novel type of fuel assembly with dual rows of fuel rods between water rods is chosen and optimized to get more uniform assembly power distributions. Stainless steel is used for fuel rod cladding and structural material. Honeycomb structure filled with thermal isolation is introduced to reduce the usage of stainless steel and to keep moderator temperature below the pseudo critical temperature. Water flow scheme with ascending coolant flow in inner regions is carried out to achieve high outlet temperature. In order to enhance coolant outlet temperature, the radial power distributions needs to be as flat as possible through operation cycle. Fuel loading pattern and control rod pattern are optimized to flatten power distribution at inner regions. Axial fuel enrichment is divided into three parts to control axial power peak, which affects maximum cladding surface temperature. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Neutron damage reduction in a traveling wave reactor

Traveling wave reactors are envisioned to run on depleted or natural uranium with no need for enrichment or reprocessing, and in a manner which requires little to no operator intervention. If feasible, this type of reactor has significant advantages over conventional nuclear power systems. However, a practical implementation of this concept is challenging as neutron irradiation levels many times greater than those in conventional reactors appear to be required for a fission wave to propagate. Radiation damage to the fuel and cladding materials presents a significant obstacle to a practical design. One possibility for reducing damage is to soften the neutron energy spectrum. Here we show that using a uranium oxide fuel form will allow a shift in the neutron spectrum that can result in at least a three fold decrease in dpa levels for fuel cladding and structural steels within the reactor compared with the dpa levels expected when using a uranium metal fuel. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

A 100 MWe advanced sodium-cooled fast reactor core concept

An Advanced sodium-cooled Fast Reactor core concept (AFR-100) was developed targeting a small electrical grid to be transportable to the plant site and operable for a long time without frequent refueling. The reactor power rating was strategically decided to be 100 MWe, and the core barrel diameter was limited to 3.0 m for transportability. The design parameters were determined by relaxing the peak fast fluence limit and bulk coolant outlet temperature to beyond irradiation experience assuming that advanced cladding and structural materials developed under US-DOE programs would be available when the AFR-100 is deployed. With a de-rated power density and U-Zr binary metallic fuel, the AFR-100 can maintain criticality for 30 years without refueling. The average discharge burnup of 101 MWd/kg is comparable to conventional design values, but the peak discharge fast fluence of {approx}6x10{sup 23} neutrons/cm{sup 2} is beyond the current irradiation experiences with HT-9 cladding. The evaluated reactivity coefficients provide sufficient negative feedbacks and the reactivity control systems provide sufficient shutdown margins. The integral reactivity parameters obtained from quasi-static reactivity balance analysis indicate that the AFR-100 meets the sufficient conditions for acceptable asymptotic core outlet temperature following postulated unprotected accidents. Additionally, the AFR-100 has sufficient thermal margins by grouping the fuel assemblies into eight orifice zones. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Simulation of 1% hot leg SBLOCA with TRACE5

During a Small Break Loss-of-Coolant Accident (SBLOCA) transient, depressurization can be slow enough to delay the Accumulators (ACC) entry for a long time. Actuation of High Pressure Injection (HPI) system is then necessary in order to maintain the core temperature low enough to avoid core boil off, and consequently avoiding the core level to fall below fuel rods level, thus producing a temperature trip in the fuel cladding. In this frame, the OECD/NEA ROSA Project Test 1.2 (SB-HL-17 in Japan Atomic Energy Agency (JAEA)) has been simulated using the thermal-hydraulic code TRACES. Test 1.2 was performed in the Large Scale Test Facility (LSTF) reproducing a 1% hot leg SBLOCA in a Pressurized Water Reactor (PWR). A comparison between experimental and the main simulated variables was performed to study the effect of important parameters (liquid stratification, geometry and size) to model the break. Finally, in an Emergency Core Cooling System (ECCS) failure scenario, loss of coolant is large enough to produce core boil-off and a Peak Cladding Temperature (PCT) excursion. With this purpose a sensitivity analysis varying the HPI mass flow rate has been performed covering the range between HPI actuation and failure. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Multi-scale approach to the modeling of fission gas discharge during hypothetical loss-of-flow accident in gen-IV sodium fast reactor

The required technological and safety standards for future Gen IV Reactors can only be achieved if advanced simulation capabilities become available, which combine high performance computing with the necessary level of modeling detail and high accuracy of predictions. The purpose of this paper is to present new results of multi-scale three-dimensional (3D) simulations of the inter-related phenomena, which occur as a result of fuel element heat-up and cladding failure, including the injection of a jet of gaseous fission products into a partially blocked Sodium Fast Reactor (SFR) coolant channel, and gas/molten sodium transport along the coolant channels. The computational approach to the analysis of the overall accident scenario is based on using two different inter-communicating computational multiphase fluid dynamics (CMFD) codes: a CFD code, PHASTA, and a RANS code, NPHASE-CMFD. Using the geometry and time history of cladding failure and the gas injection rate, direct numerical simulations (DNS), combined with the Level Set method, of two-phase turbulent flow have been performed by the PHASTA code. The model allows one to track the evolution of gas/liquid interfaces at a centimeter scale. The simulated phenomena include the formation and breakup of the jet of fission products injected into the liquid sodium coolant. The PHASTA outflow has been averaged over time to obtain mean phasic velocities and volumetric concentrations, as well as the liquid turbulent kinetic energy and turbulence dissipation rate, all of which have served as the input to the core-scale simulations using the NPHASE-CMFD code. A sliding window time averaging has been used to capture mean flow parameters for transient cases. The results presented in the paper include testing and validation of the proposed models, as well the predictions of fission-gas/liquid-sodium transport along a multi-rod fuel assembly of SFR during a partial loss-of-flow accident. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Fuel elements of research reactor CM

In 1961 the CM research reactor was commissioned at the Research Institute of Atomic Reactors (Dimitrovgrad, Russia), it was intended to carry on investigations and the production of transuranium nuclides. The reactor is of a tank type. Original fuel assembly contained plate fuels that were spaced with vanes and corrugated bands. Nickel was used as a cladding material, fuel meat was produced from UO{sub 2} + electrolytic nickel composition. Fuel plates have been replaced by self-spacing cross-shaped dispersion fuels clad in stainless steel. In 2005 the reactor was updated. The purpose of this updating was to increase the quantity of irradiation channels in the reactor core and to improve the neutron balance. The updating was implemented at the expense of 20 % reduction in the quantity of fuel elements in the core which released a space for extra channels and decreased the mass of structural materials in the core. The updated reactor is loaded with modified standard fuel elements with 20 % higher uranium masses. At the same time stainless steel in fuel assembly shrouds was substituted by zirconium alloy. Today in progress are investigations and work to promote the second stage of reactor updating that involve developments of cross-shaped fuel elements having low neutron absorption matrix materials. This article gives an historical account of the design and main technical changes that occurred for the CM reactor since its commissioning.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Establishment of the roadmap for chlorination process development for zirconium recovery and recycle

Process development studies are being conducted to recover, purify, and reuse the zirconium (about 98.5% by mass) in used nuclear fuel (UNF) zirconium alloy cladding. Feasibility studies began in FY 2010 using empty cladding hulls that were left after fuel dissolution or after oxidation to a finely divided oxide powder (voloxidation). In FY 2012, two industrial teams (AREVA and Shaw-Westinghouse) were contracted by the Department of Energy Office of Nuclear Energy (NE) to provide technical assistance to the project. In FY 2013, the NE Fuel Cycle Research and Development Program requested development of a technology development roadmap to guide future work. The first step in the roadmap development was to assess the starting point, that is, the current state of the technology and the end goal. Based on previous test results, future work is to be focused on first using chlorine as the chlorinating agent and secondly on the use of a process design that utilizes a chlorination reactor and dual ZrCl{sub 4} product salt condensers. The likely need for a secondary purification step was recognized. Completion of feasibility testing required an experiment on the chemical decladding flowsheet option. This was done during April 2013. The roadmap for process development will continue through process chemistry optimization studies, the chlorinated reactor design configuration, product salt condensers, and the off-gas trapping of tritium or other volatile fission products from the off-gas stream. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Influence of uranium hydride oxidation on uranium metal behaviour

This work addresses concerns that the rapid, exothermic oxidation of active uranium hydride in air could stimulate an exothermic reaction (burning) involving any adjacent uranium metal, so as to increase the potential hazard arising from a hydride reaction. The effect of the thermal reaction of active uranium hydride, especially in contact with uranium metal, does not increase in proportion with hydride mass, particularly when considering large quantities of hydride. Whether uranium metal continues to burn in the long term is a function of the uranium metal and its surroundings. The source of the initial heat input to the uranium, if sufficient to cause ignition, is not important. Sustained burning of uranium requires the rate of heat generation to be sufficient to offset the total rate of heat loss so as to maintain an elevated temperature. For dense uranium, this is very difficult to achieve in naturally occurring circumstances. Areas of the uranium surface can lose heat but not generate heat. Heat can be lost by conduction, through contact with other materials, and by convection and radiation, e.g. from areas where the uranium surface is covered with a layer of oxidised material, such as burned-out hydride or from fuel cladding. These rates of heat loss are highly significant in relation to the rate of heat generation by sustained oxidation of uranium in air. Finite volume modelling has been used to examine the behaviour of a magnesium-clad uranium metal fuel element within a bottle surrounded by other un-bottled fuel elements. In the event that the bottle is breached, suddenly, in air, it can be concluded that the bulk uranium metal oxidation reaction will not reach a self-sustaining level and the mass of uranium oxidised will likely to be small in relation to mass of uranium hydride oxidised. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Operational Challenges of Extended Dry Storage of Spent Nuclear Fuel - 12550

As a result of the termination of the Yucca Mountain used fuel repository program and a continuing climate of uncertainty in the national policy for nuclear fuel disposition, the likelihood has increased that extended storage, defined as more than 60 years, and subsequent transportation of used nuclear fuel after periods of extended storage may become necessary. Whether at the nation's 104 nuclear energy facilities, or at one or more consolidated interim storage facilities, the operational challenges of extended storage and transportation will depend upon the future US policy for Used Fuel Management and the future Regulatory Framework for EST, both of which should be developed with consideration of their operational impacts. Risk insights into the regulatory framework may conclude that dry storage and transportation operations should focus primarily on ensuring canister integrity. Assurance of cladding integrity may not be beneficial from an overall risk perspective. If assurance of canister integrity becomes more important, then mitigation techniques for potential canister degradation mechanisms will be the primary source of operational focus. If cladding integrity remains as an important focus, then operational challenges to assure it would require much more effort. Fundamental shifts in the approach to design a repository and optimize the back-end of the fuel cycle will need to occur in order to address the realities of the changes that have taken place over the last 30 years. Direct disposal of existing dual purpose storage and transportation casks will be essential to optimizing the back end of the fuel cycle. The federal used fuel management should focus on siting and designing a repository that meets this objective along with the development of CIS, and possibly recycling. An integrated approach to developing US policy and the regulatory framework must consider the potential operational challenges that they would create. Therefore, it should be integral to these efforts to redefine retrievability to apply to the dual purpose cask, and not to apply to individual assemblies. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The use of gamma spectrometry in the determination of fission products migration in irradiated fuel

Non destructive examinations realized in hot cells of LECA STAR facility give main data on irradiated fuel rods and pins. Among those examinations, gamma spectrometry allows access to fuel, inside the cladding, thanks to gamma rays of fission products such as {sup 137}Cs, {sup 154}Eu coming from pellets... From those gamma scannings we can detect the position and the length of the fuel column and of its pellets, calculate local burnup.. In the database of our lab we have already such gamma scannings on hundreds of rods or pins with different fuels, claddings and irradiations conditions (under nominal or non nominal). We have detected that in specific cases, an unusual shape of the {sup 137}Cs scanning (distribution quite different from those of {sup 154}Eu) can be explained by the migration of this isotope, moving to the cold sides of the pellet. This phenomenon is mainly associated with an increasing of the pellet's temperature. Based on our observations, we have developed a quantitative approach of the changes on the {sup 137}Cs scannings through the calculation of appropriate 'indicators'. Those calculations allow us to be able to localize, quantify and compare the {sup 137}Cs migration all along rods or pins. Those migration results are so quickly and easily achievable from gamma measurements and can then be easily correlated to other observations realized with destructive examinations, puncturing and calculations, already realized or to come. Because such a migration is the result of temperature increasing in the pellets, our indicators can be directly associated with this local temperature. In perspective, thermically activated phenomena such as geometrical changes in the shape of the pellets, fission gas release... can also indirectly be deduced from our indicators. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

BISON modeling of reactivity-initiated accident experiments in a static environment

In conjunction with the restart of the TREAT reactor and the design of test vehicles, modeling and simulation efforts are being used to model the response of Accident Tolerant Fuel (ATF) concepts under reactivity-initiated accident (RIA) conditions. The purpose of this work is to model a baseline case of a 10 cm long UO{sub 2}- Zircaloy fuel rodlet in the Multi-SERTTA capsule in PWR conditions, using BISON and RELAP5 over a range of energy depositions and with varying reactor power pulse widths. The results provide an initial best estimate of fuel performance modeling during a RIA event in TREAT with a focus on the effect of varying the pulse width and energy deposition on both thermal and mechanical parameters that are important for predicting failure of the fuel rodlet. The combined BISON/RELAP5 model captures coupled thermal and mechanical effects on the fuel-to-cladding gap conductance, cladding-to-coolant heat transfer coefficient and water temperature and pressure that would not be capable in each code individually. These combined effects allow for a more accurate modeling of the thermal and mechanical response in the fuel rodlet and thermal-hydraulics of the test vehicle. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗