SEARCH · Search NASA

Results for “Coating processes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

All sources NASA NTRS DOE OSTI

NASA NTRS1980

Silicon solar cells with high open-circuit voltage

Open-circuit voltages as high as 0.645 V (AM0-25 C) have been obtained by a new process developed for low-resistivity silicon. The method utilizes high-dose phosphorus implantation, followed by furnace annealing and simultaneous oxide growth to form high-efficiency, shallow junctions. The effect of the thermally grown oxide is a reduction of surface recombination velocity; the oxide also acts as a moderately efficient AR coating. Boron doped silicon with resistivities from 0.1 to 0.3 ohm-cm has been processed according to this sequence; results show highest open-circuit voltage is attained with 0.1-ohm-cm starting material. The effects of bandgap narrowing, caused by high doping concentrations in the junction, were also investigated by implanting phosphorus over a wide range of dose levels.

Minnucci, J. A.↗

NASA NTRS2004

Method Developed for Improving the Thermomechanical Properties of Silicon Carbide Matrix Composites

Today, a major thrust for achieving engine components with improved thermal capability is the development of fiber-reinforced silicon-carbide (SiC) matrix composites. These materials are not only lighter and capable of higher use temperatures than state-of-the-art metallic alloys and oxide matrix composites (approx. 1100 C), but they can provide significantly better static and dynamic toughness than unreinforced silicon-based monolithic ceramics. However, for successful application in advanced engine systems, the SiC matrix composites should be able to withstand component service stresses and temperatures for the desired component lifetime. Since the high-temperature structural life of ceramic materials is typically controlled by creep-induced flaw growth, a key composite property requirement is the ability to display high creep resistance under these conditions. Also, because of the possibility of severe thermal gradients in the components, the composites should provide maximum thermal conductivity to minimize the development of thermal stresses. State-of-the-art SiC matrix composites are typically fabricated via a three-step process: (1) fabrication of a component-shaped architectural preform reinforced by high-performance fibers, (2) chemical vapor infiltration of a fiber coating material such as boron nitride (BN) into the preform, and (3) infiltration of a SiC matrix into the remaining porous areas in the preform. Generally, the highest performing composites have matrices fabricated by the CVI process, which produces a SiC matrix typically more thermally stable and denser than matrices formed by other approaches. As such, the CVI SiC matrix is able to provide better environmental protection to the coated fibers, plus provide the composite with better resistance to crack propagation. Also, the denser CVI SiC matrix should provide optimal creep resistance and thermal conductivity to the composite. However, for adequate preform infiltration, the CVI SiC matrix process typically has to be conducted at temperatures below 1100 C, which results in a SiC matrix that is fairly dense, but contains metastable atomic defects and is nonstoichiometric because of a small amount of excess silicon. Because these defects typically exist at the matrix grain boundaries, they can scatter thermal phonons and degrade matrix creep resistance by enhancing grain-boundary sliding. To eliminate these defects and improve the thermomechanical properties of ceramic composites with CVI SiC matrices, researchers at the NASA Glenn Research Center developed a high-temperature treatment process that can be used after the CVI SiC matrix is deposited into the fiber preform.

Bhatt, Ramakrishna T.↗

DOE OSTI2019

Nanoparticle Size and Coating Chemistry Control Foliar Uptake Pathways, Translocation, and Leaf-to-Rhizosphere Transport in Wheat

Nano enabled foliar-applied agrochemicals can potentially be safer and more efficient than conventional products. However,limited understanding about how nanoparticle properties influence their interactions with plant leaves, uptake, translocation through the mesophyll to the vasculature, and transport to the rest of the plant prevents rational design. This study used a combination of Auquantification and spatial analysis to investigate how size (3, 10, or50 nm) and coating chemistry (PVP versus citrate) of gold nano-particles (AuNPs) influence these processes. Following wheat foliar exposure to AuNPs suspensions (~280 ng per plant), adhesion on the leaf surface was increased for smaller sizes, and PVP-AuNPs compared to citrate-AuNPs. After 2 weeks, there was incomplete uptake of citrate-AuNPs with some AuNPs remaining on the outside of the cuticle layer. However, the fraction of citrate-AuNPs that had entered the leaf was translocated efficiently tothe plant vasculature. In contrast, for similar sizes, virtually all of the PVP-AuNPs crossed the cuticle layer after 2 weeks,but its transport through the mesophyll cells was lower. As a consequence of PVP-AuNP accumulation in the leaf mesophyll, wheat photosynthesis was impaired. Regardless of their coating and sizes, the majority of the transported AuNPs accumulated in younger shoots (10-30%) and in roots (10-25%), and 5-15% of the NPs <50 nm were exuded into the rhizosphere soil. A greater fraction of larger sizes AuNPs (presenting lowerζpotentials) was transported to the roots. The key hypotheses about the NPs physical-chemical and plant physiology parameters that may matter to predict leaf-to-rhizosphere transport are also discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1976

Ceramic thermal-barrier coatings for cooled turbines

Ceramic thermal-barrier coatings on hot engine parts have the potential to reduce metal temperatures, coolant requirements, cost, and complexity of the cooling configuration, and to increase life, turbine efficiency and gas temperature. Coating systems consisting of a plasma-sprayed layer of zirconia stabilized with either yttria, magnesia or calcia over a thin alloy bond coat have been developed, their potential analyzed and their durability and benefits evaluated in a turbojet engine. The coatings on air-cooled rotating blades were in good condition after completing as many as 500 two-minute cycles of engine operation between full power at a gas temperature of 1644 K and flameout, or as much as 150 hours of steady-state operation on cooled vanes and blades at gas temperatures as high as 1644 K witn 35 start and stop cycles. On the basis of durability and processing cost, the yttria-stabilized zirconia was considered the best of the three coatings investigated.

Liebert, C. H.↗

NASA NTRS1996

Processing and Properties of Fiber Reinforced Polymeric Matrix Composites: Processing Robustness of IM7/PETI Polyimide Composites - Part 2

The processability of a phenylethynyl terminated imide (PETI) resin matrix composite was investigated. Unidirectional prepregs were made by coating an N-methylpyrrolidone solution of the amide acid oligomer onto unsized IM7. Two batches of prepregs were used: one was made by NASA in-house, and the other was from an industrial source. The composite processing robustness was investigated with respect to the effect of B-staging conditions, the prepreg shelf life, and the optimal processing window. Rheological measurements indicated that PETI's processability was only slightly affected over a wide range of B-staging temperatures (from 250 C to 300 C). The open hole compression (OHC) strength values were statistically indistinguishable among specimens consolidated using various B-staging conditions. Prepreg rheology and OHC strengths were also found not to be affected by prolonged (i.e., up to 60 days) ambient storage. An optimal processing window was established using response surface methodology. It was found that IM7/PETI composite is more sensitive to the consolidation temperature than to the consolidation pressure. A good consolidation was achievable at 371 C/100 Psi, which yielded an OHC strength of 62 Ksi at room temperature. However, processability declined dramatically at temperatures below 350 C.

Hou, Tan-Hung↗

DOE OSTI2019

Knittable and Washable Multifunctional MXene-Coated Cellulose Yarns

Textile-based electronics enable the next generation of wearable devices, which have the potential to transform the architecture of consumer electronics. Highly conductive yarns that can be manufactured using industrial-scale processing and be washed like everyday yarns are needed to fulfill the promise and rapid growth of the smart textile industry. By coating cellulose yarns with Ti 3 C 2 T x MXene, highly conductive and electroactive yarns are produced, which can be knitted into textiles using an industrial knitting machine. It is shown that yarns with MXene loading of ≈77 wt% (≈2.2 mg cm -1 ) have conductivity of up to 440 S cm -1 . After washing for 45 cycles at temperatures ranging from 30 to 80 °C, MXene-coated cotton yarns exhibit a minimal increase in resistance while maintaining constant MXene loading. The MXene-coated cotton yarn electrode offers a specific capacitance of 759.5 mF cm -1 at 2 mV s -1 . Additionally, a fully knitted textile-based capacitive pressure sensor is also prepared, which offers high sensitivity (gauge factor of ≈6.02), wide sensing range of up to ≈20% compression, and excellent cycling stability (2000 cycles at ≈14% compression strain). This work provides new and practical insights toward the development of platform technology that can integrate MXene in cellulose-based yarns for textile-based devices.

36 MATERIALS SCIENCE↗

NASA NTRS2011

Differential Processing of Low and High LET Radiation Induced DNA Damage: Investigation of Switch from ATM to ATR Signaling

The members of the phosphatidylinositol kinase-like kinase family of proteins namely ataxia-telangiectasia mutated (ATM) and ATM- and Rad3-related (ATR) are directly responsible for the maintenance of genomic integrity by mounting DDR through signaling and facilitating the recruitment of repair factors at the sites of DNA damage along with coordinating the deployment of cell cycle checkpoints to permit repair by phosphorylating Checkpoint kinase Chk1, Chk2 and p53. High LET radiation from GCR (Galactic Cosmic Rays) consisting mainly of protons and high energy and charged (HZE) particles from SPE (Solar Particle Event) pose a major health risk for astronauts on their space flight missions. The determination of these risks and the design of potential safeguards require sound knowledge of the biological consequences of lesion induction and the capability of the cells to counter them. We here strive to determine the coordination of ATM and ATR kinases at the break sites directly affecting checkpoint signaling and DNA repair and whether differential processing of breaks induced by low and high LET radiation leads to possible augmentation of swap of these damage sensors at the sites of DNA damage. Exposure of cells to IR triggers rapid autophosphorylation of serine-1981 that causes dimer dissociation and initiates monomer formation of ATM. ATM kinase activity depends on the disruption of the dimer, which allows access and phosphorylation of downstream ATM substrates like Chk2. Evidence suggests that ATM is activated by the alterations in higher-order chromatin structure although direct binding of ATM to DSB ends may be a crucial step in its activation. On the other hand, in case of ATR, RPA (replication protein A)-coated ssDNA (single-stranded DNA) generated as a result of stalled DNA replication or during processing of chromosomal lesions is crucial for the localization of ATR to sites of DNA damage in association with ATR-interacting protein (ATRIP). Although the majority of RPA-coated ssDNA is generally present only during DNA replication, ATR activation in G1 and G2-phase might still require formation of RPA-coated ssDNA, probably initiated by the MRN-CtIP complex and then extended by the Exo1- or BLM-dependent mechanisms at the sites of DSBs. Evidence accumulates that activation of ATM and ATR are oppositely regulated by the length of single stranded overhangs generated at the break sites by processes mentioned above and these stretches of single stranded overhangs hold the clue for ATM to ATR switch at broken DNA ends. We irradiated 82-6hTERT human fibroblast cells with low LET gamma-rays and high LET Fe and Si particles. Preliminary results with cells exposed to 1Gy gamma-rays show that the kinetics of pChk2-pT68 foci formation is comparable to that of gamma-H2AX although they appear to recede quicker. The number and intensity of observed foci reaches a maximum at 30 min and 60 min post IR for Chk2-pT68 and gamma-H2AX foci respectively and all Chk2-pT68 foci colocalize with gamma-H2AX foci. The kinetics of Chk1-pS345 and ATRIP are being determined. Results of Chk2-pT68 foci kinetics was also corroborated by western blot experiments, although phosphorylation was detected as early as 10 min and started receding 30 min post IR with 2Gy of gamma-rays. On the other hand, level of ATR-pS428 reached its maximum between 60 and 120 min and was maintained until the last measured time point of 4 hours post IR as determined by western blotting. Experiments performed with high LET Fe and Si particles will be reported.

Saha, Janapriya↗

DOE OSTI2018

Following the Morphological Disruption by an Electrolyte of a Buried Interface

A challenge of broad interest in both materials science and biology is the study of interfaces that are buried within a structure, particularly multilayer structures. Despite the enormous costs of corrosion and many decades of corrosion research, details of the mechanisms of various sorts of corrosion are still not clear, in part due to the difficulty in interrogating the interface between the corroding metal and an organic coating, which is typically used to mitigate corrosion. Generally, the performance of such coatings is evaluated by visual inspection after exposure or by modeling impedance data, which is a process not straightforwardly connected to physical interface structures. "Rocking-curve" X-ray scattering measurements provide a means of probing such interfaces due to the ability of X-rays to penetrate materials. Here, variations in the morphology of an interface between a protective coating and a metal substrate due to exposure to an electrolyte are derived from analysis of rocking-curve data in conjunction with atomic force microscopy imaging of the outer coating surface. The interfaces of cross-linked epoxy coatings with aluminum are irreversibly changed after 12 h of contact between the electrolyte solution and the face of the coating. The character of this change varies with the molecule used to cross-link the coating. Since X-ray off-specular scattering is sensitive to changes on the nanometer scale, it is also able to register interface degradation on time scales shorter than those probed by many other techniques, potentially expediting the evaluation of coatings for protection against degradation of the interface.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Interfacial solvation-structure regulation for stable Li metal anode by a desolvation coating technique

Rechargeable lithium (Li) metal batteries face challenges in achieving stable cycling due to the instability of the solid electrolyte interphase (SEI). The Li-ion solvation structure and its desolvation process are crucial for the formation of a stable SEI on Li metal anodes and improving Li plating/stripping kinetics. This research introduces an interfacial desolvation coating technique to actively modulate the Li-ion solvation structure at the Li metal interface and regulate the participation of the electrolyte solvent in SEI formation. Through experimental investigations conducted using a carbonate electrolyte with limited compatibility to Li metal, the optimized desolvation coating layer, composed of 12-crown-4 ether-modified silica materials, selectively displaces strongly coordinating solvents while simultaneously enriching weakly coordinating fluorinated solvents at the Li metal/electrolyte interface. This selective desolvation and enrichment effect reduce solvent participation to SEI and thus facilitate the formation of a LiF-dominant SEI with greatly reduced organic species on the Li metal surface, as conclusively verified through various characterization techniques including XPS, quantitative NMR, operando NMR, cryo-TEM, EELS, and EDS. The interfacial desolvation coating technique enables excellent rate cycling stability (i.e., 1C) of the Li metal anode and prolonged cycling life of the Li||LiCoO 2 pouch cell in the conventional carbonate electrolyte (E/C 2.6 g/Ah), with 80% capacity retention after 333 cycles.

42 ENGINEERING↗

DOE OSTI2023

Macroscale Superlubricity Induced by MXene/MoS 2 Nanocomposites on Rough Steel Surfaces under High Contact Stresses

Toward the goal of achieving superlubricity, or near-zero friction, in industrially relevant material systems, solution-processed multilayer Ti 3 C 2 T x -MoS 2 blends are spray-coated onto rough 52100-grade steel surfaces as a solid lubricant. The tribological performance was assessed in a ball-on-disk configuration in a unidirectional sliding mode. The test results indicate that Ti 3 C 2 T x -MoS 2 nanocomposites led to superlubricious states, which has hitherto been unreported for both individual pristine materials, MoS 2 and Ti 3 C 2 T x , under macroscale sliding conditions, indicating a synergistic mechanism enabling the superlative performance. Furthermore, the processing, structure, and property correlation were studied to understand the underlying phenomena. Raman spectroscopy, scanning electron microscopy, and transmission electron microscopy revealed the formation of an in situ robust tribolayer that was responsible for the performance at high contact pressures (>1.1 GPa) and sliding speeds (0.1 m/s). This report presents the lowest friction obtained by either MoS 2 or MXene or any combination of the two so far.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Process Innovations for High Temperature Superconducting (HTS) Wire Manufacturing

Thermal and strain cycling tests for STI’s coated conductor have been performed with our newly updated critical current/tensile tester. The original goal was to carry out 1000 thermal cycles and 1000 strain cycles and measure Ic for pre and post cycling. The tape exceeded the goal. Thermal testing was successful with 2900 cycles and strain testing was carried out for 2000 cycles without any significant Ic degradation. Another important milestone was to produce lengths greater than 100m, a 2X improvement over reported performance reported in Q4/2019 report was completed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2025

Reducing the Cost and Energy of Lithium-ion Battery Manufacturing using High Throughput Atomic Layer Deposition Processes

Forge Nano has recently developed an innovative strategy based on atomic layer deposition(ALD) of oxide coatings on battery separators and electrode materials. ORNL team worked with Forge Nano under this CRADA to construct larger format cells, validate battery and separator performance, and perform advanced materials characterization. It was observed that oxide coatings improve the battery cell performance in terms of both rate capability and long-term cyclic stability. ORNL team performed the research under this CRADA at DOE’s Battery Manufacturing Facility (BMF) at ORNL.

25 ENERGY STORAGE↗

DOE OSTI2025

Reducing the Cost and Energy of Lithium-ion Battery Manufacturing using High Throughput Atomic Layer Deposition Processes

Forge Nano has recently developed an innovative strategy based on atomic layer deposition (ALD) of oxide coatings on battery separators and electrode materials. ORNL team worked with Forge Nano under this CRADA to construct larger format cells, validate battery and separator performance, and perform advanced materials characterization. It was observed that oxide coatings improve the battery cell performance in terms of both rate capability and long-term cyclic stability. ORNL team performed the research under this CRADA at DOE’s Battery Manufacturing Facility (BMF) at ORNL.

25 ENERGY STORAGE↗

NASA NTRS1977

Spraylon fluorocarbon encapsulation for silicon solar cell arrays

A development program was performed for evaluating, modifying, and optimizing the Lockheed formulated liquid transparent filmforming Spraylon fluorocarbon protective coating for silicon solar cells and modules. The program objectives were designed to meet the requirements of the low-cost automated solar cell array fabrication process. As part of the study, a computer program was used to establish the limits of the safe working stress in the coated silicon solar cell array system under severe thermal shock.

Source record↗

DOE OSTI2022

Anticorrosive epoxy coatings from direct epoxidation of bioethanol fractionated lignin

The development of lignin-based anticorrosive epoxy coatings for steel protection is beneficial for both alleviating the fossil resource depletion and value-added utilization of lignin but remains a challenge due to the inherent heterogeneous structure of lignin. Here, in this study, we selectively extract the low molecular weight (MW) fraction of a crop residue-derived enzymatic hydrolysis lignin (EHL) through a bioethanol fractionation process and prepare epoxy resin by direct epoxidation of the bioethanol fractionated lignin (BFL). The coatings are then fabricated using 20–100 wt% of BFL-based epoxy resin (LEp) as the commercial epoxy resin substitute. The low MW and high p-hydroxyphenyl content of the BFL offer high solubility and good workability for BFL and LEp during epoxidation and coating production, respectively. Lignin-based coatings with 20–40 wt% LEp exhibit good adhesion property (5B) and superior corrosion resistance, compared to the commercial epoxy coating. Although coating with high LEp concentrations (i.e., 60–100 wt%) resulted in decreased adhesion strength, the coating with 100 wt% LEp still displayed corrosion protection performance comparable to that of the commercial epoxy coating. Overall, this study provides a simple and effective approach to converting lignin to epoxy resins for a wide variety of surface coating applications.

09 BIOMASS FUELS↗

DOE OSTI2025

Two-step spin-coating of vacancy-ordered double perovskites enables growth of thin films for electronic devices

Vacancy-ordered double perovskites (VODPs), such as Cs 2 TeX 6 (X = Cl, Br, I), are lead-free alternatives to conventional metal-halide perovskites (MHPs). One limitation of VODPs is the lack of processes to form thin films relevant for physical characterization and electronic devices. A two-step spin-coating method was developed for synthesizing high-quality films of Cs 2 TeBr 6 . Independently depositing CsBr and TeBr 4 enables high precursor concentrations and control over crystallization kinetics. By optimizing the spin-coating parameters, conversion of precursors to phase pure films was observed using structural and surface characterization methods. The growth of mixed-halide systems was investigated using alternative salts including CsCl and CsI. The formation of halide alloys was found to depend on the existence of routes to byproducts. Lastly, single carrier diodes of Cs2TeBr6 were designed following valence band characterization with photoelectron spectroscopy. Temperature-dependent space-charge-limited current measurements revealed that transport occurs by hopping and the hole mobility is 3.2 × 10 −5 cm 2 V −1 s −1 near room temperature. As a result, the insights from the 2-step procedure provide a pathway towards making semiconducting devices from VODPs.

Kuklinski, Owen [University of California, Santa B↗

DOE OSTI2023

Modifying Surface Chemistry to Enhance the Electrochemical Stability of Nickel‐Rich Cathode Materials

Residual impurities such as lithium carbonate and hydroxide are a major concern for accelerating parasitic reactions at the cathode electrolyte interface of lithium-ion batteries. Removal of these lithium-bearing species becomes a necessity for high-performance nickel-rich cathode materials. Instead of directly removing these impurities through washing steps, a wet impregnation process is employed to convert these detrimental surface impurities into beneficial surface coating on nickel-rich cathode materials. Specifically, the pristine cathode material is treated with Al(H 2 PO 4 ) 3 solution to convert undesired compounds into Li 3 PO 4 and AlPO 4 , both of which are considered positive surface coating materials for high-voltage cathodes. It is found that the introduced modification greatly suppresses the interfacial impedance hike and improves the capacity retention of the cathode material after repeating charging/discharging. It is believed that these benefits are realized through the modification of the surface chemistry of the cathode material, which helps to slow down the parasitic reactions and reduce the damage to the cathode material.

25 ENERGY STORAGE↗

DOE OSTI2019

Efficient Solar‐Thermal Distillation Desalination Device by Light Absorptive Carbon Composite Porous Foam

Abstract Solar‐thermal driven desalination based on porous carbon materials has promise for fresh water production. Exploration of high‐efficiency solar desalination devices has not solved issues for practical application, namely complicated fabrication, cost‐effectiveness, and scalability. Here, direct solar‐thermal carbon distillation (DS‐CD) tubular devices are introduced that have a facile fabrication process, are scalable, and use an inexpensive but efficient microporous graphite foam coated with carbon nanoparticle and superhydrophobic materials. The “black” composite foam serving as a solar light absorber heats up salt water effectively to produce fresh water vapor, and the superhydrophobic surface of the foam traps the liquid feed in the device. Two proof‐of‐principle distillation systems are adopted, i.e., solar still and membrane distillation and the fabricated devices are evaluated for direct solar desalination efficiency. For the solar still, nanoparticle and fluorosilane coatings on the porous surface increase the solar energy absorbance, resulting in a solar‐steam generation efficiency of 64% from simulated seawater at 1 sun. The membrane distillation demonstrates excellent vapor production (≈6.6 kg m ‐2 h ‐1 ) with >99.5% salt rejection under simulated 3 sun solar‐thermal irradiation. Unlike traditional solar desalination, the adaptable DS‐CD can easily be scaled up to larger systems such as high‐temperature tubular modules, presenting a promising solution for solar‐energy‐driven desalination.

42 ENGINEERING↗