Search NASA⌕ Search

SEARCH · Search NASA

Results for “Design Parameters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

Prediction Model for the Life of Nickel-cadmium Batteries in Geosynchronous Orbit Satellites

A mathematical model is described which predicts the service life of nickel-cadmium batteries designed for geosynchronous orbit satellites. Regression analysis technique is used to analyze orbital data on second generation trickle charged batteries. The model gives average cell voltage as a function of design parameters, operating parameters and time. The voltage model has the properties of providing a good fit to the data, good predictive capability, and agreement with known battery performance characteristics. Average cell voltage can be predicted to within 0.02 volts for up to 8 years. This modeling shows that these batteries will operate reliably for 10 years. Third-generation batteries are expected to operate even longer.

Engleman, J. H.↗

Nozzle optimization study for quiet supersonic wind tunnels

In the present study of the effects of operational factors and nozzle design parameters on the size of the quiet test section in several Mach 3.5 wind tunnel nozzles, the test results from a rapid expansion pilot nozzle with boundary layer removal slots upstream of the throat have shown that the low stream noise levels required for transition research are only obtainable with laminar nozzle wall boundary layers. Six different nozzles were evaluated, including a flat wall radial flow nozzle and a novel rod-wall nozzle. Attention is given to rms surface finish effects on quiet test region length.

Beckwith, I. E.↗

Large-diameter astromast development

The 15-m-long by 0.75-diameter deployable supermast was delivered. The performance characteristics, design parameters, and developmental work associated with this mast are described. The main differences, besides the length of these two mast sections, are a change in the longeron material (the principal structural member) to a circular cross section and the incorporation of a lanyard-bridle system which makes unaided deployment and retraction possible in zero gravity.

Finley, L. A.↗

Design and Performance of Sampled Data Loops for Subcarrier and Carrier Tracking

Design parameters and resulting performance are presented for the sampled data analogies of continuous time phase locked loops of second and third order containing perfect integrators. Expressions for noise equivalent bandwidth and steady state errors are given. Stability and gain margin are investigated using z plane root loci. Finally, an application is presented for Voyager subcarrier and carrier tracking under the dynamics of the encounters with Uranus and Neptune. For carrier tracking, loop bandwidth narrow enough for satisfactory loop signal to noise ratios can be achieved using third order loops without rate aiding, whereas second order loops would require aiding. For subcarrier tracking, third order loops can be used when the sampling rate is limited to approximately once per second, as in the Baseband Assembly, whereas second order loops sufficiently wide to track the dynamics have stability problems at that sampling rate.

Aguirre, S.↗

Study Proposal for the Possible Use of ISS as an Aerodynamic Facility for Aerospace Applications

In order to determine the correct design parameters for an orbital transfer vehicle (OTV) to be used in conjunction with the envisaged space station system (SSS) it is essential to know the aerodynamic coefficients in the translational flow regime of the Earth's atmosphere at approximately 80 to 200 km. Because of the inherent difficulties relating to the duplication of the abovesaid translational flow regime in a ground based aerodynamic facility, another means of making this determination had to be developed. The proposed solution is the exploitation of the tether satellite system (TSS). By employing it as a spaceborne variable low density wind tunnel, the TSS appears to be a very appealing tool for such gas dynamic research.

Buonjiolno, C.↗

Optimum dimensions of power solenoids for magnetic suspension

Design optimization of power solenoids for controllable and stabilizable magnetic suspensions with force compensation in a wind tunnel is shown. It is assumed that the model of a levitating body is a sphere of ferromagnetic material with constant magnetic permeability. This sphere, with a radius much smaller than its distance from the solenoid above, is to be maintained in position on the solenoid axis by balance of the vertical electromagnetic force and the force of gravitation. The necessary vertical (axial) force generated by the solenoid is expressed as a function of relevant system dimensions, solenoid design parameters, and physical properties of the body. Three families of curves are obtained which depict the solenoid power for a given force as a function of the solenoid length with either outside radius or inside radius as a variable parameter and as a function of the outside radius with inside radius as a variable parameter. The curves indicate the optimum solenoid length and outside radius, for minimum power, corresponding to a given outside radius and inside radius, respectively.

Kaznacheyev, B. A.↗

Characteristic Elastic Systems of Time-Limited Optimal Maneuvers

Optimizing an elastic system and its active control is discussed. Maneuvers from an initial state to a final state in a finite time interval are considered. An active generalized control force that accomplishes the desired maneuver of a prespecified system is optimal if it minimizes a given quadratic cost function. By also varying a set of design parameters, the elastic system can be determined so as to further minimize the cost function. Here, the elastic system that minimizes the actual control cost is compared with the system that minimizes the ratio of actual cost to the cost of optimally maneuvering a rigid system of the same inertial properties. It is shown that an elastic system corresponding to an extremum of the ratio is actually a characteristic of the time-limited maneuver. Because both the spatial domain and the time interval are fixed, a characteristic elastic system is tuned to the specified temporal boundary conditions. The implication for rest-to-rest, spinup, and spin reversal maneuvers of spacecraft is that the optimal control for a characteristic elastic spacecraft is identical to the optimal control for the same spacecraft as if it were rigid.

Hale, A. L.↗

Modeling a high energy gamma-ray telescope

A Monte Carlo program was developed to simulate a high energy gamma-ray telescope using a coded aperture mask (CAMTRAC). The ultimate purpose of the calculation will be to determine the optimum design parameters for such an instrument. The model can also used to ascertain under what conditions CAMTRAC performance is superior to that of conventional telescopes which employ electron-positron pair direction as the sole means of determining gamma ray direction.

Jenkins, T. L.↗

Proposed design class of grazing incidence echelle spectrometers - Critical analysis and reevaluation

The class of miltibounce grazing spectrometers proposed by Cash (1982) and by McClintock and Cash (1982) is analyzed, and performance values significantly lower than asserted by these authors are found. Ray tracing calculations used to examine the design parameters given in the above papers are reported, as is the efficiency which results from use of accepted reflectance data. Several schemes which can improve some of the performance parameters are indicated.

Hettrick, M. C.↗

Simple performance model for ring and line cusp ion thrusters

A model is developed for high magnetic field strength cusped thrusters which results in a single equation describing the thruster performance. Such a simple result is made possible by formulating the model in terms of the average energy expended in producing ions in the discharge plasma and the fraction of these ions that are extracted into the beam. A key feature of the model is that it allows one to calculate the average plasma ion energy cost as a function of the propellant utilization knowing only thruster geometric design parameters and the propellant gas. The model is exercised to indicate the effects on performance resulting from changes in the extracted ion fraction, the quality of the containment of primary electrons, the propellant mass flow rate, the propellant gas and the transparency of the accelerator system to neutral atoms.

Brophy, J. R.↗

Differential detection of Gaussian MSK in a mobile radio environment

Minimum shift keying with Gaussian shaped transmit pulses is a strong candidate for a modulation technique that satisfies the stringent out-of-band radiated power requirements of the mobil radio application. Numerous studies and field experiments have been conducted by the Japanese on urban and suburban mobile radio channels with systems employing Gaussian minimum-shift keying (GMSK) transmission and differentially coherent reception. A comprehensive analytical treatment is presented of the performance of such systems emphasizing the important trade-offs among the various system design parameters such as transmit and receiver filter bandwidths and detection threshold level. It is shown that two-bit differential detection of GMSK is capable of offering far superior performance to the more conventional one-bit detection method both in the presence of an additive Gaussian noise background and Rician fading.

Simon, M. K.↗

Evaluation of thermal control surface on-orbit servicing methods for long term missions

Future activities of NASA will include the long-term (10 - 30 years) operation of space vehicles. For this reason, there will be an urgent need to provide the basic technology for space vehicle thermal control surfaces and their functional maintenance for future long-term missions. One of the problems arising in connection with such missions is related to contamination which can degrade operational design parameters of critical and thermal control surfaces. All Space Based Payloads will arrive on orbit with a certain level of contamination from ground handling, and, on orbit, will be subjected to some level of contamination over their mission life. For the extension of mission life, it appears practical to institute surface refurbishment procedures for contaminated and degraded surfaces. Potential resurfacing methods are evaluated, taking into account three potential processes. The most promising of these is a cleaning procedure based on the utilization of atomic oxygen.

Saylor, W.↗

Design considerations for a 10-kW integrated hydrogen-oxygen regenerative fuel cell system

Integration of an alkaline fuel cell subsystem with an alkaline electrolysis subsystem to form a regenerative fuel cell (RFC) system for low earth orbit (LEO) applications characterized by relatively high overall round trip electrical efficiency, long life, and high reliability is possible with present state of the art technology. A hypothetical 10 kW system computer modeled and studied based on data from ongoing contractual efforts in both the alkaline fuel cell and alkaline water electrolysis areas. The alkaline fuel cell technology is under development utilizing advanced cell components and standard Shuttle Orbiter system hardware. The alkaline electrolysis technology uses a static water vapor feed technique and scaled up cell hardware is developed. The computer aided study of the performance, operating, and design parameters of the hypothetical system is addressed.

Hoberecht, M. A.↗

Advances in Joining Techniques Used in Development of SPF/DB Titanium Sandwich Reinforced with Metal Matrices

Three and four-sheet expanded titanium sandwich sheets have been developed at Douglas Aircraft Company, a division of McDonnell Douglas Corporation, under contract to NASA Langley Research Center. In these contracts, spot welding and roll seam welding are used to join the core sheets. These core sheets are expanded to the face sheets and diffusion bonded to form various type cells. The advantages of various cell shapes and the design parameters for optimizing the wing and fuselage concepts are discussed versus the complexity of the spot weld pattern. In addition, metal matrix composites of fibers in an aluminum matrix encapsulated in a titanium sheath are aluminum brazed successfully to the titanium sandwich face sheets. The strength and crack growth rate of the superplastic-formed/diffusion bonded (SPF/DB) titanium sandwich with and without the metal matrix composites are described.

Fischler, J. E.↗

Definition phase for thermal ion dynamics experiment for OPEN

The Thermal Ion Dynamics Experiment (TIDE) combines differential measurements of angle, energy, and mass to determine the detailed distribution function of low energy magnetospheric ions in the range of 0 to 100 eV. Goals included designing a 1 sq cm entrance aperture, minimizing trajectory divergence at exist aperture, and minimizing internal scattering. Design parameters were used to construct the test model.

Sharp, W. E.↗

Superconducting magnet

Extensive computer based engineering design effort resulted in optimization of a superconducting magnet design with an average bulk current density of approximately 12KA/cm(2). Twisted, stranded 0.0045 inch diameter NbTi superconductor in a copper matrix was selected. Winding the coil from this bundle facilitated uniform winding of the small diameter wire. Test coils were wound using a first lot of the wire. The actual packing density was measured from these. Interwinding voltage break down tests on the test coils indicated the need for adjustment of the wire insulation on the lot of wire subsequently ordered for construction of the delivered superconducting magnet. Using the actual packing densities from the test coils, a final magnet design, with the required enhancement and field profile, was generated. All mechanical and thermal design parameters were then also fixed. The superconducting magnet was then fabricated and tested. The first test was made with the magnet immersed in liquid helium at 4.2K. The second test was conducted at 2K in vacuum. In the latter test, the magnet was conduction cooled from the mounting flange end.

Source record↗

SSME Seal Test Program: Test results for sawtooth pattern damper seal

Direct and transverse force coefficients for 11, sawtooth-pattern, and damper-seal configurations were examined. The designation damper seal uses a deliberately roughened stator and smooth rotor to increase the net damping force developed by a seal. The designation sawtooth-pattern refers to a stator roughness pattern. The sawtooth pattern yields axial grooves in the stator which are interrupted by spacer elements which act as flow constrictions or dams. All seals use the same smooth rotor and have the same, constant, minimum clearance. The stators examined the consequences of changes in the following design parameters: (1) axial-groove depth; (2) number of teeth: (3) number of sawtooth sections; (4) number of spacer elements; (5) dam width; (6) axially aligned sawtooth sections versus axially-staggered sawtooth sections; and (7) groove geometry. It is found that none of the sawtooth-pattern seal performs as well as the best round-hole-pattern seal. Maximum damping configurations for the sawtooth and round-hole-pattern stators have comparable stiffness performance. Several of the sawtooth pattern stators outperformed the best round-hole pattern seal.

Childs, D. W.↗