Search NASA⌕ Search

SEARCH · Search NASA

Results for “Material Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

EVALUATION OF TGA AS A QUALITY ASSURANCE TOOL FOR SURFACEMODIFIED ZIRCOLOY-4

Thermogravimetric analysis (TGA) and coupled Mass Spectroscopy (MS) were evaluated to determine their suitability as a quality assurance tool for surface modified nickel plated zircaloy-4 liner tubes. Samples with 0, 0.1, 0.2, 0.3, and 0.4 mils of heat treated nickel plate were tested at 330, 370, and 400 C. Not all of the samples exhibited the expected typical parabolic shaped oxidation curve. The measured weight change was consistent for the as received and 0.2 mil and the 0.4 mil surface modified samples. None of the samples were tested under aggressive enough conditions to consume the surface modified materials during the test duration. Use of the Mass Spectrometer in conjunction with the TGA did not produce valuable data and was only used for the 400 C test series; however, the TGA was valuable. The 0.1 and 0.3 mil surface modified Zr-4 samples exhibited thru surface modified layer cracks which could account for the variation in oxidation behavior. TGA tests for periods up to six hours appear viable as a method to ascertain oxidation behavior for consistent results. Additional testing of samples with known variations in surface modified layer thickness and quality is recommended as part of the QA acceptance testing.

36 MATERIALS SCIENCE↗

High Temperature Oxidation Issues in Fossil Boilers

This report covers the conclusion of a multi-year project that examined the oxidation resistance of Al-rich coatings and a new project examining the effect of higher CO{sub 2} contents on corrosion mechanisms in oxy-fired coal-fueled boilers. The coating work primarily examined diffusion coatings for the steam side of typical ferritic (9-12%Cr) and austenitic (e.g., Type 304L) tube materials in accelerated testing at 650-800 C in wet air. The final phase of this work has attempted to obtain additional coating failures to determine a critical Al content (at coating failure) as a function of exposure temperature. However, no failures have been observed for austenitic substrates including >25 kh at 700 C and >6 kh at 800 C. Preliminary results are presented from the oxy-firing project, where the initial focus is on ferritic alloys. Initial coal-ash experiments were conducted at 600 C to evaluate some of the test parameters and three different levels of CO{sub 2} were investigated. An in-situ creep rig is being constructed to evaluate the effect of environment on creep properties. Initial ex-situ creep experiments are presented as a baseline.

01 COAL, LIGNITE, AND PEAT↗

Shell Element Material Model Verification Problems for DYNA3D: Part II

A suite of supplementary shell element material model verification tests were developed for the explicit finite element program DYNA3D, in continuation of the work performed in LLNL-TR-792469 (Shell Element Material Model Verification Problems for DYNA3D). The testing procedure developed in the preceding report is extended, and used to verify all remaining untested shell model features and inputs. A collection of 78 feature-specific verification tests are proposed, some of which are applicable to multiple material models, though many are specialized to a particular model. The collective suite of tests cover all 27 currently available material models in DYNA3D. In the course of developing the proposed test suite, 24 separate shell model-related issues were identified and have subsequently been resolved.

42 ENGINEERING↗

FY2021 Improvements to the New CTH Code Verification & Validation Test Suite

Over the past few years, the CTH multiphysics hydrocode has overhauled its software quality and testing processes, implementing current best practices in software quality and building a robust V&V test suite comprised of traditional hydrocode verification problems, including ASC Tri-Lab Test Suite and Enhanced Tri-Lab Test Suite problems, as well as validation problems for some of CTH’s most frequently used equations of state, materials models, and other key capabilities. Substantial progress towards building this new test suite was made in FY19 and FY20. In FY21, the test suite has been expanded to include verification and validation tests of the Steinberg-Guinan-Lund (ST) viscoplastic model and the Johnson Cook (JFRAC) fracture model. Additionally, two new verification tests were added, covering hydrodynamics and high explosive (HE) modeling capabilities: the Kidder Gaussian density problem and the Escape of HE Products (EHEP) problem from the Tri-Lab Test Suite. This report discusses each of these test problems in detail. Verification test results are compared to analytic solutions. Validation test results are compared to experimental data. Wherever possible, convergence or mesh refinement studies are included. Additionally, while implementing the Kidder verification problem, a bug was identified that affects the use of tables to initialize pressure or density in 1D or 2D calculations. A brief discussion of the bug and its fix is included. CTH demonstrates good performance overall on the new test suite problems. Simulation results showed good agreement with analytic solutions for the Kidder problem, with convergence rates ranging between 1.8 and sub-linear, and relatively good agreement for the EHEP problem, though convergence rates for pressure and density were nearly 0. The ST and JFRAC strain rate loading verification tests show good agreement with analytic solutions. Likewise, CTH simulation results show good agreement with experimental validation data, including Taylor rod impact testing, for the materials tested. Future V&V work will focus on adding 2D and 3D versions of existing verification tests as well as adding validation tests of other frequently used capabilities such as other fracture models.

42 ENGINEERING↗

Design of a Particle Shadow-graph Velocimetry and Size (PSVS) System to Determine Particle Size and Density Distributions in Hanford Nuclear Tank Wastes - 12280

Accurate particle size and density distributions for nuclear tank waste materials are essential information that helps determine the engineering requirements for a host of waste management unit operations (e.g., tank mixing, pipeline transport, and filtration). The most prevalent approach for determining particle size and density distribution is highly laborious and involves identifying individual particles using scanning electron microscope/x-ray diffraction and then acquiring the density of the materials from the technical literature. Other methods simply approximate individual particle densities by assuming chemical composition, rather than obtaining actual measurements of particle density. To overcome these limitations, a Particle Shadow-graph Velocimetry and Size (PSVS) system has been designed to simultaneously obtain particle size and density distributions for a broad range of Hanford tank waste materials existing as both individual particles and agglomerates. The PSVS system uses optical hardware, a temperature-controlled settling column, and particle introduction chamber to accurately and reproducibly obtain images of settling particles. Image analysis software provides a highly accurate determination of both particle terminal velocity and equivalent spherical particle diameter. The particle density is then calculated from Newton's terminal settling theory. The PSVS system was designed to accurately image particle/agglomerate sizes between 10 and 1000 μm and particle/agglomerate densities ranging from 1.4 to 11.5 g/cm{sup 3}, where the maximum terminal velocity does not exceed 10 cm/s. Preliminary testing was completed with standard materials and results were in good agreement with terminal settling theory. Recent results of this method development are presented, as well as experimental design. The primary goal of these PSVS system tests was to obtain accurate and reproducible particle size and velocity measurements to estimate particle densities within 20 percent of direct measured density values. The average percent error observed in particle densities was 4.8, 8.2, and 25.8 percent for S1D3 (high-density soda-lime glass), S3D4 (zirconia), and S1D2 (soda-lime glass) beads, respectively. The maximum measured particle density error observed was 14.5, 21.0, and 58.4, for S1D3, S3D4, and S1D2 beads, respectively. Multiple sources of error can exist that contribute to inaccurate estimates of particle density using the PSVS approach. Two significant influences observed were thermal convective currents in the settling column fluid and non-spherical (irregular) particle shapes in the standard test materials. Experimental results using buoyant beads suggest thermal convective currents can influence the movement of settling particles as much as 4 mm/s. These thermal convective currents are clearly a significant concern for smaller and less-dense particles/agglomerates which have terminal velocities of the same magnitude. Significant effort went into the design and fabrication of a thermal control system for the PSVS settling column. However, small temperature variations (<0.3 deg. C) are difficult to prevent and measure accurately. Therefore, although designing the thermal control system was necessary, it is not considered the only solution to minimize error due to thermal convective currents. The use of small diameter (10 to 27 μm) polyethylene buoyant beads (in low concentrations) during actual settling experiments may be necessary to provide insight into particle-particle interactions and fluid velocity correction factors to account for potential influences from thermal convective currents. Future testing will incorporate the buoyant beads into the analysis technique when the suspension fluid is chemically compatible. The use of the Newton's law to calculate particle/agglomerate densities assumes spherical particle shapes. As the actual particle/agglomerates diverge from spherical, the margin of error increases. The selection of high quality (in density and shape) monodispersed particle standards was a direct attempt to reduce the uncertainties associated with non-spherical or irregular particles and to only observe the PSVS method and analysis error. While investigating the source of data scatter for the S1D3 bead (nominal 700 μm) standard, significant irregular particles where discovered. Yet, a subsequent investigation into the S3D4 bead standard was also conducted and it was determined that 60 percent of the particles had a 0.9 to 0.8 centricity, 32 percent were between 0.8 and 0.7, only 7 percent were between 1.0 and 0.9, and the remaining 1 percent of the particles had centricities between 0.7 and 0.6. Contrast this with the S1D3 bead standard, where 100 percent of particles had centricities between 0.95 and 0.98, upon applying the centricity filter. The influence of the non-spherical shape of the S3D4 bead standard is evident when comparing a 3.9 percent average density error for S1D3 glass bead standard with an 8.3 percent average density error for the S3D4 bead standard. Model corrections for non-spherical shape must be implemented to account for these measurement errors during future method validation and system performance assessments. In addition, further work is needed to resolve the higher than expected velocities for the smaller S1D2 particles. Initial measurements conducted with buoyant beads as fluid velocity tracers indicate that fluid velocities can be subtracted from the increased particle velocities to determine the particle terminal velocity, regardless of the surrounding fluid velocity. However, this approach is in its infancy and will need to be carefully and methodically validated. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The ephemeral and the enduring: Trajectories of disappearance for the scientific objects of American Cold War nuclear weapons testing

Here, the historical material culture produced by American Cold War nuclear weapons testing includes objects of scientific inquiry that can be generally categorized as being either ephemeral or enduring. Objects deemed to be ephemeral were of a less substantial nature, being impermanent and expendable in a nuclear test, while enduring objects were by nature more durable and long-lasting. Although all of these objects were ultimately subject to disappearance, the processes by which they were transformed, degraded, or destroyed prior to their disappearing differ. Drawing principally upon archaeological theory, this paper proposes a functional dichotomy for categorizing and studying the historical trajectories of nuclear weapons testing technoscience artifacts. In examining the transformation patterns of steel towers and concrete blockhouses in particular, it explores an associated loss of scientific method that accompanies a science object's disappearance.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Hierarchically Structured Sulfur/Carbon Nanocomposite Material for High Energy Lithium Battery

We report herein a hierarchically structured sulfur-carbon (S/C) nanocomposite material as the high surface-area cathode for rechargeable lithium batteries. A porous carbon with a uniform distribution of mesopores of 7.3 nm has been synthesized through a soft-template synthesis method. The potassium hydroxide activation of this mesoporous carbon results in a bimodal porous carbon with added microporosity of less than 2 nm to the existing mesopores without deterioration of the integrity of the original mesoporous carbon. Elemental sulfur has been loaded to the micropores through a solution infiltration method. The resulted S/C composites with various loading level of sulfur have a high surface areas and large internal porosities. These materials have been tested as novel cathodes for Li/S batteries. The results show that the cyclability and the utilization of sulfur in the Li/S batteries have been significantly improved. The large internal porosity and surface area of the micro-mesoporous carbon is essential for retaining sulfur in the cathode and therefore maximizing the capacity and lifespan of the cathode.

25 ENERGY STORAGE↗

Development of Accelerated High Temperature Mechanical Testing Techniques

The Advanced Materials and Manufacturing Technologies (AMMT) Program focuses on advancing materials and manufacturing techniques for nuclear energy applications, particularly in the qualification of materials for high-temperature structural use. This report presents work on refining the creep testing of small specimen geometries. Efforts include the development of a new specimen geometry for sub-sized specimens, which were subjected to uniaxial creep tests. The results contribute to the understanding of material behavior under stress at elevated temperatures and offer potential improvements in creep data collection methods. These findings support ongoing advancements in material qualification processes essential for nuclear reactor applications.

36 MATERIALS SCIENCE↗

Convergent laser beam shapes: Unveiling the dynamics of Laser-induced elastic waves in composite materials

Overcoming the low signal-to-noise ratio (SNR) in laser ultrasonic testing of composite materials remains a significant challenge. Current efforts focus on enhancing SNR by inserting more energy into the material through temporal and/or spatial modulation of the laser beam. However, potential SNR improvements through wave convergence and wave energy manipulation have been overlooked. This paper addresses this gap by demonstrating the convergence of different wave types to a designated point and by showing the feasibility of directing absorbed laser energy into a specific wave type through spatial modulation of the laser beam. To achieve this, mathematical expressions for the convergent laser beams are derived. Various laser beam profiles are then introduced to the thermoelastic equations and solved using the finite element method. The sample under investigation is a transversely isotropic unidirectional carbon fiber reinforced plastic, characterized by anisotropic thermal expansion coefficients and thermal conductivities. Results reveal pronounced convergence of the intended wave type at the center due to laser beam shaping. This study showcases the ability to direct absorbed laser energy toward a specific wave type through spatial modulation of the laser beam and highlights the role of material anisotropy in energy focusing.

composite materials↗

Characterization of Shear Properties for APO/MBI Syntactic Foam

Triaxial compression testing is a means for mechanical characterization of a material. A unique feature of the triaxial compression test is the application of two different magnitudes of compressive pressures on the material simultaneously. The material behavior under these different compressive pressures can be monitored over time. Several important characteristics of the material, such as stress yield values and the shear failure envelope may then be determined. Also mechanical properties such as Poisson’s ratio, Young’s modulus and bulk modulus can be determined from the triaxial compression test. The triaxial compression test was employed in this investigation to characterize the shear behavior, shear failure envelope, and mechanical properties of a syntactic foam. Los Alamos National Laboratory (LANL) supplied a total of 36 samples of APO-BMI syntactic foam to the University of New Mexico, Department of Civil Engineering for testing between December 2003 and May 2004. Each sample had a diameter of 1.395±0.005 in. (3.543±0.013cm.) and a length of 2.796±0.004 in. (7.102±0.010 cm.). The samples had an average density of 0.295 g/cm3. Additional information about the material tested in this investigation can be found in the “Specimen Description” section contained in Chapter 1. The nomenclatures used in this study is presented in Chapter 1. In addition to designing and implementing triaxial compression tests capable of up to 2,000 psi. confining pressure (minor principal stress) and roughly 13,000 psi. in axial pressure (major principal stress), a pure tension test was designed and conducted on the foam material. The purpose of this pure tension test was to obtain maximum tensile stress values to enhance the characterization of the shear envelope in the stress space. The sampling procedure and specimen preparation for a standard test can be found in the American Society for Testing Materials (ASTM) D 5379/ D 5379 – 93. The above tests mentioned and their procedures are discussed in Chapter 2. Chapter 2 contains the types of tests performed and the apparatus used for testing the material. Chapter 2 also has a brief explanation of the equipment and the procedures used for conducting the tests. In Chapter 3, the material characteristics and mechanical properties obtained from the tests are described; composite plots of deviatoric vs. mean stress and deviatoric stress vs. longitudinal strain are also included. The plots of deviatoric stress vs. mean stress clearly identify the shear envelope for the material. Chapter 4 summarizes the vital information obtained from the tests and the conclusions made. All the necessary plots and the data generated during the testing have been included in the Appendix. The information in the appendix includes plots of: Strain vs. Time, Stress vs. Time, Stress vs. Strain, Mean Stress vs. Volumetric Strain, Lateral Strain vs. Longitudinal Strain, and q vs. p. Bulk modulus, Poisson’s ratio, and Young’s modulus are displayed in the appropriate plots in each appendix.

36 MATERIALS SCIENCE↗

Comparison of Calculated and Experimental Results for a Boiling/Condensing Experimental Facility

A new experimental facility is being developed for materials irradiation and testing at the Oak Ridge National Laboratory (ORNL) High Flux Isotope Reactor (HFIR). Details of this facility have been presented before. A prototype of this facility, the Thermosyphon Test Loop (TSTL) has been built, and experimental data have been obtained and analyzed. Pretest calculations for this facility with the RELAP5-3D code have been presented previously as well as other calculations with the TRACE code. The results of both codes were very different. RELAP5-3D predicted much higher pressures and temperatures than TRACE. This paper compares calculated results with the TSTL experimental data. Comparison of calculations with the codes RELAP5-3D and TRACE with experimental data of the new TSTL facility has shown that TRACE results agree well with the data and that RELAP5-3D calculates very high pressures and temperatures. The TRACE code is well suited to model this facility and is being used for future calculations. (authors)

42 ENGINEERING↗

Shell Element Material Model Verification Problems for DYNA3D

A suite of shell element material model verification tests were developed for the explicit finite element program DYNA3D. Each test consists of a single quadrilateral shell element, whose nodal displacements and rotations have been prescribed such that the deformation of the material is fully controlled throughout the analysis. At one of the element’s integration points, the numerically computed stress, through-thickness strain, and equivalent plastic strain are compared against closed-form reference solutions that are derived to be consistent with the theory of finite deformation elasto-plasticity. A collection of 31 feature-specific verification tests are proposed, each of which may be used to verify all models which share in common the tested feature of interest. For each material model, a subset of these tests are selected and used to verify the correct behavior of all features of the model. The collective suite of tests cover 26 of the 27 currently available material models in DYNA3D. In the course of developing the proposed test suite, 18 implementation bugs were identified and have subsequently been resolved.

42 ENGINEERING↗

Workhorse minimally empirical dispersion-corrected density functional with tests for weakly bound systems: r 2 SCAN + rVV 10

SCAN+rVV10 has been demonstrated to be a versatile van der Waals (vdW) density functional that delivers good predictions of both energetic and structural properties for many types of bonding. Recently, the r 2 SCAN functional was devised as a revised form of SCAN with improved numerical stability. In this work, we refit the rVV10 functional to optimize the r 2 SCAN+rVV10 vdW density functional and test its performance for molecular interactions and layered materials. Our molecular tests demonstrate that r 2 SCAN+rVV10 outperforms its predecessor SCAN+rVV10 in both efficiency (numerical stability) and accuracy. This good performance is also found in lattice-constant predictions. In comparison with benchmark results from higher-level theories or experiments, r 2 SCAN+rVV10 yields excellent interlayer binding energies and phonon dispersions for layered materials.

36 MATERIALS SCIENCE↗

Superlubricity in rolling/sliding contacts

Rolling element bearings and gears are critical components of mechanical systems such as wind turbines and automotive engines and transmissions that use oil-based lubricants. Oil-based lubricants used in these applications many times needs periodical replacement, which not only add more cost but also affects overall productivity. More importantly, the used oil generates hazardous waste creating huge environmental problem. In this study, we demonstrated that nanomaterials can be employed as solid lubricants in combination with diamond like carbon (DLC) films in dry nitrogen environment under rolling/sliding contacts. Using micro-pitting rig (MPR) that generally used to test and qualify materials and lubricants for bearings and gear systems for industrial applications, we have tested diamond like carbon (DLC) material pairs in an oil-free, dry nitrogen environment along with two dimensional (2D) MoS2 combined with nanodiamond as a solid lubricant. We show that superlubricity (traction coefficient of friction is 0.003) was achieved through the formation of a carbon rich superlubricious tribolayer at the interface reducing the overall friction by a minimum of 20 times and no surface damage as compared to Steel-Steel contacts lubricated with oil (0.06-0.07). The current work paves the way for developing oil-free solid lubricants in a variety of applications involving rolling/sliding contacts.

36 MATERIALS SCIENCE↗

Criteria for initiation of delamination in quasi-static punch-shear tests of a carbon-fiber composite material.

V arious phenomenological delamination initiation criteria are analyzed in quasi - static punch - shear tests conducted on six different geometries. These six geometries are modeled and analyzed using elastic, large - deformation finite element analysis. Analysis output is post - processed to assess different delamination initiation criteria, and their applicability to each of the geometries. These criteria are compared to test results to assess whether or not they are appropriate based on what occurred in testing. Further, examinations of CT scans and ultrasonic images o f test specimens are conducted in the appendix to determine the sequence of failure in each test geometry.

Chin, Eric Brian↗

Documentation pckage for the RFID temperature monitoring system (Of Model 9977 packages at NTS).

The technical basis for extending the Model 9977 shipping package periodic maintenance beyond the one-year interval to a maximum of five years is based on the performance of the O-ring seals and the environmental conditions. The DOE Packaging Certification Program (PCP) has tasked Argonne National Laboratory to develop a Radio-Frequency Identification (RFID) temperature monitoring system for use by the facility personnel at DAF/NTS. The RFID temperature monitoring system, depicted in the figure below, consists of the Mk-1 RFId tags, a reader, and a control computer mounted on a mobile platform that can operate as a stand-alone system, or it can be connected to the local IT network. As part of the Conditions of Approval of the CoC, the user must complete the prescribed training to become qualified and be certified for operation of the RFID temperature monitoring system. The training course will be administered by Argonne National Laboratory on behalf of the Headquarters Certifying Official. This is a complete documentation package for the RFID temperature monitoring system of the Model 9977 packagings at NTS. The documentation package will be used for training and certification. The table of contents are: Acceptance Testing Procedure of MK-1 RFID Tags for DOE/EM Nuclear Materials Management Applications; Acceptance Testing Result of MK-1 RFID Tags for DOE/EM Nuclear Materials Management Applications; Performance Test of the Single Bolt Seal Sensor for the Model 9977 Packaging; Calibration of Built-in Thermistors in RFID Tags for Nevada Test Site; Results of Calibration of Built-in Thermistors in RFID Tags; Results of Thermal Calibration of Second Batch of MK-I RFID Tags; Procedure for Installing and Removing MK-1 RFID Tag on Model 9977 Drum; User Guide for RFID Reader and Software for Temperature Monitoring of Model 9977 Drums at NTS; Software Quality Assurance Plan (SQAP) for the ARG-US System; Quality Category for the RFID Temperature Monitoring System; The Documentation Package for the RFID Temperature Monitoring System; Software Test Plan and Results for ARG-US OnSite; Configuration Management Plan (CMP) for the ARG-US System; Requirements Management Plan for the ARG-US System; and Design Management Plan for ARG-US.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The Benchmark Extensible Tractable Testbed Engineering Resource (BETTER)

The Benchmark Extensible Tractable Testbed Engineering Resource (BETTER) is proposed as a family of modular test bodies that are intended to support engineering capability development by helping to identify weaknesses and needs. Weapon systems, subassemblies, and components are often complex and difficult to test and analyze, resulting in low confidence and high uncertainties in experimental and simulated results. The complexities make it difficult to distinguish between inherent uncertainties and errors due to insufficient capabilities. BETTER test bodies will first use simplified geometries and materials such that testing, data collection, modeling and simulation can be accomplished with high confidence and low uncertainty. Modifications and combinations of simple and well-characterized BETTER test bodies can then be used to increase complexity in order to reproduce relevant mechanics and identify weaknesses. BETTER can provide both immediate and long-term improvements in testing and simulation capabilities. This document presents the motivation, concept, benefits and examples for BETTER.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Modeling Failure of Electrical Transformers due to Effects of a HEMP Event

Understanding the effect of a high-altitude electromagnetic pulse (HEMP) on the equipment in the United States electrical power grid is important to national security. A present challenge to this understanding is evaluating the vulnerability of transformers to a HEMP. Evaluating vulnerability by direct testing is cost-prohibitive, due to the wide variation in transformers, their high cost, and the large number of tests required to establish vulnerability with confidence. Alternatively, material and component testing can be performed to quantify a model for transformer failure, and the model can be used to assess vulnerability of a wide variety of transformers. This project develops a model of the probability of equipment failure due to effects of a HEMP. Potential failure modes are cataloged, and a model structure is presented which can be quantified by the results of small-scale coupon tests.

24 POWER TRANSMISSION AND DISTRIBUTION↗