Search NASA⌕ Search

SEARCH · Search NASA

Results for “SOLAR PROGRAM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

Testing of a 10-meter Quadrant Solar Sail

The purpose of this paper is to address the technical challenges and requirements of modal testing a solar sail system (Fig. 1). Specific objectives of this work are to investigate the effectiveness (i.e. accuracy, precision, repeatability, etc.) of laser vibrometer measurements obtained on solar sail components (i.e. sail membrane quadrant and masts) actuated with various excitation methods in vacuum conditions. Results from this work will be used to determine the appropriate test technique for testing large scale full quadrant flight-like solar sail system hardware in vacuum conditions. This paper will focus on the dynamic tests conducted in-vacuum on a 10-meter solar sail quadrant development by AEC-ABLE as part of a ground demonstrator system development program funded by NASA's In-Space Propulsion program. One triangular shaped quadrant of a solar sail membrane (Fig. 2) was modal tested in a 1 Torr vacuum environment using various excitation techniques including, shaker excitation through the masts, magnetic excitation (Ref. 3), and surface-bonded piezoelectric patch actuators (Ref. 4 & 5). The excitation methods are evaluated for their applicability to in-vacuum ground testing and their traceability to the development of on-orbit flight test techniques. The solar sail masts (Fig. 3) were also tested in ambient atmospheric conditions and vacuum using various excitation techniques and these methods will also be assessed for their ground test capabilities and traceability to on-orbit flight testing.

Gaspar, James L.↗

The Potential Role of Concentrating Solar Power within the Context of DOE's 2030 Solar Cost Targets

For solar electricity generating technologies to be cost competitive at a large scale with conventionally generated electricity, cost reductions are needed for both concentrating solar power (CSP) and solar photovoltaic (PV) systems. In 2011, the U.S. Department of Energy (DOE) established solar cost targets that corresponded to reducing CSP and PV prices by approximately 75% in order to achieve a levelized cost of electricity (LCOE) of $0.06 per kilowatt-hour (kWh) for both utility-scale PV and high-capacity factor CSP-TES systems in 2020. Utility-scale PV achieved its 2020 cost target in 2017, and recent estimates for the LCOE of CSP-TES with a molten-salt power tower system are approximately $0.10/kWh for projects that are expected to come online in 2020, which represents a substantial reduction since 2010 - when the LCOE for CSP-TES was around $0.21/kWh. To continue the momentum for cost reductions in solar technologies, DOE recently established cost targets for 2030 that would make solar one of the lowest-cost sources of new electricity in the United States. For CSP-based systems, the new targets correspond to an LCOE in 2030 of $0.05/kWh for a dispatchable, high-capacity factor CSP-TES plant configuration. This aggressive target would have been unimaginable a decade ago. However, building on the previously described reduction in CSP-TES costs over the past decade, recent announcements suggest the next phase of projects will continue this downward trend through lower installation costs, attractive financing, longer-duration PPAs, and the ability to capitalize on the value that the flexibility of storage brings CSP. This presentation summarizes a recent report that evaluates the potential impacts of simultaneously achieving the 2030 cost targets for PV and CSP-TES, and it includes a detailed evaluation of the role that CSP-TES could play in realizing those impacts. The scenarios in this analysis are designed to isolate and assess the potential impacts of achieving DOE's 2030 cost targets for CSP-TES and PV, and they do not reflect the potential benefits or system impacts associated with success in other DOE research programs. The low-cost solar scenarios include DOE's 2030 solar cost targets--which are represented via a roughly 50% reduction in LCOE by 2030 (from current levels) with additional cost reductions thereafter representing technology learning and/or improvements that could result from innovation - coupled with a variety of market, technology, and demand assumptions. With these assumptions, the evolution of the contiguous U.S. electricity system is evaluated with NREL's Renewable Energy Deployment System (ReEDS) model, which was specifically designed to represent the temporal and locational value of renewable generation technologies in the U.S. power system. ReEDS relies on system-wide least-cost optimization to estimate the type and location of future generation and transmission capacity. In addition, it accounts for the locational and temporal variations in variable renewable technologies, including the need for new transmission, curtailment, dynamic capacity value, and the need to hold operating reserves to account for the uncertainty and variability of these technologies. This presentation summarizes the key findings that arise from a detailed evaluation of the impacts of achieving DOE's 2030 cost targets for CSP-TES and PV systems, noting again the inherent challenges associated with modeling future scenarios of the large, complex system electricity system in the contiguous United States within the context of various market features.

14 SOLAR ENERGY↗

LA100 Equity Strategies. Chapter 9: Equitable Community Solar Access and Benefits

The LA100 Equity Strategies project integrates community guidance with robust research, modeling, and analysis to identify strategy options that can increase equitable outcomes in Los Angeles' clean energy transition. This chapter focuses on community solar as a means to provide equitable access to local solar and storage benefits in Los Angeles. Specifically, NREL identified potential community solar sites that could host 30 kilowatts (kW)1 of solar or more and evaluated economic and equity metrics under various program design options. Analysis included a Baseline scenario (business-as-usual) and an Equity scenario, which modeled program enhancements to increase access and benefits to low-income customers. Both scenarios modeled the economics of solar and storage under the LADWP Feed-in Tariff (FiT) program (LADWP 2023b) and the LADWP Feed-in-Tariff Plus Pilot program (LADWP 2023d) compared to a community solar financial model. This research was guided by input from the community engagement process, and associated equity strategies are presented in alignment with that guidance.

14 SOLAR ENERGY↗

Reaching Grid Parity Using BP Solar Crystalline Silicon Technology: A Systems Class Application

The primary target market for this program was the residential and commercial PV markets, drawing on BP Solar's premium product and service offerings, brand and marketing strength, and unique routes to market. These two markets were chosen because: (1) in 2005 they represented more than 50% of the overall US PV market; (2) they are the two markets that will likely meet grid parity first; and (3) they are the two market segments in which product development can lead to the added value necessary to generate market growth before reaching grid parity. Federal investment in this program resulted in substantial progress toward the DOE TPP target, providing significant advancements in the following areas: (1) Lower component costs particularly the modules and inverters. (2) Increased availability and lower cost of silicon feedstock. (3) Product specifically developed for residential and commercial applications. (4) Reducing the cost of installation through optimization of the products. (5) Increased value of electricity in mid-term to drive volume increases, via the green grid technology. (6) Large scale manufacture of PV products in the US, generating increased US employment in manufacturing and installation. To achieve these goals BP Solar assembled a team that included suppliers of critical materials, automated equipment developers/manufacturers, inverter and other BOS manufacturers, a utility company, and University research groups. The program addressed all aspects of the crystalline silicon PV business from raw materials (particularly silicon feedstock) through installation of the system on the customers site. By involving the material and equipment vendors, we ensured that supplies of silicon feedstock and other PV specific materials like encapsulation materials (EVA and cover glass) will be available in the quantities required to meet the DOE goals of 5 to 10 GW of installed US PV by 2015 and at the prices necessary for PV systems to reach grid parity in 2015. This final technical report highlights the accomplishments of the BP Solar technical team from 2006 to the end of the project in February 2010. All the main contributors and team members are recognized for this accomplishment and their endeavors are recorded in the twelve main tasks described here.

14 SOLAR ENERGY↗

DOE SEEDS Program

Forecasting and influencing technological progress in solar energy: A new theory looks at an entire technological ecosystem, and understands a given technology in the context of its position within the entire technological ecosystem. Research has shown a major source of improvements in photovoltaics in recent years was improvements in its component technologies. Our research demonstrates that inputs are the primary driver of progress, and not just for solar, improvements in any given component technology is passed through to all the technologies for which that component is an input, and this process is iterated indefinitely. Such iterative processes enable us to classify technologies into trophic levels, analogous to food webs in ecology, based on their distance from natural resources. This theory predicts that technologies higher up in the technology food chain make progress faster than those below, due to the fact that they benefit from all the improvements in the all component technologies below them, technologies such as computers or photovoltaics. This at least partially explains why some technologies make more rapid progress than others.

14 SOLAR ENERGY↗

Low cost silicon solar array project silicon materials task

A program was established to develop a high temperature silicon production process using existing electric arc heater technology. Silicon tetrachloride and a reductant will be injected into an arc heated mixture of hydrogen and argon. Under these high temperature conditions, a very rapid reaction is expected to occur and proceed essentially to completion, yielding silicon and gaseous sodium chloride. Techniques for high temperature separation and collection of the molten silicon will be developed using standard engineering approaches, and the salt vapor will later be electrolytically separated into its elemental constituents for recycle. Preliminary technical evaluations and economic projections indicate not only that this process appears to be feasible, but that it also has the advantages of rapid, high capacity production of good quality molten silicon at a nominal cost.

Source record↗

Low Angle Silicon Sheet Growth. Large Area Silicon Sheet Task Low Cost Solar Array Project

The results of a program to demonstrate the feasibility of a low angle silicon ribbon growth process are described. Twenty-six experimental runs were performed. Ribbons were grown at pull rates from 5 to 68 cm/min. Ribbon lengths up to 74 cm were grown while widths varied from 5 to 25 mm. Thicknesses varied from 0.6 to 2.5 mm, with typical values of about 1 mm.

Source record↗

Theoretical studies of solar lasers and converters

A second computer program was developed for the simulation of an n - C3F7I iodine laser. The computer program is given in Appendix A and a typical output from the computer program is illustrated in Appendix B.

Heinbockel, John H.↗

The role of radiation hard solar cells in minimizing the costs of global satellite communications systems

An analysis embodied in a PC computer program is presented which quantitatively demonstrates how the availability of radiation hard solar cells can minimize the cost of a global satellite communication system. The chief distinction between the currently proposed systems, such as Iridium Odyssey and Ellipsat, is the number of satellites employed and their operating altitudes. Analysis of the major costs associated with implementing these systems shows that operation within the earth's radiation belts can reduce the total system cost by as much as a factor of two, so long as radiation hard components including solar cells, can be used. A detailed evaluation of several types of planar solar cells is given, including commercially available Si and GaAs/Ge cells, and InP/Si cells which are under development. The computer program calculates the end of life (EOL) power density of solar arrays taking into account the cell geometry, coverglass thickness, support frame, electrical interconnects, etc. The EOL power density can be determined for any altitude from low earth orbit (LEO) to geosynchronous (GEO) and for equatorial to polar planes of inclination. The mission duration can be varied over the entire range planned for the proposed satellite systems. An algorithm is included in the program for determining the degradation of cell efficiency for different cell technologies due to proton and electron irradiation. The program can be used to determine the optimum configuration for any cell technology for a particular orbit and for a specified mission life. Several examples of applying the program are presented, in which it is shown that the EOL power density of different technologies can vary by an order of magnitude for certain missions. Therefore, although a relatively radiation soft technology can be made to provide the required EOL power by simply increasing the size of the array, the impact on the total system budget could be unacceptable, due to increased launch and hardware costs. In aggregate these factors can account for more than a 10% increase in the total system cost. Since the estimated total costs of proposed global coverage systems range from $1 Billion to $9 Billion, the availability of radiation hard solar cells could make a decisive difference in the selection of a particular constellation architecture.

Summers, Geoffrey P.↗

An MHD study of the interaction between the solar wind and the interstellar medium

The overall objective of this research program is to obtain a better understanding of the interaction between the solar wind and the interstellar medium through the use of numerical solutions of the time-dependent magnetohydrodynamic (MHD) equations. The simulated results will be compared with observations where possible and with the results from previous analytic and numerical studies. The primary progress during the first two years has been to develop codes for 2-D models in both spherical and cylindrical coordinates and to apply them to the solar wind-interstellar medium interaction. Computations have been carried out for both a relatively simple gas-dynamic interaction and a flow-aligned interstellar magnetic field. The results have been shown to compare favorably with models that use more approximations and to modify and extend the previous results as would be expected. Work has also been initiated on the development of a 3-D MHD code in spherical coordinates.

Steinolfson, R. S.↗

An MHD Study of the Interaction Between the Solar Wind and the Interstellar Medium

The overall objective of this research program is to obtain a better understanding of the interaction between the solar wind and the interstellar medium through the use of numerical solutions of the time-dependent magnetohydrodynamic (MHD) equations. The simulated results have been compared with observations where possible and with the results from previous analytic and numerical studies. The primary accomplishment of this project has been the development of codes for 2-D models in both spherical and cylindrical coordinates and the application of the codes to the solar wind/interstellar medium interaction. Computations have been carried out for both a relatively simple gas-dynamic interaction and a flow-aligned interstellar magnetic field. The results have been shown to compare favorably with models that use more approximations and to modify and extend the previous results as would be expected. The simulations have also been used along with a data analysis study to provide a quantitative estimate of the distance to the termination and bow shocks. Some of the specific topics that have been studied are: (1) gas dynamic models of the solar wind/interstellar medium interaction, (2) termination shock response to large-scale solar wind fluctuations, and (3) distances to the termination shock and heliopause. The main results from each of these studies are summarized. The results were published in three papers which are included as attachments.

Steinolfson, R. S.↗

High-Temperature Solar Cell Development

The vast majority of satellites and near-earth probes developed to date have relied upon photovoltaic power generation. If future missions to probe environments close to the sun will be able to use photovoltaic power, solar cells that can function at high temperatures, under high light intensity, and high radiation conditions must be developed. For example, the equilibrium temperature of a Mercury surface station will be about 450 C, and the temperature of solar arrays on the proposed "Solar Probe" mission will extend to temperatures as high as 2000 C (although it is likely that the craft will operate on stored power rather than solar energy during the closest approach to the sun). Advanced thermal design principles, such as replacing some of the solar array area with reflectors, off-pointing, and designing the cells to reflect rather than absorb light out of the band of peak response, can reduce these operating temperature somewhat. Nevertheless, it is desirable to develop approaches to high-temperature solar cell design that can operate under temperature extremes far greater than today's cells. Solar cells made from wide bandgap (WBG) compound semiconductors are an obvious choice for such an application. In order to aid in the experimental development of such solar cells, we have initiated a program studying the theoretical and experimental photovoltaic performance of wide bandgap materials. In particular, we have been investigating the use of GaP, SiC, and GaN materials for space solar cells. We will present theoretical results on the limitations on current cell technologies and the photovoltaic performance of these wide-bandgap solar cells in a variety of space conditions. We will also give an overview of some of NASA's cell developmental efforts in this area and discuss possible future mission applications.

Landis, Geoffrey A.↗

The engineering analysis of solar radiation

A necessary precursor to construction of well-designed, efficient, and economically viable solar energy systems is the engineering analysis not only of the systems themselves but also of the solar radiation that will drive them. This paper presents the first steps in such an analysis to support the design of solar thermal power systems. A rationale for development of an integrated approach to this analysis is outlined, and elements of the approach are described. A dynamic computer simulation of a conceptual system was employed in an initial sensitivity analysis to explore how performance estimates might be affected by the precision and amount of detail in solar radiation data used as model input. A measurement program, including instrumentation, used to characterize precisely and in detail the solar resource at one location is described as is a probabilistic model derived from it, for predicting insolation as a function of time.

Reid, M. S.↗

Banking on Solar: An Analysis of Banking Opportunities in the U.S. Distributed Photovoltaic Market

This report provides a high-level overview of the developing U.S. solar loan product landscape, from both a market and economic perspective. It covers current and potential U.S. solar lending institutions; currently available loan products; loan program structures and post-loan origination options; risks and uncertainties of the solar asset class as it pertains to lenders; and an economic analysis comparing loan products to third party-financed systems in California.

14 SOLAR ENERGY↗

Determination of the Cosmic Radio Background from the Radio-Infrared Relation in Galaxies

We use the radioactive flux correlation for star forming galaxies in the local universe to derive their contribution to the cosmic radio background (CRB). The CRB from these galaxies is therefore determined by the evolution of the comoving infrared luminosity density with redshift, which is constrained by galaxy number counts at various infrared wavelengths and by the cosmic infrared background. The research of ED was supported by NASA NRA 99-OSS-01 Astrophysics Theory Program. MB acknowledges the support of the "Research Opportunities for Undergraduates in the Laboratory for Astronomy and Solar Physics" for the summer student internship program at NASA/GSFC.

Dwek, Eli↗