Search NASA⌕ Search

SEARCH · Search NASA

Results for “Surface sampling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

Hard X-ray mirrors for Nuclear Security

Research performed under this LDRD aimed to demonstrate the ability to detect and measure hard X-ray emissions using multilayer X-ray reflective optics above 400 keV, to enable the development of inexpensive and high-accuracy mirror substrates, and to investigate applications of hard X-ray mirrors of interest to the nuclear security community. Experiments conducted at the European Synchrotron Radiation Facility demonstrated hard X-ray mirror reflectivity up to 650 keV for the first time. Hard X-ray optics substrates must have surface roughness under 3 to 4 Angstrom rms, and three materials were evaluated as potential substrates: polycarbonates, thin Schott glass and a new type of flexible glass called Willow Glass®. Chemical smoothing and thermal heating of the surface of polycarbonate samples, which are inexpensive but have poor intrinsic surface characteristics, did not yield acceptable surface roughness. D263 Schott glass was used for the focusing optics of the NASA NuSTAR telescope. The required specialized hardware and process were costly and motivated experiments with a modified non-contact slumping technique. The surface roughness of the glass was preserved and the process yielded cylindrical shells with good net shape pointing to the potential advantage of this technique. Finally, measured surface roughness of 200 and 130 μm thick Willow Glass sheets was between 2 and 2.5 A rms. Additional results of flexibility tests and multilayer deposition campaigns indicated it is a promising substrate for hard X-ray optics. The detection of U and Pu characteristics X-ray lines and gamma emission lines in a high background environment was identified as an area for which X-ray mirrors could have an impact and where focusing optics could help reduce signal to noise ratio by focusing signal onto a smaller detector. Hence the first one twelvetant of a Wolter I focusing optics for the 90 to 140 keV energy range based on aperiodic multilayer coating was designed. Finally, we conducted the first demonstration that reflective multilayer mirrors could be used as diagnostic for HED experiment with an order of magnitude improvement in signal-to-noise ratio for the multilayer optic compared a transmission crystal spectrometer.

36 MATERIALS SCIENCE↗

Hanford Site Environmental Surveillance Master Sampling Schedule for Calendar Year 2009

Environmental surveillance of the Hanford Site and surrounding areas is conducted by the Pacific Northwest National Laboratory for the U.S. Department of Energy. Sampling is conducted to evaluate levels of radioactive and nonradioactive pollutants in the Hanford environs, as required in DOE Order 450.1 and DOE Order 5400.5. This document contains the calendar year 2009 schedule for the routine collection of samples for the Surface Environmental Surveillance Project and Drinking Water Monitoring Project. Each section includes sampling locations, sampling frequencies, sample types, and analyses to be performed. In some cases, samples are scheduled on a rotating basis. If a sample will not be collected in 2009, the anticipated year for collection is provided. Maps showing approximate sampling locations are included for media scheduled for collection in 2009.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Conductivity of materials made of aluminum nitride and silicon nitride mixtures

To establish the possible mechanism for conductivity in aluminum nitride a study was made of the electric conductivity of pure AlN and its mixtures with silicon nitride at different temperatures and partial pressures of nitrogen in the gas phase. The thermoelectromotive force was also measured. The experiments used polycrystalline samples of cylindrical shape 18 mm in diameter made of powders by hot pressing in graphite press molds at a temperature of 1973-2273 K and pressure 1,470,000 n/sqm. The items obtained by this method had porosity not over 5%. After pressing, the samples were machined to remove carbon from the surface, and were annealed in a stream of dry ammonia for 10 h at a temperature of 1273-1373 K. Electric conductivity was measured according to the bridge scheme on an alternating current of frequency 10 kHz. In order to guarantee close contact of the platinum electrodes with the surface of the samples, a thin layer of platinum was sprayed on them. Experiments were conducted in the temperature interval 1273-1573 K with a half hour delay at each assigned temperature with heating and cooling.

Gorbatov, A. G.↗

Sub-ppb Oxygen Contaminant Detection in Semi-Conductor Processing

Gaseous contaminants such as oxygen, water vapor, nitrogen and hydrocarbons are often present in the processing environment in semiconductor device fabrication and in containerless materials processing. The contaminants arise as a result of outgassing from hot surfaces or they may be part of the impurities in commercial ultra-high purity gases. Among these gaseous contaminants, oxygen is the most reactive and, therefore, has the most adverse effects on the end product. There has been an intense effort at the Jet Propulsion Laboratory to develop different types of oxygen sorbents to reduce oxygen concentration in a microgravity processing environment to sub-ppb (parts-per-billion) levels. Higher concentrations can lead to rapid surface oxide formation, hence reducing the quality of semiconductor devices. If the concentration of oxygen in a processing chamber at 1000oC is in the ppb level, it will only take approximately 10 seconds for an oxide layer to form on the surface of a sample. The interaction of oxygen with the water surface can lead to the formation of localized defects in semi-conductor devices, hence decreasing the manufacturing yield. For example, efficient production of 64 Mb RAM chips requires contaminations below ppb levels. This paper describes a technique for measuring trace quantities of oxygen contaminants by recording the monoatomic negative ions, O-, using mass spectrometry. The O- formation from the e--O2 interaction utilizes the electron dissociative attachment method that is greatly enhanced at the resonant energy (6.8 eV). The device combines a small gridded electron ionizer with a compact mass spectrometer. The concentrations of oxygen have been measured using the method of standard additions by diluting O2 in N2. The lowest detection limit obtained was 1.2 kHz (O- count rate) at a concentration of 10-10, corresponding to 0.1 ppb.

Sub-ppb Contaminant↗

Electrostatic Discharge Testing of Carbon Composite Solar Array Panels for the Europa Mission to Jupiter

Carbon composite solar array panel coupons similar to those considered for use on the planned NASA Europa Mission were exposed to energetic electrons to observe the size and rate of electrostatic discharge production. The discharge size and rate were found to be primarily dependent on the quantity of dielectric binder pooled on the surface of the sample. Cooling the samples to cryogenic temperatures increased the size of discharges but an end of mission radiation dose had only minimal effects. Samples were composed of M55J carbon composite impregnated with an RS3 binder. Additional samples tested included a co-cured Kapton surface.

Green, Nelson W.↗

Guidance Enhancements and Performance Assessments for the Mars Ascent Vehicle Spin-Stabilized Upper Stage Configuration

he objective of the Mars Sample Return (MSR) campaign is to return samples from the surface of Mars to Earth for research. As one element of the MSR campaign, the Mars Ascent Vehicle (MAV) is responsible for transporting the samples from the surface of Mars to a Low-Martian Orbit (LMO) for retrieval. Complete autonomy is required throughout ascent, and orbital insertion is constrained by tight dispersion boundaries. An unguided, spin-stabilized second stage for MAV has been selected over a guided upper-stage to drive mass savings and reduce overall MSR campaign mass risk, at the cost of reduced GNC capability. To address this design change, the MAV GNC team has derived a robust prediction algorithm, building on previous energy management schemes, that solves for a single inertial pointing direction solution for the spin-stabilized 2nd stage burn. Algorithm stability is explored that compared to previous versions of the algorithm. Also, a set of analytical partials was developed to study MAV’s dispersed orbital insertion performance with respect to MAV system uncertainties. These partials were verified through simulation analysis and prove useful for analytical insight into the dynamics of MAV during the 2nd stage maneuver.

Jason M Everett↗

Guidance Enhancements and Performance Assessments for the Mars Ascent Vehicle Spin-Stabilized Upper Stage Configuration

The objective of the Mars Sample Return (MSR) campaign is to return samples from the surface of Mars to Earth for research. As one element of the MSR campaign, the Mars Ascent Vehicle (MAV) is responsible for transporting the samples from the surface of Mars to a Low-Martian Orbit (LMO) for retrieval. Complete autonomy is required throughout ascent, and orbital insertion is constrained by tight dispersion boundaries. An unguided, spin-stabilized second stage for MAV has been selected over a guided upper-stage to drive mass savings and reduce overall MSR campaign mass risk, at the cost of reduced GNC capability. To address this design change, the MAV GNC team has derived a robust prediction algorithm, building on previous energy management schemes, that solves for a single inertial pointing direction solution for the spin-stabilized 2nd stage burn. Algorithm stability is explored that compared to previous versions of the algorithm. Also, a set of analytical partials was developed to study MAV’s dispersed orbital insertion performance with respect to MAV system uncertainties. These partials were verified through simulation analysis and prove useful for analytical insight into the dynamics of MAV during the 2nd stage maneuver.

GNC↗

Strain Measurement of Geological Samples Subjected to Triaxial Stresses Experienced During Hydraulic Loading

Understanding stress and strain relationships and having the ability to predict these quantities for known load conditions is crucial to all geomechanical and, in some instances, reservoir flow applications. The constitutive equations governing the deformation of geological materials are typically adequate for bulk or large scale deformation and stress analyses. However, these rules are generally less precise in their ability to make accurate predictions in physical processes where highly localized material heterogeneity exists or where the presence of geometric irregularities such as micro-cracks may be present. This is especially relevant to EGS where hydraulic fracture propagation models are needed to develop optimal reservoir creation strategies and where fracture permeability is significantly influenced by regional stress states and may affect reservoir operation strategies. The deficiencies of the models used to describe these physical processes are a practical reality necessitated by the manner in which rock properties must be obtained. Conventional rock mechanics tests subject samples to controlled load conditions and measure bulk deformations of the sample or more localized deformations only on exposed surfaces of the sample. They are currently unable to comprehensively map the deformation state within the sample. For processes such as fracture, however, the state of a particular region within the rock drives the overall failure behavior of the sample. The authors believe that possessing a means to measure strains within samples subjected to hydraulic fracture loading conditions will provide a useful tool for understanding the localized effects not captured by conventional techniques and may serve as a method for improving hydraulic fracture models. An ongoing effort at Oak Ridge National Laboratory endeavors to develop a neutron diffraction based strain measurement capability to interrogate the strain state of a geological sample, at arbitrary internal locations, subjected to a triaxial stress state. The basis of the method and initial results for simple load conditions were reported at last year s Stanford Geothermal Workshop. This work will report results from recent neutron diffraction strain measurement experiments in which marble samples were subjected to load conditions more representative of hydraulic fracturing operations within a pressure cell specially designed for the reported strain measurement technique.

An, Ke↗

2015 Long-Term Hydrologic Monitoring Program Sampling and Analysis Results at Rio Blanco, Colorado

The U.S. Department of Energy (DOE) Office of Legacy Management conducted annual sampling at the Rio Blanco, Colorado, Site for the Long-Term Hydrologic Monitoring Program (LTHMP) on May 20–21, 2015. This report documents the analytical results of the Rio Blanco annual monitoring event, the trip report, and the data validation package. The groundwater and surface water monitoring samples were shipped to the GEL Group Inc. laboratories for conventional analysis of tritium and analysis of gamma-emitting radionuclides by high-resolution gamma spectrometry. A subset of water samples collected from wells near the Rio Blanco site was also sent to GEL Group Inc. for enriched tritium analysis. All requested analyses were successfully completed. Samples were collected from a total of four onsite wells, including two that are privately owned. Samples were also collected from two additional private wells at nearby locations and from nine surface water locations. Samples were analyzed for gamma-emitting radionuclides by high-resolution gamma spectrometry, and they were analyzed for tritium using the conventional method with a detection limit on the order of 400 picocuries per liter (pCi/L). Four locations (one well and three surface locations) were analyzed using the enriched tritium method, which has a detection limit on the order of 3 pCi/L. The enriched locations included the well at the Brennan Windmill and surface locations at CER-1, CER-4, and Fawn Creek 500 feet upstream.

54 ENVIRONMENTAL SCIENCES↗

Preliminary far-field plume sputtering characterization of the Stationary Plasma Thruster (SPT-100)

For electric propulsion devices to be considered for use on communications satellites, integration impacts must be examined in detail. Two phenomena of concern associated with highly energetic plumes are contamination via sputtered material from the thruster and sputter erosion of downstream surfaces. In order to characterize the net effect of both phenomena, an array of witness plates were mounted in several types of holders and were exposed to the SPT-100 thruster plume for 50 hours. Surface analysis of the witness plates revealed that in the most energetic regions of the plume, there was a net removal of material from the samples facing the thruster. In the peripheral regions, net deposits were observed and characterized by the changes in optical properties of these samples. Changes in surface properties of samples located in collimators were within experimental uncertainty.

Pencil, Eric J.↗

Magnetization measurements and XMCD studies on ion irradiated iron oxide and core-shell iron/iron-oxide nanomaterials

Magnetite (Fe3O4) and core-shell iron/iron-oxide (Fe/Fe3O4) nanomaterials prepared by a cluster deposition system were irradiated with 5.5 MeV Si2+ ions and the structures determined by x-ray diffraction as consisting of 100% magnetite and 36/64 wt% Fe/FeO, respectively. However, x-ray magnetic circular dichroism (XMCD) indicates similar surfaces in the two samples, slightly oxidized and so having more Fe3+ than the expected magnetite structure, with XMCD intensity much lower for the irradiated core-shell samples indicating weaker magnetism. X-ray absorption spectroscopy (XAS) data lack the signature for FeO, but the irradiated core-shell system consists of Fe-cores with ~13 nm of separating oxide crystallite, so it is likely that FeO exists deeper than the probe depth of the XAS (~5 nm). Exchange bias (Hex) for both samples becomes increasingly negative as temperature is lowered, but the irradiated Fe3O4 sample shows greater sensitivity of cooling field on Hex. Loop asymmetries and Hex sensitivities of the irradiated Fe3O4 sample are due to interfaces and interactions between grains which were not present in samples before irradiation as well as surface oxidation. Asymmetries in the hysteresis curves of the irradiated core/shell sample are related to the reversal mechanism of the antiferromagnetic FeO and possibly some near surface oxidation.

core-shell, magnetite, irradiation, XMCD↗

MBSE Applications for the MSR SRC Mars Ascent Vehicle

The objective of the NASA Mars Sample Return (MSR) Campaign is to collect samples from the surface of Mars and return them to Earth for scientific research. The Mars Ascent Vehicle (MAV) will be integrated into a larger Mars Sample Retrieval Lander (SRL) for transit to and storage on Mars. After all Martian samples have been collected and loaded into the MAV payload assembly, MAV will deliver the samples from the Martian surface to Mars orbit. A separate spacecraft, the Earth Return Orbiter (ERO) will retrieve the samples from Mars orbit and return them to Earth. To address common systems engineering challenges associated with using traditional systems engineering practices on complex projects, the MAV systems engineering team has explored implementation of Model-Based Systems Engineering (MBSE) tools and languages. This paper describes the current state of implementation and development of the MAV MBSE model with the Systems Modeling Language (SysML) within the scope of the MAV Systems Requirement Cycle (SRC) systems engineering workflow. The MAV MBSE model has been developed within Magic Draw – a SysML editor commonly used to implement MBSE. The MAV MBSE model has been used to develop mission phase functional flow diagrams for the Concept of Operations, decompose mission to vehicle subsystem functions, develop a functional decomposition, derive functional requirements, trace requirements up to customer-imposed requirements, trace requirements within MAV requirement space, identify requirements trace gaps, define and map the physical design space architecture, allocate requirements to subsystems, develop validation items, define assembly, integration, and test (AI&T) operations, and trace these items across driving goals to develop an integrated digital thread of systems engineering information used to drive design specifications, decision making, and ultimately design verification and validation. Findings and results associated with implementing MBSE in these ways, alongside traditional methods will be discussed.

MBSE↗

MBSE Applications for the MSR SRC Mars Ascent Vehicle

The objective of the NASA Mars Sample Return (MSR) Campaign is to collect samples from the surface of Mars and return them to Earth for scientific research. The Mars Ascent Vehicle (MAV) will be integrated into a larger Mars Sample Retrieval Lander (SRL) for transit to and storage on Mars. After all Martian samples have been collected and loaded into the MAV payload assembly, MAV will deliver the samples from the Martian surface to Mars orbit. A separate spacecraft, the Earth Return Orbiter (ERO) will retrieve the samples from Mars orbit and return them to Earth. To address common systems engineering challenges associated with using traditional systems engineering practices on complex projects, the MAV systems engineering team has explored implementation of Model-Based Systems Engineering (MBSE) tools and languages. This paper describes the current state of implementation and development of the MAV MBSE model with the Systems Modeling Language (SysML) within the scope of the MAV Systems Requirement Cycle (SRC) systems engineering workflow. The MAV MBSE model has been developed within Magic Draw – a SysML editor commonly used to implement MBSE. The MAV MBSE model has been used to develop mission phase functional flow diagrams for the Concept of Operations, decompose mission to vehicle subsystem functions, develop a functional decomposition, derive functional requirements, trace requirements up to customer-imposed requirements, trace requirements within MAV requirement space, identify requirements trace gaps, define and map the physical design space architecture, allocate requirements to subsystems, develop validation items, define assembly, integration, and test (AI&T) operations, and trace these items across driving goals to develop an integrated digital thread of systems engineering information used to drive design specifications, decision making, and ultimately design verification and validation. Findings and results associated with implementing MBSE in these ways, alongside traditional methods will be discussed.

MBSE↗

Measurements of plasma temperature in indirect drive targets from the shock wave velocity in aluminum in the Iskra-5 facility

Results are presented from the development of a method for measuring plasma temperature in indirect (X-ray) drive targets by recording the shock wave velocity in the Iskra-5 facility. The samples under investigation were irradiated by X-rays in a converter box, and the shock wave velocity was determined from the time at which the wave reached the back surface of the sample and the surface began to emit visible radiation. This emission, in turn, was detected by a streak camera. The results of experiments on the interaction of X radiation with a hot dense plasma, as well as the accompanying gas-dynamic processes in aluminum samples, are analyzed both theoretically and numerically. In experiments with Al and Pb samples, the shock wave velocity was measured to vary in the range U = 8-35 km/s, and the range of variation of the temperature of the box walls was measured to be T{sub e} = 140-170 eV.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experimental Study and Fractal Analysis on the Anisotropic Performance of Explosively Welded Interfaces of 304 Stainless Steel/245 Carbon Steel

The mechanical anisotropy of an explosive welding composite plate made of 304 stainless steel/245 steel was studied through shear experiments performed on explosively welded wavy interfaces along several orientation angles. The results indicated that the strength and the fracture energy of samples significantly varied with the orientation angles. The fracture surfaces of all samples were observed using a scanning electron microscope and through three-dimensional structure microscopy. The periodic features of all the fracture surfaces were clearly shown in different fracture modes. The fractal dimension of the fracture surfaces was calculated based on the fractal geometry by the box-counting method in MATLAB. The cohesive element model was used to analyze the fracture energy according to the physical dependence of the fractal dimension on thermodynamic entropy and interface separation energy. The fracture energy was an exponential function of the fractal dimension value, which was in good agreement with the experimental results. All results were validated for effective use in the application of anisotropy analysis to the welded interface and structural optimization of explosively welded composite plates.

36 MATERIALS SCIENCE↗

A Novel Hybrid Ultramicrotomy/FIB-SEM Technique: Preparation of Serial Electron-Transparent Thin Sections of a Hayabusa Grain

The Japanese space agency's (JAXA) Hayabusa mission returned the first particulate samples (typically <100micron) from the surface of an asteroid (25143 Itokawa). These precious samples provide important insights into early Solar System processes, but their sizes pose tremendous challenges to coordinated analysis using a variety of nano- and micro-beam techniques. The ability to glean maximal information from individual particles has become increasingly important and depends critically on sample preparation. We developed a hybrid technique combining traditional ultramicrotomy with focused ion beam (FIB) techniques, allowing for more thorough in situ investigations of grain surfaces and interiors. Using this method, we increase the number of FIB-prepared sections that can be recovered from a particle with dimensions on the order of tens of microns. These sections can be subsequently analyzed using a variety of analytical techniques. Particle RA-QD02-0211 is a approx. 40×40×20 micron particle from Itokawa containing olivine and Fe sulfides. It was embedded in low viscosity epoxy and partly sectioned to a depth of approx 10 micron; sections are placed on Cu grids with thin amorphous films for transmission electron microscope (TEM) analyses. With the sample surface partly exposed, the epoxy bullet is trimmed to a height of approx. 5mm to accommodate the allowable dimensions for FIB work (FEI Quanta 600 3D dual beam FIB-SEM). Using a diamond trim knife, the epoxy surrounding the grain is removed on 3 sides (to within a few microns of the grain); the depth of material removed extends well below the bottom of the particle. The sample is attached to an SEM pin mount, the epoxy coated with conductive paint, and the entire assembly coated with approx. 40nm of carbon to eliminate sample charging during FIB work. A protective carbon cap is placed according to the plan for the 15 FIB sections. The central 'spine' of the cap runs perpendicular to the front of the sample, and the 'ribs' protruding from either side run parallel. Each rib indicates the location of a planned FIB section, and the spine contains the final two planned sections. We use a cap with a 4 micron-wide spine and 2micron-wide ribs that have ≳3.5 micron of space between them (narrower cuts result in too much re-deposition of material inside the trenches). Using a 30kV, 3nA ion-beam we expose the front surface of the grain and commence milling trenches between sections. Rather than using the typical C-cut to prepare the sample for lift-out, an L-cut is used instead, leaving the sample connected by an interior tab. tab. Sections are lifted out, attached to TEM grids and thinned to electron transparency. TEM analyses show that our hybrid technique preserves both interior and edge features, including surface modifications from exposure to the space environment, such as damaged rims that form in response to solar wind implantation effects and adhering grains. In addition, the FIB sections provide larger areas that are free of fractures and chatter effects in comparison to the microtome thin sections, thus enabling more accurate measurements of solar flare particle track densities that are used to determine the surface exposure age of the particles.

Berger, Eve L.↗

Instruction manual, Optical Effects Module, Model OEM

The Optical Effects Module Model OEM-1, a laboratory prototype instrument designed for the automated measurement of radiation transmission and scattering through optical samples, is described. The system comprises two main components: the Optical Effects Module Enclosure (OEME) and the Optical Effects Module Electronic Controller and Processor (OEMCP). The OEM is designed for operation in the near UV at approximately 2540A, corresponding to the most intense spectral line activated by the mercury discharge lamp used for illumination. The radiation from this source is detected in transmission and reflection through a number of selectable samples. The basic objective of this operation is to monitor in real time the accretion of possible contamination on the surface of these samples. The optical samples are exposed outside of the OEME proper to define exposure conditions and to separate exposure and measurement environments. Changes in the transmissivity of the sample are attributable to surface contamination or to bulk effects due to radiation. Surface contamination will increase radiation scattering due to Rayleigh-Gans effect or to other phenomena, depending on the characteristics size of the particulate contaminants. Thus, also scattering from the samples becomes a part of the measurement program.

Source record↗

The Small Scale Environment of Low Surface Brightness Disk Galaxies

We use a sample of ~340 low surface brightness (LSB) disk galaxies with measured redshifts in combination with the Center for Astrophysics redshift survey to test the hypothesis that LSB galaxies have a deficit of nearby companion galaxies compared to high surface brightness (HSB) disk galaxies.

surface↗