Search NASA⌕ Search

SEARCH · Search NASA

Results for “electronics analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

Structural studies of TiC{sub 1−x}O{sub x} solid solution by Rietveld refinement and first-principles calculations

The lattice parameters, structural stability and electronic structure of titanium oxycarbides (TiC{sub 1−x}O{sub x}, 0≤x≤1) solid solution were investigated by Rietveld refinement and first-principles calculations. Series of TiC{sub 1−x}O{sub x} were precisely synthesized by sintering process under the vacuum. Rietveld refinement results of XRD patterns show the properties of continuous solid solution in TiC{sub 1−x}O{sub x} over the whole composition range. The lattice parameters vary from 0.4324 nm to 0.4194 nm decreasing with increasing oxygen concentration. Results of first-principles calculations reveal that the disorder C/O structure is stable than the order C/O structure. Further investigations of the vacancy in Ti{sub 1−Va}(C{sub 1−x}O{sub x}){sub 1−Va} solid solution present that the structure of vacancy segregated in TiO-part is more stable than the disorder C/O structure, which can be ascribed to the Ti–Ti bond across O-vacancy and the charge redistributed around Ti-vacancy via the analysis of the electron density difference plots and PDOS. - Graphical abstract: XRD of series of titanium oxycarbides (TiC{sub 1−x}O{sub x}, 0≤x≤1) solid solution prepared by adjusting the proportion of TiO in the starting material. Highlights: • Titanium oxycarbides were obtained by sintering TiO and TiC under carefully controlled conditions. • Rietveld refinement results show continuous solid solution with FCC structure in TiC{sub 1−x}O{sub x}. • The disorder C/O structure is stable than the order C/O structure. • Introduction of vacancy segregated in TiO-part is more stable than disorder C/O structure. • Ti–Ti bond across O-vacancy and the charge redistributed around Ti-vacancy enhance structural stability.

36 MATERIALS SCIENCE↗

Modeling and analyzing parasitic parameters in high frequency converters

This research focuses on electromagnetic interference (EMI) / electromagnetic compatibility (EMC) design and analysis in power electronics systems. To limit the EMI under the standards, different methods and strategies are investigated. Parasitic parameters of high frequency (HF) transformer are analyzed using a novel analytical method, finite element method (FEM), and experimental measurements for different structures and windings arrangements. Also, the magnetic field, electric field, electric displacement, and electric potential distribution are simulated and analyzed. Moreover, a high voltage system is considered and analyzed to improve the EMC. The EMI propagation paths are analyzed. The EMI noise level of the system is obtained and compared to the IEC61800-3 standard. To improve the EMC, the parasitic parameters of the transformer, as the main path of EMI circulation, are analyzed and optimized to block the propagation. Furthermore, the geometry structure of the HF transformer is optimized to lower the parasitics in the system. Three pareto-optimal techniques are investigated for the optimization. The models and results are verified by 3D-FEM and experimental results for several given scenarios. Furthermore, the EMC modeling and conducted EMI analysis are developed for a system including an AC-DC-DC power supply (rectifier and dual active bridge (DAB) converter). Moreover, the common mode (CM) EMI noise propagation through the system is discussed and the noise sources and effect of components on the noise are analyzed. Additionally, the CM impedance of different parts of the system and the noise levels are discussed. Finally, EMI attenuation techniques were applied to the system.

24 POWER TRANSMISSION AND DISTRIBUTION↗

2D axial-azimuthal particle-in-cell benchmark for low-temperature partially magnetized plasmas

The increasing need to demonstrate the correctness of computer simulations has highlighted the importance of benchmarks. We define in this paper a representative simulation case to study low-temperature partially-magnetized plasmas. Seven independently developed particle-in-cell codes have simulated this benchmark case, with the same specified conditions. The characteristics of the codes used, such as implementation details or computing times and resources, are given. First, we compare at steady-state the time-averaged axial profiles of three main discharge parameters (axial electric field, ion density and electron temperature). We show that the results obtained exhibit a very good agreement within 5% between all the codes. As E x B discharges are known to cause instabilities propagating in the direction of electron drift, an analysis of these instabilities is then performed and a similar behaviour is retrieved between all the codes. A particular attention has been paid to the numerical convergence by varying the number of macroparticles per cell and we show that the chosen benchmark case displays a good convergence. Detailed outputs are given in the supplementary data, to be used by other similar codes in the perspective of code verification.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Driving Electron Transfer in Photosystem I Using Far-Red Light: Overall Perspectives

Photosystem I (PSI) is a photosynthetic protein–pigment complex that, upon photoexcitation, transfers electrons to ferredoxin, facilitating the production of NADPH. Isolated PSI reaction centers (RCs) have also been used in hybrid systems to reduce protons and produce ‘biohydrogen’. This review article examines how various cyanobacteria with similar photosynthetic machinery utilize different wavelengths of light to execute photosynthetic electron transport through PSI. Key factors, such as, the structure of the electron transfer cofactors, the protein environment surrounding the primary donor pigments and hydrogen-bonding interactions with the surrounding protein matrix are analyzed to understand their roles in maintaining efficient electron transfer when it is driven using photons of different energies. We compare PSI complexes with known atomic structures from four species of cyanobacteria, Thermosynechococcus elongatus, Acaryochloris marina, Halomicronema hongdechloris, and Fischerella thermalis. T. elongatus is typical of most oxygenic photosynthetic organisms in that it requires visible light and uses only chlorophyll a (Chl a ) in PSI. In contrast, H. hongdechloris and F. thermalis are photoacclimating species capable of producing Chl f and Chl d that use red light when little visible light is available. A. marina , on the other hand, is adapted to red light conditions and consistently utilizes Chl d as its primary photosynthetic pigment, maintaining a stable pigment composition. Here, we explore the structural and functional differences between the PSI RCs of these organisms and the impact of these differences on electron transport. The structural differences in the cofactors influence both the absorption wavelengths of the cofactors and the energy levels of the intermediate states of electron transfer. An analysis of the surrounding protein shows how it has been adapted and underscores the interplay between the pigment structure, protein environment, and hydrogen bonding networks in tuning the efficiency and adaptability of photosynthetic mechanisms across different species of cyanobacteria.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Spectroscopic investigation of the electronic and excited state properties of para-substituted tetraphenyl porphyrins and their electrochemically generated ions

Porphyrins play pivotal roles in many crucial biological processes including photosynthesis. However, there is still a knowledge gap in understanding electronic and excited state implications associated with functionalization of the porphyrin ring system. These effects can have electrochemical and spectroscopic signatures that reveal the complex nature of these somewhat minor substitutions, beyond simple inductive or electronic effect correlations. To obtain a deeper insight into the influences of porphyrin functionalization, four free-base, meso-substituted porphyrins: tetraphenyl porphyrin (TPP), tetra(4-hydroxyphenyl) porphyrin (THPP), tetra(4-carboxyphenyl) porphyrin (TCPP), and tetra(4-nitrophenyl) porphyrin (TNPP), were synthesized, characterized, and investigated. The influence of various substituents, (-hydroxy,-carboxy, and -nitro) in the para position of the meso-substituted phenyl moieties were evaluated by spectroelectrochemical techniques (absorption and fluorescence), femtosecond transient absorption spectroscopy, cyclic and differential pulse voltammetry, ultraviolet photoelectron spectroscopy (UPS), and time-dependent density functional theory (TD-DFT). Spectral features were evaluated for the neutral porphyrins and differences observed among the various porphyrins were further explained using rendered frontier molecular orbitals pertaining to the relevant transitions. Electrochemically generated anionic and cationic porphyrin species indicate similar absorbance spectroscopic signatures attributed to a red-shift in the Soret band. Emissive behavior reveals the emergence of one new fluorescence decay pathway for the ionic porphyrin, distinct from the neutral macrocycle. Femtosecond transient absorption spectroscopy analysis provided further analysis of the implications on the excited-state as a function of the para substituent of the free-base meso-substituted tetraphenyl porphyrins. Herein, we provide an in-depth and comprehensive analysis of the electronic and excited state effects associated with systematically varying the induced dipole at the methine bridge of the free-base porphyrin macrocycle and the spectroscopic signatures related to the neutral, anionic, and cationic species of these porphyrins.

59 BASIC BIOLOGICAL SCIENCES↗

Designing linear lattices for round beam in electron storage rings using the solution by linear matrices analysis

For some synchrotron light source beamline applications, a round beam is preferable to a flat one. A conventional method of obtaining round beam in an electron storage ring is to shift its tune close to a linear difference resonance. The linearly coupled beam dynamics is analyzed with perturbation theories, which have certain limitations. In this paper, we adopt the Solution by LInear Matrices (SLIM) analysis to calculate exact beam sizes to design round beam lattices. The SLIM analysis can deal with a generally linearly coupled accelerator lattice. The effects of various coupling sources on beam emittances and sizes can be studied within a self-consistent frame. Both the on- and off-resonance schemes to obtain round beams are explained with examples. The SLIM formalism for two widely used magnet models: combined-function bending magnets, and planar wigglers and undulators, is also derived.

43 PARTICLE ACCELERATORS↗

Mechanism of power consumption inhibitive multi-layer Zn:SiO{sub 2}/SiO{sub 2} structure resistance random access memory

In this paper, multi-layer Zn:SiO{sub 2}/SiO{sub 2} structure is introduced to reduce the operation power consumption of resistive random access memory (RRAM) device by modifying the filament formation process. And the configuration of multi-layer Zn:SiO{sub 2}/SiO{sub 2} structure is confirmed and demonstrated by auger electron spectrum. Material analysis together with conduction current fitting is applied to qualitatively evaluate the carrier conduction mechanism on both low resistance state and high resistance state. Finally, single layer and multilayer conduction models are proposed, respectively, to clarify the corresponding conduction characteristics of two types of RRAM devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Chemical and structural investigation of the role of both Mn and Mn oxide in the formation of manganese silicate barrier layers on SiO{sub 2}

In this study, Mn silicate (MnSiO{sub 3}) barrier layers were formed on thermally grown SiO{sub 2} using both metallic Mn and oxidized Mn films, in order to investigate the role of oxygen in determining the extent of the interaction between the deposited Mn and the SiO{sub 2} substrate. Using x-ray photoelectron spectroscopy, it has been shown that a metallic Mn film with an approximate thickness of 1 nm cannot be fully converted to Mn silicate following vacuum annealing to 500 deg. C. Transmission electron microscopy (TEM) analysis suggests the maximum MnSiO{sub 3} layer thickness obtainable using metallic Mn is {approx}1.7 nm. In contrast, a {approx}1 nm partially oxidized Mn film can be fully converted to Mn silicate following thermal annealing to 400 deg. C, forming a MnSiO{sub 3} layer with a measured thickness of 2.6 nm. TEM analysis also clearly shows that MnSiO{sub 3} growth results in a corresponding reduction in the SiO{sub 2} layer thickness. It has also been shown that a fully oxidized Mn oxide thin film can be converted to Mn silicate, in the absence of metallic Mn. Based on these results it is suggested that the presence of Mn oxide species at the Mn/SiO{sub 2} interface facilitates the conversion of SiO{sub 2} to MnSiO{sub 3}, in agreement with previously published studies.

36 MATERIALS SCIENCE↗

Enhanced photon collection of high surface area carbonate-doped mesoporous TiO2 nanospheres in dye sensitized solar cells

Highlights: • Carbonate-doped mesoporous TiO{sub 2} showed enhanced DSSC efficiency (5.4%). • Carbonate-doped TiO{sub 2} indicated higher surface area and incident photon conversion efficiency. • Carbonate-doped TiO{sub 2} showed lower resistance and longer life time. - Abstract: Carbonate-doped mesoporous TiO{sub 2} nanospheres with anatase phase were successfully synthesized by the simple solvothermal method. The synthesized nanospheres were monodispersed and composed of particles having the size of 10–15 nm. Scanning transmission electron microscopy (STEM) analysis showed nanosphere with large number particles. STEM-mapping clearly showed that Ti, O, and C were homogeneously distributed. Incorporation of carbonate in TiO{sub 2} was confirmed by XPS analysis. The peak at 284.3 eV was assigned to CO and indicated the formation TiOC structure due to carbonate doping in TiO{sub 2} lattice. Dye-sensitized solar cells (DSSCs) containing the nanospheres were fabricated by spray coating technique using N719 dye. Carbonate-doped mesoporous TiO{sub 2} showed enhanced DSSC efficiency (5.4%) compared to undoped (3.4%) and commercially available TiO{sub 2} (P25) (2.4%). It indicated (1) higher surface area and incident photon conversion efficiency, (2) lower resistance and longer life time compared with undoped TiO{sub 2}.

14 SOLAR ENERGY↗

Tensile and compressive creep behavior of extruded Mg–10Gd–3Y–0.5Zr (wt.%) alloy

The tensile and compressive creep behavior of an extruded Mg–10Gd–3Y–0.5Zr (wt.%) alloy was investigated at temperatures ranging from 200 °C to 300 °C and under stresses ranging from 30 MPa to 120 MPa. There existed an asymmetry in the tensile and compressive creep properties. The minimum creep rate of the alloy was slightly greater in tension than in compression. The measured values of the transient strain and initial creep rate in compression were greater than those in tension. The creep stress exponent was approximately 2.5 at low temperatures (T < 250 °C) and 3.4 at higher temperatures both in tension and in compression. The compression creep activation energy at low temperatures and high temperatures was 83.4 and 184.3 kJ/mol respectively, while one activation energy (184 kJ/mol) represented the tensile–creep behavior over the temperature range examined. Dislocation creep was suggested to be the main mechanism in tensile creep and in the high-temperature regime in compressive creep, while grain boundary sliding was suggested to dominate in the low-temperature regime in compressive creep. Precipitate free zones were observed near grain boundaries perpendicular to the loading direction in tension and parallel to the loading direction in compression. Electron backscattered diffraction analysis revealed that the texture changed slightly during creep. Non-basal slip was suggested to contribute to the deformation after basal slip was introduced. In the tensile–creep ruptured specimens, intergranular cracks were mainly observed at general high-angle boundaries. - Highlights: • Creep behavior of an extruded Mg–RE alloy was characterized by EBSD. • T5 aging treatment enhanced the tension–compression creep asymmetry. • The grains grew slightly during tensile creep, but not for compressive creep. • Precipitate free zones (PFZs) were observed at specific grain boundaries. • Intergranular fracture was dominant and cracks mainly originated at GHABs.

36 MATERIALS SCIENCE↗

Energy transfer kinetics in oxy-fluoride glass and glass-ceramics doped with rare-earth ions

An investigation of donor-acceptor energy transfer kinetics in dual rare earths doped precursor oxy-fluoride glass and its glass-ceramics containing NaYF{sub 4} nano-crystals is reported here, using three different donor-acceptor ion combinations such as Nd-Yb, Yb-Dy, and Nd-Dy. The precipitation of NaYF{sub 4} nano-crystals in host glass matrix under controlled post heat treatment of precursor oxy-fluoride glasses has been confirmed from XRD, FESEM, and transmission electron microscope (TEM) analysis. Further, the incorporation of dopant ions inside fluoride nano-crystals has been established through optical absorption and TEM-EDX analysis. The noticed decreasing trend in donor to acceptor energy transfer efficiency from precursor glass to glass-ceramics in all three combinations have been explained based on the structural rearrangements that occurred during the heat treatment process. The reduced coupling phonon energy for the dopant ions due to fluoride environment and its influence on the overall phonon assisted contribution in energy transfer process has been illustrated. Additionally, realization of a correlated distribution of dopant ions causing clustering inside nano-crystals has also been reported.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Pack-boriding of Fe-Mn binary alloys: Characterization and kinetics of the boride layers

In this work, the boronizing of Fe-Mn binary alloys at 0.42, 0.76 and 0.94 wt.% Mn was carried out in a solid medium using the powder pack method. In this method, commercial Ekabor-II boron source and activator (ferro-silicon) were thoroughly mixed to form the boriding medium. The samples were boronized in an electrical resistance furnace for exposure times of 2, 4, 6 and 8 h at 1173 K under atmospheric pressure and a series of boronized samples in the temperature range 1073-1373 K for 3 h. After the furnace process, boronized samples were removed from the furnace and cooled in air. Afterwards, the boride layers generated by the pack-boronizing process were characterized by optical microscopy, scanning electron microscopy, XRD analysis, Vickers microhardness and tensile testing. The generated boride layers, showing a saw-tooth morphology, had a surface microhardness in the range 1400-1270 HV0.1. It was shown that the values of yield stresses and ultimate tensile stresses were increased as the Mn content increases in the boronized Fe-Mn binary alloys. In contrast, the values of elongations determined from the stress-strain curves were decreased. Furthermore, it was found that the calculated mean value of the activation energy of boron diffusion was close to 119 J/mol.

36 MATERIALS SCIENCE↗

Combustion synthesis and luminescence properties of yellow-emitting phosphors Ca{sub 2}BO{sub 3}Cl:Eu{sup 2+}

Graphical abstract: A yellow-emitting phosphor Ca{sub 2}BO{sub 3}Cl:Eu{sup 2+} was firstly synthesized by the solution-combustion method. The photoluminescence excitation and emission spectra, temperature dependence of luminescence intensity, and luminescence lifetime of the phosphor were investigated. Highlights: Black-Right-Pointing-Pointer Ca{sub 2}BO{sub 3}Cl:Eu{sup 2+} phosphor was synthesized by a solution-combustion method. Black-Right-Pointing-Pointer Ca{sub 2}BO{sub 3}Cl:Eu{sup 2+} showed an intense yellow emission band centered at 569 nm with the CIE coordinate of (0.453, 0.526). Black-Right-Pointing-Pointer The temperature dependent luminescence property and mechanism of Ca{sub 2}BO{sub 3}Cl:Eu{sup 2+} were studied. -- Abstract: Yellow-emitting phosphor Ca{sub 2}BO{sub 3}Cl:Eu{sup 2+} was synthesized by a solution-combustion method. The phase structure and microstructure were determined by the X-ray diffraction (XRD) and scanning electron microscope (SEM) analysis, respectively. The as-prepared Ca{sub 2}BO{sub 3}Cl:Eu{sup 2+} phosphor absorbed near ultraviolet and blue light of 320-500 nm, and showed an intense yellow emission band centered at 569 nm with the CIE coordinate of (0.453, 0.526). The lifetime of Eu{sup 2+} ions in Ca{sub 2}BO{sub 3}Cl:Eu{sup 2+} phosphor was measured, furthermore the temperature dependent luminescence property and mechanism were studied, which also testified that the present phosphor had a promising potential for white light-emitting diodes.

36 MATERIALS SCIENCE↗

Physical characterization of uranium oxide pellets and powder applied in the Nuclear Forensics International Technical Working Group Collaborative Materials Exercise 4

Physical characterization is one of the most broad and important categories of techniques to apply in a nuclear forensic examination. Physical characterization techniques vary from simple weighing and dimensional measurements to complex sample preparation and scanning electron microscopy-electron backscatter diffraction analysis. This paper reports on the physical characterization conducted by several international laboratories participating in the fourth Collaborative Materials Exercise, organized by the Nuclear Forensics International Technical Working Group. Methods include a range of physical measurements, microscopy-based observations, and profilometry. In conclusion, the value of these results for addressing key investigative questions concerning two uranium dioxide pellets and a uranium dioxide powder is discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Deltamethrin induced RIPK3-mediated caspase-independent non-apoptotic cell death in rat primary hepatocytes

Deltamethrin (DLM), a synthetic pyrethroid insecticide, is used all over the world for indoor and field pest management. In the present study, we investigated the elicited pathogenesis of DLM-induced hepatotoxicity in rat primary hepatocytes. DLM-induced cell death was accompanied with increased ROS generation, decreased mitochondrial membrane potential and G2/M arrest. Pre-treatment with N-acetyl cysteine/butylated hydroxyanisole/IM54 could partly rescue hepatocytes suggesting that ROS might play a role in DLM-induced toxicity. Interestingly, DLM treatment resulted in a caspase-independent but non-apoptotic cell death. Pre-treatment with pan-caspase inhibitor (ZVAD-FMK) could not rescue hepatocytes. Unaltered caspase-3 activity and absence of cleaved caspase-3 also corroborated our findings. Further, LDH release and Transmission electron microscopy (TEM) analysis demonstrated that DLM incites membrane disintegrity and necrotic damage. Immunochemical staining revealed an increased expression of inflammatory markers (TNFα, NFκB, iNOS, COX-2) following DLM treatment. Moreover, the enhanced RIPK3 expression in DLM treated groups and prominent rescue from cell death by GSK-872 indicated that DLM exposure could induce programmed necrosis in hepatocytes. The present study demonstrates that DLM could induce hepatotoxicity via non-apoptotic mode of cell death. - Highlights: • Deltamethrin (DLM) induces caspase-independent death in rat primary hepatocytes. • RIPK3 played a central role in DLM-mediated programmed necrosis in liver cells. • Reactive oxygen species played a role in DLM mediated hepatotoxity.

60 APPLIED LIFE SCIENCES↗

First-principles study of atomic and electronic structures of 60° perfect and 30°/90° partial glide dislocations in CdTe

The atomic and electronic structures of 60° glide perfect and 30°/90° glide partial dislocations in CdTe are studied using combined semi-empirical and density functional theory calculations. The calculations predict that the dislocation cores tend to undergo significant reconstructions along the dislocation lines from the singly-periodic (SP) structures, yielding either doubly-periodic (DP) ordering by forming a dimer or quadruply-periodic (QP) ordering by alternating a dimer and a missing dimer. Charge modulation along the dislocation line, accompanied by the QP reconstruction for the Cd-/Te-core 60° perfect and 30° partials or the DP reconstruction for the Cd-core 90° partial, results in semiconducting character, as opposed to the metallic character of the SP dislocation cores. Dislocation-induced defect states for the 60° Cd-/Te-core are located relatively close to the band edges, whereas the defect states lie in the middle of the band gap for the 30° Cd-/Te-core partial dislocations. In addition to the intracore charge modulation within each QP core, the possibility of intercore charge transfer between two different dislocation cores when they are paired together in the same system is discussed. As a result, the analysis of the electronic structures reveals the potential role of the dislocations on charge transport in CdTe, particularly in terms of charge trapping and recombination.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Accumulative fold-forging (AFF) as a novel severe plastic deformation process to fabricate a high strength ultra-fine grained layered aluminum alloy structure

Highlights: • A novel SPD process named as AFF was introduced. • AFF process is based on the repetitive forging of folded metal foils. • This new method possesses an exceptional capability for fabrication of UFG layered structures. • An AA8006 aluminum alloy layered material with the UFG structure of 200–300 nm was produced. • An enhanced hardness up to ~ 100% was attained owing to the UFG and layered structures. - Abstract: A novel severe plastic deformation (SPD) process termed accumulative fold forging (AFF) is introduced to fabricate a homogenous ultra-fine grained (UFG) layered metal structure by repetitive folding and forging aluminum alloy foil. The present work studies AFF applied to thin foils of AA8006 Al-Fe-Mn aluminum alloy after 26 folding steps to produce a UFG structure containing 67,108,864 layers across a 2 mm thickness. The structure of the layers and grain refinement are studied using X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM) and scanning-transmission electron microscopy (STEM) analysis. The results indicate a well-bonded inter-layer structure with an average grain size of about 200 nm parallel and 250 nm perpendicular to the forging direction, while dislocation density increased to ~ 7.2 × 10{sup 15} m{sup − 2} following AFF. The mechanical strength of the aluminum foil is evaluated in the terms of indentation hardness testing before and after AFF process. The processed UFGed layered material exhibited an average hardness value of ~ 61.5 Vickers as compared to the initial value of ~ 30.4 Vickers for the annealed foil alloy, which indicates an improvement of ~ 100% due to the contributions of grain refinement, work hardening and interfacial strengthening of the bonded layers.

36 MATERIALS SCIENCE↗

Synthesis, dielectric behavior and impedance measurement studies of Cr-substituted Zn-Mn ferrites

Graphical abstract: Variation of dielectric constant with frequency. Research highlights: {yields} Sol-gel route synthesized spherical crystalline nanoparticles of ZnMn{sub 1-x}Cr{sub x}FeO{sub 4}. {yields} XRD, DTA, FTIR, SEM, dielectric and impedance study. {yields} The ferrites show concentration dependence of ac electrical conductivity. {yields} Impedance response is dominated by grain boundary behavior. -- Abstract: Nanocrystalline ZnMn{sub 1-x}Cr{sub x}FeO{sub 4} (1.0 {>=} x {>=} 0) ferrites were synthesized by sol-gel technique. X-ray diffraction (XRD) confirmed the formation of single phasic cubic spinel lattice for all the compositions studied. Lattice parameter shows a decreasing trend with an increase in Cr content in the compositions. Formation of spherical nanoparticles was revealed by scanning electron microscopy (SEM) analysis. Infrared spectroscopic studies revealed two main absorption bands in the range 400-800 cm{sup -1} arising due to tetrahedral (A) and octahedral (B) site vibrations. Dielectric constant, dielectric loss tangent, ac conductivity and complex impedance were measured as a function of frequency in the range 20 Hz to 1 MHz. Frequency dependence of dielectric constant shows dielectric dispersion due to the Maxwell-Wagner type of interfacial polarization. The role of chromium in modifying structural and dielectric properties of these ferrites has been explained.

36 MATERIALS SCIENCE↗