Search NASA⌕ Search

SEARCH · Search NASA

Results for “full scale testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

Evaluation of laminar flow control system concepts for subsonic commercial transport aircraft

A two-year study conducted to establish a basis for industry decisions on the application of laminar flow control (LFC) to future commercial transports was presented. Areas of investigation included: (1) mission definition and baseline selection; (2) concepts evaluations; and (3) LFC transport configuration selection and component design. The development and evaluation of competing design concepts was conducted in the areas of aerodynamics, structures and materials, and systems. The results of supporting wind tunnel and laboratory testing on a full-scale LFC wing panel, suction surface opening concepts and structural samples were included. A final LFC transport was configured in incorporating the results of concept evaluation studies and potential performance improvements were assessed. Remaining problems together with recommendations for future research are discussed.

Source record↗

Solid Polymer Electrolyte (SPE) fuel cell technology program

The overall objectives of the Phase IV Solid Polymer Electrolyte Fuel Cell Technology Program were to: (1) establish fuel cell life and performance at temperatures, pressures and current densities significantly higher than those previously demonstrated; (2) provide the ground work for a space energy storage system based on the solid polymer electrolyte technology (i.e., regenerative H2/O2 fuel cell); (3) design, fabricate and test evaluate a full-scale single cell unit. During this phase, significant progress was made toward the accomplishment of these objectives.

Source record↗

Introduction to the arcopter arc wing and the Bertelsen effect for positive pitch stability and control

A brief report, offered on a wing design, new in geometry, construction, and flight characteristics. Preliminary wind tunnel data on a three-dimensional model was well as some full-scale man-carrying test results are included. There are photos of all phases of the experiments and some figures which serve to illustrate the Bertelsen Effect, a unique focus of aerodynamic forces in the arc wing system which allows the attainment of high lift coefficients with the maintenance of pitch stability and control.

Bertelsen, W. D.↗

XV-15 Tilt Rotor Research Aircraft - Program report

This paper is a status report of the NASA/Army XV-15 Project. The basic tilt-rotor concept and the XV-15 Tilt-Rotor Research Aircraft are discussed and some results of full-scale wind-tunnel tests in the Ames 40- by 80-Foot Wind Tunnel are presented. Flight-test data are included to give preliminary performance, noise, and vibration data in hover and as far into transition flight as are available at the time of presentation. Information concerning vehicle aerodynamics and airloads obtained as a result of both wind-tunnel and flight tests are provided with some conclusions as to the ramifications of the data in terms of design criteria and configuration layout.

Magee, J. P.↗

Foil system fatigue load environments for commercial hydrofoil operation

The hydrofoil fatigue loads environment in the open sea is examined. The random nature of wave orbital velocities, periods and heights plus boat heading, speed and control system design are considered in the assessment of structural fatigue requirements. Major nonlinear load events such as hull slamming and foil unwetting are included in the fatigue environment. Full scale rough water load tests, field experience plus analytical loads work on the model 929 Jetfoil commercial hydrofoil are discussed. The problem of developing an overall sea environment for design is defined. State of the art analytical approaches are examined.

Graves, D. L.↗

Energy efficient engine diffuser/combustor model technology

A full scale, full annular diffuser/combustor model test rig was tested to investigate how configurational changes affect pressure loss and flow separation characteristics. The rig was characterized by five major modules: inlet; prediffuser; strut; simulated combustor; and full combustor. The prediffuser featured a short, curved wall dump design. Performance goals included: (1) a separation-free prediffuser flow field; (2) total pressure loss limited to 3.0 percent in the prediffuser and shrouds; and (3) an overall section pressure loss of 5.5 percent P sub T3 at the design airflow distribution. The results indicated that the prediffuser configurations operate well within the program goals for pressure loss and demonstrate separation free operation over a wide range of inlet conditions.

Gardner, W.↗

Vehicle concepts and technology requirements for buoyant heavy-lift systems

Several buoyant-vehicle (airship) concepts proposed for short hauls of heavy payloads are described. Numerous studies identified operating cost and payload capacity advantages relative to existing or proposed heavy-lift helicopters for such vehicles. Applications involving payloads of from 15 tons up to 800 tons were identified. The buoyant quad-rotor concept is discussed in detail, including the history of its development, current estimates of performance and economics, currently perceived technology requirements, and recent research and technology development. It is concluded that the buoyant quad-rotor, and possibly other buoyant vehicle concepts, has the potential of satisfying the market for very heavy vertical lift but that additional research and technology development are necessary. Because of uncertainties in analytical prediction methods and small-scale experimental measurements, there is a strong need for large or full-scale experiments in ground test facilities and, ultimately, with a flight research vehicle.

Ardema, M. D.↗

Experiment pointing with magnetic suspension

A need has been identified for a payload auxilliary pointing system onboard the Space Shuttle which provides sub-arcsecond stability in the Shuttle disturbance environment. This paper describes such a pointing system, presently being developed by Sperry Flight Systems for the NASA Langley Research Center. At the core of the design is a non-contacting magnetic suspension which provides a high degree of isolation between payload and carrier. Design concepts and control laws will be discussed. Also, test results from full-scale protoflight hardware and planned system refinements will be presented.

Hamilton, B. J.↗

Full-scale wind-tunnel study of wing-fuselage interaction and comparison with paneling method

Full-scale wind-tunnel tests, conducted to determine the effects of three different airfoil sections on the aft-fuselage drag of a low-wing aircraft, are described. The measurements indicate a maximum difference in aft fuselage drag between the three airfoils of about 0.002. Measured changes in the locations of the fuselage pressure contours with airfoil section correlated well with the changes predicted by a three dimensional paneling code. A criterion, based on the inviscid computer code, is then proposed as an indicator for possible adverse viscous interactions at the wing-fuselage juncture.

Ross, J. C.↗

High-pressure liquid chromatography: A brief introduction and its application in analyzing the degradation of a C-ether (Thio-ether) liquid lubricant

The general principles of classical liquid chromatography and high pressure liquid chromatography (HPLC) are reviewed, and their advantages and disadvantages are compared. Several chromatographic techniques are reviewed, and the analytical separation of a C-ether liquid lubricant by each technique is illustrated. A practical application of HPLC is then demonstrated by analyzing a degraded C-ether liquid lubricant from full scale, high temperature bearing tests.

Source record↗

Thermoelectric temperature control system for the pushbroom microwave radiometer (PBMR)

A closed loop thermoelectric temperature control system is developed for stabilizing sensitive RF integrated circuits within a microwave radiometer to an accuracy of + or - 0.1 C over a range of ambient conditions from -20 C to +45 C. The dual mode (heating and cooling) control concept utilizes partial thermal isolation of the RF units from an instrument deck which is thermally controlled by thermoelectric coolers and thin film heaters. The temperature control concept is simulated with a thermal analyzer program (MITAS) which consists of 37 nodes and 61 conductors. A full scale thermal mockup is tested in the laboratory at temperatures of 0 C, 21 C, and 45 C to confirm the validity of the control concept. A flight radiometer and temperature control system is successfully flight tested on the NASA Skyvan aircraft.

Dillon-Townes, L. A.↗

Optical, thermal, and electrical performance of low-CR solar arrays

This paper describes the analysis and testing of a photovoltaic low-CR concentrator shaped like a truncated pyramid with an aperture of 0.5 m on a side and a geometric concentration ratio of six. The truncated base plane is covered by either silicon (Si) or gallium arsenide (GaAs) solar cells. Ray-trace analysis of the concentrator predicts a peak optical efficiency of 0.77, which falls off only gradually with pointing error. A coupled thermal-electrical analysis of the system shows that the moderately nonuniform illumination produced by the concentrator does not result in significant mismatch losses, provided the solar cells are connected in parallel groups. The results of ground tests involving a full-scale prototype concentrator conform well with theoretical predictions.

French, E. P.↗

Water impact laboratory and flight test results for the space shuttle solid rocket booster aft skirt

A series of water impact tests was conducted using full-scale segment representations of the Space Shuttle Solid Rocket Booster (SRB) aft skirt structure. The baseline reinforced structural design was tested as well as various alternative design concepts. A major portion of the test program consisted of evaluating foam as a load attenuation material. Applied pressures and response strains were measured for impact velocities from 40 feet per second (ft/s) to 110 ft/s. The structural configurations, test articles, test results, and flight results are described.

Kross, D. A.↗

Extension of ground-based testing for large space structures

A major concern for future large space structures is the ability to verify their dynamic characteristics by ground test. This article presents the results of the multiple boundary conditions test (MBCT) approach, which provides a complete ground test of a large structure that will provide, in turn, the data necessary to construct a test-verified final mathematical model. Theoretical studies indicate that this approach can provide a better final model than a ground test of the full-scale very flexible structure in a 1-g field. The approach is demonstrated by a mathematical simulation.

Wada, B. K.↗

Aeromechanical stability of a full-scale hingeless rotor in hover

The aeroelastic stability in hover of a 9.8-m-diam, hingeless helicopter rotor system is evaluated. Rotor inplane damping data were obtained for rotor operation between 350 and 425 rpm for thrust coefficients between 0.0 and 0.12. At constant rotor rotational speed, a minimum inplane damping level was obtained at a thrust coefficient of approximately 0.02. At constant rotor thrust, a minimum in rotor inplane damping was measured at 400 rpm. Correlation with a comprehensive aeroelastic stability program is found to be good. The influence of different aerodynamic inflow models on predicted damping levels is shown. Best correlation with experimental data is obtained using a dynamic inflow model rather than static or quasi-static inflow models. Comparison with other full-scale, hingeless rotor stability data in hover is presented. Also, direct comparisons are made with data from a full-scale bearingless main rotor test performed on the same general-purpose test apparatus. Although the bearingless rotor is more highly damped at design tip speed and 1-g thrust operation, greater sensitivity to operating conditions is shown.

Peterson, R. L.↗

Study of utilization of advanced composites in fuselage structures of large transports

The effort required by the transport aircraft manufacturers to support the introduction of advanced composite materials into the fuselage structure of future commercial and military transport aircraft is investigated. Technology issues, potential benefits to military life cycle costs and commercial operating costs, and development plans are examined. The most urgent technology issues defined are impact dynamics, acoustic transmission, pressure containment and damage tolerance, post-buckling, cutouts, and joints and splices. A technology demonstration program is defined and a rough cost and schedule identified. The fabrication and test of a full-scale fuselage barrel section is presented. Commercial and military benefits are identified. Fuselage structure weight savings from use of advanced composites are 16.4 percent for the commercial and 21.8 percent for the military. For the all-composite airplanes the savings are 26 percent and 29 percent, respectively. Commercial/operating costs are reduced by 5 percent for the all-composite airplane and military life cycle costs by 10 percent.

Jackson, A. C.↗

SRB/SLEEC (Solid Rocket Booster/Shingle Lap Extendible Exit Cone) feasibility study, volume 1

A preliminary design and analysis was completed for a SLEEC (Shingle Lap Extendible Exit Cone) which could be incorporated on the Space Transportation System (STS) Solid Rocket Booster (SRB). Studies were completed which predicted weights and performance increases and development plans were prepared for the full-scale bench and static test of SLEEC. In conjunction with the design studies, a series of supporting analyses were performed to assure the validity and feasibility of performance, fabrication, cost, and reliability for the selected design. The feasibility and required amounts of bench, static firing, and flight tests considered necessary for the successful incorporation of SLEEC on the Shuttle SRBs were determined. Preliminary plans were completed which define both a follow on study effort and a development program.

Baker, William H., Jr.↗

STOL and STOVL hot gas ingestion and airframe heating tests in the NASA Lewis 9- by 15-foot low-speed wind tunnel

Short takeoff and landing (STOL) and advanced short takeoff and vertical landing (STOVL) aircraft are being pursued for deployment near the end of this century. These concepts offer unique capabilities not seen in conventional aircraft: for example, shorter takeoff distances and the ability to operate from damaged runways and remote sites. However, special technology is critical to the development of this unique class of aircraft. Some of the real issues that are associated with these concepts are hot gas ingestion and airframe heating while in ground effects. Over the past nine years, NASA Lewis Research Center has been involved in several cooperative programs in the 9- by 15 Foot Low-Speed Wind Tunnel (LSWT) to establish a database for hot gas ingestion and airframe heating. The modifications are presented that were made in the 9- by 15-Foot LSWT, including the evolution of the ground plane, model support system, and tunnel sidewalls; and flow visualization techniques, instrumentation, test procedures, and test results. The 9- by 15-Foot LSWT tests were conducted at full scale exhaust nozzle pressure ratios. The headwind velocities varied from 8 to 120 kn depending on the concept (STOL or STOVL). Typical compressor-face distortions (pressure and temperature), ground plane contours, and model surface temperature profiles are presented.

Johns, Albert L.↗