Search NASA⌕ Search

SEARCH · Search NASA

Results for “phase transformations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

Low-temperature mechanochemical-thermal synthesis of {alpha}-Al{sub 2}O{sub 3} nanocrystals

Highlights: {yields} Polyaluminium chloride as {alpha}-Al{sub 2}O{sub 3} precursor was obtained by simple dissolution of Al rods in hydrochloric acid. {yields} A facile low temperature synthesis of {alpha}-Al{sub 2}O{sub 3} was obtained from 10 min high-energy ball milled and annealed polyaluminium chloride. {yields} {approx}15 nm {alpha}-Al{sub 2}O{sub 3} nanocrystals emended in amorphous alumina matrix were prepared at temperature as low as 400 {sup o}C. {yields} Gradual {alpha}-Al{sub 2}O{sub 3} formation up to 1000 {sup o}C was obtained. {yields} 50 nm {alpha}-Al{sub 2}O{sub 3} nanocrystals were obtained after annealing at 1000 {sup o}C. -- Abstract: The great capability of high-energy ball milled basic polyaluminium chloride gel (PACl) which consisted of the monomeric Al{sup 3+} ions and polymerized Al{sup 3+} species such as [Al{sub 13}O{sub 4}(OH){sub 24}(H{sub 2}O){sub 12}]{sup 7+} with a Keggin like structure to enhance the phase transformation into {alpha}-Al{sub 2}O{sub 3} nanocrystals at low temperature was verified. PACl gel 10 min milled and annealed at 400 {sup o}C, partially transformed to nanocrystalline {alpha}-Al{sub 2}O{sub 3} with the mean XRD crystallite size in the range of 15-17 nm, embedded in an amorphous or transition alumina matrix. Further crystal growth up to {approx}50 nm and phase pure {alpha}-Al{sub 2}O{sub 3} powder was obtained when heat-treated at 1000 {sup o}C. In contrast to this, the non-milled PACl gel transforms to the transition {theta}-Al{sub 2}O{sub 3} phase at 1000 {sup o}C. The evolution of {alpha}-Al{sub 2}O{sub 3} nanocrystals was studied by XRD, TEM, selected area electron diffraction (SAED) and high-resolution transmission electron microscopy (HRTEM) methods.

36 MATERIALS SCIENCE↗

Corrosion-induced microstructural developments in 316 stainless steel during exposure to molten Li 2 BeF 4 (FLiBe) salt

The microstructural evaluation and characterization of 316 stainless steel samples that were tested in molten Li 2 BeF 4 (FLiBe) salt were investigated in this study for evaluating its performance in high-temperature molten fluoride salts. Recently, 316 stainless steel and FLiBe salt are being actively considered as the main structural alloy and primary coolant of fluoride salt-cooled high-temperature reactor (FHR), a leading nuclear reactor concept for the next generation nuclear plants (NGNP). In support of the materials development for the FHR, high-temperature corrosion tests of 316 stainless steel in molten FLiBe salt at 700°C have been conducted in both bare graphite crucibles and 316 stainless steel-lined crucibles in an inert atmosphere for up to 3000 hours. The microstructure of the tested samples was comprehensively characterized using scanning electron microscopy (SEM) in conjunction with energy dispersive x-ray spectroscopy (EDS) and electron backscatter diffraction (EBSD), and scanning transmission electron microscopy (STEM) with EDS. In addition to the noticeable intergranular corrosion attack on surface, the corrosion in terms of the Cr depletion along high angle grain boundaries (15-180º) extended to 22µm in depth after 3000-hour exposure to molten FLiBe salt in graphite crucible. The coherent Σ3 grain boundary appeared high resistance to the Cr depletion. The substantial Cr depletion from the near-to-surface layer induced phase transformation from γ-martensite to α-ferrite phase (FeNi x ) during corrosion at 700ºC. Furthermore, the presence of graphite in the molten salt doubled the corrosion attack depth and led to the formation of round Mo2C, hexagonal Cr 7 C 3 and needle-like Al 4 C 3 phase within the alloy as deep as 50 µm after 3000-hour corrosion testing. Based on the microstructural analysis, the corrosion mechanisms of 316 stainless steel in molten FLiBe salt in different corrosion crucibles were illuminated through schematic diagrams. Additionally, a thermal diffusion controlled corrosion model was developed and validated by experimental data for predicting the long-term corrosion attack depth.

36 MATERIALS SCIENCE↗

Alpha phase precipitation from phase-separated beta phase in a model Ti-Mo-Al alloy studied by direct coupling of transmission electron microscopy and atom probe tomography

The benefit of direct coupling of APT with TEM dark field imaging to investigate early stages of phase transformation in multicomponent alloys is demonstrated by analyzing alpha phase precipitated in a model Ti-10 at% Mo-10 at% Al alloy during annealing at 400oC. Through such a direct coupling approach a thermodynamically unexpected solute partitioning trend between beta matrix and alpha precipitate is observed in the early stages of precipitation, which is explained based on possible nucleation of alpha phase in the Ti rich (Mo and Al depleted regions) created as a result of phase separation in beta matrix. On further higher temperature annealing at 600oC for 1 hour, the alpha precipitates were shown to grow and get enriched in Al and further depleted in Mo reaching the thermodynamic equilibrium.

Environmental Molecular Sciences Laboratory↗

Kinetic analyses for solid-state phase transition of metastable amorphous-AlO x (2.5 < x ≤ 3.0) nanostructures into crystalline alumina polymorphs

Solid-solid phase change materials (SS-PCMs) hold promise for energy storage/dissipation in batteries and energetic materials. Yet, phase change kinetics for SS-PCMs undergoing metastable to semi-stable/stable phase transformations remain relatively ill-studied because trapping metastable phases remain challenging. Recently, we demonstrated the kinetic entrapment and stabilization of a highly disordered and amorphous Al-oxide phase m-AlO x @C (x~2.5-3.0) via laser ablation synthesis in solution (LASiS). We report here, to our knowledge, the first chemical kinetics analysis for S-S phase transition of the m-AlO 3 @C nanocomposites (< 5–8 nm sizes) into semi-stable equilibrium alumina phases (θ/γ-Al 2 O 3 ) via disproportionation reaction, while releasing excess trapped gases. Our results indicate the atomic density of the AlO 3 structures to be ~5–10 times less than that of the final Al 2 O 3 phases, which led to the hypothesis of a volume shrinkage process during their phase transition. Temperature-dependent X-ray diffraction studies reveal the high-temperature phase transition for m-AlO 3 → θ/γ-Al 2 O 3 to follow contracting volume kinetics model, thereby validating our earlier hypothesis. Using the geometric volume contraction model, reaction kinetics analyses from Arrhenius plots reveal the activation energy barrier for the phase transition to be ~270±11 kJ/mol. This makes the activation energy barrier nearly identical to the oxidation of micron-sized Al particles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Highly Al-doped TiO{sub 2} nanoparticles produced by Ball Mill Method: structural and electronic characterization

Highlights: • Highly Al-doped TiO{sub 2} nanoparticles were synthesized using a Ball Mill Method. • Al doping delayed anatase to rutile phase transformation. • Al doping allow controlling the structural and electronic properties of nanoparticles. - Abstract: This study presents an easy method for synthesizing highly doped TiO{sub 2} nanoparticles. The Ball Mill method was used to synthesize pure and Al-doped titanium dioxide, with an atomic percentage up to 15.7 at.% Al/(Al + Ti). The samples were annealed at 773 K, 973 K and 1173 K, and characterized using ICP-AES, XRD, Raman spectroscopy, FT-IR, TG, STEM, XPS, and UV–vis spectroscopy. The effect of doping and the calcination temperature on the structure and properties of the nanoparticles were studied. The results show high levels of internal doping due to the substitution of Ti{sup 4+} ions by Al{sup 3+} in the TiO{sub 2} lattice. Furthermore, anatase to rutile transformation occurs at higher temperatures when the percentage of doping increases. Therefore, Al doping allows us to control the structural and electronic properties of the nanoparticle synthesized. So, it is possible to obtain nanoparticles with anatase as predominant phase in a higher range of temperature.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

9 T high magnetic field annealing effects on FeN bulk sample

α″-Fe{sub 16}N{sub 2} has been suggested as a promising candidate for future rare-earth-free magnets. In this paper, we report to use high magnetic field (9 T) assisted post-annealing process to enhance the Fe{sub 16}N{sub 2} phase formation in FeN bulk rod samples during the α′ → α″ phase transformation and thus improve its magnetic properties. It was found by X-ray Diffraction measurement that the volume ratio of Fe{sub 16}N{sub 2} phase was increased up to 22%, which corresponds to an increase in the amount of transformation from α′ → α″ up to 78%. Also, the saturation magnetization (M{sub s}) of the prepared FeN rod sample was increased to 227 emu/g with its coercivity up to 376 Oe at room temperature. A working mechanism for the high field assisted post-annealing process was presented.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

ζ-Glycine: insight into the mechanism of a polymorphic phase transition

Glycine is the simplest and most polymorphic amino acid, with five phases having been structurally characterized at atmospheric or high pressure. A sixth form, the elusive ζ phase, was discovered over a decade ago as a short-lived intermediate which formed as the high-pressure ϵ phase transformed to the γ form on decompression. However, its structure has remained unsolved. We now report the structure of the ζ phase, which was trapped at 100 K enabling neutron powder diffraction data to be obtained. The structure was solved using the results of a crystal structure prediction procedure based on fully ab initio energy calculations combined with a genetic algorithm for searching phase space. We show that the fate of ζ-glycine depends on its thermal history: although at room temperature it transforms back to the γ phase, warming the sample from 100 K to room temperature yielded β-glycine, the least stable of the known ambient-pressure polymorphs.

36 MATERIALS SCIENCE↗

The A1 to L1{sub 0} transformation in FePt films with ternary alloying additions of Mg, V, Mn, and B

The impact of ternary additions of Mg, V, Mn, and B on the A1 [face centered cubic (fcc)] to L1{sub 0} phase transformation has been studied. The films were cosputter deposited from elemental targets at room temperature and annealed after deposition. The films had Mg additions in the range {approx}0-2.6 at.%, V additions in the range 0.7-12.2 at.%, Mn additions in the range 2.2-16.3 at.%, and B additions in the range 1.2-12.9 at.%. For all four ternary alloy systems, annealing resulted in the formation of no other phases than the L1{sub 0} phase. Ternary additions of <1.8 at.% Mg, <5.8 at.% V, <6.0 at.% Mn, and <4.8 at.% B had little or no impact on the kinetic ordering temperature (KOT). The behavior of the activation energy for the transformation mirrored that for the KOT, except for Mg additions, which showed no measurable impact for the compositions studied. The transformation enthalpies for the ternary alloys were similar to those for binary FePt films. Only four of the films (with additions of 2.6 at.% Mg, 2.2 at.% and 6.0 at.% Mn, and 4.8 at.% B) for which the Curie transition was observed had lower T{sub C} than the binary FePt films with the same Pt content.

36 MATERIALS SCIENCE↗

Deformation behavior of additively manufactured GP1 stainless steel

In-situ neutron diffraction measurements were performed in this paper during heat-treating and uniaxial loading of additively manufactured (AM) GP1 material. Although the measured chemical composition of the GP1 powder falls within the composition specifications of 17-4 PH steel, a fully martensitic alloy in the wrought condition, the crystal structure of the as-built GP1 material is fully austenitic. Chemical analysis of the as-built material shows high oxygen and nitrogen content, which then significantly decreased after heat-treating in a vacuum furnace at 650 °C for one hour. Significant austenite-to-martensite phase transformation is observed during compressive and tensile loading of the as-built and heat-treated material with accompanied strengthening as martensite volume fraction increases. During loading, the initial average phase stress state in the martensite is hydrostatic compression independent of the loading direction. Finally, preferred orientation transformation in austenite and applied load accommodation by variant selection in martensite are observed via measurements of the texture development.

36 MATERIALS SCIENCE↗

Phase transitions of α-quartz at elevated temperatures under dynamic compression using a membrane-driven diamond anvil cell: Clues to impact cratering?

Coesite and stishovite are high-pressure silica polymorphs known to have been formed at several terrestrial impact structures. They have been used to assess pressure and temperature conditions that deviate from equilibrium formation conditions. Here in this paper, we investigate the effects of nonhydrostatic, dynamic stresses on the formation of high-pressure polymorphs and the amorphization of α-quartz at elevated temperatures. The obtained disequilibrium states are compared with those predicted by phase diagrams derived from static experiments under equilibrium conditions. We analyzed phase transformations starting with α-quartz in situ under dynamic loading utilizing a membrane-driven diamond anvil cell. Using synchrotron powder X-ray diffraction, the phase transitions of SiO 2 are identified up to 77.2 GPa and temperatures of 1160 K at compression rates ranging between 0.10 and 0.37 GPa s -1 . Coesite starts forming above 760 K in the pressure range between 2 and 11 GPa. At 1000 K, coesite starts to transform to stishovite. This phase transition is not completed at 1160 K in the same pressure range. Therefore, the temperature initiates the phase transition from α-quartz to coesite, and the transition from coesite to stishovite. Below 1000 K and during compression, α-quartz becomes amorphous and partially converts to stishovite. This phase transition occurs between 25 and 35 GPa. Above 1000 K, no amorphization of α-quartz is observed. High temperature experiments reveal the strong thermal dependence of the formation of coesite and stishovite under nonhydrostatic and disequilibrium conditions.

58 GEOSCIENCES↗

Electronic Structure, Chemical Bonding and Electrocatalytic Activity of Novel Ba(Fe0.7Ta0.3)O3-d Compounds

Ba(Fe0.7Ta0.3)O3-d (BFTO) compounds were synthesized using conventional, high-temperature solid-state ceramic reaction method by varying the sintering temperature (Ts=1200-1350 °C). The crystal structure, electronic structure and electrocatalytic activity of BFTO compounds were evaluated. Processing temperature induced phase transformations and structural quality influences the electronic structure and electrocatalytic activity of BFTO compounds. At Ts=1200 oC, Ba(Fe0.7Ta0.3)O3-d stabilizes in mixed phase of orthorhombic + rhombohedral phase (Amm2 + R3m). With increasing Ts (=1250 oC), Ba(Fe0.7Ta0.3)O3-d ceramics stabilize in tetragonal + rhombohedral [P4mm + R3m] mixed phase with a variation in the quantity of respective phases. High-resolution X-ray photoelectron spectroscopy of constituent elements, namely, Ba 3d, Fe2p, Ta 4f and O 1s reveal the electronic structure changes due to changes in chemical environment resulted from structural transformation. The electrocatalytic activity of BFTO was evaluated towards hydrogen evolution reaction (HER) and oxygen reduction reaction (ORR). Though all the samples demonstrated appreciable electrocatalytic properties, the best electrochemical catalytic activity was shown by BFTO samples sintered at 1350 °C. BFTO-1350 oC showed an onset potential of -0.690 V vs. RHE for HER and an onset potential of 0.73 V vs. RHE for ORR indicating its significant electrocatalytic performance. A general increase in activity with sintering temperature is potentially due to the improved structural quality of the BFTO ceramics. In addition to offering the fundamental insights into solid state materials based on doped BaTiO3 for electrocatalysis, the present work may contribute to the design and development of materials for high-temperature electrocatalytic converters.

Ba(Fe0.7Ta0.3)O3-d, Phase Transformation↗

Thermal conversion in air of rare-earth fluorides to rare-earth oxyfluorides and rare-earth oxides

Phase transformations of seven different rare-earth fluorides (i.e., REF3) where RE = La, Ce, Pr, Nd, Tm, Yb, Lu at temperatures ranging from 400–1400°C in air were investigated with X-ray diffraction. All of the REF3 compounds first transformed to oxyfluorides and then to oxides, with the exception of CeF3, which transformed directly to an oxide. This study focuses on the phase transitions of REF3 to REOx by simple heat-treatment processes in air and shows plausibility to remove RE elements from fluoride salt streams from molten salt reactors through fluoride-to-oxyfluoride or fluoride-to-oxide conversion mechanisms, which will result in precipitation. This could be used to remove fission product poisons from molten salt reactor waste streams. A waste form option for the resulting REOx products is lanthanide aluminoborosilicate (LABS) glass. To demonstrate this NdF3 was converted to Nd2O3 and immobilized in a LABS glass.

oxyfluoride, molten salt reactors, fluoride salt w↗

High-temperature X-ray analysis of phase evolution in lithium ion conductor Li{sub 1.5}Al{sub 0.5}Ge{sub 1.5}(PO{sub 4}){sub 3}

Series of Li{sub 1.5}Al{sub 0.5}Ge{sub 1.5}(PO{sub 4}){sub 3} glass ceramic samples were prepared in this work through the change of heat treatment temperature from 650 to 1050 °C. The structures of glass ceramic samples were characterized by means of high temperature X-ray diffraction and Field Emission Scanning Electron Microscope. And the lithium ionic conductivity was analyzed through AC impedance spectroscopy. Through heat treatment at 850 °C for 4 h for the base glass sample, we obtained a maximum conductivity of 5.8 × 10{sup −4} S/cm at room temperature. - Graphical Abstract: High temperature X-ray diffraction (HT-XRD) and Rietveld refinement of Li{sub 1.5}Al{sub 0.5}Ge{sub 1.5}(PO{sub 4}){sub 3} (LAGP) glass-ceramics were recorded to investigate the phase transformation, cell parameters and the mass fraction of each crystal phase, which occur in the glass to glass-ceramics process during different crystallization temperatures. The relationship between the average grain size and conductivity that originate from and relate to the crystallization temperature was analyzed by SEM micrograph and AC impedance spectroscopy. - Highlights: • Li{sub 1.5}Al{sub 0.5}Ge{sub 1.5}(PO{sub 4}){sub 3} glass-ceramics were prepared from as-prepared glass. • The phases decomposition and mass fraction of each phase were analyzed by HT-XRD. • Conductivity is relate to grain size that influenced by crystallization temperature.

36 MATERIALS SCIENCE↗

Crystal Chemistry and Electrochemistry of Li x Mn 1.5 Ni 0.5 O 4 Solid Solution Cathode Materials

For ordered high-voltage spinel LiMn 1.5 Ni 0.5 O 4 (LMNO) with the P4 3 2 1 symmetry, the two consecutive two-phase transformations at ~4.7 V (vs Li + /Li), involving three cubic phases of LMNO, Li 0.5 Mn 1.5 Ni 0.5 O 4 (L 0.5 MNO), and Mn 1.5 Ni 0.5 O 4 (MNO), have been well-established. Such a mechanism is traditionally associated with poor kinetics due to the slow movement of the phase boundaries and the large mechanical strain resulting from the volume changes among the phases, yet ordered LMNO has been shown to have excellent rate capability. In this paper, we show the ability of the phases to dissolve into each other and determine their solubility limit. We characterized the properties of the formed solid solutions and investigated the role of non-equilibrium single-phase redox processes during the charge and discharge of LMNO. Finally, by using an array of advanced analytical techniques, such as soft and hard X-ray spectroscopy, transmission X-ray microscopy, and neutron/X-ray diffraction, as well as bond valence sum analysis, the present study examines the metastable nature of solid-solution phases and provides new insights in enabling cathode materials that are thermodynamically unstable.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Direct extraction of lithium from ores by electrochemical leaching

With the rapid increase in lithium consumption for electric vehicle applications, its price soared during the past decade. To secure a reliable and cost-effective supply chain, it is critical to unlock alternative lithium extraction resources beyond conventional brine. In this study, we develop an electrochemical method to directly leach lithium from α-phase spodumene. We find the H 2 O 2 promoter can significantly reduce the leaching potential by facilitating the electron transfer and changing the reaction path. Upon leaching, β-phase spodumene shows a typical phase transformation to HAlSi 2 O 6 , while leached α-phase remains its original crystal phase with a lattice shrinkage. To demonstrate the scale-up potential of electrochemical leaching, we design a catalyst-modified high-throughput current collector for high loading of suspended spodumene, achieving a leaching current of 18 mA and a leaching efficiency of 92.2%. Electrochemical leaching will revolutionize traditional leaching and recycling processes by minimizing the environmental footprint and energy consumption.

25 ENERGY STORAGE↗

Cubic and hexagonal boron nitride phases and phase boundaries

We used temperature-dependent spark plasma sintering to induce phase transformations of metastable 3D c-BN to mixed-phase 3D/2D c-BN/h-BN and ultimately to the stable 2D h-BN phase at high temperature, useful for extreme-temperature technology.

Materials Science↗

Elasticity of some mantle crystal structures. I - Pleonaste and hercynite spinel.

The elasticity of high-pressure mantle phases can be characterized by using data for chemically similar crystal compounds. The single-crystal elastic constants are determined as a function of pressure and temperature for pleonaste spinel and at room conditions for hercynite spinel. The bulk modulus increases from 1.95 Mb for pleonaste spinel to 2.10 Mb for hercynite spinel. Low or negative values of the pressure derivatives of shear constants are characteristic of the spinel structure and imply a low kinetic barrier to phase transformations and diffusion. Compressional and shear velocities of the spinel phase of olivine are estimated as a function of mean atomic weight by using the pleonaste and hercynite data.

Wang, H.↗