Search NASA⌕ Search

SEARCH · Search NASA

Results for “COMPRESSIBILITY EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94

Investigation of possible csr induced energy spread effects with the A0 photoinjector bunch compressor

The bunch compressor of the A0 Photoinjector at Fermilab was removed this past spring to install a transverse to longitudinal emittance exchange experiment. Prior to its removal questions arose about the possibility of observing the effects of Coherent Synchrotron Radiation on the compressed beam. The energy spread of the beam with and without compression was measured to observe any changes. Various beam charges were used to look for square law effects associated with CSR. No direct observation of CSR in the compressor was attempted because the design of the vacuum chamber did not allow it. In this paper we report the results of these experiments and comparison with simulations using ASTRA and CSRTrack. The results are also compared with analytical approximations.

43 PARTICLE ACCELERATORS↗

Study of hydride reorientation and ductility of SRA ZIRLO and PRXA ZIRLO using ring compression testing (RCT)

Before dry storage, spent nuclear fuel is dried at high temperatures, which induces hydride dissolution. Radial hydride particles precipitate when cooled under a stress above a threshold stress. This process can severely degrade the ductility of cladding tubes. Zirconium alloys with different microstructures, such as grain boundary density, were quantified and studied to examine their effect on hydride reorientation. The ring compression loading mode creates a range of stress states depending on the location within the ring with respect to the applied load, producing various hydride morphologies that can be used to study the effects of microstructures on hydride reorientation. Finite element modeling was performed to calculate the hoop stress, which is the dominant stress, during hydride reorientation. These results were coupled with hydride morphology to determine the threshold stress for hydride reorientation, depending on the microstructure. In conclusion, the samples were then mechanically tested using ring compression to evaluate the ductility of zirconium alloys as a function of different hydride morphologies.

Hydride embrittlement↗

EFFECTS OF PORT FUEL AND DIRECT INJECTION STRATEGIES AND INTAKE CONDITIONS ON GASOLINE COMPRESSION IGNITION OPERATION

GGasoline compression ignition (GCI) using a single gasoline-type fuel for port fuel and direct injection has been shown as a method to achieve low-temperature combustion with low engine-out NOx and soot emissions and high indicated thermal efficiency. However, key technical barriers to achieving low temperature combustion on multi-cylinder engines include the air handling system (limited amount of exhaust gas recirculation (EGR)) as well as mechanical engine limitations (e.g. peak pressure rise rate). In light of these limitations, high temperature combustion with reduced amounts of EGR appears more practical. Furthermore, for high temperature GCI, an effective aftertreatment system allows high thermal efficiency with low tailpipe-out emissions. In this work, experimental testing was conducted on a 12.4 L multi-cylinder heavy-duty diesel engine operating with high temperature GCI combustion using EEE gasoline. Engine testing was conducted at an engine speed of 1038 rpm and brake mean effective pressure (BMEP) of 14 bar. Port fuel and direct injection strategies were utilized to increase the premixed combustion fraction. The impact on engine performance and emissions with respect to varying the injection and intake operating parameters was quantified within this study. A combined effect of reducing heat transfer and increasing exhaust loss resulted in a flat trend of brake thermal efficiency (BTE) when retarding direct injection timing, while increased port fuel mass improved BTE due to advanced combustion phasing and reduced heat transfer loss. Overall, varying intake valve close timing, EGR, intake pressure and temperature with the current pressure rise rate and soot emissions constraint was not effective in improving BTE, as the benefit of low heat transfer loss was always offset by increased exhaust loss.

Wang, Buyu↗

Hot/Wet Open Hole Compression Strength of Carbon/Epoxy Laminates for Launch Vehicle Applications

This Technical Memorandum examines the effects of heat and absorbed moisture on the open hole compression strength of carbon/epoxy laminates with the material and layup intended for the Ares I composite interstage. The knockdown due to temperature, amount of moisture absorbed, and the interaction between these two are examined. Results show that temperature is much more critical than the amount of moisture absorbed. The environmental knockdown factor was found to be low for this material and layup and thus obtaining a statistically significant number for this value needs to be weighed against a program s cost and schedule since basis values, damage tolerance, and safety factors all contribute much more to the overall knockdown factor.

Nettles, Alan T.↗

SZ3: A Modular Framework for Composing Prediction-Based Error-Bounded Lossy Compressors

Today's scientific simulations require a significant reduction of data volume because of extremely large amounts of data they produce and the limited I/O bandwidth and storage space. Here, error-bounded lossy compression has been considered one of the most effective solutions to the above problem. In practice, however, the best-fit compression method often needs to be customized or optimized in particular because of diverse characteristics in different datasets and various user requirements on the compression quality and performance. In this paper, we address this issue with a novel modular, composable compression framework named SZ3. Our contributions are four-folds. (1) We develop SZ3 which features an innovative modular abstraction for the prediction-based compression framework, such that compression modules can be plugged in easily to create new compressors based on characteristics of data and user requirements. (2) We create a new compression pipeline by SZ3 for GAMESS data, which significantly improves the compression ratios over state-of-the-art compressors. (3) We develop an adaptive compression pipeline by SZ3 for APS data with minimal efforts, which leads to the best rate-distortion among all existing error-bounded lossy compressors for any bit-rate. (4) We compare the sustainability of SZ3 with leading error-bounded prediction-based compressors, and then demonstrate the necessity of diverse pipelines by integrating and evaluating several compression pipelines on diverse scientific datasets from multiple disciplines. Experiments show that SZ3 incurs very limited overhead in compressor integration and our customized compression pipelines lead to up to 20% improvement in compression ratios under the same data distortion, when compared with the best existing approach.

97 MATHEMATICS AND COMPUTING↗

Anti-swirling demonstration

Fluid in bearings and seals, involved in motion due to shaft rotation and generating fluid dynamic forces, represents the well recognized source of instability known as whirl and whip. It is characterized by shaft forward circular precession at subysnchronous frequency. Control of the flow pattern in the bearing/seal clearance may enhance the stability. The rotor system demonstrates the dynamic effect of perturbation of the flow pattern in a seal gap by blowing compressed air in the rotor tangential direction. This effect results in shifting the rotor threshold of stability to a higher value of rotative speed when the air jet direction opposes rotation, and to a lower value of rotative speed when the air jet direction coincides with rotation. This effect implies that an unstable rotor can be stabilized by blowing air in the direction opposite to rotation. This technique is known as anti-swirl.

Muszynska, A.↗

Dose-response relationships for resetting of human circadian clock by light

Since the first report in unicells, studies across diverse species have demonstrated that light is a powerful synchronizer which resets, in an intensity-dependent manner, endogenous circadian pacemakers. Although it is recognized that bright light (approximately 7,000 to 13,000 lux) is an effective circadian synchronizer in humans, it is widely believed that the human circadian pacemaker is insensitive to ordinary indoor illumination (approximately 50-300 lux). It has been proposed that the relationship between the resetting effect of light and its intensity follows a compressive nonlinear function, such that exposure to lower illuminances still exerts a robust effect. We therefore undertook a series of experiments which support this hypothesis and report here that light of even relatively low intensity (approximately 180 lux) significantly phase-shifts the human circadian pacemaker. Our results clearly demonstrate that humans are much more sensitive to light than initially suspected and support the conclusion that they are not qualitatively different from other mammals in their mechanism of circadian entrainment.

NASA Discipline Regulatory Physiology↗

Rapid Calibration of High Resolution Geologic Models to Dynamic Data Using Inverse Modeling: Field Application and Validation

Streamline-based assisted and automatic history matching techniques have shown great potential in reconciling high resolution geologic models to production data. However, a major drawback of these approaches has been incompressibility or slight compressibility assumptions that have limited applications to two-phase water-oil displacements only. We propose an approach to history matching three-phase flow using a novel compressible streamline formulation and streamline-derived analytic sensitivities. First, we utilize a generalized streamline model to account for compressible flow by introducing an 'effective density' of total fluids along streamlines. Second, we analytically compute parameter sensitivities that define the relationship between the reservoir properties and the production response, viz. water-cut and gas/oil ratio (GOR). These sensitivities are an integral part of history matching, and streamline models permit efficient computation of these sensitivities through a single flow simulation. We calibrate geologic models to production data by matching the water-cut and gas/oil ratio using our previously proposed generalized travel time inversion (GTTI) technique. For field applications, however, the highly non-monotonic profile of the gas/oil ratio data often presents a challenge to this technique. In this work we present a transformation of the field production data that makes it more amenable to GTTI. Further, we generalize the approach to incorporate bottom-hole flowing pressure during three-phase history matching. We examine the practical feasibility of the method using a field-scale synthetic example (SPE-9 comparative study) and a field application. Recently Ensemble Kalman Filtering (EnKF) has gained increased attention for history matching and continuous reservoir model updating using data from permanent downhole sensors. It is a sequential Monte-Carlo approach that works with an ensemble of reservoir models. Specifically, the method utilizes cross-covariances between measurements and model parameters estimated from the ensemble. For practical field applications, the ensemble size needs to be kept small for computational efficiency. However, this leads to poor approximations of the cross-covariance matrix, resulting in loss of geologic realism. Specifically, the updated parameter field tends to become scattered with a loss of connectivities of extreme values such as high permeability channels and low permeability barriers, which are of special significance during reservoir characterization. We propose a novel approach to overcome this limitation of the EnKF through a 'covariance localization' method that utilizes sensitivities that quantify the influence of model parameters on the observed data. These sensitivities are used in the EnKF to modify the cross-covariance matrix in order to reduce unwanted influences of distant observation points on model parameter updates. The key to the success of the sensitivity-based covariance-localization is its close link to the underlying physics of flow compared to a simple distance-dependent covariance function as used in the past. This flow-relevant conditioning leads to an efficient and robust approach for history matching and continuous reservoir model updating, avoiding much of the problems in traditional EnKF associated with instabilities, parameter overshoots and loss of geologic continuity. We illustrate the power and utility of our approach using both synthetic and field applications.

58 GEOSCIENCES↗

Torsion Test of a Monocoque Box

A monocoque box beam consisting of a 24S-T aluminum-alloy sheet reinforced by four bulkheads and by longitudinal stringers and corner posts was subjected to bending loads as follows: pure bending about the lift axis, cantilever bending about the lift axis, and pure bending about both lift and drag axis. Longitudinal strains were measured for loads up to a load at which permanent set became measurable. The loads were sufficient to produce buckling of the sheet between stringers on the compression side of the box. The only noticeable effect of this buckling was a small increase in extreme-fiber strain on the compression side. The measured strains and measured deflections differed less than 10 percent from those computed from the simple beam theory after taking account of the effective width of the buckled sheet. The effect of the bulkheads on the distribution of stringer strain was negligible.

Mcpherson, Albert E↗

Effect of Residual Stresses on the Hardness of Bulk Metallic Glasses

Nanoindentation experiments were conducted on Zr-based metallic glass samples, which were elastically and plastically bent in order to investigate the effect of residual stresses on hardness. It was found that tensile residual stress reduced the hardness significantly, while compressive residual stress produced only a small effect on the hardness. These observations are consistent with three-dimensional continuum-plasticity-based finite-element simulations. The hardness was also found to vary more significantly with residual stresses, in particular in tension, than that caused by shear-banding-induced softening, suggesting hardness measurement is a practical method for the evaluation of tensile residual stresses in a metallic glass. Hardness variation in the bent sample was correlated with the residual-stress induced volume dilatation through a free-volume-based model. In this paper, we also present a detailed stress analysis based on yield asymmetry under tension and compression to describe the distribution of residual stresses in bent metallic glass specimens. The calculations agree well with the hardness variations measured experimentally.

36 MATERIALS SCIENCE↗

Internal Shock Interactions in Propulsion/Airframe Integrated Three-Dimensional Sidewall Compression Scramjet Inlets

The advantages and design requirements of propulsion/airframe integration for high Mach number flight have led to extensive study of the three-dimensional sidewall compression scramjet inlet in recent years. Recent research publications have indicated testing over a broad range of Mach number (2 to 18) in a variety of test gases, such as air, helium, and tetrafluoromethane. Multiple experimental techniques have been employed to obtain detailed internal shock interaction data, performance data, and inlet starting limits. Computational fluid dynamics has been effectively used for preliminary parametric studies as well as in parallel with experiments to aid in the explanation of unusual or unexpected flow phenomena. Inlets of this genre afford a relatively simple, generic geometry while producing a highly complex, three-dimensional flow field dominated by shock/shock and shock/boundary layer interactions. While the importance of the viscous effects in high speed inlet interactions is recognized, the present work addresses in a parametric fashion the inviscid effects of leading edge sweep, sidewall compression, and inflow Mach number on the internal shock structure in terms of inlet compression and mass capture. In the process, the source of the of the Mach number invariance with leading edge sweep for a constant sidewall compression class of inlet is identified, and a previously undocumented spillage phenomenon in a constant effective wedge angle class of inlets is discussed.

Holland, Scott D.↗

Plastic deformation of a porous bcc metal containing nanometer sized voids

Nanoporous materials, can present an outstanding range of mechanical properties. Here both molecular dynamics and dislocation analysis were used to evaluate and quantify the evolution of plasticity in a porous Ta single crystal containing randomly placed voids with 3.3 nm radii and average initial porosity of 4.1%, when subjected to uniaxial compressive strain. Nanovoids act as effective sources for dislocation emission. Dislocation shear loops nucleate at the surface of the voids and expand by the advance of the edge component. The evolution of dislocation configuration and densities were predicted by the molecular dynamics calculations and successfully compared to an analysis based on Ashby’s concept of geometrically-necessary dislocations. Resolved shear stress calculations were performed for all bcc slip systems and used to identify the operating Burgers vectors in the dislocation loops. The temperature excursion during plastic deformation was used to estimate the mobile dislocation density which is found to be less than 10% of the total dislocation density.

36 MATERIALS SCIENCE↗

Spark plasma sintering (SPS) densified U 3 Si 2 pellets: Microstructure control and enhanced mechanical and oxidation properties

Dense U 3 Si 2 pellets with controlled grain structure and enhanced thermal-mechanical and oxidation properties are synthesized with spark plasma sintering (SPS). Microstructure and phase composition of the SPS densified pellets are characterized systematically using SEM, EDS, and XRD. Thermal-mechanical properties and oxidation behavior of the sintered silicide fuel pellets are analyzed by laser flash, indentation, and dynamic thermogravimetric analysis. Dense U 3 Si 2 pellets are consolidated by combining high energy ball milling and rapid sintering by SPS, and the microstructure structures are controlled from micron-sized (~5.7 μm grain size) for conventional silicide to a nanocrystalline matrix with an average grain size of ~280 nm. A dominant phase of distorted U 3 Si 2 was identified with lattice expansion due to residual thermal stress upon SPS consolidation and rapid cooling processes. Both micron-sized and nano-sized pellets show exceptional thermal transport properties, consistent with monolithic silicides reported in literature. The SPS-densified pellets possess simultaneously high hardness and fracture toughness. The SPS-densified silicide pellets also demonstrate exceptional oxidation performance with extended onset oxidation temperature above 500 °C and reduced oxidation kinetics, particularly for nano-sized pellets. A strong strain effect was proposed in which compressive stress in nano-sized pellets enhances the oxidation resistance of silicide fuels, as evidenced by the degradation of oxidation performance upon strain relaxation by isothermal annealing. The correlation among the sintering process – microstructure control – physical properties and fuel behavior is established. A new concept of strain engineering is proposed further properties optimization, enabling the development of potential oxidation and corrosion-resistant silicides with extended performance, the key technological challenge of U 3 Si 2 as the leading concept of accident tolerant fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High pressure structural studies on SrRuO[subscript 3]

We have performed room temperature high pressure structural studies on the ferromagnetic perovskite SrRuO{sub 3} to 34 GPa. We have also used three different pressure media (silicone fluid, 4:1 methanol:ethanol and argon) to test for possible effects of pressure media on compression data. The orthorhombic perovskite structure is stable to the highest pressure, and the data can be fit with a bulk modulus of B{sub 0} = 192(3) GPa with a pressure derivative of B{prime}{sub 0} = 5.0(3) for all of the pressure media. We have also examined the high pressure behavior of the RuO{sub 6} octahedra using a model that assumes the octahedra are not distorted. Various tilt angles around the ideal cubic perovskite axes are found and can be used to estimate the Ru-O-Ru bond angle that is known to be directly related to the ferromagnetic Curie temperature. For all pressure media, there appears to be a minimum in the Ru-O-Ru bond angle around 15 GPa. Implications for the observed high pressure magnetic behavior of SrRuO{sub 3} will be discussed.

36 MATERIALS SCIENCE↗

Impact of electrode porosity architecture on electrochemical performances of 1 mm-thick LiFePO4 binder-free Li-ion electrodes fabricated by Spark Plasma Sintering

Thick electrodes with high active material loadings have been intensively studied over the last couple of decades in pursuit of achieving high energy density systems. To optimize and enhance the electrochemical performance of such electrodes, one has to control the pore morphology by, for example, varying the pore size and shape, and the level of porosity. In the present work, the fabrication of thick binder-free LiFePO4 (LFP) electrodes with two different pore sizes (12 and 20 mu m) and porosities (21 vol% and 44 vol%) using Spark Plasma Sintering (SPS) and templating approach is reported. The well-controlled porous architecture inside the thick electrodes is realized by fine-tuning experimental parameters. The impact of porosity architecture on electrochemical performance is quantified and correlated with the 3D tortuosity values determined from both micro-computed tomography and electrochemical impedance-based experimental methods. Based on the micro-computed tomography data analysis, estimated tortuosity values along X, Y, and Z axes reveal an anisotropic effect perpendicularly to the SPS compression axis (Z-direction). This is particularly profoundly observed in the samples with larger pores (20 mu m). The correlation between morphological properties and the rate capability performance is established indicating that the capacity loss happens mainly due to the Li-ion diffusion limitations.

Cathode material↗

Dynamics of 2D Dust Clusters with a Perpendicular Magnetic Field

The physics of two-dimensional (2D) dust clusters in an unmagnetized plasma sheath has been understood in dept. However, introduction of a perpendicular magnetic field into the dusty plasma sheath leads to some new effects, such as rotation and compression of dust clusters, whose mechanism is still unclear. It is found that even for a magnetic field as low as the earth magnetic field ({approx_equal}40 {mu}T), clusters rotate as rigid about their centers. It was proposed [U. Konopka, PRE 61, 1890 (2000)] that the ExB-induced ion flow drives the dust clusters into rotation. Simulations [L.-J. Hou, PoP 12, 042104 (2005)] based on the same hypothesis also reproduced the rotation of 2D clusters in a qualitative manner. However, this model cannot fully explain the experimental observations. We present detailed experimental investigations, which show that the rotation of a dust cluster critically depends on the detailed discharge geometry. In particular, the co-rotation of the background neutral gas and its role in driving dust-cluster rotation is proposed as a mechanism to set the dust cluster in rotation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Magnetorotational instability in a collisionless plasma with heat flux vector and an isotropic plasma with self-gravitational effect

The linear stability of a differential rotating magnetized plasma is analyzed in the collisionless approximation along with heat flux vector. The dispersion relation is derived and simplified cases are discussed with instability criteria presented. Anisotropic pressures are shown to not only alter the classical instability criterion but also induce new unstable regions. The shear rotating instability in a collisional magnetized plasma with a scalar kinetic pressure in the presence of self-gravitational effect is then considered. Three cases are discussed specifically according to the general dispersion relation. The effects of Jeans term and compressibility on the local shear instability induced by differential rotation are examined and the analytic instability criteria are presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗