Search NASA⌕ Search

SEARCH · Search NASA

Results for “Capping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94
All sourcesNASA NTRSDOE OSTI
DOE OSTI2014

Off state breakdown behavior of AlGaAs / InGaAs field plate pHEMTs

Off-state breakdown voltage, V{sub br}, is an important parameter determining the maximum power output of microwave Field Effect Transistors (FETs). In recent years, the use of field plates has been widely adopted to significantly increase V{sub br}. This important technological development has extended FET technologies into new areas requiring these higher voltages and power levels. Keeping with this goal, field plates were added to an existing AlGaAs / InGaAs pseudomorphic High Electron Mobility Transistor (pHEMT) process with the aim of determining the off-state breakdown mechanism and the dependency of V{sub br} on the field plate design. To find the mechanism responsible for breakdown, temperature dependent off-state breakdown measurements were conducted. It was found that at low current levels, the temperature dependence indicates thermionic field emission at the Schottky gate and at higher current levels, impact ionization is indicated. The combined results imply that impact ionization is ultimately the mechanism that is responsible for the breakdown in the tested transistors, but that it is preceded by thermionic field emission from the gate. To test the dependence of V{sub br} upon the field plate design, the field plate length and the etch depth through the highly-doped cap layer under the field plate were varied. Also, non-field plate devices were tested along side field plate transistors. It was found that the length of the etched region under the field plate is the dominant factor in determining the off-state breakdown of the more deeply etched devices. For less deeply etched devices, the length of the field plate is more influential. The influence of surface states between the highly doped cap layer and the passivation layer along the recess are believed to have a significant influence in the case of the more deeply etched examples. It is believed that these traps spread the electric field, thus raising the breakdown voltage. Three terminal breakdown voltages approaching 60V for the most deeply recessed devices are seen.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2014

Local control of magnetic damping in ferromagnetic/non-magnetic bilayers by interfacial intermixing induced by focused ion-beam irradiation

The influence of interfacial intermixing on the picosecond magnetization dynamics of ferromagnetic/non-magnetic thin-film bilayers was studied. Low-dose focused-ion-beam irradiation was used to induce intermixing across the interface between a 10 nm Ni{sub 81}Fe{sub 19} layer and a 2–3 nm capping layer of either Au or Cr. Time-resolved magneto-optical Kerr effect was used to study magnetization dynamics as a function of ion-beam dose. With an Au cap, the damping of the un-irradiated bilayer was comparable with native Ni{sub 81}Fe{sub 19} and increased with increasing ion dose. In contrast, for Ni{sub 81}Fe{sub 19}/Cr the damping was higher than that for native Ni{sub 81}Fe{sub 19}, but the damping decreased with increasing dose.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2014

Tuning of noble metal work function with organophosphonate nanolayers

We demonstrate that weak chemical interactions between untethered moieties in molecular nanolayers on metal surfaces can strongly influence the effective work function Φ{sub eff}. Electron spectroscopy shows that nanolayers of mercaptan-anchored organophosphonates on Au and Pt decrease Φ{sub eff}. The measured Φ{sub eff} shifts correlate with the chemical state of phosphonic acid moieties, and scale with molecular length. These results are contrary to predictions of ab initio calculations of monolayer-capped surfaces, but are consistent with calculations of bilayer-capped surfaces with face-to-face hydrogen-bonded phosphonic acid moieties. Our findings indicate that intra-layer bonding and layering in molecular nanolayers can be key to tailoring heterointerfacial electronic properties for applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2014

Synthesis and dielectric properties of zinc oxide nanoparticles using a biotemplate

Zinc Oxide nanoparticles are synthesized using DNA as capping agent. Zinc oxide nanoparticles are synthesized using DNA as a capping agent. Structural and morphological characterizations are done using SEM, FTIR and XRD. The particle size and lattice parameters are calculated from the diffraction data. The optical properties are studied using UV-Vis absorption spectroscopy and bandgap variation with temperature is determined. The dielectric property of nanoparticles is studied by varying temperature and frequency. The dielectric constant and dispersion parameters are found out. Method of Cole-Cole analysis is used to study the high temperature dispersion of relaxation time. The variation of both AC and DC conductivity are studied and activation energy calculated.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2014

Complex absorbing potential based Lorentzian fitting scheme and time dependent quantum transport

Based on the complex absorbing potential (CAP) method, a Lorentzian expansion scheme is developed to express the self-energy. The CAP-based Lorentzian expansion of self-energy is employed to solve efficiently the Liouville-von Neumann equation of one-electron density matrix. The resulting method is applicable for both tight-binding and first-principles models and is used to simulate the transient currents through graphene nanoribbons and a benzene molecule sandwiched between two carbon-atom chains.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2014

Direct imaging of thermally-activated grain-boundary diffusion in Cu/Co/IrMn/Pt exchange-bias structures using atom-probe tomography

Magnetic devices are often subject to thermal processing steps, such as field cooling to set exchange bias and annealing to crystallize amorphous magnetic electrodes. These processing steps may result in interdiffusion and the subsequent deterioration of magnetic properties. In this study, we investigated thermally-activated diffusion in Cu/Co/IrMn/Pt exchange biased polycrystalline thin-film structures using atom probe tomography. Images taken after annealing at 400 °C for 60 min revealed Mn diffusion into Co grains at the Co/IrMn interface and along Pt grain boundaries for the IrMn/Pt stack, i.e., a Harrison type C regime. Annealing at 500 °C showed further Mn diffusion into Co grains. At the IrMn/Pt interface, annealing at 500 °C led to a type B behavior since Mn diffusion was detected both along Pt grain boundaries and also into Pt grains. The deterioration of the films' exchange bias properties upon annealing was correlated to the observed diffusion. In particular, the topmost Pt capping layer thickness turned out to be crucial since a faster deterioration of the exchange bias properties for thicker caps was observed. This is consistent with the idea that Pt acts as a getter for Mn, drawing Mn out of the IrMn layer.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2014

Effect of multipole excitations in electron energy-loss spectroscopy of surface plasmon modes in silver nanowires

We have characterized the surface plasmon resonance (SPR) in silver nanowires using spatially resolved electron energy loss spectroscopy (EELS) in the scanning transmission electron microscope. Non-symmetric EELS spectra due to high-k SPR propagation along the nanowire and spectral shifts due to higher-order mode excitation are observed when the beam is positioned near the tip of the nanowire. When the beam is far from the tip region and on the side of nanowire, no spectral shifts are observed as the beam is scanned in the radial direction of the nanowire. The experimental spectra are compared with three different theoretical approaches: direct numerical calculation of the energy loss, analytical models for energy loss, and numerical simulations using an optical model. All three models reproduce the spectral shifts as the electron beam approaches the cap of the nanowire. The analytical model reveals the origin of the shifts in high-order plasmon mode excitation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2015

Properties of surface modes in one dimensional plasma photonic crystals

Properties of surface modes supported at the interface of air and a semi-infinite one dimensional plasma photonic crystal are analyzed. The surface mode equation is obtained by using transfer matrix method and applying continuity conditions of electric fields and its derivatives at the interface. It is observed that with increase in the width of cap layer, frequencies of surface modes are shifted towards lower frequency side, whereas increase in tangential component of wave-vector increases the mode frequency and total energy carried by the surface modes. With increase in plasma frequency, surface modes are found to shift towards higher frequency side. The group velocity along interface is found to control by cap layer thickness.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2015

Evidence of a reduction reaction of oxidized iron/cobalt by boron atoms diffused toward naturally oxidized surface of CoFeB layer during annealing

We have investigated the redox reaction on the surface of Ta/CoFeB/MgO/CoFeB magnetic tunnel junction stack samples after annealing at 300, 350, and 400 °C for 1 h using angle-resolved X-ray photoelectron spectroscopy for precise analysis of the chemical bonding states. At a capping tantalum layer thickness of 1 nm, both the capping tantalum layer and the surface of the underneath CoFeB layer in the as-deposited stack sample were naturally oxidized. By comparison of the Co 2p and Fe 2p spectra among the as-deposited and annealed samples, reduction of the naturally oxidized cobalt and iron atoms occurred on the surface of the CoFeB layer. The reduction reaction was more significant at higher annealing temperature. Oxidized cobalt and iron were reduced by boron atoms that diffused toward the surface of the top CoFeB layer. A single CoFeB layer was prepared on SiO{sub 2}, and a confirmatory evidence of the redox reaction with boron diffusion was obtained by angle-resolved X-ray photoelectron spectroscopy analysis of the naturally oxidized surface of the CoFeB single layer after annealing. The redox reaction is theoretically reasonable based on the Ellingham diagram.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

The elusive S{sub 2} state, the S{sub 1}/S{sub 2} splitting, and the excimer states of the benzene dimer

We observe the weak S{sub 0} → S{sub 2} transitions of the T-shaped benzene dimers (Bz){sub 2} and (Bz-d{sub 6}){sub 2} about 250 cm{sup −1} and 220 cm{sup −1} above their respective S{sub 0} → S{sub 1} electronic origins using two-color resonant two-photon ionization spectroscopy. Spin-component scaled (SCS) second-order approximate coupled-cluster (CC2) calculations predict that for the tipped T-shaped geometry, the S{sub 0} → S{sub 2} electronic oscillator strength f{sub el}(S{sub 2}) is ∼10 times smaller than f{sub el}(S{sub 1}) and the S{sub 2} state lies ∼240 cm{sup −1} above S{sub 1}, in excellent agreement with experiment. The S{sub 0} → S{sub 1} (ππ{sup ∗}) transition is mainly localized on the “stem” benzene, with a minor stem → cap charge-transfer contribution; the S{sub 0} → S{sub 2} transition is mainly localized on the “cap” benzene. The orbitals, electronic oscillator strengths f{sub el}(S{sub 1}) and f{sub el}(S{sub 2}), and transition frequencies depend strongly on the tipping angle ω between the two Bz moieties. The SCS-CC2 calculated S{sub 1} and S{sub 2} excitation energies at different T-shaped, stacked-parallel and parallel-displaced stationary points of the (Bz){sub 2} ground-state surface allow to construct approximate S{sub 1} and S{sub 2} potential energy surfaces and reveal their relation to the “excimer” states at the stacked-parallel geometry. The f{sub el}(S{sub 1}) and f{sub el}(S{sub 2}) transition dipole moments at the C{sub 2v}-symmetric T-shape, parallel-displaced and stacked-parallel geometries are either zero or ∼10 times smaller than at the tipped T-shaped geometry. This unusual property of the S{sub 0} → S{sub 1} and S{sub 0} → S{sub 2} transition-dipole moment surfaces of (Bz){sub 2} restricts its observation by electronic spectroscopy to the tipped and tilted T-shaped geometries; the other ground-state geometries are impossible or extremely difficult to observe. The S{sub 0} → S{sub 1}/S{sub 2} spectra of (Bz){sub 2} are compared to those of imidazole ⋅ (Bz){sub 2}, which has a rigid triangular structure with a tilted (Bz){sub 2} subunit. The S{sub 0} → S{sub 1}/ S{sub 2} transitions of imidazole-(benzene){sub 2} lie at similar energies as those of (Bz){sub 2}, confirming our assignment of the (Bz){sub 2} S{sub 0} → S{sub 2} transition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2015

Lifetime of inner-shell hole states of Ar (2p) and Kr (3d) using equation-of-motion coupled cluster method

Auger decay is an efficient ultrafast relaxation process of core-shell or inner-shell excited atom or molecule. Generally, it occurs in femto-second or even atto-second time domain. Direct measurement of lifetimes of Auger process of single ionized and double ionized inner-shell state of an atom or molecule is an extremely difficult task. In this paper, we have applied the highly correlated complex absorbing potential-equation-of-motion coupled cluster (CAP-EOMCC) approach which is a combination of CAP and EOMCC approach to calculate the lifetime of the states arising from 2p inner-shell ionization of an Ar atom and 3d inner-shell ionization of Kr atom. We have also calculated the lifetime of Ar{sup 2+}(2p{sup −1}3p{sup −1}) {sup 1}D, Ar{sup 2+}(2p{sup −1}3p{sup −1}) {sup 1}S, and Ar{sup 2+}(2p{sup −1}3s{sup −1}) {sup 1}P double ionized states. The predicted results are compared with the other theoretical results as well as experimental results available in the literature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2015

Non-proportionality of magnetic anisotropy and damping in CoFeB/MgO-based systems

We study the relationship between anisotropy K and damping α in MgO/CoFeB/Ta/CoFeB/MgO/cap films using vector network analyzer ferromagnetic resonance. Capping the stack with Ta and changing the thickness of the top MgO layer allow us to create significant variations in anisotropy while keeping the thickness and process conditions of the magnetic layer constant. The change in anisotropy can be attributed to the degradation of the CoFeB/MgO interface due to Ta intermixing with MgO upon deposition. This hypothesis is supported by measurements of similar samples with the bottom MgO thickness varied instead, which exhibit no significant change in anisotropy. This method of varying K allows identifying a regime where a spin reorientation transition occurs while α remains constant, proving the non-proportionality of K and α in perpendicular CoFeB/MgO systems. The effects of changing the capping layer material, notably Ru, are also discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2015

Charge separation dynamics at bulk heterojunctions between poly(3-hexylthiophene) and PbS quantum dots

Photo-induced electron transfer between poly-(3-hexylthiophene) (P3HT) and small (2.4 nm) PbS quantum dots (QDs), capped by different ligands, was studied by picosecond and femtosecond time-resolved fluorescence and by photo-induced absorption (PIA) measurements. In line with previous experiments, we observed that the efficiency of the quenching of P3HT by PbS QDs increased upon decreasing the average thickness of the ligand shell. This trend was also observed in the PIA spectra and in prior work on the performance of photovoltaic devices where the active layer was a blend of P3HT with PbS QDs capped by different ligands. Combining the pico- and femtosecond fluorescence decays showed that the quenching in blend films of P3HT and PbS QDs treated with 1,4-benzenedithiol occurred over a broad time scale ranging from tens of femtoseconds to hundreds of picoseconds. This complex kinetics was attributed to exciton hopping followed by electron transfer to the conduction band of the QDs. We also compared the wavelength dependence of the internal quantum efficiency (IQE) in the hybrid photovoltaic devices to those devices where the photoactive layer consists of PbS QDs only. Although excitation in the first excitonic transition of the PbS QDs yielded a similar IQE in both devices, the IQE of the hybrid devices tripled at wavelengths where also P3HT started to absorb. This suggests that upon excitation of P3HT in the latter devices, charge generation occurs by photo-induced electron transfer from P3HT to the QDs rather than by energy transfer to the QDs followed by exciton dissociation in the QDs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2015

Observations on Si-based micro-clusters embedded in TaN thin film deposited by co-sputtering with oxygen contamination

Using scanning electron microscopy (SEM) and high-resolution x-ray photoelectron spectroscopy with the synchrotron radiation we investigated Si-based micro-clusters embedded in TaSiN thin films having oxygen contamination. TaSiN thin films were deposited by co-sputtering on fixed or rotated substrates and with various power conditions of TaN and Si targets. Three types of embedded micro-clusters with the chemical states of pure Si, SiO{sub x}-capped Si, and SiO{sub 2}-capped Si were observed and analyzed using SEM and Si 2p and Ta 4f core-level spectra were derived. Their different resistivities are presumably due to the different chemical states and densities of Si-based micro-clusters.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Effect of power and type of substrate on calcium-phosphate coating morphology and microhardness

As known, the influence of the different sputtering process parameters and type of substrate on structure of the deposited coating is important to identify, because these parameters are significantly affected on structure of coating. The studies of the morphology and microhardness of calcium-phosphate (CaP) coatings formed and obtained on the surface of titanium, zirconium, titanium and niobium alloy for different values of the power of radio frequency discharge are presented. The increase in the radio frequency (rf) magnetron discharge leads to the formation of a larger grain structure of the coating. The critical depths of indentation for coatings determining the value of their microhardness have been estimated. Mechanical properties of the composite material on the basis of the bioinert substrate metal and CaP coatings are superior to the properties of the separate components that make up this composite material.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Effect of a novel load-bearing trabecular Nitinol scaffold on rabbit radius bone regeneration

The research aim was to evaluate the bone regeneration capability of novel load-bearing NiTi alloy (Nitinol) scaffolds in a critical-size defect (CSD) model. High strength “trabecular Nitinol” scaffolds were prepared by PIRAC (Powder Immersion Reaction Assisted Coating) annealing of the highly porous Ni foam in Ti powder at 900°C. This was followed by PIRAC nitriding to mitigate the release of potentially toxic Ni ions. Scaffolds phase composition and microstructure were characterized by X-ray diffraction and scanning electron microscopy (SEM/EDS), and their mechanical properties were tested in compression. New Zealand white rabbits received bone defect in right radius and were divided in four groups randomly. In the control group, nothing was placed in the defect. In other groups, NiTi scaffolds were implanted in the defect: (i) as produced, (ii) loaded with bone marrow aspirate (BMA), and (iii) biomimetically CaP-coated. The animals were sacrificed after 12 weeks. The forelimbs with scaffolds were resected, fixed, sectioned and examined in SEM. New bone formation inside the scaffold was studied by EDS analysis and by the processing of backscattered electron images. Bone ingrowth into the scaffold was observed in all implant groups, mostly next to the ulna. New bone formation was strongly enhanced by BMA loading and biomimeatic CaP coating, the bone penetrating as much as 1–1.5 mm into the scaffold. The results of this preliminary study demonstrate that the newly developed high strength trabecular Nitinol scaffolds can be successfully used for bone regeneration in critical size defects.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Localized surface plasmon behavior of Ag-Cu alloy nanoparticles stabilized by rice-starch and gelatin

The purpose of this communication was to understand localized surface plasmon behavior of a series of Ag-Cu alloy nanoparticles capped by rice-starch and gelatin. The structures of dried powders were investigated with the help of X-ray diffraction. The analysis revealed Ag-rich and Cu-rich phases with maximum solid solubility of Cu ∼9 atom per cent; 8 atom per cent and Ag ∼ 16 atom per cent; 14 atom per cent in rice-starch and gelatin capped samples respectively. Transmission electron microscope was used for knowing the particle size as well as to supplement FCC phase formations of Ag-rich and Cu-rich solid phases arrived at based on X-ray diffraction studies. The UV-Vis spectra of sols were examined for the formation and stability of alloy nanoparticles. The temporal evolution of LSPR curves gave us to assert that the sol is stable for more than two months. Small angle X-ray scattering in the sol state was extensively utilized to understand nature of suspensions in terms of fractals. Such a study is important for having a correlation between LSPR behaviors with those of nanoparticle dispersion in aqueous media. It is believed that this work will be a contribution to the emerging field of plasmonics that include applications in the area of photophysical processes and photochemical reactions.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Preface to Special Topic: Plasmas for Medical Applications

Intense research effort over last few decades in low-temperature (or cold) atmospheric plasma application in bioengineering led to the foundation of a new scientific field, plasma medicine. Cold atmospheric plasmas (CAP) produce various chemically reactive species including reactive oxygen species (ROS) and reactive nitrogen species (RNS). It has been found that these reactive species play an important role in the interaction of CAP with prokaryotic and eukaryotic cells triggering various signaling pathways in cells.

60 APPLIED LIFE SCIENCES↗