Search NASA⌕ Search

SEARCH · Search NASA

Results for “DIODE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94

Fast self-heating in GaN-based laser diodes

We study the time evolution of the internal temperature of GaN-based laser diodes in pulsed operation using time resolved spectroscopy. Time dependent emission spectra are compared to continuous-wave measurements at different temperatures to relate changes in the longitudinal mode spectrum to the internal temperature. From the different shift in emission center and longitudinal modes, two subsystems are identified which heat up on different time scales: the charge carrier plasma and the crystal lattice. While the lattice takes several microseconds to reach thermal equilibrium, the plasma heats up within 20 ns after the onset of the electrical pulse. This behavior is attributed to the small heat capacity of the charge carrier plasma compared to the crystal lattice.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Diode laser welding of aluminum to steel

Laser welding of dissimilar materials was carried out by using a high power diode laser to join aluminum to steel in a butt-joint configuration. During testing, the laser scan rate was changed as well as the laser power: at low values of fluence (i.e. the ratio between laser power and scan rate), poor joining was observed; instead at high values of fluence, an excess in the material melting affected the joint integrity. Between these limiting values, a good aesthetics was obtained; further investigations were carried out by means of tensile tests and SEM analyses. Unfortunately, a brittle behavior was observed for all the joints and a maximum rupture stress about 40 MPa was measured. Apart from the formation of intermeltallic phases, poor mechanical performances also depended on the chosen joining configuration, particularly because of the thickness reduction of the seam in comparison with the base material.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Role of stable and metastable Mg-H complexes in p-type GaN for cw blue laser diodes

Secondary ion mass spectroscopy (SIMS) and capacitance-voltage measurements were combined to thoroughly study Mg doping in GaN layers grown by metal organic vapor phase epitaxy. First we found that the Mg steady-state incorporation regime occurs for a surface coverage of 0.3 monolayer. Additionally SIMS indicates that H incorporates proportionally with Mg until a certain [Mg] where [H] saturates. After thermal activation, [H] while being much lower still scales with [Mg]. These results suggest that H combines with Mg to form two different types of Mg-H complexes: a metastable one leading to the Mg acceptor after annealing, the other one (dominating at high [Mg]) being stable and electrically inactive. The obtained results allowed us optimizing doping conditions for blue laser diodes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Indium-tin-oxide-free tris(8-hydroxyquinoline) Al organic light-emitting diodes with 80% enhanced power efficiency

Efficient indium tin oxide (ITO)-free small molecule organic light-emitting diodes (SMOLEDs) with multilayered highly conductive poly(3,4-ethylenedioxy thiophene):poly(styrenesulfonate) (PEDOT:PSS) as the anode are demonstrated. PEDOT:PSS/MoO{sub 3}/N,N'-diphenyl- N,N'-bis(1-naphthylphenyl)-1,1'-biphenyl-4,4'-diamine (NPD)/tris(8-hydroxyquinoline) Al (Alq{sub 3})/4,7-diphenyl-1,10-phenanthroline (BPhen)/LiF/Al SMOLEDs exhibited a peak power efficiency of 3.82 lm/W, 81% higher than that of similar ITO-based SMOLEDs (2.11 lm/W). The improved performance is believed to be due to the higher work function, lower refractive index, and decreased surface roughness of PEDOT:PSS vs ITO, and to Ohmic hole injection from PEDOT:PSS to the NPD layer via the MoO{sub 3} interlayer. The results demonstrate that PEDOT:PSS can substitute ITO in SMOLEDs with strongly improved device performance.

14 SOLAR ENERGY↗

Spin-torque diode spectrum of ferromagnetically coupled (FeB/CoFe)/Ru/(CoFe/FeB) synthetic free layer

We investigated systematically the spin torque diode spectrum of a ferromagnetically coupled (FeB/CoFe)/Ru/(CoFe/FeB) synthetic free layer in an MgO-based magnetic tunnel junction. In the spectra, we observed single peaks shifted to higher frequency with increasing the in-plane magnetic fields, as expected from the ferromagnetic resonance of the FeB/CoFe adjacent to the MgO tunnel barrier. On the other hand, under the perpendicular fields, we observed several peaks below 6 GHz and around 10 GHz, which were rather insensitive to the field. These behaviors are different from our simple calculation taking account the interlayer coupling, suggesting that the excitation of magnetizations occurs in a complicated manner for the synthetic free layers.

36 MATERIALS SCIENCE↗

Atom probe tomography characterisation of a laser diode structure grown by molecular beam epitaxy

Atom probe tomography (APT) has been used to achieve three-dimensional characterization of a III-nitride laser diode (LD) structure grown by molecular beam epitaxy (MBE). Four APT data sets have been obtained, with fields of view up to 400 nm in depth and 120 nm in diameter. These data sets contain material from the InGaN quantum well (QW) active region, as well as the surrounding p- and n-doped waveguide and cladding layers, enabling comprehensive study of the structure and composition of the LD structure. Two regions of the same sample, with different average indium contents (18% and 16%) in the QW region, were studied. The APT data are shown to provide easy access to the p-type dopant levels, and the composition of a thin AlGaN barrier layer. Next, the distribution of indium within the InGaN QW was analyzed, to assess any possible inhomogeneity of the distribution of indium (''indium clustering''). No evidence for a statistically significant deviation from a random distribution was found, indicating that these MBE-grown InGaN QWs do not require indium clusters for carrier localization. However, the APT data show steps in the QW interfaces, leading to well-width fluctuations, which may act to localize carriers. Additionally, the unexpected presence of a small amount (x = 0.005) of indium in a layer grown intentionally as GaN was revealed. Finally, the same statistical method applied to the QW was used to show that the indium distribution within a thick InGaN waveguide layer in the n-doped region did not show any deviation from randomness.

36 MATERIALS SCIENCE↗

Nuclear radiation detectors based on a matrix of ion-implanted p-i-n diodes on undoped GaAs epilayers

Samples of nuclear detectors which represent matrices of p-i-n diodes were fabricated based on undoped gallium arsenide epitaxial layers by ion implantation technology. The detectors have a size of the active area of 0.4 Multiplication-Sign 0.4 and 0.9 Multiplication-Sign 0.9 cm{sup 2}. Electrical characteristics of fabricated detectors and results of measurements of fast neutrons spectra of {sup 241}Am-Be source by the recoil protons method are discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Recover soft x-ray spectrum using virtual flat response channels with filtered x-ray diode array

A method for the recovery of soft x-ray spectra in indirect-drive inertial confinement fusion experiments is presented. Virtual detection channels with bandpass responses are obtained using linear combinations of the channel response functions of a filtered x-ray diode array and a weighted correction is introduced to improve the recovery. These virtual channels can be used to calculate radiation fluxes in some specific photon energy bands and hence to recover the spectrum of the whole photon energy range from 80 eV to 4.5 keV. Examples are listed which demonstrate the capability of this method to unfold various spectra such as Planck spectra with different radiation temperatures and to obtain x-ray flux of certain narrow energy interval.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Note: Simple calibration of the counting-rate dependence of the timing shift of single photon avalanche diodes by photon interval analysis

The counting-rate dependence of the temporal response of single photon avalanche diodes (SPADs) is a critical issue for the accurate determination of the fluorescence lifetime. In this study, the response of SPADs was examined with analyzing the time interval of the detected photons. The results clearly show that the shift of the detection timing causes the counting-rate dependence of the temporal response, and this timing shift is solely determined by the time interval from the preceding photon. We demonstrate that this timing instability is readily calibrated by utilizing the macrotime data taken with the time-tag mode that is implemented in the time-correlated single photon counting modules.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Feasibility of supersonic diode pumped alkali lasers: Model calculations

The feasibility of supersonic operation of diode pumped alkali lasers (DPALs) is studied for Cs and K atoms applying model calculations, based on a semi-analytical model previously used for studying static and subsonic flow DPALs. The operation of supersonic lasers is compared with that measured and modeled in subsonic lasers. The maximum power of supersonic Cs and K lasers is found to be higher than that of subsonic lasers with the same resonator and alkali density at the laser inlet by 25% and 70%, respectively. These results indicate that for scaling-up the power of DPALs, supersonic expansion should be considered.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Absolute spectral characterization of silicon barrier diode: Application to soft X-ray fusion diagnostics at Tore Supra

This paper presents an experimental protocol for absolute calibration of photo-detectors. Spectral characterization is achieved by a methodology that unlike the usual line emissions-based method, hinges on the Bremsstrahlung radiation of a Soft X-Ray (SXR) tube only. Although the proposed methodology can be applied virtually to any detector, the application presented in this paper is based on Tore Supra's SXR diagnostics, which uses Silicon Surface Barrier Diodes. The spectral response of these n-p junctions had previously been estimated on a purely empirical basis. This time, a series of second-order effects, like the spatial distribution of the source radiated power or multi-channel analyser non linearity, are taken into account to achieve accurate measurements. Consequently, a parameterised physical model is fitted to experimental results and the existence of an unexpected dead layer (at least 5 {mu}m thick) is evidenced. This contribution also echoes a more general on-going effort in favour of long-term quality of passive radiation measurements on Tokamaks.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Determination of gain in AlGaN cladding free nitride laser diodes

The optical gain spectra of InGaN-based multiple-quantum-well (MQW) laser diodes (LDs) grown by plasma-assisted molecular beam epitaxy are compared for different emission wavelengths. Two AlGaN cladding free LDs with similar epitaxial structures but with different In compositions in MQW were grown to study the dependence of material gain on lasing wavelength. As the emission wavelength increased from 432 to 458 nm, the differential modal gain decreased from 5.7 to 4.7 cm/kA, and the optical losses increased from 40 to 46 cm{sup −1} resulting in an increase in threshold current density. This dependence is attributed to lower optical mode confinement of LD emitting at longer wavelength. We found a strong decrease of confinement factor with increasing wavelength.

36 MATERIALS SCIENCE↗

Theory and simulation of field emission diode oscillators

The results of a theoretical analysis of a diode oscillator with a field-emission cathode are presented. A small-signal analysis of self-excitation conditions is performed. The time-domain particle-in-cell code is developed, and the performance of an X-band oscillator is numerically demonstrated using the simulation code. The simulation shows a rather high output power and efficiency for reasonable values of cathode current density.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

High-current long-duration uniform electron beam generation in a diode with multicapillary carbon-epoxy cathode

The results of reproducibly generating an electron beam with a current density of up to 5 kA/cm{sup 2}, without the cathode-anode gap being shorted by the plasma formed inside the cathode carbon-epoxy capillaries, in a ∼350 kV, ∼600 ns diode, with and without an external guiding magnetic field, are presented. The cathode sustained hundreds of pulses without degradation of its emission properties. Time- and space-resolved emissions of the plasma and spectroscopy analyses were used to determine the cathode plasma's density, temperature, and expansion velocity.

36 MATERIALS SCIENCE↗

Degradation of InGaN/GaN laser diodes investigated by micro-cathodoluminescence and micro-photoluminescence

We present an investigation of the degradation of InGaN/GaN laser diodes grown on a GaN substrate. The results indicate that: (i) Ageing induces a significant increase in the threshold current (Ith) of the lasers, which is attributed to an increase in non-radiative recombination; (ii) Ith increase is correlated to a decrease in the micro-cathodoluminescence signal measured (after the removal of the top metallization) in the region under the ridge; (iii) micro-photoluminescence measurements indicate that constant current stress increases non-radiative recombination within the quantum wells (and not only within the barriers), and induces an increase in the emission wavelength of the degraded region.

36 MATERIALS SCIENCE↗

Time evolution of electron flow in a model diode: Non-perturbative analysis

Using a combination of Eulerian and Lagrangian variables we study the time evolution of the electron flow from a no-current state to a final state with the stationary current in a planar one-dimensional diode. The electrons can be injected externally or generated by the cathode via field emission governed by a current-field law. The initial zero current regime is replaced suddenly by injection or, in the case of field emission, by jumping the anode voltage from zero to a constant positive value. The case of equipotential electrodes and fixed injection is studied along with a positive anode potential. When the current is fixed externally, the approach to the stationary state goes without oscillations if the initial electron velocity is high enough and the anode can absorb the injected flow. Otherwise the accumulated space charge creates a potential barrier which reflects the flow and leads to its oscillations, but our method of analysis is invalid in such conditions. In the field emission case the flow goes to its stationary state through a train of decaying oscillations whose period is of the order of the electron transit time, in agreement with earlier studies based on perturbation techniques. Our approximate method does not permit very high cathode emissivity although the method works when the stationary current density is only about 10% smaller than the Child-Langmuir limit.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Low-noise low-jitter 32-pixels CMOS single-photon avalanche diodes array for single-photon counting from 300 nm to 900 nm

We developed a single-photon counting multichannel detection system, based on a monolithic linear array of 32 CMOS SPADs (Complementary Metal-Oxide-Semiconductor Single-Photon Avalanche Diodes). All channels achieve a timing resolution of 100 ps (full-width at half maximum) and a photon detection efficiency of 50% at 400 nm. Dark count rate is very low even at room temperature, being about 125 counts/s for 50 μm active area diameter SPADs. Detection performance and microelectronic compactness of this CMOS SPAD array make it the best candidate for ultra-compact time-resolved spectrometers with single-photon sensitivity from 300 nm to 900 nm.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Cyan laser diode grown by plasma-assisted molecular beam epitaxy

We demonstrate AlGaN-cladding-free laser diodes (LDs), operating in continuous wave (CW) mode at 482 nm grown by plasma-assisted molecular beam epitaxy (PAMBE). The maximum CW output power was 230 mW. LDs were grown on c-plane GaN substrates obtained by hydride vapor phase epitaxy. The PAMBE process was carried out in metal-rich conditions, supplying high nitrogen flux (Φ{sub N}) during quantum wells (QWs) growth. We found that high Φ{sub N} improves quality of high In content InGaN QWs. The role of nitrogen in the growth of InGaN on (0001) GaN surface as well as the influence of LDs design on threshold current density are discussed.

36 MATERIALS SCIENCE↗