Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRESSURE DEPENDENCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94

Thermal conductivity of solid cyclohexane in orientationally ordered and disordered phases

Thermal conductivity {Lambda}{sub P} of solid cyclohexane is measured at a pressure P = 0.1 MPa in the temperature range from 80 K to the melting point, which covers the ranges of low-temperature orientationally ordered phase II and high-temperature orientationally disordered phase I. Thermal conductivity {Lambda}{sub V} is measured at a constant volume in orientationally disordered phase I. The thermal conductivity measured at atmospheric pressure decreases with increasing temperature as {Lambda}{sub P} {proportional_to} T{sup -1.15} in phase II, whereas {Lambda}{sub P} {proportional_to} T{sup -0.3} in phase I. As temperature increases, isochoric thermal conductivity {Lambda}{sub V} in phase I increases gradually. The experimental data are described in terms of a modified Debye model of thermal conductivity with allowance for heat transfer by both phonons and 'diffuse' modes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Melting and lattice dynamics of sodium at high pressures. Ab initio quantum molecular-dynamics analysis

The melting and lattice dynamics of sodium are studied by quantum molecular dynamics simulation, i.e., with allowance for anharmonicity, at pressures up to 1 Mbar and temperatures up to 1000 K. The simulation results agree well with the experimental data and our earlier calculation performed ab initio in the quasi-harmonic approximation. The simulation results demonstrate that anharmonic interactions weakly affect the melting curve and the phonon frequencies of Na up to near-melting temperatures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Elastic constants of solids at high pressures

The isothermal and adiabatic nth-order (n {>=} 2) elastic constants of a loaded crystal are defined. These constants fully determine the behavior of solids at an arbitrary load and are controlled by both an interatomic interaction and an applied load. Expressions that relate these constants (of the second, third, and fourth order) to Brugger elastic constants of the corresponding order, which are only determined by an inter-atomic interaction, are found for cubic symmetry crystals under hydrostatic pressure. These expressions are used to calculate the equation of state and the second- and third-order elastic constants of bcc tantalum at T = 0 K over a wide pressure range (0-600 GPa) using an electron density functional method. The results of calculating the equation of state and the second-order elastic constants agree with available experimental data and the calculation results obtained in other works.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Pressure- and temperature-induced transformations in crystalline polymers of C{sub 60}

The great advantage of the C{sub 60} molecule is its potential for polymerization, due to which the molecule can be the building block of new all carbon materials. In addition, it contains, both sp{sup 2} and sp{sup 3} hybridized carbon atoms, which allows synthesizing new carbon materials with desired physicochemical properties using both types of carbon bonding. The one- and two-dimensional polymeric phases of C{sub 60} are prototype materials of this sort. Their properties, especially polymerization under pressure and room temperature via covalent bonding between molecules belonging to adjacent polymeric chains or polymeric layers, can be used for further development of new materials. The present review focuses on the study of the pressure-induced polymerization and thermodynamic stability of these materials and their recovered new phases by in-situ high-pressure Raman and X-ray diffraction studies. The phonon spectra show that the fullerene molecular cage in the high-pressure phases is preserved, while these polymers decompose under heat treatment into the initial fullerene C{sub 60} monomer.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Specific features of insulator-metal transitions under high pressure in crystals with spin crossovers of 3d ions in tetrahedral environment

For Mott insulators with tetrahedral environment, the effective Hubbard parameter U{sub eff} is obtained as a function of pressure. This function is not universal. For crystals with d{sup 5} configuration, the spin crossover suppresses electron correlations, while for d{sup 4} configurations, the parameter U{sub eff} increases after a spin crossover. For d{sup 2} and d{sup 7} configurations, U{sub eff} increases with pressure in the high-spin (HS) state and is saturated after the spin crossover. Characteristic features of the insulator-metal transition are considered as pressure increases; it is shown that there may exist cascades of several transitions for various configurations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Calculation of the thermodynamic parameters and the degree of ionization of argon at sonoluminescence

The results of the numerical simulation of the behavior of a system consisting a spherical bubble filled with gaseous argon and surrounded by water under the impact of an external periodic pressure are presented. It is shown that, under typical conditions for the experimental investigation of single-bubble sonoluminescence in such a system, conditions are created for its thermal ionization near the time instant of the maximum compression in the gas. This proves one of the main provisions of the polarization model of sonoluminescence.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Two-dimensional electrodynamic structure of the normal glow discharge in an axial magnetic field

Results are presented from numerical simulations of an axisymmetric normal glow discharge in molecular hydrogen and molecular nitrogen in an axial magnetic field. The charged particle densities and averaged azimuthal rotation velocities of electrons and ions are studied as functions of the gas pressure in the range of 1–5 Torr, electric field strength in the range of 100–600 V/cm, and magnetic field in the range of 0.01–0.3 T. It is found that the axial magnetic field does not disturb the normal current density law.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effect of Air Pressure on Parameters of Beam Current and X-Ray Radiation Generated in a Gas Diode

Parameters of a beam of runaway electrons and X-ray radiation generated in a gas diode at different atmospheric pressures are studied. It is shown that the maximum beam currents and intensities of X-ray radiation are generated at an air pressure of about 10{sup 2} Pa. Distribution of beam electrons with respect to energy is determined by the method of attenuation of beam current using aluminum filters with different thicknesses. The maximum of such a distribution corresponds to an electron energy of about 100 keV. The maximum exposure dose of X-ray radiation behind a copper-foil anode with a thickness of 30 μm is about 107 mR. It is shown that the beam electrons absorbed by elements of an X-ray detector affect the shape and amplitude of the desired signal at beam currents of greater than 35 A/cm{sup 2}.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Properties of a Ceramic Pyroelectric X-Ray Generator as Dependent on Residual-Gas Pressure

The properties of X-ray emission from a pyroelectric accelerator based on ferroelectric ceramics have been experimentally studied, including the maximum energy of X-ray photons and their maximum yield generated by accelerated electrons at various pressures of residual gas in the generator chamber. The maximum X-ray yield and maximum energy of X-ray photons and accelerated electrons have been observed at a residual-gas pressure of around several millitorr.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

TOUGHREACT (TREACT) v3.32

TOUGHREACT V3.32 is a 3-D reactive transport code that handles to non-isothermal, multiphase/multicomponent fluid flow, heat transport, aqueous and gaseous species advection-diffusion, and equilibrium/kinetic water-gas-rock-biological reactions. TOUGHREACT V3.32 is based on TOUGHREACT V3.0-OMP, with several new features including temperature and species-dependent aqueous species diffusion coefficients, addition of the EWASG EOS module, a new generalized Monod kinetics function, time-dependent pressure-temperature boundary conditions, new VisIt-compatible tecplot-format output files (with new flux and velocity vector component outputs), new input and output options, and improved global water mass balance and coupling between flow, transport and reactive chemistry.

Sonnenthal, Eric↗

Foam Delivery of Amendments for Vadose Zone Remediation – Propagation Performance in Unsaturated Sediments

Foam delivery of remedial amendments is potentially useful for vadose zone remediation because aqueous amendments are delivered while maintaining a low water content. The transport behavior of foam in the vadose zone is not well studied. Bench top scale column tests were conducted to investigate the foam transport, foaming gas and liquid propagation, pressure build up and distribution, influence of foam quality and sediment permeability on foam injection pressure, and liquid up-taking and distribution in sediments during foam flow in unsaturated sediments. Results indicated that under the unsaturated conditions, foaming gas front traveled much faster than the foam front where bubbles rupture was significant. A liquid front was formed ahead of the foam flow front. The accumulated liquid in this front was mainly composed of the water injected with foam. The foam injection pressure was mostly attributed to the resistance to foam flow from the sediment, but not to the movement of the water ahead of the foam front. Foam had a high effective viscosity compare to water. A near linear pressure distribution within the foam-occupied column section was observed. At fixed injection rate, higher foam quality resulted lower injection pressure. Higher permeability sediments did not necessarily have a lower foam injection pressure, as other factors such as the foam injection rate, foam bubble diameter, and sediment pore size also influenced the pressure. In the foam flushed region, the liquid uptake and the water content distribution in sediment was barely affected by the initial water content and the foam injection rate. The implications of these findings in field remediation application were discussed.

54 ENVIRONMENTAL SCIENCES↗

Toward a predictive understanding of low emission fuel-flexible distributed energy turbine systems.

Using hydrogen derived from coal in power generation is one of the potential strategies being considered for eliminating CO2 emissions from combustion. In a two-stage gas combustor, injection of hydrogen into a secondary combustor provides an effective means for achieving a wide range of power settings. However, when additional hydrogen is injected into the exit stream of the first stage turbine, the mixture may autoignite. This uncontrolled autoignition event is undesirable as it leads to strong acoustic waves and high levels of nitrogen oxides (NOx). Since hydrogen was not a main fuel in the past, studies of hydrogen combustion under gas turbine environments have not been extensively carried out. Autoignition of hydrogen depends on pressure in a nonlinear fashion and is sensitive to the unique transport properties of the small hydrogen molecules, making prediction of autoignition a very challenging task. For both steady and transient flames, Large Eddy Simulation (LES) is essential for obtaining a fundamental understanding of flame stability mechanisms. As such, this work performs a LES study aimed at modeling and understanding 1) key stability mechanism(s) related to flame propagation and/or autoignition, and 2) the effect of pressure on hydrogen combustion over the range of 1 to 20 bar.

Defilippo, Anthony↗

Calibrating the Abaqus Crushable Foam Material Model using UNM Data

Triaxial test data from the University of New Mexico and uniaxial test data from W-14 is used to calibrate the Abaqus crushable foam material model to represent the syntactic foam comprised of APO-BMI matrix and carbon microballoons used in the W76. The material model is an elasto-plasticity model in which the yield strength depends on pressure. Both the elastic properties and the yield stress are estimated by fitting a line to the elastic region of each test response. The model parameters are fit to the data (in a non-rigorous way) to provide both a conservative and not-conservative material model. The model is verified to perform as intended by comparing the values of pressure and shear stress at yield, as well as the shear and volumetric stress-strain response, to the test data.

36 MATERIALS SCIENCE↗

Impact of axial velocity and transmembrane pressure (TMP) on ARP filter performance

The Savannah River Site (SRS) is currently treating radioactive liquid waste with the Actinide Removal Process (ARP) and the Modular Caustic Side Solvent Extraction Unit (MCU). Recently, the low filter flux through the ARP of approximately 5 gallons per minute has limited the rate at which radioactive liquid waste can be treated. Salt Batch 6 had a lower processing rate and required frequent filter cleaning. Savannah River Remediation (SRR) has a desire to understand the causes of the low filter flux and to increase ARP/MCU throughput. One potential method for increasing filter flux is to adjust the axial velocity and transmembrane pressure (TMP). SRR requested SRNL to conduct bench-scale filter tests to evaluate the effects of axial velocity and transmembrane pressure on crossflow filter flux. The objective of the testing was to determine whether increasing the axial velocity at the ARP could produce a significant increase in filter flux. The authors conducted the tests by preparing slurries containing 6.6 M sodium Salt Batch 6 supernate and 2.5 g MST/L, processing the slurry through a bench-scale crossflow filter unit at varying axial velocity and TMP, and measuring filter flux as a function of time.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Letter Report on 500 nA Pulsed Current from Field Ionization Source

We recently produced a milestone 500 nA of pulsed current using 40 Ir field ionizer electrodes in our ion source. In conclusion, we have produced the milestone pulsed current of 500 nA using 40 electrochemically etched iridium tips in a field ionization source. The pulsed current output is repeatable and scales as expected with gas fill pressure and bias voltage. We expect these current will be sufficient to produce neutral yields of 1 ∙ 10 7 DT n/s.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

FY-2015 FES (Fusion and Energy Sciences) Joint Research Target: Final Report for the Period October 1st, 2014, through September 30th, 2015

Annual JRT-15 Target: Conduct experiments and analysis to quantify the impact of broadened current and pressure profiles on tokamak plasma confinement and stability. Broadened pressure profiles generally improve global stability but can also affect transport and confinement, while broadened current profiles can have both beneficial and adverse impacts on confinement and stability. This research will examine a variety of heating and current drive techniques in order to validate theoretical models of both the actuator performance and the transport and global stability response to varied heating and current drive deposition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Gap Analysis of Storage Conditions between NNSS and LANL for SAVY 4000 Use

As part of the gap analysis for utilizing the SAVY 4000® at NNSS, the hydrogen gas generation rate and the effect of atmospheric pressure changes on the maximum normal operating pressure (MNOP) of the SAVY container must be evaluated because the nuclear material characteristics and atmospheric conditions will not be the same for NNSS and LANL. This paper documents this analysis and demonstrates that the LANL SAVY Safety Analysis Report (SAR) is bounding with respect to the Nevada facilities.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Results for the Aboveground Configuration of the Boiling Water Reactor Dry Cask Simulator

The thermal performance of commercial nuclear spent fuel dry storage casks is evaluated through detailed numerical analysis. These modeling efforts are completed by the vendor to demonstrate performance and regulatory compliance. The calculations are then independently verified by the Nuclear Regulatory Commission (NRC). Carefully measured data sets generated from testing of full-sized casks or smaller cask analogs are widely recognized as vital for validating these models. Recent advances in dry storage cask designs have significantly increased the maximum thermal load allowed in a cask, in part by increasing the efficiency of internal conduction pathways, and also by increasing the internal convection through greater canister helium pressure. These same canistered cask systems rely on ventilation between the canister and the overpack to convect heat away from the canister to the environment for both above- and below-ground configurations. While several testing programs have been previously conducted, these earlier validation attempts did not capture the effects of elevated helium pressures or accurately portray the external convection of above-ground and below-ground canistered dry cask systems. The purpose of the current investigation was to produce data sets that can be used to test the validity of the assumptions associated with the calculations used to determine steady-state cladding temperatures in modern dry casks that utilize elevated helium pressure in the sealed canister in an above-ground configuration.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗