Search NASA⌕ Search

SEARCH · Search NASA

Results for “Phase 2”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94

First principle calculations of structural phase transition and electronic properties in AmTe

The tight-binding linear muffin-tin orbital (TB-LMTO) with in the local density approximation is used to calculate total energy, lattice parameters, bulk modulus, density of states and energy band structure of americium telluride at ambient as well as at high pressure. It is found that AmTe is stable in NaCl – type structure under ambient pressure. The phase transition pressure was found to be 15.0 GPa from NaCl-type (B{sub 1}-phase) structure to CsCl-type (B{sub 2}-phase) structure for this compound. From energy band diagram it is observed that AmTe exhibit metallic behaviour. The calculated ground state properties such as lattice parameters and bulk modulus are in general good agreement with the available results.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ab initio study of pressure induced structural and electronic properties in TmPo

We report an ab initio calculation of pressure induced structural phase transition and electronic properties of Thulium Polonide (TmPo).The total energy as a function of volume is obtained by means of self-consistent tight binding linear muffin-tin-orbital (TB-LMTO) method within the local density approximation (LDA). It is found that TmPo is stable in NaCl-type (B{sub 1}-phase) structure to CsCl-type (B{sub 2}-phase) structure of this compound in the pressure range of 7.0 GPa. We also calculate the lattice parameter (a{sub 0}), bulk modulus (B{sub 0}), band structure and density of states. From energy diagram it is observed that TmPo exhibit metallic behavior. The calculated values of equilibrium lattice parameter and bulk modulus are in general good agreement.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Development and testing of a high cycle life 30 A-h sealed AgO-Zn battery

A two-phase program was initiated to investigate design parameters and technology to develop an improved AgO-Zn battery. The basic performance goal was 100 charge/discharge cycles (22 h/2 h) at 50 percent depth of discharge following a six-month period of charged stand at room temperature. Phase 1, cell evaluation, involved testing 70 cells in five-cell groups. The major design variables were active material ratios, electrolyte concentrations, separator systems, and negative plate shape. Phase 1 testing showed that cycle life could be improved 10 percent to 20 percent by using greater ratios of zinc to silver oxide and higher electrolyte concentrations. Wedge-shaped negatives increased cycle life by nearly 100 percent. Phase 2 battery evaluation, which was initiated before the Phase 1 results were known completely, involved evaluation of six designs as 19-cell batteries. Only one battery exceeded 100 cycles following nine months charged stand.

Bogner, R. S.↗

User interface and operational issues with thermionic space power systems

Thermionic space power systems have unique features which facilitate predeployment operations, provide operational flexibility and simplify the interface with the user. These were studied in some detail during the SP-100 program from 1983 to 1985. Three examples are reviewed in this paper: (1) system readiness verification in the prelaunch phase; (2) startup, shutdown, and dormancy in the operations phase; (3) part-load operation in the operations phase.

Dahlberg, R. C.↗

10.2 Thermal-Structural Testing

Objective: Test a C/SiC Ruddervator Subcomponent under relevant thermal, mechanical & dynamic loading a) Thermal-structural mission cycling for re-entry and hypersonic cruise conditions; b) High-temperature modal survey to study the effect of heating on mode shapes, natural frequencies and damping. Supports NASA ARMD Hypersonics Material & Structures Program. Partners: NASA Dryden / Langley / Glenn, Lockheed-Martin, Materials Research & Design, GE CCP Test Phases - Phase 1: Acoustic-Vibration Testing (LaRC) completed - Phase 2: Thermal-Mechanical Testing (DFRC) in assembly - Phase 3: Mechanical Testing (DFRC) in assembly

Hudson, Larry D.↗

Flat microwave spectra seen at X-class flares

We report peculiar spectral activity of four large microwave bursts as obtained from the Solar Arrays at the Owens Valey Radio Observatory during observations of X-class flares on 24 May 1990 and 7, 8, 22 March 1991. Main observational points that we newly uncovered are: (1) flat flux spectra over 1-18 GHz in large amounts of flux ranging from 10(exp 2) to 10(exp 4) s.f.u. at the maximum phase, (2) a common evolutionary pattern in which the spectral region of dominant flux shifts from high frequencies at the initial rise to low frequencies at the decaying phase, and (3) unusual time profiles that are impulsive at high frequencies but more extended at lower frequencies. We carry out the model calculations of microwave spectra under assumptions of gyrosynchrotron mechanism and a dipole field configuration to reproduce the observational characteristics. Our results are summarized as follows. First, a flat microwave spectrum reaching up to 10(exp 2) - 10(exp 4) s.f.u. may occur in a case where a magnetic loop is extended to an angular size of approximately (0.7-7.0) x 10(exp -7) sterad and contains a huge number (N(E greater than 10 keV) approx. 10(exp 36) - 10(exp 38)) of nonthermal electrons with power-law index approx. 3-3.5 over the entire volume. Second, the observed spectral activity could adequately be accounted for by the shrinking of the region of nonthermal electrons to the loop top and by the softening of the power-law spectrum of electrons in a time scale ranging 3-45 min depending on the event. Third, the extended microwave activity at lower frequencies is probably due to electrons trapped in the loop top where magnetic fields are low. Finally, we clarify the physical distinction between these large, extended microwave bursts and the gradual/post-microwave bursts often seen in weak events, both of which are characterized by long-period activity and broadband spectra.

Lee, Jeongwoo W.↗

Quantitative Phase Analysis of Plasma-Treated High-Silica Materials

The paper presents the X-ray diffraction (XRD) analysis of the crystal structure of SiO{sub 2} in two modifications, namely quartzite and quartz sand before and after plasma treatment. Plasma treatment enables the raw material to melt and evaporate after which the material quenches and condenses to form nanoparticles. The Rietveld refinement method is used to identify the lattice parameters of SiO{sub 2} phases. It is found that after plasma treatment SiO{sub 2} oxides are in the amorphous state, which are modeled within the microcanonical ensemble. Experiments show that amorphous phases are stable, and model X-ray reflection intensities approximate the experimental XRD patterns with fine precision. Within the modeling, full information is obtained for SiO{sub 2} crystalline and amorphous phases, which includes atom arrangement, structural parameters, atomic population of silicon and oxygen atoms in lattice sites.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Re-investigation of high-temperature phase equilibria in Fe-rich Sm–Fe–Ti alloys

Recently renewed attempts to develop high-performance rare-earth-lean permanent magnets based on the Sm(Fe,Ti) 12 compound have drawn attention to the limited knowledge about the high-temperature phase equilibria in the Sm–Fe–Ti system. Experimental investigation of equilibrated alloys with electron probe microanalysis, X-ray diffraction and thermomagnetic analysis revealed several inaccuracies in the currently accepted phase relations at 1000°C and allowed for a revision of the Fe-rich corner of the Sm–Fe–Ti phase diagram. The Sm(Fe,Ti) 12 and Sm 3 (Fe,Ti) 29 phases were found to have more extended Ti ranges of 5.1–9.7 at% and 2.8–6.9 at%, respectively. With increasing of the Ti content, the Curie temperature of the Sm(Fe,Ti) 12 remains nearly constant at 306–312°C, whereas that of the Sm 3 (Fe,Ti) 29 increases from 188°C to 207°C. The low-titanium Sm 3 (Fe,Ti) 29 phase equilibrates not only with the Sm(Fe,Ti) 12 and Sm2(Fe,Ti) 17 phases, but also with (α-Fe) solid solution. Newly demonstrated equilibrium between Sm 2 (Fe,Ti) 17 and TiFe 2 phases makes impossible the earlier reported equilibrium between the Sm 3 (Fe,Ti) 29 and Sm(Fe,Ti) 11 phases. Because of an invariant reaction at 1000 °C, the revised phase diagram also features a class II four-phase equilibrium Sm 3 (Fe,Ti) 29 + TiFe 2 + Sm(Fe,Ti) 12 + Sm 2 (Fe,Ti) 17 . Peritectic decomposition of the Sm(Fe,Ti) 11 phase, which occurs either at 1075°C or at 1087°C, was found to have among its products the Sm(Fe,Ti) 12 phase. Although no such equilibration was attempted, it must be possible to obtain above 1087°C a two-phase state composed of the Sm(Fe,Ti) 12 phase and a liquid – which is important for manufacturing of the Sm(Fe,Ti) 12 - based permanent magnets via the liquid-phase sintering.

36 MATERIALS SCIENCE↗

Effects of calcium and phosphate on uranium(IV) oxidation: Comparison between nanoparticulate uraninite and amorphous U IV –phosphate

The mobility of uranium in subsurface environments depends strongly on its redox state, with U IV phases being significantly less soluble than U VI minerals. This study compares the oxidation kinetics and mechanisms of two potential products of U VI reduction in natural systems, a nanoparticulate UO 2 phase and an amorphous U IV –Ca–PO 4 analog to ningyoite (CaU IV (PO 4 ) 2 ·1–2H 2 O). The valence of U was tracked by X-ray absorption near-edge spectroscopy (XANES), showing similar oxidation rate constants for U IV O 2 and U IV –phosphate in solutions equilibrated with atmospheric O 2 and CO 2 at pH 7.0 (k obs,UO2 = 0.17 ± 0.075 h -1 vs. k obs,U IV PO4 = 0.30 ± 0.25 h -1 ). Addition of up to 400 μM Ca and PO 4 decreased the oxidation rate constant by an order of magnitude for both UO 2 and U IV –phosphate. The intermediates and products of oxidation were tracked by electron microscopy, powder X-ray diffraction (pXRD), and extended X-ray absorption fine-structure spectroscopy (EXAFS). In the absence of Ca or PO 4 , the product of UO 2 oxidation is Na–uranyl oxyhydroxide (under environmentally relevant concentrations of sodium, 15 mM NaClO 4 and low carbonate concentration), resulting in low concentrations of dissolved U VI (<2.5 × 10 -7 M). Oxidation of U IV –phosphate produced a Na-autunite phase (Na 2 (UO 2 )PO 4 ·xH 2 O), resulting in similarly low dissolved U concentrations (<7.3 × 10 -8 M). When Ca and PO 4 are present in the solution, the EXAFS data and the solubility of the UVI phase resulting from oxidation of UO 2 and UIV–phosphate are consistent with the precipitation of Na-autunite. Bicarbonate extractions and Ca K-edge X-ray absorption spectroscopy of oxidized solids indicate the formation of a Ca–UVI–PO 4 layer on the UO 2 surface and suggest a passivation layer mechanism for the decreased rate of UO 2 oxidation in the presence of Ca and PO 4 . Interestingly, the extractions were unable to remove all of the oxidized U from partially oxidized UO 2 solids, suggesting that oxidized U is distributed between the interior of the UO 2 nanoparticles and the labile surface layer. Accounting for the entire pool of oxidized U by XANES is the likely reason for the higher UO 2 oxidation rate constants determined here relative to prior studies. In conclusion, our results suggest that the natural presence or addition of Ca and PO 4 in groundwater could slow the rates of U IV oxidation, but that the rates are still fast enough to cause complete oxidation of U IV within days under fully oxygenated conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Impacts of ethanol fuel level on emissions of regulated and unregulated pollutants from a fleet of gasoline light-duty vehicles

The study investigated the impact of ethanol blends on criteria emissions (THC, NMHC, CO, NOx), greenhouse gas (CO2), and a suite of unregulated pollutants in a fleet of gasoline-powered light-duty vehicles. The vehicles ranged in model year from 1984 to 2007 and included one Flexible Fuel Vehicle (FFV). Emission and fuel consumption measurements were performed in duplicate or triplicate over the Federal Test Procedure (FTP) driving cycle using a chassis dynamometer for four fuels in each of seven vehicles. The test fuels included a CARB phase 2 certification fuel with 11% MTBE content, a CARB phase 3 certification fuel with a 5.7% ethanol content, and E10, E20, E50, and E85 fuels. In most cases, THC and NMHC emissions were lower with the ethanol blends, while the use of E85 resulted in increases of THC and NMHC for the FFV. CO emissions were lower with ethanol blends for all vehicles and significantly decreased for earlier model vehicles. Results for NOx emissions were mixed, with some older vehicles showing increases with increasing ethanol level, while other vehicles showed either no impact or a slight, but not statistically significant, decrease. CO2 emissions did not show any significant trends. Fuel economy showed decreasing trends with increasing ethanol content in later model vehicles. There was also a consistent trend of increasing acetaldehyde emissions with increasing ethanol level, but other carbonyls did not show strong trends. The use of E85 resulted in significantly higher formaldehyde and acetaldehyde emissions than the specification fuels or other ethanol blends. BTEX and 1,3-butadiene emissions were lower with ethanol blends compared to the CARB 2 fuel, and were almost undetectable from the E85 fuel. The largest contribution to total carbonyls and other toxics was during the cold-start phase of FTP.

02 PETROLEUM↗

Crystal Phase Distribution and Ferroelectricity in Ultrathin HfO 2 –ZrO 2 Bilayers

(Hf,Zr)O 2 ultrathin films are used as ferroelectric layers in emerging digital logic and nonvolatile memory devices. The ferroelectric properties of (Hf,Zr)O 2 can be improved by interface engineering, such as the formation of nanolaminates with distinct HfO 2 and ZrO 2 layers. Herein, the ferroelectric performance of HfO 2 –ZrO 2 ultrathin bilayer devices is shown to depend on the stacking order of HfO 2 and ZrO 2 , which affects the quantity of the noncentrosymmetric orthorhombic Pca 2 1 crystal phase. By combining X‐ray diffraction with a novel extended X‐ray absorption fine structure (EXAFS) analysis procedure, the orthorhombic, tetragonal, and monoclinic phase fractions are quantified for bilayers composed of 3 nm HfO 2 and 3 nm ZrO 2 . A significantly larger orthorhombic ZrO 2 phase fraction is found when ZrO 2 has an unconstrained surface during annealing, whereas the presence of a ZrO 2 interface with the substrate results in a substantial tetragonal ZrO 2 phase fraction and a 2.4× smaller remanent polarization. HfO 2 is found to be less susceptible than ZrO 2 to crystal phase templating. The methods presented herein enable mechanistic studies of ferroelectric wake‐up, fatigue, and processing effects in (Hf,Zr)O 2 films, accelerating the development of electronic devices that rely on ferroelectric oxides.

McBriarty, Martin E.↗

Topical Report on Results of Plains CO 2 (PCOR) Partnership Phase II

The Plains CO 2 Reduction (PCOR) Partnership is one of seven Regional Carbon Sequestration Partnerships (RCSPs) competitively awarded by the U.S. Department of Energy (DOE) National Energy Technology Laboratory in 2003 as part of a national plan to mitigate greenhouse gas emissions. The PCOR Partnership is led by the Energy & Environmental Research Center at the University of North Dakota in Grand Forks, North Dakota, and includes more than 80 stakeholders from the public and private sector. The PCOR Partnership region includes all or parts of nine U.S. states and four Canadian provinces. Phase II, the validation phase, was an extension of the characterization phase (Phase I, 2003–2005) of the program and covered the period from 2005 through 2009. Phase II activities focused on carbon storage field validation projects that were designed to develop the local technical expertise and experience needed to facilitate future large-scale carbon dioxide storage efforts in the region’s subsurface and terrestrial settings. These activities included four field validation tests (three geologic and one terrestrial) along with continued refinement of the regional characterization of sequestration opportunities, elucidation and clarification of the regulatory and permitting requirements for sequestration as well as the identification of commercially available carbon dioxide capture technologies, integration of the regional efforts with the other DOE RCSPs, and continuation of local and regional public outreach initiatives. Results of the Phase II activities indicated that the PCOR Partnership region has tremendous opportunities for carbon sequestration in geologic and terrestrial settings. Total funding for Phase II exceeded $29 million, with 56% of that funding provided by DOE and the balance contributed by industry and other nonfederal partners. This report documents and summarizes all work performed over the course of the Phase II effort and presents the findings, recommendations, and conclusions of this work.

01 COAL, LIGNITE, AND PEAT↗

Structural Phase Transitions of Mg(BH[subscript 4])[subscript 2] under Pressure

The structural stability of Mg(BH{sub 4}){sub 2}, a promising hydrogen storage material, under pressure has been investigated in a diamond anvil cell up to 22 GPa with combined synchrotron X-ray diffraction and Raman spectroscopy. The analyses show a structural phase transition around 2.5 GPa and again around 14.4 GPa. An ambient-pressure phase of Mg(BH{sub 4}){sub 2} has a hexagonal structure (space group P61, a = 10.047(3) {angstrom}, c = 36.34(1) {angstrom}, and V = 3176(1) {angstrom}{sup 3} at 0.2 GPa), which agrees well with early reports. The structure of high-pressure phase is found to be different from reported theoretical predictions; it also does not match the high-temperature phase. The high-pressure polymorph of Mg(BH{sub 4}){sub 2} is found to be stable on decompression, similar to the case of the high-temperature phase. Raman spectroscopic study shows a similarity in high-pressure behavior of as-prepared Mg(BH{sub 4}){sub 2} and its high-temperature phase.

08 HYDROGEN↗

Comprehensive Gas-Phase Peptide Ion Structure Studies Using Ion Mobility Techniques: Part 2. Gas-Phase Hydrogen/Deuterium Exchange for Ion Population Estimation

Gas-phase hydrogen/deuterium exchange (HDX) using D{sub 2}O reagent and collision cross-section (CCS) measurements are utilized to monitor the ion conformers of the model peptide acetyl-PAAAAKAAAAKAAAAKAAAAK. The measurements are carried out on a home-built ion mobility instrument coupled to a linear ion trap mass spectrometer containing electron transfer dissociation (ETD) capabilities. ETD is utilized to obtain per-residue deuterium uptake data for select ion conformers, and a new algorithm is presented for interpreting the HDX data. Using molecular dynamics (MD) production data and a hydrogen accessibility scoring (HAS)-number of effective collisions (NEC) model, hypothetical HDX behavior is attributed to various in-silico candidate (CCS match) structures. The HAS-NEC model is applied to all candidate structures, and non-negative linear regression is employed to determine structure contributions resulting in the best match to deuterium uptake. The accuracy of the HAS-NEC model is tested with the comparison of predicted and experimental isotopic envelopes for several of the observed c-ions. It is proposed that gas-phase HDX can be utilized effectively as a second criterion (after CCS matching) for filtering suitable MD candidate structures. In this study, the second step of structure elucidation, 13 nominal structures were selected (from a pool of 300 candidate structures) and each with a population contribution proposed for these ions. .

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Dynamic high pressure phase transformation of ZrW 2 O 8

Phase transformations under high strain rates (dynamic compression) are examined in situ on ZrW 2 O 8 , a negative thermal expansion ternary ceramic displaying polymorphism. Amorphization, consistent with prior quasi-static measurements, was observed at a peak pressure of 3.0 GPa under dynamic conditions, which approximate those expected during fabrication. Evidence of partial amorphization was observed at lower pressure (1.8 GPa) that may be kinetically restrained by the short (<~150 ns) time scale of the applied high pressure. The impact of kinetics of pressure-induced amorphization from material fabrication methods is briefly discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Study of selected tether applications in space, phase 3, volume 2

The results of a Phase 3 study of two Selected Tether Applications in Space (STAIS); deorbit of a Shuttle and launch of an Orbital Transfer Vehicle (OTV), both from the space station using a tether were examined. The study objectives were to: perform a preliminary engineering design, define operational scenarios, develop a common cost model, perform cost benefits analyses, and develop a Work Breakdown Structure (WBS). Key features of the performance analysis were to identify the net increases in effective Shuttle cargo capability if tethers are used to assist in the deorbit of Shuttles and the launching of the OTVs from the space station and to define deployer system designs required to accomplish these tasks. Deployer concepts were designed and discussed. Operational scenarios, including timelines, for both tethered and nontethered Shuttle and OTV operations at the space station were evaluated. A summary discussion of the Selected Tether Applications Cost Model (STACOM) and the results of the cost benefits analysis are presented. Several critical technologies needed to implement tether assisted deployment of payloads are also discussed. Conclusions and recommendations are presented.

Source record↗

Assessment of Carbonated Brine Injection as Low-risk Strategy for Geologic Carbon Storage

The main objective of this early-phase research was to evaluate the techno-economic feasibility and risk associated with combined brine and CO 2 storage in SWD wells using brine dissolution in the North Dakota portion of the Williston Basin. Three simulation studies were conducted to investigate: (1) CO 2 phases at different conditions, (2) wellbore compatibility, and (3) long-term storage fate in reservoir. (1) A simple reservoir model and injection simulations were created using data to represent the BEST (brine extraction and storage test) site, an operational SWD facility located near Watford City, North Dakota. The pressure evolution caused by CO 2 comingled in produced water injectate in a layer cake reservoir was then modeled while tracking aqueous CO 2 throughout the project. The salinity of the injection water, the salinity of the reservoir brine, and the amount of dissolved CO 2 comingled in the injection water were varied. (2) A wellbore corrosion model was performed using the CO 2 concentrations selected based on the reservoir modeling to examine the carbonated produced water impact on wellbore. (3) Reactive transport modeling was conducted with the optimal CO 2 concentration for this injection site to study the rock-fluid interactions and CO 2 fate in the reservoir. Results suggest that CO 2 dissolved in produced water can be injected without appreciably increasing subsurface pressure or leakage risks. Pressure buildup was found to vary with salinity but not with CO 2 mass fraction. Simulation results show that lower CO 2 percent mass fraction leads to a higher amount of CO 2 that can be dissolved at a higher injection salinity. Furthermore, the long-term goal of dissolution trapping in a traditional carbon storage project is accomplished from the start, mitigating risks associated with potential migration of buoyant CO 2 , so long as the reservoir pressure and temperature are used to determine the maximum mass fraction of the dissolved CO 2 .

54 ENVIRONMENTAL SCIENCES↗

Reaction pathway analysis of (Ag x Cu 1-x )(In 0.75 Ga 0.25 )Se 2 with x = 0.75 and 1.0

Reaction pathways during formation of Ag(In 0.75 Ga 0.25 )Se 2 films were investigated by ex-situ characterization of time-progressive reactions using rapid thermal processing at 450 °C under 5% Ar/H 2 Se atmosphere. Composition measurements using energy dispersive x-ray spectroscopy (EDS) and X-ray fluorescence (XRF) show that with Ag/(Ag+Cu) = 1.0, Ga grading and Se uptake occur gradually up to 20 min. With 7 min reaction, there was no sign of a AgInSe 2 phase and only a Ag(In,Ga) 5 Se 8 chalcogenide phase formed. The reaction was completed with formation of Ag(In,Ga)Se 2 and Ag(In,Ga) 5 Se 8 within 20 min. The addition of Cu to the precursor so that Ag/(Ag+Cu) = 0.75 speeds up the reaction and reduces the formation of the Ag(In,Ga) 5 Se 8 phase. EDS and XRF analyses indicated that Ga grading and Se uptake were completed after 10 min. XRD analysis also shows formation of CuInSe 2 on the surface of the sample with Cu after 3.5 min reaction prior to other chalcogenide formation. On the other hand, a strong Ag(In,Ga)Se 2 (112) XRD peak appeared after 5 min reaction compared to 10 min reaction for 100% Ag films. EDS and Raman scattering measurements on the back-side of the films after delamination from the substrate indicated that Ga accumulated in AgGaSe 2 and Ga-Se phases at the back-side of films after 45 min reaction. XRD analysis showed that Ag tends to stay in the stable ζ-Ag 3 (In,Ga) phase during the reaction with Ag/(Ag+Cu) = 1.0, but not with 0.75, and this causes the longer reaction time and the non-uniformity.

14 SOLAR ENERGY↗