Search NASA⌕ Search

SEARCH · Search NASA

Results for “Polymer Science”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94

New insights on electro-optical response of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) film to humidity

Understanding the relative humidity (RH) response of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is critical for improving the stability of organic electronic devices and developing selective sensors. In this work combined gravimetric sensing, nanoscale surface probing, and mesoscale optoelectronic characterization are used to directly compare the RH dependence of electrical and optical conductivities and unfold connections between the rate of water adsorption and changes in functional properties of PEDOT:PSS film. We report three distinct regimes where changes in electrical conductivity, optical conductivity, and optical bandgap are correlated with the mass of adsorbed water. At low (RH < 25%) and high (RH > 60%) humidity levels dramatic changes in electrical, optical and structural properties occur, while changes are insignificant in mid-RH (25% < RH < 60%) conditions. We associate the three regimes with water adsorption at hydrophilic moieties at low RH, diffusion and swelling throughout the film at mid-RH, and saturation of the film by water at high RH. Optical film thickness increased by 150% as RH was increased from 9% to 80%. Low frequency (1 kHz) impedance increased by ~100% and film capacitance increased by ~30% as RH increased from 9% to 80% due to an increase in the film dielectric constant. Finally, changes in electrical and optical conductivities concomitantly decrease across the full range of RH tested.

36 MATERIALS SCIENCE↗

Manufacturing of Continuous Microporous Polymeric Fibers for Separation Applications

Polyolefin plastic waste, particularly polypropylene, is one of the most prevalent components in the plastic waste stream generated globally. However, only a small fraction of this waste is recycled and reintegrated into second applications. These materials have significant embedded energy that could be used for additional productivity if recycled properly. Therefore, there is a critical need to develop scalable processing techniques with high throughput to effectively recycle it. We report the continuous manufacturing of microporous fibers using waste polypropylene plastic and melt-processable lignin, a plant biomass constituent produced as a byproduct in paper mills or biorefineries, as a template to create pores. Further, these filaments with hierarchical porosity─created by controlled microphase separation during high-speed extensional flow followed by removal of lignin─exhibit exceptional capillary action for hydrophobic liquids. The resulting porous fibers can be used for various separation applications. For example, the oil uptake of the fibers is 9.59 ± 0.82 g/g for applications in oil recovery in bodies of water. In addition, polyethylenimine infiltration within these nanoporous fibers introduces cyclic room temperature sorption and thermal desorption potential of acidic gases such as CO 2 in a bench-scale experiment. The fibers exhibit multiple cycles of CO 2 absorption, with a range of 0.15 to 0.17 mmol/g. Thus, these polyethylenimine-infiltered nanoporous polypropylene fibers can also be used in removing acidic gases from a gas mixture.

36 MATERIALS SCIENCE↗

Recovery of p -Hydroxybenzoic Acid from Cu-Catalyzed Alkaline Hydrogen Peroxide Pretreatment of Hybrid Poplar

p-Hydroxybenzoic acid (pHBA) is present in some hardwood biomass feedstocks as an ester attached to the polymeric lignin subunits. Here, we report the isolation and recovery of pHBA from alkaline liquor waste streams obtained from fractionation of hybrid poplar using the “Cu-AHP process”. This process features two stages: alkaline pre-extraction (AP) of the biomass and copper-catalyzed alkaline hydrogen peroxide pretreatment. On a biomass scale of 100 g, 0.5 g of pHBA with a purity of 96% was obtained after decolorization and crystallization. The scalability of the purification process was demonstrated by using liquor obtained from the first-stage AP with 900 g of poplar biomass to afford 3.5 g of crystalline pHBA with 97% purity. Altogether, these results show that pHBA may be isolated and purified from waste streams generated in the two-stage Cu-AHP process without any alteration of the process conditions or impact on carbohydrate and lignin fractionation.

09 BIOMASS FUELS↗

Upcycling waste polystyrene to adipic acid through a hybrid chemical and biological process

Oxidative catalytic depolymerization of polystyrene (PS) can produce benzoic acid, but the annual consumption of benzoic acid is ~40 times lower than PS. For this catalytic oxidation method to be a viable means to manage PS waste, benzoic acid should be converted to higher-volume chemicals. We demonstrate a hybrid chemical and biological process that uses PS as feedstock for production of adipic acid, a high-volume co-monomer for nylon 6,6 via benzoic acid. Mn/Br co-catalyzed autoxidation of PS to benzoic acid proceeds with a yield of up to 94% in a solvent mixture of benzoic acid and water. The PS-derived benzoic acid undergoes bioconversion at near-quantitative yield to muconic acid, which is readily converted to adipic acid through catalytic hydrogenation. Process modeling, techno-economic analysis, and life cycle assessment estimate an adipic acid minimum selling price of $3.18/kg, with a 61% decrease in greenhouse gas emissions relative to production from fossil fuels.

09 BIOMASS FUELS↗

Solid polymer electrolyte from phosphorylated chitosan

Recently, the need of secondary battery application continues to increase. The secondary battery which using a liquid electrolyte was indicated had some weakness. A solid polymer electrolyte is an alternative electrolytes membrane which developed in order to replace the liquid electrolyte type. In the present study, the effect of phosphorylation on to polymer electrolyte membrane which synthesized from chitosan and lithium perchlorate salts was investigated. The effect of the component’s composition respectively on the properties of polymer electrolyte, was carried out by analyzed of it’s characterization such as functional groups, ion conductivity, and thermal properties. The mechanical properties i.e tensile resistance and the morphology structure of membrane surface were determined. The phosphorylation processing of polymer electrolyte membrane of chitosan and lithium perchlorate was conducted by immersing with phosphoric acid for 2 hours, and then irradiated on a microwave for 60 seconds. The degree of deacetylation of chitosan derived from shrimp shells was obtained around 75.4%. Relative molecular mass of chitosan was obtained by viscometry method is 796,792 g/mol. The ionic conductivity of chitosan membrane was increase from 6.33 × 10{sup −6} S/cm up to 6.01 × 10{sup −4} S/cm after adding by 15 % solution of lithium perchlorate. After phosphorylation, the ionic conductivity of phosphorylated lithium chitosan membrane was observed 1.37 × 10{sup −3} S/cm, while the tensile resistance of 40.2 MPa with a better thermal resistance. On the strength of electrolyte membrane properties, this polymer electrolyte membrane was suggested had one potential used for polymer electrolyte in field of lithium battery applications.

36 MATERIALS SCIENCE↗

In-situ photopolymerization of monodisperse and discoid oxidized methacrylated alginate microgels in a microfluidic channel

Here, we present a simple microfluidic technique to in-situ photopolymerize (by 365 nm ultraviolet) monodisperse oxidized methacrylated alginate (OMA) microgels using a photoinitiator (VA-086). By this technique, we generated monodisperse spherical OMA beads and discoid non-spherical beads with better shape consistency than ionic crosslinking methods do. We found that a high monomer concentration (8 w/v %), a high photoinitiator concentration (1.5 w/v %) and absence of oxygen are critical factors to cure OMA microgels. This photopolymerizing method is an alternative to current methods to form alginate microgels and is a simpler approach to generate non-spherical alginate microgels.

36 MATERIALS SCIENCE↗

An overview of bipolar plates in proton exchange membrane fuel cells

Bipolar plates are a crucial component of proton exchange membrane fuel cells. They are responsible for transporting reactant gases, carrying the current from the membrane electrode assembly to the end plates, providing heat and water management, and separating the individual cells. However, these plates also contribute to 80% of the fuel cell’s weight, 50% of its volume, and 40% of its cost, posing a barrier to the commercialization of fuel cells. This paper provides a comprehensive review of the materials and manufacturing processes used in the fabrication of bipolar plates as well as recent research conducted on the improvement of bipolar plate weight, volume, and cost through material selection and manufacturing methods. Additive manufacturing is highlighted in this work as an innovative manufacturing method to produce bipolar plates. Novel contributions in this paper include a detailed explanation of traditional manufacturing processes for metallic and graphitic-polymer bipolar plates as well as a cost comparison between additive and traditional manufacturing processes.

08 HYDROGEN↗

Properties of La 0.7 Ca 0.3 MnO 3 under extreme tensile strain

The complex phase diagram of manganites with simultaneously active spin, charge, orbital, and lattice degrees of freedom continues providing surprises. In a recent groundbreaking experiment, membranes of the perovskite manganite La 0.7 Ca 0.3 MnO 3 (LCMO) deposited on a flexible polymer layer were strained up to 8% [S. S. Hong et al., Science 368, 71 (2020)], much more than achieved by regular strain induced by a rigid substrate. By increasing this strain, a metal-insulator transition was reported. Here we reproduce the results of the experiments using Monte Carlo simulations of the two-orbital double-exchange model including Jahn-Teller distortions at hole density x=1/3. The full phase diagram with varying temperature and Jahn-Teller coupling λ is presented. When the bandwidth W of mobile electrons is reduced, thus when the effective Jahn-Teller coupling λ/W is increased, a metal-insulator transition is found in our simulations, between a ferromagnetic metallic state with uniform charge distribution and an insulator with diagonal charge stripes that retains its ferromagnetic character. In between the hole-rich diagonals, staggered orbital order occurs. We also report resistivity and magnetization measurements alongside with spin correlations and charge structure factors. Our overall conclusions are in agreement with the recent experimental and density functional theory results by Hong et al., and we confirm much earlier ground state predictions of striped ferromagnetic order using energy optimization techniques by T. Hotta et al. [Phys. Rev. Lett. 86, 4922 (2001)]. The experimental observation of one of the states predicted by theory suggests that diagonal stripes could be achieved at other hole densities as well, such as x=1/4, if LCMO membranes with that hole doping were subject to similar strains.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Morphology effects on spin-dependent transport and recombination in polyfluorene thin films

Here, we have studied the role of spin-dependent processes on conductivity in polyfluorene (PFO) thin films by preforming continuous wave (cw) electrically detected magnetic resonance (EDMR) spectroscopy at temperatures between 10 K and room temperature using microwave frequencies between about 1 GHz and 20 GHz, as well as pulsed EDMR at the X band (10 GHz). Variable frequency EDMR allows us to establish the role of spin-orbit coupling in spin-dependent processes whereas pulsed EDMR allows for the observation of coherent spin motion effects. We used PFO for this study in order to allow for the investigation of the effects of microscopic morphological ordering since this material can adopt two distinct intrachain morphologies: an amorphous (glassy) phase, in which monomer units are twisted with respect to each other, and an ordered (β) phase, where all monomers lie within one plane. In thin films of organic light-emitting diodes, the appearance of a particular phase can be controlled by deposition parameters and solvent vapor annealing, and is verified by electroluminescence spectroscopy. Under bipolar charge-carrier injection conditions, we conducted multifrequency cw EDMR, electrically detected Rabi spin-beat experiments, and Hahn echo and inversion-recovery measurements. Coherent echo spectroscopy reveals electrically detected electron-spin-echo envelope modulation due to the coupling of the carrier spins to nearby nuclear spins. Our results demonstrate that, while conformational disorder can influence the observed EDMR signals, including the sign of the current changes on resonance as well as the magnitudes of local hyperfine fields and charge-carrier spin-orbit interactions, it does not qualitatively affect the nature of spin-dependent transitions in this material. In both morphologies, we observe the presence of at least two different spin-dependent recombination processes. At room temperature and 10 K, polaron-pair recombination through weakly spin-spin coupled intermediate charge-carrier pair states is dominant, while at low temperatures, additional signatures of spin-dependent charge transport through the interaction of polarons with triplet excitons are seen in the half-field resonance of a triplet spin-1 species. This additional contribution arises since triplet lifetimes are increased at lower temperatures. We tentatively conclude that spectral broadening induced by hyperfine coupling is slightly weaker in the more ordered β-phase than in the glassy phase since protons are more evenly spaced, whereas broadening effects due to spin-orbit coupling, which impacts the distribution of g-factors, appear to be somewhat more significant in the β-phase.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Spatial correlation functions of paracrystals with radial symmetry

Here, we develop a phenomenological model to describe the structure of radially symmetric paracrystals whose long-range order are destroyed by propagation of particle fluctuations. General expressions are derived for the spatial correlation functions in one-, two-, and three-dimensional spaces. And the spatial correlation in paracrystals in reciprocal space is further discussed and clarified. The developed method can be used to quantitatively analyze the microstructure of paracrystalline materials in both real and reciprocal spaces via scattering experiments and computer simulations.

36 MATERIALS SCIENCE↗

Theory of Aging, Rejuvenation, and the Nonequilibrium Steady State in Deformed Polymer Glasses

The nonlinear Langevin equation theory of segmental relaxation, elasticity, and mechanical response of polymer glasses is extended to describe the coupled effects of physical aging, mechanical rejuvenation, and thermal history. The key structural variable is the amplitude of density fluctuations, and segmental dynamics proceeds via stress-modified activated barrier hopping on a dynamic free-energy profile. Mechanically generated disorder rejuvenation is quantified by a dissipative work argument and increases the amplitude of density fluctuations, thereby speeding up relaxation beyond that induced by the landscape tilting mechanism. The theory makes testable predictions for the time evolution and nonequilibrium steady state of the alpha relaxation time, density fluctuation amplitude, elastic modulus, and other properties. Model calculations reveal a rich dependence of these quantities on preaging time, applied stress, and temperature that reflects the highly nonlinear competition between physical aging and mechanical disordering. Thermal history is erased in the long-time limit, although the nonequilibrium steady state is not the literal fully rejuvenated freshly quenched glass. The present work provides the conceptual foundation for a quantitative treatment of the nonlinear mechanical response of polymer glasses under a variety of deformation protocols.

36 MATERIALS SCIENCE↗

Examination of an optical transmittance test for photovoltaic encapsulation materials

The optical transmittance of encapsulation materials is a key characteristic for their use in photovoltaic (PV) modules. Changes in transmittance with time in the field affect module performance, which may impact product warranties. Transmittance is important in product development, module manufacturing, and field power production (both immediate and long-term). Therefore, an international standard (IEC 62788-1-4) has recently been proposed by the Encapsulation Task-Group within the Working Group 2 (WG2) of the International Electrotechnical Commission (IEC) Technical Committee 82 (TC82) for the quantification of the optical performance of PV encapsulation materials. Existing standards, such as ASTM E903, are general and more appropriately applied to concentrated solar power than to PV. Starting from the optical transmittance measurement, the solar-weighted transmittance of photon irradiance, yellowness index (which may be used in aging studies to assess durability), and ultraviolet (UV) cut-off wavelength may all be determined using the proposed standard. The details of the proposed test are described. The results of a round-robin experiment (for five materials) conducted at seven laboratories to validate the test procedure using representative materials are also presented. For example, the Encapsulation Group actively explored the measurement requirements (wavelength range and resolution), the requirements for the spectrophotometer (including the integrating sphere and instrument accessories, such as a depolarizer), specimen requirements (choice of glass-superstrate and -substrate), and data analysis (relative to the light that may be used in the PV application). The round-robin experiment identified both intra- and inter-laboratory instrument precision and bias for five encapsulation materials (encompassing a range of transmittance and haze-formation characteristics).

14 SOLAR ENERGY↗

Examining Ohmic Losses in Fuel-Cell Catalyst Layers with Different Pt/C Ratios

A model of a fuel-cell cathode with distinct proton conductivities at the agglomerate and electrode scales was used to simulate polarization curves under conditions with facile oxygen transport. Here, the model was applied to electrodes containing agglomerates with different ratios of platinum to carbon in order to examine the hypothesis that intra-agglomerate proton conductivity is substantially lower than ionomer conductivity. The model predicts decreasing performance and increasing sensitivity to Pt/C ratio as intra-agglomerate conductivity declines relative to a constant through-electrode conductivity. Experiments on catalyst layers with Vulcan supports do not show the predicted trend indicating that mesoscale intra-agglomerate conductivity is not orders of magnitude lower than bulk ionomer conductivity.

08 HYDROGEN↗

In Silico Analysis of the Metabolic Potential and Niche Specialization of Candidate Phylum " Latescibacteria " (WS3)

The “Latescibacteria” (formerly WS3), member of the Fibrobacteres–Chlorobi–Bacteroidetes (FCB) superphylum, represents a ubiquitous candidate phylum found in terrestrial, aquatic, and marine ecosystems. Recently, single-cell amplified genomes (SAGs) representing the “Latescibacteria” were obtained from the anoxic monimolimnion layers of Sakinaw Lake (British Columbia, Canada), and anoxic sediments of a coastal lagoon (Etoliko lagoon, Western Greece). Here, we present a detailed in-silico analysis of the four SAGs to gain some insights on their metabolic potential and apparent ecological roles. Metabolic reconstruction suggests an anaerobic fermentative mode of metabolism, as well as the capability to degrade multiple polysaccharides and glycoproteins that represent integral components of green (Charophyta and Chlorophyta) and brown (Phaeophycaea) algae cell walls (pectin, alginate, ulvan, fucan, hydroxyproline-rich glycoproteins), storage molecules (starch and trehalose), and extracellular polymeric substances (EPSs). The analyzed SAGs also encode dedicated transporters for the uptake of produced sugars and amino acids/oligopeptides, as well as an extensive machinery for the catabolism of all transported sugars, including the production of a bacterial microcompartment (BMC) to sequester propionaldehyde, a toxic intermediate produced during fucose and rhamnose metabolism. Finally, genes for the formation of gas vesicles, flagella, type IV pili, and oxidative stress response were found, features that could aid in cellular association with algal detritus. Collectively, these results indicate that the analyzed “Latescibacteria” mediate the turnover of multiple complex organic polymers of algal origin that reach deeper anoxic/microoxic habitats in lakes and lagoons. The implications of such process on our understanding of niche specialization in microbial communities mediating organic carbon turnover in stratified water bodies are discussed.

59 BASIC BIOLOGICAL SCIENCES↗

On the optimized 3D printing and post-processing of PETG materials

Glycol-modified polyethylene terephthalate (PETG) is a reliable middle ground between polylactic acid and acrylonitrile butadiene styrene due to its light weight, impact resistance, toughness, flexibility, and cost-effectiveness. However, during 3D printing, the filament form is prone to oozing and stringing. In this study, we optimized the PETG printability via g-code setting and printing parameter modification, and consideration of filament quality, build plate temperature and leveling, and printing design complexity. Printed PETGs were thermally and chemically annealed, and post-processing conditions including annealing time, temperature, and solvent use were investigated. Mechanical properties were evaluated in terms of print parameter changes and post-processing techniques.

36 MATERIALS SCIENCE↗

On the direct ink write (DIW) 3D printing of styrene-butadiene rubber (SBR)-based adhesive sealant

Direct Ink Writing (DIW) utilizes a wide range of ink formulations to produce desirable 3D-printed structures and properties. Styrene-butadiene rubber (SBR) is an attractive candidate for 3D printing owing to its commercial availability, rheology, excellent mechanical properties, good impact resilience, and chemical stability. The SBR-based sealant was 3D printed in a DIW process, even in an ambient environment. The rheological behavior was assessed and correlated with optimized printing parameters. Important physico-chemical properties of the 3D-printed material were reported showing excellent properties as an elastomer. Finally, this work should expand the potential applications of existing rubber-based materials in additive manufacturing.

36 MATERIALS SCIENCE↗