Search NASA⌕ Search

SEARCH · Search NASA

Results for “Retrofitting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Structural optimization and recent large ground antenna installations

Within the past several years, the Jet Propulsion Laboratory has designed and built major ground antenna structures in Spain, Australia, and California. One of the antennas at each location is a 70 meter-diameter structure that is a retrofit of the existing 64 meter antenna. The 64 meter existing antennas were first stripped back to a 34 meter interior and then completely new construction with deeper trusses was added to extend the interior to 70 meters. The 70 meter project included the rare opportunity to collect field data to compare with predictions of the finite-element analytical models. The new quadripod design was tested for its lower mode natural frequencies and the main reflector was measured by theodolite to determine deflections of subsets of the backup-structure deformations under load. The emphasis here is to examine measurement results and possibly provide some appreciation of the relationship of predictions made from the design model to actual measurements.

Levy, Roy↗
NASA NTRS1988

Design considerations for beamwaveguide in the NASA Deep Space Network

A generalized solution is found for retrofitting a large dual-shaped reflector antenna for a beamwaveguide. The design is termed as a bypass beamwaveguide. Both highpass design feed imaging and bandpass design feed imaging are considered. Each design was studied using geometrical optics, Gaussian wave analysis, and both low-frequency and high-frequency diffraction analysis. An important extension of the Mizusawa-Kitsuregawa criteria was discovered (Zusama and Kitsuregawa, 1973). The principle revealed shows how a two-reflector cell, although in itself distorting, may be combined with a second cell which compensates for the first and delivers an output beam which is a good image of the input beam.

Veruttipong, Thavath↗
NASA NTRS1989

Lifting-surface theory for propfan vortices impinging on a downstream wing

Retrofitment of commercial aircraft with propfans could introduce undesirable aerodynamic sources of structure-borne noise that are absent for current turbojet powerplants. This paper theoretically examines the whipping action of the vortex wake from a generic propeller on the downstream rigid wing that supports it. The model addresses the high-frequency/compressible regime of most anticipated propfan implementations and produces an analytic solution for the distributed wing airload due to the periodic vortex impingement. The analysis also yields an expression for the local unsteady lift obtained from integration over an arbitrary internal patch of wing surface, for the purpose of applying a practical number of such forces at the nodes of a finite-element model for the corresponding structure (wing response results are not included in the present paper). Reported estimates of induced wing loads for a conventional-propeller example of demonstration appear to be in the reasonable range of expectation.

Martinez, R.↗
NASA NTRS1989

An improved, robust, axial line singularity method for bodies of revolution

The failures encountered in attempts to increase the range of applicability of the axial line singularity method for representing incompressible, inviscid flow about an inclined and slender body-of-revolution are presently noted to be common to all efforts to solve Fredholm equations of the first kind. It is shown that a previously developed smoothing technique yields a robust method for numerical solution of the governing equations; this technique is easily retrofitted to existing codes, and allows the number of circularities to be increased until the most accurate line singularity solution is obtained.

Hemsch, Michael J.↗
NASA NTRS1990

An Optimal Design For Steerable Dish Antenna With BWG

New design proposed for highly-efficient 34-m-diameter millimeter-wavelength antennas of NASA's Deep Space Network. Incorporates axial beam waveguide, BWG, and improved structure to maintain shape and alignment of reflecting surfaces. General approach to conceptual construction of structure to modularize overall system so critical constraint conditions pertaining to microwave optics and structural performance satisfied. Design retrofitted to existing NASA Deep Space Network 34-m antennas, or used as basis to build large ground-based steerable antennas. Engineering concepts involved in design adapted to design of other large, steerable antennas for telecommunications, radio astronomy, and military uses.

Chuang, K. L.↗
NASA NTRS1990

Remote Maintenance Monitoring

Automated system gives new life to aging network of computers. Remote maintenance monitoring system developed to diagnose problems in large distributed computer network. Consists of data links, displays, controls, software, and more than 200 computers. Uses sensors to collect data on failures and expert system to examine data, diagnose causes of failures, and recommend cures. Designed to be retrofitted into launch processing system at Kennedy Space Center. Reduces downtime, lowers workload and expense of maintenance, and makes network less dependent on human expertise.

Owens, Richard C.↗
NASA NTRS1990

External Peltier Cooler For Low-Noise Amplifier

Inexpensive Peltier-effect cooling module made of few commercially available parts used to reduce thermal noise in microwave amplifier. Retrofitted to almost any microwave low-noise amplifier or receiver preamplifier used in communication, telemetry, or radar. Includes copper or aluminum cold plate held tightly against unit to be cooled by strap-type worm-gear clamps.

Soper, Terry A.↗
NASA NTRS1990

AX-5 space suit bearing torque investigation

The symptoms and eventual resolution of a torque increase problem occurring with ball bearings in the joints of the AX-5 space suit are described. Starting torques that rose 5 to 10 times initial levels were observed in crew evaluation tests of the suit in a zero-g water tank. This bearing problem was identified as a blocking torque anomaly, observed previously in oscillatory gimbal bearings. A large matrix of lubricants, ball separator designs and materials were evaluated. None of these combinations showed sufficient tolerance to lubricant washout when repeatedly cycled in water. The problem was resolved by retrofitting a pressure compensated, water exclusion seal to the outboard side of the bearing cavity. The symptoms and possible remedies to blocking are discussed.

Loewenthal, Stuart↗
NASA NTRS1990

Tools for distributed application management

Distributed application management consists of monitoring and controlling an application as it executes in a distributed environment. It encompasses such activities as configuration, initialization, performance monitoring, resource scheduling, and failure response. The Meta system (a collection of tools for constructing distributed application management software) is described. Meta provides the mechanism, while the programmer specifies the policy for application management. The policy is manifested as a control program which is a soft real-time reactive program. The underlying application is instrumented with a variety of built-in and user-defined sensors and actuators. These define the interface between the control program and the application. The control program also has access to a database describing the structure of the application and the characteristics of its environment. Some of the more difficult problems for application management occur when preexisting, nondistributed programs are integrated into a distributed application for which they may not have been intended. Meta allows management functions to be retrofitted to such programs with a minimum of effort.

Marzullo, Keith↗
NASA NTRS1990

Tools for distributed application management

Distributed application management consists of monitoring and controlling an application as it executes in a distributed environment. It encompasses such activities as configuration, initialization, performance monitoring, resource scheduling, and failure response. The Meta system is described: a collection of tools for constructing distributed application management software. Meta provides the mechanism, while the programmer specifies the policy for application management. The policy is manifested as a control program which is a soft real time reactive program. The underlying application is instrumented with a variety of built-in and user defined sensors and actuators. These define the interface between the control program and the application. The control program also has access to a database describing the structure of the application and the characteristics of its environment. Some of the more difficult problems for application management occur when pre-existing, nondistributed programs are integrated into a distributed application for which they may not have been intended. Meta allows management functions to be retrofitted to such programs with a minimum of effort.

Marzullo, Keith↗
NASA NTRS1988

Bearing optimization for SSME HPOTP application

The space shuttle main engine (SSME) high-pressure oxygen turbopumps (HPOTP) have not experienced the service life required of them. To improve the life of the existing turbopump bearings, modifications to the bearings that could be retrofitted into the present bearing cavity are being investigated. Several bearing parameters were optimized using the computer program SHABERTH, which performs a thermomechanical simulation of a load support system. The computer analysis showed that improved bearing performance is feasible if low friction coefficients can be attained. Bearing geometries were optimized considering heat generation, equilibrium temperatures, and relative life. Two sets of curvatures were selected from the optimization: an inner-raceway curvature of 0.54, an outer-raceway curvature of 0.52, and an inner-raceway curvature of 0.55, an outer-raceway curvature of 0.53. A contact angle of 16 deg was also selected. Thermal gradients through the bearings were found to be lower with liquid lubrication than with solid film lubrication. As the coolant flowrate through the bearing increased, the ball temperature decreased but at a continuously decreasing rate. The optimum flowrate was approximately 4 kg/s. The analytical modeling used to determine these feasible modifications to improve bearing performance is described.

Armstrong, Elizabeth S.↗
NASA NTRS1989

Shuttle seated extraction feasibility study

Following the Space Shuttle Challenger accident, serious attention has turned to in-flight escape. Prior to the resumption of flight, a manual bailout system was qualified and installed. For the long term, a seated extraction system to expand the escape envelope is being investigated. This paper describes a 1987 study, conducted jointly by NASA/Johnson Space Center and Langley Research Center, to determine the feasibility of modifying the Space Shuttle Orbiters to incorporate the seated extraction system. Results of the study are positive, indicating retrofit opportunity and high probability of escape for early ascent, late entry, and even for uncontrolled flight such as the Challenger breakup. The system, as envisioned, can extract seven crewmembers within two seconds.

Onagel, Steven R.↗
NASA NTRS1989

Effect of advanced component technology on helicopter transmissions

Experimental tests were performed on the NASA/Bell Helicopter Textron (BHT) 500 hp advanced technology transmission (ATT) at the NASA Lewis Research Center. The ATT was a retrofit of the OH-58C helicopter 236 kW (317 hp) main rotor transmission, upgraded to 373 kW (500 hp), with a design goal of retaining long life with a minimum increase in cost, weight, and size. Vibration, strain, efficiency, deflection, and temperature experiments were performed and the results were compared to previous experiments on the OH-58A, OH-58C, and UH-60A transmissions. The high-contact-ratio gears and the cantilevered-mounted, flexible ring gear of the ATT reduced vibration compared to that of the OH-58C. The ATT flexible ring gear improved planetary load sharing compared to that of the rigid ring gear of the UH-60A transmission. The ATT mechanical efficiency was lower than that of the OH-58A transmission, probably due to the high-contact-ratio planetary gears.

Lewicki, D. G.↗
NASA NTRS1990

Interface standards for integrated forward-looking/predictive/reactive windshear systems

Forward-looking windshear systems are developing to a point (particularly the infrared sensors) where their interface with the cockpit and reactive windshear systems needs to be defined. As airlines retrofit their aircraft with reactive windshear systems, it is important to recognize that onboard windshear systems of the future will be a combination of both forward-looking and reactive elements. Today's reactive systems need to be built with the capability to interface with the forward-looking systems of tomorrow. This presentation is a first step at looking at the requirements and defining interface standards for integrated forward-looking and reactive windshear systems. Undoubtedly the requirements for interfacing these types of windshear systems will change as the technology changes.

Mcglinchey, Mark M.↗
NASA NTRS1991

Method for optimal configuration of an ECLSS on the Space Station Freedom

The establishment of a permanently manned Space Station represents a substantial challenge in the design of a life support system, specifically in the need to supply a large crew for missions of extended duration. The Space Station will evolve by time phased modular increments delivered and supplied by the Space Shuttle and other advanced launch systems. With the addition of each subsequent phase or alteration of mission duties, the requirements of the Station may differ from previous phases of development. With the addition of future crews and pressurized volume throughout the lifetime of the Space Station, change-out of individual subsystems may be necessary in order to meet the performance, safety, and reliability levels required from the Environmental Control and Life Support System (ECLSS). The analysis of this system growth demands the capability for advanced, integrated assessment techniques so that the unique mission drivers during each phase and mission scenario may be identified and evaluated. In order to determine the impacts of the interdependency between the ECLSS, the crew, the various user experiments, and the other distributed systems, consideration must be given to all Space Station resources and requirements during the initial and subsequent evolution phase. Therefore, it is necessary for analysis efforts to study the long term effects of established designs. These studies must quantify the optimal degree of loop closure within the capabilities of existing and future technologies including any resulting maintenance and logistics requirements. In addition, the necessity for subsystem retrofit during the lifetime of the Station must be examined. The source of system requirements due to long term exposure to the microgravity environment is illustrated, the criticality of the ECLSS functions is reviewed, and a method is described to develop an optimal design during each configuration based on the cross-consumption of Station resources. A comparison utilizing this procedure is discussed.

Gould, Marston J.↗
NASA NTRS1991

Advanced Software Development Workstation Project, phase 3

ACCESS provides a generic capability to develop software information system applications which are explicitly intended to facilitate software reuse. In addition, it provides the capability to retrofit existing large applications with a user friendly front end for preparation of input streams in a way that will reduce required training time, improve the productivity even of experienced users, and increase accuracy. Current and past work shows that ACCESS will be scalable to much larger object bases.

Source record↗
NASA NTRS1991

Status Update on the Seal/bearing Rotordynamics Test Facility at Case Western Reserve University

The CWRU Seal/Bearing test facility is shown along with the revised force measuring system. This facility has recently been retrofitted with a high pressure, high flow oil system. The high pressure high flow water system remains in place to test seals. Also, a new high flow air system is now installed. Thus, testing to determine static and dynamic properties can now be performed using oil, water, or air on this single facility. The oil system is currently being used to determine rotordynamic properties of a NASA four pocket hydrostatic journal bearing. The revised dual system force measuring configuration is performing with excellent accuracy. That is, the dynamic force measurements are made simultaneously with two independent systems, one with piezoelectric load cells and the other with strain gage load cells. The difference is less than 2 pct. between these two sets of load cell measurements on recent tests with a static eccentricity set close to zero and an orbit radius of 0.0004 inch. The extracted stiffness, damping and inertia coefficients is given for the test conditions shown, as extracted from the two independent dynamic force measurements.

Adams, Michael L.↗
NASA NTRS1990

Aeronautical satellite system test and implementation

This contribution reports on various aspects of the test and implementation of the new worldwide aeronautical satellite system. The system will be implemented in 1990 following several years of system design and equipment development. The full range of services and equipment will not be available immediately, but rather there will be a progressive phase-in over the first two years of service. Data services using low gain aircraft antennas are planned to be introduced first. Voice service, requiring high gain antennas is expected to begin on a full scale basis about May/June 1990. This contribution explains Inmarsat's approach to testing and authorization of equipment intended to make use of its satellites in this evolving situation. The approach is designed to permit progressive implementation of services while avoiding the need for large scale retrofitting of equipment which has already been introduced into service.

Smith, Keith↗