Search NASA⌕ Search

SEARCH · Search NASA

Results for “Structural Effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94

Effect of substrate temperature on structural and electrical properties of RF sputtered hafnium oxide thin films

In this work hafnium oxide thin films were deposited on p-type silicon substrate by Radio frequency magnetron sputtering at different substrate temperature ranging from room temperature to 300 °C. The structural and electrical properties of the sputtered films were investigated by x-ray diffraction, capacitance-voltage and current-voltage measurements. The XRD results show the formation monoclinic structure of the hafnium oxide thin films. The shifting of C-V curves towards negative voltage side depicts the increase in positive oxide charges with the rise of substrate temperature. Leakage current was found increased, when temperature enhanced from room temperature to 300 °C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Zn doping on structural and dielectric properties of tetragonal Ni{sub 1-x}Zn{sub x}Fe{sub 2}O{sub 4} (0.0 ≤ x ≤ 0.5)

A series of Ni-Zn ferrite with compositional formula Ni{sub 1-x}Zn{sub x}Fe{sub 2}O{sub 4} (0.0 ≤ x ≤ 0.5) were prepared by solid-state reaction route. The influence of the Zn content on the structural and dielectric properties of NiFe{sub 2}O{sub 4} was investigated using X-ray powder diffraction (XRD), Raman spectroscopy and dielectric measurements. XRD analysis reveals that the samples are polycrystalline single-phase cubic spinel in structure excluding the presence of any secondary phase corresponding to any structure. Slight variation in the lattice parameter of Zn doped NiFe{sub 2}O{sub 4} has been observed due to difference in ionic radii of cations. Raman analysis reveals the doublet like nature of A{sub 1g} mode for all synthesized samples. Small shift in Raman modes and increment in the line width has been observed with the doping ions. Furthermore, room temperature dielectric properties of all the prepared samples have been reported. It is observed that for each sample the dielectric constant decreases with an increase of frequency and becomes constant at higher frequencies.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of antimony concentration on structural and transport properties of (Bi{sub 1-x}Sb{sub x}){sub 2}Te{sub 3} mixed crystal

Polycrystalline (Bi{sub 1-x}Sb{sub x}){sub 2}Te{sub 3} (0.60≤x≤0.68) alloys have been synthesized by solid state reaction method. Structural characterizations have been done using X-Ray Diffraction (XRD). Lattice parameter decreases with antimony (Sb) concentration. Sb doping leads to the modification in band structure and Fermi surface geometry. Band gap calculated from thermal variation of resistivity (ρ-T) data, decreases with Sb concentration. Sb concentration dependent power factor near room temperature have been calculated from obtained resistivity and thermopower data. Highest power factor obtained for (Bi{sub 0.40}Sb{sub 0.60}){sub 2}Te{sub 3} alloy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Co doping on structural, optical, magnetic and dielectric properties of Bi{sub 2}Fe{sub 4}O{sub 9}

Polycrystalline Bi{sub 2}Fe{sub 4}O{sub 9} and 2% Co doped Bi{sub 2}Fe{sub 4}O{sub 9} were prepared by solid state reaction route. X-ray diffraction (XRD) result reveals that there is no change in the crystal structure due to Co doping and the compound has orthorhombic structure. UV-visible spectroscopy confirms the decrease in band gap due Co doping. Zero field cooled magnetization measurement at 100 Oe magnetic field shows substantial decrease in the magnetic transition temperature. Room temperature frequency dependent dielectric permittivity at 1V DC bias shows ∼10% increase in Co doped sample with respect to pure Bi{sub 2}Fe{sub 4}O{sub 9}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of dopent on the structural and optical properties of ZnS thin film as a buffer layer in solar cell application

In order to find the suitable alternative of toxic CdS buffer layer, deposition of pure ZnS and doped with Al by chemical bath deposition method have been reported. Further as grown pure and doped thin films have been annealed at 150°C. The structural and surface morphological properties have been characterized by X-Ray diffraction (XRD) and Atomic Force Microscope (AFM).The XRD analysis shows that annealed thin film has been polycrystalline in nature with sphalerite cubic crystal structure and AFM images indicate increment in grain size as well as growth of crystals after annealing. Optical measurement data give band gap of 3.5 eV which is ideal band gap for buffer layer for solar cell suggesting that the obtained ZnS buffer layer is suitable in a low-cost solar cell.

36 MATERIALS SCIENCE↗

Effect of xenon on the structural phase state of the surface layer of cemented carbide under pulsed electron-beam irradiation

A comparative analysis of the surface-layer microstructure of a tungsten-based cemented carbide modified with pulsed high-energy electron beams generated by gas-discharge plasmas and of the tool life of metal-cutting plates prepared from this alloy is performed. The choice of a plasma-forming gas providing for the emission of electrons out of the plasma-filled cathode is shown to have a profound influence both on the formation process of nano-sized structural-phase states in the surface layer of the cemented carbide and on the tool life of the metal-cutting plates prepared from this alloy.

36 MATERIALS SCIENCE↗

Laser-driven high-energy-density deuterium and tritium ions for neutron production in a double-cone configuration

By using two-dimensional particle-in-cell simulations, we investigate laser-driven ion acceleration and compression from a thin DT foil in a double-cone configuration. By using two counterpropagating laser pulses, it is shown that a double-cone structure can effectively guide, focus, and strengthen the incident laser pulses, resulting in the enhanced acceleration and compression of D{sup +} and T{sup +}. Due to the ion Coulomb repulsion and the effective screening from the external laser electric fields, the transverse diffusion of ions is significantly suppressed. Finally, the peak energy density of the compressed ions exceeds 2.73 × 10{sup 16 }J/m{sup 3}, which is about five orders of magnitude higher than the threshold for high energy density physics, 10{sup 11 }J/m{sup 3}. Under this condition, DT fusion reactions are initiated and the neutron production rate per volume is estimated to be as high as 7.473 × 10{sup 35}/m{sup 3} s according to Monte Carlo simulations. It is much higher than that of the traditional large neutron sources, which may facilitate many potential applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Broadband ultra-high transmission of terahertz radiation through monolayer MoS{sub 2}

In this study, the terahertz (THz) absorption and transmission of monolayer MoS{sub 2} with different carrier concentrations were investigated theoretically. The calculation shows that the THz absorption of monolayer MoS{sub 2} is very low even under high carrier concentrations and large incident angles. The sum of reflection and absorption losses of monolayer MoS{sub 2} is lower than that of graphene by one to three orders of magnitude. The transmission of monolayer MoS{sub 2} is higher than that of two-dimensional electron gases in traditional GaAs and InAs. The field-effect tube structure formed by monolayer MoS{sub 2}-insulation-layer-graphene is also studied. The THz absorption of graphene can reach saturation under low voltage by tuning the voltage between MoS{sub 2} and graphene layers in the structure. The maximum THz absorption of monolayer MoS{sub 2} is approximately 5%. Thus, monolayer MoS{sub 2} is a promising candidate for THz transparent electrodes.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of sintering temperature on structural and dielectric properties of Bi and Li co-substituted SrTiO{sub 3}

Sintering is an important factor that affects the microstructure development in ceramics. In this work, Bi and Li co-substituted Strontium Titanate (ST) ceramics samples sintered at different temperatures are prepared and analyzed by X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). XRD was used to detect phase structure of the sintered samples and SEM was used for microstructure analysis. Dielectric properties of Bi and Li co-substituted SrTiO{sub 3} samples were measured using Agilent 4294A Impedance analyzer in the frequency range 40 Hz to 5 MHz at room temperature. The result reveals that the dielectric constant of Bi and Li co-substituted SrTiO{sub 3} ceramics increases with increasing sintering temperature up to 1250°C and then decreases beyond that. The highest value of dielectric constant obtained is 860 at 1KHz frequency and lowest dielectric loss observed is 0.04 at the same frequency for samples sintered at 1250°C. Also the grain size increases with increase of sintering temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of curvature on the structural and magnetic properties of Ni film deposited on self-assembled nanospheres

Important experimental findings and their impact on physical properties of Ni thin film are presented with the focus on structural and magnetic property investigations. For this purpose, Ni film (40 nm) was deposited on polystyrene nanospheres (PS, diameter 800 nm) using electron beam evaporation technique simultaneously with a similar reference film on plane Si substrate. The structural properties of the films measured using XRD technique show nanocrystalline growth of Ni on both size PS spheres with an average grain size of ∼ 78 nm, while high crystallinity was observed in the film deposited onto plane Si substrate. A lower coercivity (9 mT) was observed in the Ni/(800 nm) PS as compared to the film deposited on 530 nm PS (23 mT) (our earlier study) and Ni/Si (20 mT). The observed changes in structural and magnetic properties are attributed to the curvature induced modifications at atomic level.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of annealing on the structural and optical properties of TiO{sub 2} powder prepared by sol-gel route

Using titanium isopropoxide as the precursor, Titanium dioxide (TiO{sub 2}) powder was synthesized via sol-gel method, a promising low temperature route for preparing nanosized metal oxide semiconductors with good homogeneity at low cost. The as-prepared nano powder was thermally treated in air at 550, 650, 750, 900 and 1100°C for 1hr after drying at room temperature and used for further characterization. X-ray diffraction measurements showed that the annealing treatment has a strong impact on the crystal phase of TiO{sub 2} samples. The crystallite size as calculated from Debye Scherer formula lies in the range 29-69 nm and is found to increase with increase in annealing temperature. Photoluminescence studies exhibit an improvement in the optical efficiency of the samples with post synthesis heat treatment. Annealing at temperature above 900°C results in a degradation of the structural and optical quality of the TiO{sub 2} nano powder samples.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of annealing on the structure of chemically synthesized SnO{sub 2} nanoparticles

Tin oxide (SnO{sub 2}) nanoparticles have been synthesized by co-precipitation method. The synthesized nanoparticles were characterized by X-ray diffraction (XRD) and Raman spectroscopy. XRD analysis confirmed the single phase formation of SnO{sub 2} nanoparticles. The Raman shifts showed the typical feature of the tetragonal phase of the as-synthesized SnO{sub 2} nanoparticles. At low annealing temperature, a strong distortion of the crystalline structure and high degree of agglomeration was observed. It is concluded that the crystallinity of SnO{sub 2} nanoparticles improves with the increase in annealing temperature.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effect of film thickness on structural and mechanical properties of AlCrN nanocompoite thin films deposited by reactive DC magnetron sputtering

In this study, the influence of film thickness on the structural, surface morphology and mechanical properties of Aluminum chromium nitride (AlCrN) thin films has been successfully investigated. The AlCrN thin films were deposited on silicon (100) substrate using dc magnetron reactive co-sputtering at substrate temperature 400° C. The structural, surface morphology and mechanical properties were studied using X-ray diffraction, field-emission scanning electron microscopy and nanoindentation techniques respectively. The thickness of these thin films was controlled by varying the deposition time therefore increase in deposition time led to increase in film thickness. X-ray diffraction pattern of AlCrN thin films with different deposition time shows the presence of (100) and (200) orientations. The crystallite size varies in the range from 12.5 nm to 36.3 nm with the film thickness due to surface energy minimization with the higher film thickness. The hardness pattern of these AlCrN thin films follows Hall-Petch relation. The highest hardness 23.08 Gpa and young modulus 215.31 Gpa were achieved at lowest grain size of 12.5 nm.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effect of cobalt doping on structural, optical and dielectric properties of TiO{sub 2}

A diluted magnetic semiconductor (DMS) Co-doped TiO{sub 2} is studied here for dielectric properties. Undoped and Co-doped TiO{sub 2} samples were prepared by sol-gel method. The formation of anatase phase has been investigated by X-ray diffraction (XRD). UV-Vis absorption spectra show that the incorporation of Co into the TiO{sub 2} lattice leads to redshift in the optical response, as well as lowering the band gap energy. The defect oriented emissions were seen from photoluminescence (PL) study. The dielectric properties of pure and Co-doped TiO{sub 2} samples were studied in the frequency range of 10 Hz to 10 MHz at different temperatures. Doped sample exhibit low dielectric constant when compared with host system. Both dielectric constant and ac conductivity increases with temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Cr doping on structural and magnetic properties of ZnS nanoparticles

The structural, optical and magnetic properties of pure and Cr doped ZnS nanoparticles were studied at room temperature. X-ray diffraction analysis confirmed the absence of any mixed phase and the cubic structure of ZnS in pure and Cr doped ZnS nanoparticles. Fourier transfer infrared spectra confirmed the Zn-S stretching bond at 664 cm{sup −1} of ZnS in all prepared nanoparticles. The UV-Visible absorption spectra showed blue shift which became even more pronounced in Cr doped ZnS nanoparticles. However, at relatively higher Cr concentrations a slower red shift was shown by the doped nanoparticles. This phenomenon is attributed to sp-d exchange interaction that becomes prevalent at higher doping concentrations. Further, magnetic hysteresis measurements showed that Cr doped ZnS nanoparticles exhibited ferromagnetic behavior at room temperature.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effect of cobalt doping on structural and optical properties of ZnO nanoparticles

Cobalt doped ZnO nanoparticles of uniform sizes were prepared by a chemical method using ZnCl{sub 2} and NaOH as the source materials. The formation of Co-doped ZnO nanoparticles was confirmed by transmission electron microscopy (TEM), high resolution TEM (HR-TEM) and selected area electron diffraction (SAED) studies. The optical properties of obtained products were examined using room temperature UV-visible and FTIR spectroscopy. SAED of cobalt doped ZnO nanoparticles shows homogeneous distribution of nanoparticles with hexagonal structure. The HRTEM image of the Co-doped ZnO nanoparticles reveals a clear lattice spacing of 0.52 nm corresponding to the interplanar spacing of wurtzite ZnO (002) plane. The absorption band at 857 cm{sup −1} in FTIR spectra confirmed the tetrahedral coordination of Zn and a shift of absorption peak to shorter wavelength region and decrease in absorbance with Co doping.is observed in UV-Visible spectra.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Thermoluminescence characteristics of LiF: Cu nanocrystalline phosphor

Copper (Cu) activated LiF phosphor in nanocrystalline form has been prepared by the chemical co-precipitation method for radiation dosimetry application. The formation of nanocrystalline structure has been confirmed by X-ray diffraction and Scanning electron microscopy. Cubical shaped nanostructure with average particle size of 33nm has been formed. The sample was prepared at different concentration of Cu from 0.01mol% to 3 mol%. TL properties were investigated by studying the glow curve after irradiating the phosphor to gamma ray Co{sup 60} source with dose of 15 Gy. It has been found that nanocrystalline LiF: Cu show simple glow curve structure with a single glow peak at 404 K where as commercially available phosphors exhibits multi peak complex glow curve structure. The effect of different normality on the TL properties of phosphor has been studied. Maximum TL intensity for LiF: Cu (0.1mol %) phosphor is observed at the normality of 0.5N and annealing temperature of 200°C. The phosphor showed good linearity up to 10 KGy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of bath temperature on structure, morphology and thermoelectric properties of CoSb{sub 3} thin films

CoSb{sub 3} thin films are deposited on conducting glass substrates (FTO) by electrodeposition at different bath temperatures (60°C, 70°C and 80°C) and the resulting influence of the bath temperature on the structure, morphology and electrical properties of films is investigated. X-ray diffraction confirms the formation of CoSb{sub 3} phase in the films. Scanning electron microscopy reveals that different morphologies ranging from branched nano-flakes to nano-needles evolve as bath temperature increases. It is concluded that a growth temperature of 80°C is suitable for producing CoSb{sub 3} films with such properties that show potential feasibility for thermoelectric applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗