Search NASA⌕ Search

SEARCH · Search NASA

Results for “Basis for Development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

Developing Waste-Driven Design Requirements for Filtration and Ion-Exchange at the Hanford LAWPS Facility - 16394

The United States Department of Energy is building the Low Activity Waste Pretreatment System (LAWPS) at the Hanford site near Richland, Washington to treat liquid tank waste. The primary unit operations are filtration for solids removal and ion-exchange for cesium-137 removal. The properties of the stored waste are diverse, therefore the design requirements need to allow for a variety of feeds from the Hanford tank farms. However, it is not cost effective to allow a few rare feeds to define the requirements when there are other options for treating the rare wastes. The waste-derived design requirements were based on trends from this data. The primary feed requirements that will drive filtration and ion-exchange performance are solids content of the feed, cesium to sodium ratio, and potassium concentration. Additionally, aluminum and total organic carbon (TOC) concentrations are considered for flammable gas generation. For the cesium and potassium concentrations, the available experimental data was collected, sorted, and compared against the historic requirements. The design basis for cesium and potassium feed parameters developed here enveloped all but a couple outlier tanks. A review of available grab sample data indicates that occasionally the samples would have up to 0.8 wt% solids concentration. One single sample had 3.3 wt% solids concentration. These solids concentrations were assigned as the nominal and upper bounding solids concentrations. Flammable gas generation does not directly impact the ion exchange process throughput but does impact the design safety requirements, thus TOC and aluminum concentrations (which are inputs to the flammable gas calculations) were examined in a similar way, but were paired together through a simplified correlation to reach an upper bounding value of 0.6 wt% TOC*Al{sup 0.4}. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

U.S. department of energy safety design strategy review and approval beyond critical decision 3 for the high-level waste facility - 15525

The Waste Treatment and Immobilization Plant (WTP) in Hanford, Washington, is the nation's largest environmental remediation construction project. In 2012, at the WTP's High-Level Waste (HLW) Facility, the U.S. Department of Energy (DOE), Office of River Protection (ORP) restricted construction work at the Hazard Category 2 nuclear facility because of unresolved technical issues associated with the facility and of misalignment of the design and nuclear safety basis. By 2013, as additional issues were discovered, ORP limited HLW design and procurement activities. Addressing the technical issues and the misalignment of the design basis with the Preliminary Documented Safety Analysis (PDSA) is a priority for ORP. A proposal was developed to use the concept of a safety design strategy (SDS), as documented in DOE-STD-1189-2008, Integration of Safety into the Design Process, as a planning mechanism to support facility design and PDSA alignment. The standard provides the processes to develop an SDS that will ensure safety is integrated into design early in the project, by the start of preliminary design. Ultimately, as design progresses, an SDS is intended to support development of the project's PDSA. However, in this unique case, the HLW Facility design and construction phase has progressed beyond Critical Decision 3 and DOE-STD-1189-2008 was issued in 2008; 6 years after ORP approved the first WTP PDSA. In July 2013, ORP and the contractor recognized that the unresolved technical issues and design - safety basis misalignment should be addressed through a renewed look at nuclear safety requirements, and agreed that developing an SDS tailored to the criteria in DOE-STD-1189-2008 provided the best path forward to better integrate design and safety. Development of the SDS for the HLW Facility was one of many goals ORP established in a plan that describes how ORP will determine whether, and under what conditions, the contractor should be authorized to proceed with production engineering, procurement, and construction activities for the HLW Facility. Over the next several months, the contractor developed the draft SDS, identifying design basis accidents and control strategies for those accidents. ORP monitored progress and, when appropriate, provided recommendations. In April 2014, the contractor provided a draft SDS to ORP for initial review by an independent DOE Review Team. The Review Team was comprised of representatives from nuclear safety, criticality safety, engineering, fire protection, the Office of Environmental Management, the Assistant Manager WTP, and the DOE Chief of Nuclear Safety. A unique draft document review and interactive review process, facilitated through work sessions and continuous communication with the contractor, culminated in the development of 147 technical comments on topics varying from SDS implementation to hydrogen deflagration in vessels. Comment resolution sought to improve project clarity, delineation of control strategies, and, holistically, facilitate integration of safety into design in the SDS, as it will guide the restart of the HLW Facility production engineering and limited procurement and construction activities. All comments were resolved in support of a contractor submission of the final SDS to ORP at the end of June 2014. Successful resolution of these comments was achieved by continuing the real-time response and incorporation interaction with the contractor to ensure that mutual objectives were satisfied. The response times were facilitated through telephone, E-mail, and a shared file server accessible to contractor and DOE reviewers across the DOE complex. As a measure of success of this process, the Safety Basis Approval Authority (ORP Manager) and the WTP Federal Project Director approved the SDS on August 1, 2014, with no conditions of approval. DOE and the contractor recognized that it would be difficult to implement the SDS without changes to the existing contractor's engineering and nuclear safety processes. Accordingly, the contractor developed or revised a significant number of engineering and nuclear safety plans and procedures to implement the SDS into the design process. Over the coming year, the contractor will conduct a gap analysis between the SDS and the presently approved PDSA to incorporate the design basis accidents and preferred control strategies developed from the SDS into the PDSA. In addition, ORP will conduct an assessment of the contractor's implementation of the SDS into the design process at the appropriate stage of implementation, within 6 to 12 months of approval. Although the SDS was developed late in the HLW project timeline, the document will facilitate alignment of design and the safety basis, and is a key step in the return to full production engineering for the HLW Facility. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

V-band IMPATT power amplifier

This program is the result of the continuing demand and future requirement for a high data rate 60-GHz communications link. A reliable solid-state transmitter which delivers the necessary power over a wide bandwidth using the present IMPATT diode technology required the development of combining techniques. The development of a 60-GHz IMPATT power combiner amplifier is detailed. The results form a basis from which future wideband, high-power IMPATT amplifiers may be developed. As a result, several state-of-the-art advancements in millimeter-wave components technology were achieved. Specific achievements for the amplifier integration were: development of a nonresonant divider/combiner circuit; reproducible multiple junction circulator assemblies; and reliable high power 60-GHz IMPATT diodes. The various design approaches and tradeoffs which lead to the final amplifier configuration are discussed. A detailed circuit design is presented for the various amplifier components, and the conical line combiner, radial line combiner, and circulator development are discussed. The performance of the amplifier, the overall achievement of the program, the implications of the results, and an assessment of future development needs and recommendations are examined.

Schell, S. W.↗

2021 Component Innovation Awardee: Windurance, LLC

Distributed wind turbine manufacturers seeking to enter the market are often hampered by two challenges: not enough capital and no specific expertise in developing certified electronic equipment. A harsh reality is that off-the-shelf power electronics are neither certified nor cost-effective. This lack of certified controller equipment in the distributed wind energy industry adds expense and impedes market penetration related to certification for individual wind turbines, wind system projects, and installations. Normally, these certification costs would be borne repeatedly by individual turbine manufacturers or developers on a model-by-model or project-by-project basis, resulting in cost and time delays as well as uncertainty and risk for project developers and prospective owners. Windurance seeks to eliminate these challenges by developing and obtaining third-party certification of a standardized wind turbine controller. This will facilitate development, certification, and production while supporting efficiencies not easily achievable by individual manufacturers. Windurance's Distributed Wind Industry Turbine Controller will enable manufacturers to apply proprietary turbine- specific configurations and functionality. When applicable, manufacturers can expand on a Windurance-provided software framework to add unique or proprietary functionality.

CIP↗

Post-Fukushima Safety Enhancement Activities in Canada

In the immediate aftermath of the common-cause seismic and tsunami events that triggered the Fukushima Daiichi nuclear accident on March 11, 2011, the nuclear regulator, the Canadian Nuclear Safety Commission (CNSC), requested that all Cass I nuclear facilities re-examine the safety cases for their nuclear facilities. Lessons-learned task forces were established by the CNSC, and the nuclear utilities, Ontario Power Generation (OPG), Bruce Power (BP), and New Brunswick Power (NBP). The purposes of these independent task forces was to develop relevant lessons learned issues for the Candu nuclear power plants operating in Canada and to identify actions that could enhance safety. Subsequently, a CNSC Integrated Action Plan was developed to address the recommendations arising from the CNSC Task Force Report, and the licensees aligned their actions with this plan. The actions were grouped into four categories, as follows. 1. Strengthening defence in depth; Actions included re-assessment of a site-specific external hazards using PSA; physical plant changes to add further cooling water make-up capability to heat sinks; development of new Canadian standards and updated regulatory documents that address requirements for Beyond Design Basis Accidents (BDBA), Probabilistic Safety Assessment (PSA) and Period Safety Review (PSR); development of a new and novel methodology for assessing multi-unit risk that is consistent with the IAEA construct of defence-in-depth (including a safety goal hierarchy and complementary risk analysis methods that address 'Black Swan' events); enhanced management of hydrogen combustion challenges; and enhanced Severe Accident Management Guidelines (SAMG). 2. Enhancing emergency response; Actions included provision of Emergency Mitigation Equipment (EME) such as transportable diesel-driven pumps or fire engines, transportable diesel generators for AC and instrument power; pre-installed connections to in-plant equipment via easily accessible and protected quick-connect points for water and electrical power; upgraded emergency response centres; enhanced communication systems and protocols; and enhanced emergency response programs, training and exercises. 3. Improving the regulatory framework and processes; 4. Enhancing international collaboration. Actions assigned under categories 3 and 4 were placed upon the regulator. This presentation will focus on the assigned actions in categories 1 and 2. The underlying motivation, objectives, and safety benefits associated with the actions will be described within the context of broader aspects of severe accident mitigation in water-cooled reactors. (author)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Supporting resilience in nuclear power plant operations - conceptual frames for human factors development and validation - 166

This is a summary paper of conceptual developments on nuclear power plant operation by the human factors team at VTT Technical Research Centre of Finland. While drawing together years of studies, the paper also discusses recent progresses in training development. Firstly, there is a long background in work analysis and system validation. The analysis model applied provides a model for assessing and identifying 'core-task functions,' that is, basic functions that should be fulfilled within work activity. Secondly, we have evaluated the existing training practices at a Finnish plant and identified challenges that could be generally prevalent in the nuclear domain - they seem to reflect the hierarchical and safety-critical nature of NPP operation. In terms of potential solutions, we are currently testing and developing some new self-evaluation and self-confrontation methods. First and foremost, however, we discuss the common theory basis for our research approaches. On the broadest level, our development and research work reflects the view of safety as expressed by resilience engineering literature: safety is not seen merely as 'negative' lack of mistakes, but also as 'positive' capability to solve and anticipate problems. For example, it is assumed that operators' capability for situational interpretation should be supported at all times: even if the emergency procedures dictate operator activity specifically, the operators should understand the influence of the operating procedures for the plant process and system state. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

A Theory for Stability and Buzz Pulsation Amplitude in Ram Jets and an Experimental Investigation Including Scale Effects

From a theory developed on a quasi-one-dimensional-flow basis, it is found that the stability of the ram jet is dependent upon the instantaneous values of mass flow and total pressure recovery of the supersonic diffuser and immediate neighboring subsonic diffuser. Conditions for stable and unstable flow are presented. The theory developed in the report is in agreement with the experimental data of NACA-TN-3506 and NACA-RM-L50K30. A simple theory for predicting the approximate amplitude of small pressure pulsation in terms of mass-flow decrement from minimum-stable mass flow is developed and found to agree with experiments. Cold-flow tests at a Mach number of 1.94 of ram-jet models having scale factors of 3.15:1 and Reynolds number ratios of 4.75:1 with several supersonic diffuser configurations showed only small variations in performance between geometrically similar models. The predominant variation in steady-flow performance resulted from the larger boundary layer in the combustion chamber of the low Reynolds number models. The conditions at which buzz originated were nearly the same for the same supersonic diffuser (cowling-position angle) configurations in both large and small diameter models. There was no appreciable variation in stability limits of any of the models when the combustion-chamber length was increased by a factor of three. The unsteady-flow performance and wave patterns were also similar when considered on a reduced-frequency basis determined from the relative lengths of the model. The negligible effect of Reynolds number on stability of the off-design configurations was not anticipated in view of the importance of boundary layer to stability, and this result should not be construed to be generally applicable. (author)

Trimpi, Robert L↗

Improving scalability of electronic structure code for molecular simulations in the presence of environment

A scalable density functional electronic code with Gaussian basis set, called UTEP-NRLMOL, is developed to perform simulations of molecular systems in the presence of the environment with particular attention to the memory requirements. In the electronic structure calculations, the memory and computation time are proportional to the number of atoms. Memory requirements for density functional calculations scale as N*N, where N is the number of atoms. While the recent advances in HPC offer platforms with large numbers of cores, the limited amount of memory available on a given node and poor scalability of the electronic structure codes hinder their efficient usage of these platforms. We have introduced new scaling and parallelization paradigms using MPI-3 shared-memory functionality combined with usage of sparse algebra and storage of matrices in sparse format. This extends the range of applicability of the UTEP-NRLMOL code to large systems over 10,000 atoms, or using up to 67,000 basis functions, and making use of HPC architectures using over 6,000 processors utilizing all available cores. We have also interfaced code with effective fragment potential and polarizable continuum model libraries. The code was used in simulations of several applications which are published in reputed scientific journals.

74 ATOMIC AND MOLECULAR PHYSICS↗

Improved Algorithm For Finite-Field Normal-Basis Multipliers

Improved algorithm reduces complexity of calculations that must precede design of Massey-Omura finite-field normal-basis multipliers, used in error-correcting-code equipment and cryptographic devices. Algorithm represents an extension of development reported in "Algorithm To Design Finite-Field Normal-Basis Multipliers" (NPO-17109), NASA Tech Briefs, Vol. 12, No. 5, page 82.

Wang, C. C.↗

Low-Temperature Projects of the Department of Energy's Geothermal Technologies Program: Evaluation and Lessons Learned

This paper discusses opportunities and challenges related to the technical and economic feasibility of developing power generation from geothermal resources at temperatures of 150 degrees C and lower. Insights from projects funded by the U.S. Department of Energy (DOE), Geothermal Technologies Office inform these discussions and provide the basis for some lessons learned to help guide decisions by DOE and the industry in further developing this resource. The technical basis for low-temperature geothermal energy is well established and the systems can be economic today in certain situations. However, these applications are far from a 'plug and play' product; successful development today requires a good knowledge of geothermal system design and operation.

15 GEOTHERMAL ENERGY↗

Low-Temperature Projects of the Department of Energy's Geothermal Technologies Program: Evaluation and Lessons Learned: Preprint

This paper discusses opportunities and challenges related to the technical and economic feasibility of developing power generation from geothermal resources at temperatures of 150 degrees C and lower. Insights from projects funded by the U.S. Department of Energy (DOE), Geothermal Technologies Office inform these discussions and provide the basis for some lessons learned to help guide decisions by DOE and the industry in further developing this resource. The technical basis for low-temperature geothermal energy is well established and the systems can be economic today in certain situations. However, these applications are far from a 'plug and play' product; successful development today requires a good knowledge of geothermal system design and operation.

15 GEOTHERMAL ENERGY↗

DOE-GTO Low Temperture Projects Evaluation and Lessons Learned

This paper discusses opportunities and challenges related to the technical and economic feasibility of developing power generation from geothermal resources at temperatures of 150 degrees C and lower. Insights from projects funded by the U.S. Department of Energy (DOE), Geothermal Technologies Office inform these discussions and provide the basis for some lessons learned to help guide decisions by DOE and the industry in further developing this resource. The technical basis for low-temperature geothermal energy is well established and the systems can be economic today in certain situations. However, these applications are far from a 'plug and play' product; successful development today requires a good knowledge of geothermal system design and operation.

15 GEOTHERMAL ENERGY↗

Imaging spectrometers for terrestrial and planetary remote sensing - A progress report

Attention is given to two major design approaches, the 'whiskbroom' and the 'pushbroom', in the present consideration of imaging spectroscopy for both planetary and terrestrial missions. A near-IR mapping spectrometer has been developed for the Galileo Jupiter Orbiter Mission; on the basis of this design, and incorporating focal plane array technology improvements, a family of imaging spectrometers exemplified by the Visual and IR Mapping Spectrometer is under development for other planetary missions.

Wellman, John B.↗

An efficient reconstruction algorithm for diffusion on triangular grids using the nodal discontinuous Galerkin method

High-energy-density (HED) hydrodynamics studies such as those relevant to inertial confinement fusion and astrophysics require highly disparate densities, temperatures, viscosities, and other diffusion parameters over relatively short spatial scales. This presents a challenge for high-order accurate methods to effectively resolve the hydrodynamics at these scales, particularly in the presence of highly disparate diffusion. A significant volume of engineering and physics applications use an unstructured discontinuous Galerkin (DG) method developed based on the finite element mesh generation and algorithmic framework. This work discusses the application of an affine reconstructed nodal DG method for unstructured grids of triangles. Solving the diffusion terms in the DG method is non-trivial due to the solution representations being piecewise continuous. Hence, the diffusive flux is not defined on the interface of elements. The proposed numerical approach reconstructs a smooth solution in a parallelogram that is enclosed by the quadrilateral formed by two adjacent triangle elements. The interface between these two triangles is the diagonal of the enclosed parallelogram. Similar to triangles, the mapping of parallelograms from a physical domain to a reference domain is an affine mapping, which is necessary for an accurate and efficient implementation of the numerical algorithm. Thus, all computations can still be performed on the reference domain, which promotes efficiency in computation and storage. This reconstruction does not make assumptions on choice of polynomial basis. Reconstructed DG algorithms have previously been developed for modal implementations of the convection–diffusion equations. However, to the best of the authors’ knowledge, this is the first practical guideline that has been proposed for applying the reconstructed algorithm on a nodal discontinuous Galerkin method with a focus on accuracy and efficiency. As a result, the algorithm is demonstrated on a number of benchmark cases as well as a challenging substantive problem in HED hydrodynamics with highly disparate diffusion parameters.

Computational efficiency↗

Anisotropic excitonic magnetism from discrete C 4 symmetry in CeRhIn 5

Anisotropy in strongly correlated materials is a central parameter in determining the electronic ground state and is tuned through the local crystalline electric field. This is notably the case in the CeCo x Rh 1 − x In 5 system where the ground-state wave function can provide the basis for antiferromagnetism and/or unconventional superconductivity. We develop a methodology to understand the local magnetic anisotropy and experimentally investigate with neutron spectroscopy applied to antiferromagnetic ( T N = 3.8 K ) CeRhIn 5 , which is isostructural to d -wave superconducting ( T c = 2.3 K ) CeCoIn 5 . Through diagonalizing the local crystal field Hamiltonian with discrete tetragonal C 4 point group symmetry and coupling these states with the random phase approximation, we find two distinct modes polarized along the crystallographic c and a − b planes, agreeing with experiment. The anisotropy and bandwidth, underlying the energy scale of these modes, are tuneable with a magnetic field which we use experimentally to separate in energy single and multiparticle excitations thereby demonstrating the instability of excitations polarized within the crystallographic a − b plane in CeRhIn 5 . We compare this approach to a S eff = 1 2 parametrizations and argue for the need to extend conventional SU(2) theories of magnetic excitations to utilize the multilevel nature of the underlying crystal-field basis states constrained by the local point-group C 4 symmetry. Published by the American Physical Society 2024

Brener, D. J. (ORCID:0000000333400177)↗

Continuous Efforts to Develop the National System for Material Control and Accounting Training at the George Kuzmycz Training Center

The George Kuzmycz Training Center (GKTC) for Physical Protection, Control and Accounting of Nuclear Materials was established in 1998 at the Kyiv Institute of Nuclear Research of the Ukrainian Academy of Sciences through the collaborative efforts of the United States and Ukraine. Later the European Commission (EC) joined the US in assisting with the Material Control and Accounting (MC&A) part of the GKTC training program. The Government of Ukraine designated the GKTC as the National Center responsible for providing training and methodological support for nuclear facilities and nuclear specialists in the Material Protection, Control and Accounting (MPC&A) area. To increase the efficiency of the State MC&A system an essential number of new regulations, norms and rules have been developed; some of them mandate regular and more intensive training of MC&A specialists in the industry - from those working at the Nuclear Regulatory Authority of Ukraine to the personnel of nuclear facilities. To meet such regulations GKTC plans to develop next year a number of training courses under the EC contract; such courses will reflect both the specifics of Ukrainian nuclear facilities and the level of expertise of the facilities’ personnel. The NDA training laboratory, established in 2003 with US DOE financial support and technical and methodological assistance, considerably expanded the GKTC’s training capabilities for MC&A programs. Next year that lab will be supplemented with a new NM Surveillance and Containment laboratory as current plans call for under the EC contract. The US DOE is also providing funding to support that project. Under the EC contract the laboratory will be equipped with state-of-the-art, advanced surveillance and containment equipment which will strengthen and expand even further the GKTC’s training capabilities and potential. This will allow GKTC to train Ukrainian nuclear industry specialists in practically all MC&A topics. Furthermore, GKTC is planning to offer already this year and to continue offering in the future, on a regular basis, the courses that have already been developed, while continuing to develop new ones. This paper briefly describes the work done to upgrade the Ukrainian MC&A system, both at the State and at the facilities’ levels, as well as the results of efforts to develop the National System for training MC&A personnel at the GKTC. It also describes problems encountered and their solution; it includes comments, suggestions and recommendations for future activities to promote and improve the nuclear material management culture in Ukraine.

Gavrilyuk, Victor I.↗

Iterative diagonalization of the non-Hermitian transcorrelated Hamiltonian using a plane-wave basis set: Application to sp-electron systems with deep core states

We develop an iterative diagonalization scheme in solving a one-body self-consistent-field equation in the transcorrelated (TC) method using a plane-wave basis set. Non-Hermiticity in the TC method is well handled with a block-Davidson algorithm. We verify that the required computational cost is efficiently reduced by our algorithm. In addition, we apply our plane-wave-basis TC calculation to some simple sp-electron systems with deep core states to elucidate an impact of the pseudopotential approximation to the calculated band structures. We find that a position of the deep valence bands is improved by an explicit inclusion of core states, but an overall band structure is consistent with a regular setup that includes core states into the pseudopotentials. This study offers an important understanding for the future application of the TC method to strongly correlated solids.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗