Search NASA⌕ Search

SEARCH · Search NASA

Results for “Component amounts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

Determination of alloy content from plume spectral measurements

The mathematical derivation for a method to determine the identities and amounts of alloys present in a flame where numerous alloys may be present is described. This method is applicable if the total number of elemental species from all alloys that may be in the flame is greater than or equal to the total number of alloys. Arranging the atomic spectral line emission equations for the elemental species as a series of simultaneous equations enables solution for identify and amount of the alloy present in the flame. This technique is intended for identification and quantification of alloy content in the plume of a rocket engine. Spectroscopic measurements reveal the atomic species entrained in the plume. Identification of eroding alloys may lead to the identification of the eroding component.

Madzsar, George C.↗

Diffuse gamma-ray emission from pulsars in the Large Magellanic Cloud

We investigate the contribution of pulsars to the diffuse gamma-ray emission from the LMC. The pulsar birth rate in the LMC is a factor of about 10 lower than that of the Galaxy and the distance to pulsars in the LMC is about 5-10 times larger than to Galactic pulsars. The resulting total integrated photon flux from LMC pulsars is thus reduced by a factor of about 100 to 1000. However, the surface brightness is not reduced by the same amount because of the much smaller angular extent of the LMC in comparison to the diffuse glow from the Galactic plane. We show that gamma-ray emission due to pulsars born in the LMC could produce gamma-ray fluxes that are larger than the inverse Compton component from relativistic cosmic-ray electrons and a significant fraction of the extragalactic isotropic background or the diffuse Galactic background in that direction. The diffuse pulsar glow above 100 MeV should therefore be included in models of high-energy emission from the LMC. For a gamma-ray beaming fraction of order unity the detected emissions from the LMC constrain the pulsar birth rate to less than one per 50 yr. This limit is about one order of magnitude above the supernova rate inferred from the historic record or from the star-formation rate.

Hartmann, Dieter H.↗

Radiation-Related Risk Analysis for Atmospheric Flight Civil Aviation Flight Personnel

Human data on low dose rate radiation exposure and consequent effects are not readily available, and this fact generates groundtruth concerns for all risk assessment techniques for possible health effects induced by the space radiation environment, especially for long term missions like those foreseen now and in the near future. A large amount of such data may be obtained through civil aviation flight personnel cohorts, in the form of epidemiological studies on delayed health effects induced by the cosmic-ray generated atmospheric radiation environment, a high- LET low dose and low dose rate ionizing radiation with its typical neutron component, to which flight personnel are exposed all throughout their work activity. In the perspective of worldwide studies on radiation exposure of the civil aviation flight personnel, all the available results from previous studies on flight personnel radiation exposure have been examined in various ways (i.e. literature review, meta-analysis) to evaluate possible significant associations between atmospheric ionizing radiation environment and health risks, and to assess directions for future investigations. The physical characteristics of the atmospheric ionizing radiation environment make the results obtained for atmospheric flight personnel relevant for space exploration.

DeAngelis, G.↗

Cosmic Pathways for Compact Groups in the Milli-Millennium Simulation

We detected 10 compact galaxy groups (CGs) at z=0 in the semianalytic galaxy catalog of Guo et al. for themilli-Millennium Cosmological Simulation (sCGs in mGuo2010a). We aimed to identify potential canonicalpathways for compact group evolution and thus illuminate the history of observed nearby CGs. By constructingmerger trees for z=0 sCG galaxies, we studied the cosmological evolution of key properties and compared themwith z=0 Hickson CGs (HCGs). We found that, once sCG galaxies come within 1 (0.5) Mpc of their mostmassive galaxy, they remain within that distance until z=0, suggesting sCG "birth redshifts." At z=0 stellarmasses of sCG most massive galaxies are within 1010M*/Me1011. In several cases, especially in the twofour- and five-member systems, the amount of cold gas mass anticorrelates with stellar mass, which in turncorrelates with hot gas mass. We define the angular difference between group members' 3D velocity vectors,vel, and note that many of the groups are long-lived because their small values of vel indicate a significantparallel component. For triplets in particular, vel values range between 20° and 40° so that galaxies are comingtogether along roughly parallel paths, and pairwise separations do not show large pronounced changes after closeencounters. The best agreement between sCG and HCG physical properties is for M* galaxy values, but HCGvalues are higher overall, including for star formation rates (SFRs). Unlike HCGs, due to a tail at low SFR and M*and a lack of M*1011Me galaxies, only a few sCG galaxies are on the star-forming main sequence

Tzanavaris, Panayiotis↗

Method and apparatus for continuous removal of carbon dioxide vapors from gases

A method for continuously removing carbon dioxide vapor from a carrier gas is disclosed. This method includes, first, causing direct contact of the carrier gas with a liquid mixture in a separation chamber, the carrier gas condensing at a lower temperature than the carbon dioxide vapor. A combination of chemical effects cause the carbon dioxide to condense, complex, or both condense and complex with the liquid mixture. The liquid mixture is chosen from the group consisting of: first, a combination of components that can be maintained in a liquid phase at a temperature below the carbon dioxide vapor's condensation point, whereby the carbon dioxide condenses into the liquid mixture; second, a combination of components where at least one component forms a chemical complex with the carbon dioxide vapor and thereby extracts at least a portion of the carbon dioxide vapor from the carrier gas; and third, a combination of components that can both be maintained in a liquid phase at a temperature below the carbon dioxide's condensation point, and wherein at least one component forms a chemical complex with the carbon dioxide vapor and thereby extracts at least a portion of the carbon dioxide vapor from the carrier gas. The liquid mixture is then reconstituted after passing through the separation chamber by a chemical separation process chosen to remove an equivalent amount of the carbon dioxide vapor from the liquid mixture as was removed from the carrier gas. The reconstituted liquid mixture is restored to temperature and pressure through heat exchange, compression, and expansion, as necessary, in preparation for recycling back to the separation chamber. The liquid mixture is then returned to the separation chamber. In this manner, the carrier gas leaving the exchanger has between 1% and 100% of the carbon dioxide vapor removed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multi-Phased, Post-Accident Support of the Fukushima Dai-Ichi Nuclear Power Plant - 12246

In the wake of the March 11 earthquake and tsunami and the subsequent flooding of several of the Fukushima Dai-Ichi reactors, Japan and the Japanese utility TEPCO faced a crisis situation with incredible challenges: substantial amounts of radioactive mixed seawater and freshwater accumulated in the basements of four reactor and other buildings on the site. This water held varying levels of contamination due to the fact that it had been in contact with damaged fuel elements in the cores and with other contaminated components. The overall water inventory was estimated at around 110,000 tons of water with contamination levels up to the order of 1 Ci/l. Time was of the essence to avoid overflow of this accumulated water into the ocean. AREVA proposed, designed and implemented a water treatment solution using a proven chemical coprecipitation process with ppFeNi reagent, which is currently in use for effluent treatment on several nuclear sites including AREVA sites. In addition to the extremely short schedule the other challenge was to adapt the chemical treatment process to the expected composition of the Fukushima water and, in particular, to evaluate the impact of salinity on process performance. It was also necessary to define operating conditions for the VEOLIA equipment that had been selected for implementation of the process in the future facility. The operation phase began on June 17, and by the end of July more than 30,000 tons of highly radioactive saltwater had been decontaminated - the Decontamination Factor (DF) for Cesium was ∼10{sup 4}. It allowed recycling the contaminated water to cool the reactors while protecting workers and the environment. This paper focuses on the Actiflo{sup TM}-Rad water treatment unit project that was part of the TEPCO general water treatment scheme. It presents a detailed look at the principles of the Actiflo{sup TM}-Rad, related on-the-fly R and D, an explanation of system implementation challenges, and a brief summary of operation results to date. AREVA's response to the Fukushima Dai-Ichi crisis was multi-phased: emergency aid and relief supply was sent within days after the accident; AREVA-Veolia engineering teams designed and implemented a water treatment solution in record time, only 3 months; and AREVA continues to support TEPCO and propose solutions for waste management, soil remediation and decontamination of the Fukushima Dai-Ichi site. Despite the huge challenges, the Actiflo{sup TM}-Rad project has been a success: the water treatment unit started on time and performed as expected. The performance is the result of many key elements: AREVA expertise in radioactive effluents decontamination, Veolia know-how in water treatment equipments in crisis environment, and of course AREVA and Veolia teams' creativity. The project success is also due to AREVA and Veolia teams' reactivity and high level of commitment with engineering teams working 24/7 in Japan, France and Germany. AREVA and Veolia deep knowledge of the Japanese industry ensured that the multi-cultural exchanges were not an issue. Finally the excellent overall project management and execution by TEPCO and other Japanese stakeholders was very efficient. The emergency water treatment was a key step of the roadmap towards restoration from the accident at Fukushima Dai-Ichi that TEPCO designed and keeps executing with success. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

MYBPH inhibits NM IIA assembly via direct interaction with NMHC IIA and reduces cell motility

Highlights: Black-Right-Pointing-Pointer MYBPH inhibits NMHC IIA assembly and cell motility. Black-Right-Pointing-Pointer MYBPH interacts to assembly-competent NM IIA. Black-Right-Pointing-Pointer MYBPH inhibits RLC and NMHC IIA, independent components of NM IIA. -- Abstract: Actomyosin filament assembly is a critical step in tumor cell migration. We previously found that myosin binding protein H (MYBPH) is directly transactivated by the TTF-1 lineage-survival oncogene in lung adenocarcinomas and inhibits phosphorylation of the myosin regulatory light chain (RLC) of non-muscle myosin IIA (NM IIA) via direct interaction with Rho kinase 1 (ROCK1). Here, we report that MYBPH also directly interacts with an additional molecule, non-muscle myosin heavy chain IIA (NMHC IIA), which was found to occur between MYBPH and the rod portion of NMHC IIA. MYBPH inhibited NMHC IIA assembly and reduced cell motility. Conversely, siMYBPH-induced increased motility was partially, yet significantly, suppressed by blebbistatin, a non-muscle myosin II inhibitor, while more profound effects were attained by combined treatment with siROCK1 and blebbistatin. Electron microscopy observations showed well-ordered paracrystals of NMHC IIA reflecting an assembled state, which were significantly less frequently observed in the presence of MYBPH. Furthermore, an in vitro sedimentation assay showed that a greater amount of NMHC IIA was in an unassembled state in the presence of MYBPH. Interestingly, treatment with a ROCK inhibitor that impairs transition of NM IIA from an assembly-incompetent to assembly-competent state reduced the interaction between MYBPH and NMHC IIA, suggesting that MYBPH has higher affinity to assembly-competent NM IIA. These results suggest that MYBPH inhibits RLC and NMHC IIA, independent components of NM IIA, and negatively regulates actomyosin organization at 2 distinct steps, resulting in firm inhibition of NM IIA assembly.

60 APPLIED LIFE SCIENCES↗

Stability of carbon fiber surface chemistry under temperature and its influence on interfacial adhesion with polymer matrices

The thermal stability of the surface chemistry of a surface treated carbon fiber was investigated by X-ray Photoelectron Spectroscopy. Within a range of temperatures from room temperature to 400 C, the only surface functionalities that decomposed were carboxylic acids and dangling nitrogen containing functionalities like amines, amides or nitriles. Significant amounts of water were desorbed as well. This study enabled the testing of the coherence our the fitting of the C(1s), O(1s) and N(1s) peaks. Particularly, when considering the fitting of in the O(1s) peak, carboxylic acids were shown to be included in a single component peak centered at a binding energy of 532.1 eV. The reaction of the carbon fiber surface and an acrylate resin at high temperature, because of the decomposition of carboxylic acids, was highlighted by Differential Scanning Calorimetry. The thermal history of the composite material during its manufacture appeared to be a major influence on the nature of the interactions generated at the fiber-matrix interface and the resulting mechanical properties.

Vautard, Frederic↗

Microwave catalytic conversion of acetylene for co-production of hydrogen and carbon nanotubes

Natural gas conversion to hydrogen and solid carbon can drastically reduce the carbon footprint. Microwave plasma pyrolysis is an emerging process for chemical industries to directly convert methane (CH 4 ), the major component of natural gas, to hydrogen and carbon, which offers benefits such as fast process dynamics, flexibility, and high product yield. However, the formation of unwanted by-products, like acetylene (C 2 H 2 ), will require extra cost for gas separation. Plasma pyrolysis of CH 4 produces large amount of acetylene at downstream, which is currently used mainly for welding. Here, to avoid gas separation and upgrade acetylene from the downstream of methane plasma reactor, a novel approach toward its transformation to carbon nanotubes (CNT) and pure hydrogen (H 2 ) over Ni-based bimetallic catalyst driven by microwave irradiation has been reported in this work. The dominant gas product was hydrogen. Low concentrations of methane, ethane, and ethylene were observed in the product stream. Catalytic acetylene decomposition was carried out at 400 °C over Al 2 O 3 supported Ni catalyst. The results showed that, at 400 °C, acetylene was dehydrogenated to CNT and hydrogen was the dominant gas in product stream over 10Ni-1Pd-Al 2 O 3 catalyst. Characterizations of spent catalysts was conducted using Raman spectroscopy and transmission electron microscopy (TEM) to investigate the properties of carbon deposited over the catalyst during the catalytic acetylene decomposition. The results highlight that methane can be efficiently converted to hydrogen and CNT through 2-step process, microwave plasma and microwave catalytic conversion of intermediate acetylene, operated in a single reactor system driven by microwave.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Phase transformations at interfaces: Observations from atomistic modeling

Here, we review the recent progress in theoretical understanding and atomistic computer simulations of phase transformations in materials interfaces, focusing on grain boundaries (GBs) in metallic systems. Recently developed simulation approaches enable the search and structural characterization of GB phases in single-component metals and binary alloys, calculation of thermodynamic properties of individual GB phases, and modeling of the effect of the GB phase transformations on GB kinetics. Atomistic simulations demonstrate that the GB transformations can be induced by varying the temperature, loading the GB with point defects, or varying the amount of solute segregation. The atomic-level understanding obtained from such simulations can provide input for further development of thermodynamics theories and continuous models of interface phase transformations while simultaneously serving as a testing ground for validation of theories and models. They can also help interpret and guide experimental work in this field.

36 MATERIALS SCIENCE↗

Characterization and prediction of the electromechanical wear of contact tips during wire arc additive manufacturing of 316L stainless steel

Here, this study seeks to better understand the degradation of the contact tip with respect to WAAM for a 316L wire electrode as well as explore methods of monitoring the contact tip state from process data. The contact tip, a consumable component, positions the wire and serves as the electrical contact surface between the wire electrode and the welding power supply. The wear of the contact tip was characterized in terms of material loss and material contamination for a set of tips worn to discrete levels as measured by the amount of wire fed or arc time. Geometrical characterization found a 49% increase in the bore exit area at 180 meters of wire fed. Machine learning models were developed to predict the relative bore exit area of the contact tip from arc-based process data and a random forest classifier exhibited favorable performance with a cross-validated f1-score of 0.84. The regression architecture implemented a multi-layer perceptron with the ability to predict the relative exit area with an $R^2$ score of 0.75. Key features used in the prediction include the standard deviation of the voltage and the time between shorts.

Contact tip wear↗

BD Andromedae: A new short-period RS CVn eclipsing binary star with a distant tertiary body in a highly eccentric orbit

A photometric study of BD And was made through the analysis of two sets of new BVR light curves. The light curves with migrating photometric waves outside eclipse show that BD And is a short-period RS CVn-type binary star. The analysis of all available timings reveals that the orbital period has varied in a strictly cyclical way with a period of 9.2 yr. The periodic variation most likely arises from the light-time effect due to a tertiary moving in a highly elliptical orbit (e {sub 3} = 0.76). The Applegate mechanism could not operate properly in the eclipsing pair. The light curves were modeled with two large spots on the hotter star and a large third light amounting to about 14% of the total systemic light. BD And is a triple system: a detached binary system consisting of two nearly equal solar-type stars with an active primary star and a G6-G7 tertiary dwarf. The absolute dimensions of the eclipsing pair and tertiary components were determined. The three components with a mean age of about 5.8 Gyr are located at midpositions in main-sequence bands. The radius of the secondary is about 17% larger than that deduced from stellar models. The orbital and radiometric characteristics of the tertiary are intensively investigated. One important feature is that the mutual inclination between two orbits is larger than 60°, implying that Kozai cycles had occurred very efficiently in the past. The possible past and future evolutions of the BD And system, driven by KCTF and MBTF, are also discussed.

79 ASTRONOMY AND ASTROPHYSICS↗

An AeroCom assessment of black carbon in Arctic snow and sea ice

Though many global aerosols models prognose surface deposition, only a few models have been used to directly simulate the radiative effect from black carbon (BC) deposition to snow and sea ice. In this paper, we apply aerosol deposition fields from 25 models contributing to two phases of the Aerosol Comparisons between Observations and Models (AeroCom) project to simulate and evaluate within-snow BC concentrations and radiative effect in the Arctic. We accomplish this by driving the offline land and sea ice components of the Community Earth System Model with different deposition fields and meteorological conditions from 2004 to 2009, during which an extensive field campaign of BC measurements in Arctic snow occurred. We find that models generally underestimate BC concentrations in snow in northern Russia and Norway, while overestimating BC amounts elsewhere in the Arctic. Although simulated BC distributions in snow are poorly correlated with measurements, mean values are reasonable. The multi-model mean (range) bias in BC concentrations, sampled over the same grid cells, snow depths, and months of measurements, are -4.4 (-13.2 to +10.7) ng g -1 for an earlier phase of AeroCom models (phase I), and +4.1 (-13.0 to +21.4) ng g -1 for a more recent phase of AeroCom models (phase II), compared to the observational mean of 19.2 ng g -1 . Factors determining model BC concentrations in Arctic snow include Arctic BC emissions, transport of extra-Arctic aerosols, precipitation, deposition efficiency of aerosols within the Arctic, and meltwater removal of particles in snow. Sensitivity studies show that the model–measurement evaluation is only weakly affected by meltwater scavenging efficiency because most measurements were conducted in non-melting snow. The Arctic (60–90° N) atmospheric residence time for BC in phase II models ranges from 3.7 to 23.2 days, implying large inter-model variation in local BC deposition efficiency. Combined with the fact that most Arctic BC deposition originates from extra-Arctic emissions, these results suggest that aerosol removal processes are a leading source of variation in model performance. The multi-model mean (full range) of Arctic radiative effect from BC in snow is 0.15 (0.07–0.25) W m -2 and 0.18 (0.06–0.28) W m -2 in phase I and phase II models, respectively. After correcting for model biases relative to observed BC concentrations in different regions of the Arctic, we obtain a multi-model mean Arctic radiative effect of 0.17 W m -2 for the combined AeroCom ensembles. Finally, there is a high correlation between modeled BC concentrations sampled over the observational sites and the Arctic as a whole, indicating that the field campaign provided a reasonable sample of the Arctic.

aeroCom↗

Time-dependent outgassing and impurities in the NASA Lewis Bumpy Torus

To investigate the importance to fusion devices of desorption of gas from walls or cryosurfaces under long time operation, preliminary mass spectrometric investigations were carried out on the NASA Lewis Bumpy Torus with a 0.1-2A discharge in D2 at a pressure of 4.0 to 6.6 x 0.00001 torr. During the initial tens of minutes of discharge operation large quantities of a component with mass number 28, believed to be nitrogen, were released. The decrease with time of the nitrogen density after its initial maximum, indicated a diffusion controlled outgassing from cryodeposits or wall material. When cold surfaces were allowed to warm up, large quantities of gas were released. The integrated amount of N2 was typically the same as that released during a discharge, while the amount of H2O was orders of magnitude larger.

Persson, H.↗

A rocket-borne microprocessor-based experiment for investigation of energetic particles in the D and E regions

An energetic experiment using the Z80 family of microcomputer components is described. Data collected from the experiment allowed fast and efficient postprocessing, yielding both energy-spectrum and pitch-angle distribution of energetic particles in the D and E regions. Advanced microprocessor system architecture and software concepts were used in the design to cope with the large amount of data being processed. This required the Z80 system to operate at over 80% of its total capacity. The microprocessor system was included in the payloads of three rockets launched during the Energy Budget Campaign at ESRANGE, Kiruna, Sweden in November 1980. Based on preliminary examination of the data, the performance of the experiment was satisfactory and good data were obtained on the energy spectrum and pitch-angle distribution of the particles.

Braswell, F. M.↗

Data base for crack growth properties of materials

A computerized data base of crack growth properties of materials was developed for use in fracture control analysis of rocket engine components and other NASA space hardware. The software system has files of basic crack growth rate data, other fracture mechanics material properties such as fracture toughness and environmental crack growth threshold values, and plotting and fitting routines for deriving material properties for use in fracture control analysis. An extensive amount of data was collected and entered, and work is continuing on compiling additional data. The data base and software codes are useful both for fracture control analysis and for evaluation or development of improved crack growth theories.

Forman, Royce G.↗

ASRM Process Development in Aqueous Cleaning

Viewgraphs are included on process development in aqueous cleaning which is taking place at the Aerojet Advanced Solid Rocket Motor (ASRM) Division under a NASA Marshall Space and Flight Center contract for design, development, test, and evaluation of the ASRM including new production facilities. The ASRM will utilize aqueous cleaning in several manufacturing process steps to clean case segments, nozzle metal components, and igniter closures. ASRM manufacturing process development is underway, including agent selection, agent characterization, subscale process optimization, bonding verification, and scale-up validation. Process parameters are currently being tested for optimization utilizing a Taguci Matrix, including agent concentration, cleaning solution temperature, agitation and immersion time, rinse water amount and temperature, and use/non-use of drying air. Based on results of process development testing to date, several observations are offered: aqueous cleaning appears effective for steels and SermeTel-coated metals in ASRM processing; aqueous cleaning agents may stain and/or attack bare aluminum metals to various extents; aqueous cleaning appears unsuitable for thermal sprayed aluminum-coated steel; aqueous cleaning appears to adequately remove a wide range of contaminants from flat metal surfaces, but supplementary assistance may be needed to remove clumps of tenacious contaminants embedded in holes, etc.; and hot rinse water appears to be beneficial to aid in drying of bare steel and retarding oxidation rate.

Swisher, Bill↗

Evaluation of Non-Ozone-Depleting-Chemical Cleaning Methods for Space Mechanisms Using a Vacuum Spiral Orbit Rolling Contact Tribometer

Because CFC 113, an ozone depleting chemical (ODC), can no longer be produced, alternative bearing cleaning methods must be studied. The objective of this work was to study the effect of the new cleaning methods on lubricant lifetime using a vacuum bearing simulator (spiral orbit rolling contact tribometer). Four alternative cleaning methods were studied: ultra-violet (UV) ozone, aqueous levigated alumina slurry (ALAS), super critical fluid (SCF) CO2 and aqueous Brulin 815GD. Baseline tests were done using CFC 113. Test conditions were the following: a vacuum of at least 1.3 x 10(exp -6) Pa, 440C steel components, a rotational speed of 10 RPM, a lubricant charge of between 60-75 micrograms, a perfluoropolyalkylether lubricant (Z-25), and a load of 200N (44.6 lbs., a mean Hertzian stress of 1.5 GPa). Normalized lubricant lifetime was determined by dividing the total number of ball orbits by the amount of lubricant. The failure condition was a friction coefficient of 0.38. Post-test XPS analysis was also performed, showing slight variations in post-cleaning surface chemistry. Statistical analysis of the resultant data was conducted and it was determined that the data sets were most directly comparable when subjected to a natural log transformation. The natural log life (NL-Life) data for each cleaning method were reasonably normally (statistically) distributed and yielded standard deviations that were not significantly different among the five cleaning methods investigated. This made comparison of their NL-Life means very straightforward using a Bonferroni multiple comparison of means procedure. This procedure showed that the ALAS, UV-ozone and CFC 113 methods were not statistically significantly different from one another with respect to mean NL-Life. It also found that the SCF CO2 method yielded a significantly higher mean NL-Life than the mean NL-Lives of the ALAS, UV-ozone and CFC 113 methods. It also determined that the aqueous Brulin 815GD method yielded a mean NL-Life that was statistically significantly higher than the mean NL-Lives of each of the other four methods. Baseline tests using CFC 113 cleaned parts yielded a mean NL-Life 3.62 orbits/micro-g. ALAS and UV-ozone yielded similar mean NL-Life (3.31 orbits/mg and 3.33 orbits/micro-g, respectively). SCF CO2, gave a mean NL-Life of 4.08 orbits/mg and aqueous Brulin 8l5GD data yielded the longest mean NL-Life (4.66 orbits/micro-g).

Jansen, Mark J.↗