Search NASA⌕ Search

SEARCH · Search NASA

Results for “DIRECTION FINDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

Temporal and spatial variability in surface roughness and accumulation rate around 88° S from repeat airborne geophysical surveys

We use repeat high-resolution airborne geophysical data consisting of laser altimetry, snow, and Ku-band radar and optical imagery acquired in 2014, 2016, and 2017 to analyze the spatial and temporal variability in surface roughness, slope, wind deposition, and snow accumulation at 88° S, an elevation bias validation site for ICESat-2 and potential validation site for CryoSat-2. We find significant small-scale variability (<10 km) in snow accumulation based on the snow radar subsurface stratigraphy, indicating areas of strong wind redistribution are prevalent at 88° S. In general, highs in snow accumulation rate correspond with topographic lows, resulting in a negative correlation coefficient of r(exp 2)=−0.32 between accumulation rate and MSWD (mean slope in the mean wind direction). This relationship is strongest in areas where the dominant wind direction is parallel to the survey profile, which is expected as the geophysical surveys only capture a two-dimensional cross section of snow redistribution. Variability in snow accumulation appears to correlate with variability in MSWD. The correlation coefficient between the standard deviations of accumulation rate and MSWD is r(exp 2)=0.48, indicating a stronger link between the standard deviations than the actual parameters. Our analysis shows that there is no simple relationship between surface slope, wind direction, and snow accumulation rates for the overall survey area. We find high variability in surface roughness derived from laser altimetry measurements on length scales smaller than 10 km, sometimes with very distinct and sharp transitions. Some areas also show significant temporal variability over the course of the 3 survey years. Ultimately, there is no statistically significant slope-independent relationship between surface roughness and accumulation rates within our survey area. The observed correspondence between the small-scale temporal and spatial variability in surface roughness and backscatter, as evidenced by Ku-band radar signal strength retrievals, will make it difficult to develop elevation bias corrections for radar altimeter retrieval algorithms.

Michael Studinger↗

THE ABSOLUTE MAGNITUDE OF RRc VARIABLES FROM STATISTICAL PARALLAX

We present the first definitive measurement of the absolute magnitude of RR Lyrae c-type variable stars (RRc) determined purely from statistical parallax. We use a sample of 242 RRc variables selected from the All Sky Automated Survey for which high-quality light curves, photometry, and proper motions are available. We obtain high-resolution echelle spectra for these objects to determine radial velocities and abundances as part of the Carnegie RR Lyrae Survey. We find that M{sub V,RRc} = 0.59 ± 0.10 at a mean metallicity of [Fe/H] = –1.59. This is to be compared with previous estimates for RRab stars (M{sub V,RRab} = 0.76 ± 0.12) and the only direct measurement of an RRc absolute magnitude (RZ Cephei, M{sub V,RRc} = 0.27 ± 0.17). We find the bulk velocity of the halo relative to the Sun to be (W{sub π}, W{sub θ}, W{sub z} ) = (12.0, –209.9, 3.0) km s{sup –1} in the radial, rotational, and vertical directions with dispersions (σ{sub W{sub π}},σ{sub W{sub θ}},σ{sub W{sub z}}) = (150.4, 106.1, 96.0) km s{sup -1}. For the disk, we find (W{sub π}, W{sub θ}, W{sub z} ) = (13.0, –42.0, –27.3) km s{sup –1} relative to the Sun with dispersions (σ{sub W{sub π}},σ{sub W{sub θ}},σ{sub W{sub z}}) = (67.7,59.2,54.9) km s{sup -1}. Finally, as a byproduct of our statistical framework, we are able to demonstrate that UCAC2 proper-motion errors are significantly overestimated as verified by UCAC4.

79 ASTRONOMY AND ASTROPHYSICS↗

Statistical studies of spinning black-hole binaries

We study the statistical distributions of the spins of generic black-hole binaries during the inspiral and merger, as well as the distributions of the remnant mass, spin, and recoil velocity. For the inspiral regime, we start with a random uniform distribution of spin directions S-vector{sub 1} and S-vector{sub 2} over the sphere and magnitudes |S-vector{sub 1}/m{sub 1}{sup 2}|=|S-vector{sub 2}/m{sub 2}{sup 2}|=0.97 for different mass ratios, where S-vector{sub i} and m{sub i} are the spin-angular momentum and mass of the ith black hole. Starting from a fiducial initial separation of R{sub i}=50M, we perform 3.5-post-Newtonian-order evolutions down to a separation of R{sub f}=5M, where M=m{sub 1}+m{sub 2}, the total mass of the system. At this final fiducial separation, we compute the angular distribution of the spins with respect to the final orbital angular momentum, L-vector. We perform 16{sup 4}=65 536 simulations for six mass ratios between q=1 and q=1/16 and compute the distribution of the angles L-vector{center_dot}{Delta}-vector and L-vector{center_dot}S-vector, directly related to recoil velocities and total angular momentum. We find a small but statistically significant bias of the distribution towards counteralignment of both scalar products. A post-Newtonian analysis shows that radiation-reaction-driven dissipative effects on the orbital angular momentum lead to this bias. To study the merger of black-hole binaries, we turn to full numerical techniques. In order to make use of the numerous simulations now available in the literature, we introduce empirical formulas to describe the final remnant black-hole mass, spin, and recoil velocity for merging black-hole binaries with arbitrary mass ratios and spins. Our formulas are based on the post-Newtonian scaling, to model the plunge phase, with amplitude parameters chosen by a least-squares fit of recently available fully nonlinear numerical simulations, supplemented by inspiral losses from infinity to the innermost stable circular orbit. We then evaluate those formulas for randomly chosen directions of the individual spins and magnitudes as well as the binary's mass ratio. The number of evaluations has been chosen such that there are 10 configurations per each dimension of this parameter space, i.e. 10{sup 7}. We found that the magnitude of the recoil velocity distribution decays exponentially as P(v){approx}exp(-v/2500 km s{sup -1}) with mean velocity <v>=630 km s{sup -1} and standard deviation {radical}(<v{sup 2}>-<v>{sup 2})=534 km s{sup -1}, leading to a 23% probability of recoils larger than 1000 km s{sup -1}, and a highly peaked angular distribution along the final orbital axis. The studies of the distribution of the final black-hole spin magnitude show a universal distribution highly peaked at S{sub f}/m{sub f}{sup 2}=0.73 and a 25 deg. misalignment with respect to the final orbital angular momentum, just prior to full merger of the holes. We also compute the statistical dependence of the magnitude of the recoil velocity with respect to the ejection angle. The spin and recoil velocity distributions are also displayed as a function of the mass ratio. Finally, we compute the effects of the observer orientation with respect to the recoil velocity vector to take into account the probabilities to measure a given redshifted (or blueshifted) radial velocity of accretion disks with respect to host galaxies.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Type-I 2HDM under the Higgs and electroweak precision measurements

We explore the extent to which future precision measurements of the Standard Model (SM) observables at the proposed Z -factories and Higgs factories may have impacts on new physics beyond the Standard Model, as illustrated by studying the Type-I Two-Higgs-doublet model (Type-I 2HDM). We include the contributions from the heavy Higgs bosons at the tree-level and at the one-loop level in a full model-parameter space. While only small tan β region is strongly constrained at tree level, the large tan β region gets constrained at loop level due to tan β enhanced tri-Higgs couplings. We perform a multiple variable χ 2 fit with non-alignment and non-degenerate masses. We find that the allowed parameter ranges could be tightly constrained by the future Higgs precision measurements, especially for small and large values of tan β . Indirect limits on the masses of heavy Higgs bosons can be obtained, which can be complementary to the direct searches of the heavy Higgs bosons at hadron colliders. We also find that the expected accuracies at the Z -pole and at a Higgs factory are quite complementary in constraining mass splittings of heavy Higgs bosons. The typical results are | cos( β - α ) | < 0 . 05 , | Δ m Φ | < 200 GeV, and tan β ≳ 0 . 3. The reaches from CEPC, Fcc-ee and ILC are also compared, for both Higgs and Z -pole precision measurements. Comparing to the Type-II 2HDM, the 95% C.L. allowed range of cos( β - α ) is larger, especially for large values of tan β .

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Quashing a suspected selection bias in galaxy samples having dynamically measured supermassive black holes

Local early-type galaxies (ETGs) with directly measured black hole masses, M bh , have been reported to represent a biased sample relative to the ETG population at large. Such galaxies with Spitzer Space Telescope imaging have been purported to possess velocity dispersions, σ, at least ∼0.1 dex larger for a given galaxy stellar mass, M * , gal , than is typically observed among thousands of ETGs imaged by the Sloan Digital Sky Survey (SDSS). This apparent offset led Shankar et al. to reduce the normalisation of the observed M bh ∝ σ 5 relation by at least ∼0.5 dex to give their ‘intrinsic relations’, including σ-based modifications to the observed M bh –M * , gal relation. These modifications were based on the untested assumption that the stellar masses had been derived consistently between the two samples. Here, we provide the necessary check using galaxies common to the Spitzer Survey of Stellar Structure in Galaxies (S 4 G) and the SDSS. We find that the stellar masses of galaxies with and without directly measured black hole masses had appeared offset from each other due to the use of inconsistent stellar mass-to-light ratios, Υ * , for the optical and infrared data. We briefly discuss the ‘intrinsic relations’ and why some of these will at times appear to have had partial success when applied to data based on similarly inconsistent values ofΥ * . Finally, we reiterate the importance of the υ (lower-case Υ) term, which we previously introduced into the M bh –M * relations to help avoid Υ * -related mismatches.

79 ASTRONOMY AND ASTROPHYSICS↗

Smectic and nematic phase modulations and transitions under electron beam in Tb 2 Cu 0.83 Pd 0.17 O 4

Understanding the structural origin of the functionality in cuprates has attracted tremendous attention over several decades. In particular, probing distortions in the Cu- O bonding is of great importance for exploring the coupling between the charge and the lattice, a key mechanism for superconductivity and other functionality in correlated materials. Here we study a superlattice modulation in the Tb 2 Cu 0.83 Pd 0.17 O 4 “214” material, which possesses no superconductivity itself but has the parent structure of the R 2 CuO 4 (R = a rare earth element) superconducting cuprate group. Using transmission electron microscopy (TEM), we find that this superlattice modulation is formed by Cu ion displacements in a direction perpendicular to the Cu-O planes. The superlattice modulation undergoes a reversible electronic smectic-nematic phase transition under electron-beam illumination. With the help of in situ TEM results, our findings imply that the superlattice modulation in this material arises from spatially modulated charge ordering at the Cu sites.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Direct determination of momentum-resolved electron transfer in the photoexcited van der Waals heterobilayer WS 2 /MoS 2

Photoinduced charge separation in transition-metal dichalcogenide heterobilayers is being explored for moiré excitons, spin-valley polarization, and quantum phases of excitons/electrons. While different momentum points can be critically involved in charge separation dynamics, little is known directly from experiments. Here we determine momentum-resolved electron dynamics in the WS 2 /MoS 2 heterobilayer using time- and angle-resolved photoemission spectroscopy. Upon photoexcitation in the $\textit{K}$ valleys, we detect electrons in $\textit{M/2}$, $\textit{M}$, and $\textit{Q}$ valleys/points on timescales as short as ~70 fs, followed by dynamic equilibration in K and Q valleys in ~400 fs. Overall, these findings reveal the essential role of phonon scattering, the coexistence of direct and indirect interlayer excitons, and constraints on spin-valley polarization.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Evaluation of the Rapid Refresh Numerical Weather Prediction Model over Arctic Alaska

Abstract Despite a need for accurate weather forecasts for societal and economic interests in the U.S. Arctic, thorough evaluations of operational numerical weather prediction in the region have been limited. In particular, the Rapid Refresh Model (RAP), which plays a key role in short-term forecasting and decision-making, has seen very limited assessment in northern Alaska, with most evaluation efforts focused on lower latitudes. In the present study, we verify forecasts from version 4 of the RAP against radiosonde, surface meteorological, and radiative flux observations from two Arctic sites on the northern Alaskan coastline, with a focus on boundary layer thermodynamic and dynamic biases, model representation of surface inversions, and cloud characteristics. We find persistent seasonal thermodynamic biases near the surface that vary with wind direction, and may be related to the RAP’s handling of sea ice and ocean interactions. These biases seem to have diminished in the latest version of the RAP (version 5), which includes refined handling of sea ice, among other improvements. In addition, we find that despite capturing boundary layer temperature profiles well overall, the RAP struggles to consistently represent strong, shallow surface inversions. Further, while the RAP seems to forecast the presence of clouds accurately in most cases, there are errors in the simulated characteristics of these clouds, which we hypothesize may be related to the RAP’s treatment of mixed-phase clouds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nonradiative Plasmon Decay and Hot Carrier Dynamics: Effects of Phonons, Surfaces, and Geometry

The behavior of metals across a broad frequency range from microwave to ultraviolet frequencies is of interest in plasmonics, nanophotonics, and metamaterials. Depending on the frequency, losses of collective excitations in metals can be predominantly classical resistive effects or Landau damping. In this context, we present first-principles calculations that capture all of the significant microscopic mechanisms underlying surface plasmon decay and predict the initial excited carrier distributions so generated. Particularly, we include ab initio predictions of phonon-assisted optical excitations in metals, which are critical to bridging the frequency range between resistive losses at low frequencies and direct interband transitions at high frequencies. In the commonly used plasmonic materials, gold, silver, copper, and aluminum, we find that resistive losses compete with phonon-assisted carrier generation below the interband threshold, but hot carrier generation via direct transitions dominates above threshold. Furthermore, we predict energy-dependent lifetimes and mean free paths of hot carriers, accounting for electron–electron and electron–phonon scattering, to provide insight toward transport of plasmonically generated carriers at the nanoscale.

36 MATERIALS SCIENCE↗

Design and Operation of an Electrochemical Methanol Concentration Sensor for Direct Methanol Fuel Cell Systems

The development of a 150-Watt packaged power source based on liquid feed direct methanol fuel cells is being pursued currently at the Jet propulsion Laboratory for defense applications. In our studies we find that the concentration of methanol in the fuel circulation loop affects the electrical performance and efficiency the direct methanol fuel cell systems significantly. The practical operation of direct methanol fuel cell systems, therefore, requires accurate monitoring and control of methanol concentration. The present paper reports on the principle and demonstration of an in-house developed electrochemical sensor suitable for direct methanol fuel cell systems.

Narayanan, S. R.↗

Three-dimensional character of the deformation twin in magnesium

Deformation twins are three-dimensional domains, traditionally viewed as ellipsoids because of their two-dimensional lenticular sections. In this work, we performed statistical analysis of twin shapes viewing along three orthogonal directions: the ‘dark side’ (DS) view along the twin shear direction (η 1 ), the twinning plane normal (TPN) view (k 1 ) and the ‘bright side’ (BS) view along the direction λ(=k 1 × η 1 ). Our electron back-scatter diffraction results show that twins in the DS and BS views normally exhibit a lenticular shape, whereas they show an irregular shape in the TPN view. Moreover, the findings in the TPN view revealed that twins grow faster along λ the lateral direction than along η 1 the forward propagation direction at the initial stages of twin growth. These twin sections are irregular, indicating that growth is locally controlled and the overall shape is not perfectly ellipsoidal. We explain these findings using atomistic models, and ascribe them to differences in the mobility of the edge and screw components of the twinning dislocations.

36 MATERIALS SCIENCE↗

Theory of gradient drift instabilities in low-temperature, partially magnetised plasmas

A fluid dispersion theory in partially magnetised plasmas is analysed to examine the conditions under which large-wavelength modes develop in Penning-type configurations, that is, where an electric field is imposed perpendicular to a homogeneous magnetic field. The fluid dispersion relation assuming a slab geometry shows that two types of low-frequency, gradient drift instabilities occur in the direction of the E×B and diamagnetic drifts. One type of instability, observed when the equilibrium electric field and plasma density gradient are in the same direction, is similar to the classic modified Simon–Hoh instability. A second instability is found for conditions in which (i) the diamagnetic drift is in the direction opposite to the E×B drift and (ii) the magnitude of the diamagnetic drift is sufficiently larger than the electron thermal speed. The present fluid dispersion theory suggests that the rotating spokes driven by such fluid instabilities propagate in the same direction as the diamagnetic drift, which can be in the same direction as or opposite to the E×B drift, depending on the plasma conditions. This finding may account for the observation, in some plasma devices, of the rotation of large-scale structures in both the E×B and -E×B directions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Scheduling and Pricing for Expected Ramp Capability in Real-Time Power Markets

Higher variable renewable generation penetrations are occurring throughout the world on different power systems. These resources increase the variability and uncertainty on the system which must be accommodated by an increase in the flexibility of the system resources in order to maintain reliability. Many scheduling strategies have been discussed and introduced to ensure that this flexibility is available at multiple timescales. To meet variability, that is, the expected changes in system conditions, two recent strategies have been introduced: time-coupled multi-period market clearing models and the incorporation of ramp capability constraints. To appropriately evaluate these methods, it is important to assess both efficiency and reliability. But it is also important to assess the incentive structure to ensure that resources asked to perform in different ways have the proper incentives to follow these directions, which is a step often ignored in simulation studies. Here we find that there are advantages and disadvantages to both approaches. We also find that look-ahead horizon length in multi-period market models can impact incentives. This paper proposes scheduling and pricing methods that ensure expected ramps are met reliably, efficiently, and with associated prices based on true marginal costs that incentivize resources to do as directed by the market. Case studies show improvements of the new method.

25 ENERGY STORAGE↗

Multiple Roles of Alkanethiolate‐Ligands in Direct Formation of H 2 O 2 over Pd Nanoparticles

Abstract Coadsorbed organic species including thiolates can promote direct synthesis of hydrogen peroxide from H 2 and O 2 over Pd particles. Here, density functional theory based kinetic modeling, augmented with activity measurements and vibrational spectroscopy are used to provide atomistic understanding of direct H 2 O 2 formation over alkylthiolate(RS) Pd. We find that the RS species are oxidized during reaction conditions yielding RSO 2 as the effective ligand. The RSO 2 ligand shows superior ability for proton transfer to the intermediate surface species OOH, which accelerates the formation of H 2 O 2 . The ligands promote the selectivity also by blocking sites for unselective water formation and by modifying the electronic structure of Pd. The work rationalizes observations of enhanced selectivity of direct H 2 O 2 formation over ligand‐funtionalized Pd nanoparticles and shows that engineering of organic surface modifiers can be used to promote desired hydrogen transfer routes.

Chen, Lin↗

Multiple Roles of Alkanethiolate‐Ligands in Direct Formation of H 2 O 2 over Pd Nanoparticles

Abstract Coadsorbed organic species including thiolates can promote direct synthesis of hydrogen peroxide from H 2 and O 2 over Pd particles. Here, density functional theory based kinetic modeling, augmented with activity measurements and vibrational spectroscopy are used to provide atomistic understanding of direct H 2 O 2 formation over alkylthiolate(RS) Pd. We find that the RS species are oxidized during reaction conditions yielding RSO 2 as the effective ligand. The RSO 2 ligand shows superior ability for proton transfer to the intermediate surface species OOH, which accelerates the formation of H 2 O 2 . The ligands promote the selectivity also by blocking sites for unselective water formation and by modifying the electronic structure of Pd. The work rationalizes observations of enhanced selectivity of direct H 2 O 2 formation over ligand‐funtionalized Pd nanoparticles and shows that engineering of organic surface modifiers can be used to promote desired hydrogen transfer routes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Silent and Efficient Supersonic Bi-Directional Flying Wing

The supersonic bi-directional (SBiDir) flying wing (FW) concept has a great potential to achieve low sonic boom with high supersonic aerodynamic performance due to removal of performance conflict between high speed and low speed by rotating goo in flight. This NIAC Phase 1 research has achieved three objectives: 2) prove the concept based on simulation that it can achieve very low boom with smooth Sine wave ground over-pressure signature and excellent aerodynamic efficiency; 3) conduct trade study to correlate the geometric parameters with sonic boom and aerodynamic performance for further automated design optimization in Phase II. The design methodology developed in Phase I includes three parts: 1) an advanced geometry model, which can vary airfoil meanline angle distribution to control the expansion and shock waves on the airplane surface to mitigate sonic boom and improve aerodynamic efficiency. 2) a validated CFD procedure to resolve near field flow with accurate shock strength. The sonic boom propagation from near field to far field ground is simulated by NASA NF Boom code. The surface friction drag prediction is based on fiat plate correlation adopted by Seebass and supported by the experimental study of Winter and Smith, which is on the conservative side and is more reliable than CFD RANS simulation. 3) a mission analysis tool based on Corke's model that provides design requirements and constraints of supersonic airplanes for range, payload, volume, size, weight, etc. The design mission target is a supersonic transport with cruise Mach number 1.6, 100 passengers, and 4000nm range. The trade study has several very important findings: 1) The far field ground sonic boom signature is directly related to the smoothness of the flow on the airplane surface. The meanline angle distribution is a very effective control methodology to mitigate surface shock and expansion wave strength, and mitigating compression wave coalescing by achieving smooth loading distribution chord-wise. Compared with a linear meanline angle distribution, a design using nonlinear and non-monotonic meanline angle distribution is able to reduce the sonic boom ground loudness by over 20dBP1. The design achieves sonic boom ground loudness less than 70dBP1 and aerodynamic dynamic efficiency 1/D of 8.4. 2) Decreasing sweep angle within the Mach cone will increase 1/D as well as sonic boom. A design with variable sweep from 84° at the very leading edge to 68° at the tip achieves an extraordinarily high 1/D of 10.4 at Mach number 1.6 due to the low wave drag. If no sonic boom constraint is attached, SBiDir-FW concept still has a lot of room to increase the 1/D. 3) The round leading edge and trailing edge under high sweep angle are beneficial to improve aerodynamic performance, sonic boom, and to increase volume of the airplane. 4) Subsonic performance is benefited greatly from the high slenderness of supersonic configuration after rotating goo. A design with excellent supersonic aspect ratio of 0.44, 1/D of 8.g, gives an extraordinary subsonic aspect ration of 10 and 1/D of 1g.7. Two configurations are designed in details to install internal seats, landing gears, and engine installation to demonstrate the feasibility of SBiDir-FW configuration to accommodate all the required volume for realistic airplane. Here we emphasize that the qualitative findings in Phase I are very encouraging, more important than the quantitative results. Qualitative findings give the understanding of physics and provide the path to achieve the ultimate high performance design. The promising quantitative results achieved in Phase I need to be confirmed by wind tunnel testing in Phase II and ultimately proved by flight test. The other important step forward will be made to study the rotation transition from both CFD unsteady simulation and wind tunnel testing.

Zha, Gecheng↗

Microemulsions in the driven Widom-Rowlinson lattice gas

An investigation of the two-dimensional Widom-Rowlinson lattice gas under an applied drive uncovered a remarkable nonequilibrium steady state in which uniform stripes (reminiscent of an equilibrium lamellar phase) form perpendicular to the drive direction [R. Dickman and R. K. P. Zia, Phys. Rev. E 97, 062126 (2018)]. Here we study this model at low particle densities in two and three dimensions, where we find a disordered phase with a characteristic length scale (a “microemulsion”) along the drive direction. Further we develop a continuum theory of this disordered phase to derive a coarse-grained field-theoretic action for the nonequilibrium dynamics. The action has the form of two coupled driven diffusive systems with different characteristic velocities, generated by an interplay between the particle repulsion and the drive. We then show how fluctuation corrections in the field theory may generate the characteristic features of the microemulsion phase, including a peak in the static structure factor corresponding to the characteristic length scale. This work lays the foundation for understanding the stripe phenomenon more generally.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Grain growth competition during thin-sample directional solidification of dendritic microstructures: A phase-field study

Here we present the results of a comprehensive phase-field study of columnar grain growth competition in bi-crystalline samples in two dimensions (2D) and in three dimensions (3D) for small sample thicknesses allowing a single row of dendrites to form. We focus on the selection of grain boundary (GB) orientation during directional solidification in the steady-state dendritic regime, and study its dependence upon the orientation of two competing grains. In 2D, we map the entire orientation range for both grains, performing several simulations for each configuration to account for the stochasticity of GB orientation selection and to assess the average GB behavior. We find that GB orientation selection depends strongly on whether the primary dendrite growth directions have lateral components (i.e. components perpendicular to the axis of the temperature gradient) that point in the same or opposite directions in the two grains. Here, we identify a range of grain orientations in which grain selection follows the classical description of Walton and Chalmers. We also identify conditions that favor unusual overgrowth of favorably-oriented dendrites at a converging GB. We propose a simple analytical description that reproduces the average GB orientation selection from 2D simulations within statistical fluctuations of a few degrees. In 3D, we find a similar GB orientation selection as in 2D when secondary branches grow in planes parallel and perpendicular to the sample walls. Remarkably, quasi-2D behavior is also observed even when those perpendicular sidebranching planes are rotated by a finite azimuthal angle about the primary dendrite growth axis as long as the absolute values of those azimuthal angles are equal in both grains. In contrast, when the absolute values of those azimuthal angles differ markedly, we find that unusual overgrowth events at a converging GB are promoted by a high azimuthal angle in the least-favorably-oriented grain. We also find that diverging GBs can be strongly affected by those azimuthal angles, while converging GBs exhibit a weak dependence on those angles. Finally, for diverging GBs, GB orientation is also strongly affected by the relative signs of the lateral components of the primary dendrite growth directions in both grains.

36 MATERIALS SCIENCE↗