Search NASA⌕ Search

SEARCH · Search NASA

Results for “Speed Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

Optimizing Hammermill Performance Through Screen Selection and Hammer Design

Background: Mechanical preprocessing, which includes particle size reduction and mechanical separation, is one of the primary operations in the feedstock supply system for a lignocellulosic biorefinery. It is the means by which raw biomass from the field or forest is mechanically transformed into an on-spec feedstock with characteristics better suited for the fuel conversion process. Results: This work provides a general overview of the objectives and methodologies of mechanical preprocessing and then presents experimental results illustrating (1) improved size reduction via optimization of hammer mill configuration, (2) improved size reduction via pneumatic-assisted hammer milling, and (3) improved control of particle size and particle size distribution through proper selection of grinder process parameters. Conclusion: Optimal grinder configuration for maximal process throughput and efficiency is strongly dependent on feedstock type and properties, such moisture content. Tests conducted using a HG200 hammer grinder indicate that increasing the tip speed, optimizing hammer geometry, and adding pneumatic assist can increase grinder throughput as much as 400%.

09 BIOMASS FUELS↗

Development of a Residential Ground-Source Integrated Heat Pump

A residential-size ground-source integrated heat pump (GSIHP) system has been developed and is currently being field tested. The system is a nominal 2-ton (7 kW) cooling capacity, variable-speed unit, which is multi-functional, e.g. space cooling, space heating, dedicated water heating, and simultaneous space cooling and water heating. High-efficiency brushless permanent-magnet (BPM) motors are used for the compressor, indoor blower, and pumps to obtain the highest component performance and system control flexibility. Laboratory test data were used to calibrate a vapor-compression simulation model (HPDM) for each of the four primary modes of operation. The model was used to optimize the internal control options and to simulate the selected internal control strategies, such as controlling to a constant air supply temperature in the space heating mode and a fixed water temperature rise in water heating modes. Equipment performance maps were generated for each operation mode as functions of all independent variables for use in TRNSYS annual energy simulations. These were performed for the GSIHP installed in a well-insulated 2600 ft2(242 m2) house and connected to a vertical ground loop heat exchanger(GLHE). We selected a 13 SEER (3.8 CSPF )/7.7 HSPF (2.3 HSPF, W/W) ASHP unit with 0.90 Energy Factor (EF) resistance water heater as the baseline for energy savings comparisons. The annual energy simulations were conducted over five US climate zones. In addition, appropriate ground loop sizes were determined for each location to meet 10-year minimum and maximum design entering water temperatures (EWTs) to the equipment. The prototype GSIHP system was predicted to use 52 to 59% less energy than the baseline system while meeting total annual space conditioning and water heating loads.

Energy Efficiency↗

Integrated Electric Drive with HV 2 Modular Electric Machine and SiC Based Power Converters (Final Report)

An innovative high performance, high speed electric drive is designed, fabricated and tested. The drive is based on the modular multilevel converter (MMC) topology and is synthesized using power electronic building blocks (submodules) that utilize the newest generation of silicon-carbide (SiC) semiconductors. Power modules from two suppliers are investigated, characterized and the one showing better performance selected. A prototype MMC submodule is designed, built and tested in the lab. Simultaneously, control hardware and software are implemented and tested using real-time simulators. After verification of each of the subsystems, all subsystems are integrated to form a DC/AC converter-based drive. Multiple configurations are assembled and tested, and operation in variable voltages and frequencies, up to 4,160 V (line-to-line, rms), 140 A (rms) and 0-1,000 Hz is achieved. The efficiency of the drive system accomplished in the project is higher than 99.2% and the volume is 70% smaller than that of state-of-the art drives made using conventional technologies.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Visualization of Atomization Gas Flow and Melt Break-up Effects in Response to Nozzle Design

Both powder particle size control and efficient use of gas flow energy are highly prized goals for gas atomization of metal and alloy powder to minimize off-size powder inventory (or 'reverb') and excessive gas consumption. Recent progress in the design of close-coupled gas atomization nozzles and the water model simulation of melt feed tubes were coupled with previous results from several types of gas flow characterization methods, e.g., aspiration measurements and gas flow visualization, to make progress toward these goals. Size distribution analysis and high speed video recordings of gas atomization reaction synthesis (GARS) experiments on special ferritic stainless steel alloy powders with an Ar+O{sub 2} gas mixture were performed to investigate the operating mechanisms and possible advantages of several melt flow tube modifications with one specific gas atomization nozzle. In this study, close-coupled gas atomization under closed wake gas flow conditions was demonstrated to produce large yields of ultrafine (dia.<20 {mu}m) powders (up to 32%) with moderate standard deviations (1.62 to 1.99). The increased yield of fine powders is consistent with the dual atomization mechanisms of closed wake gas flow patterns in the near-field of the melt orifice. Enhanced size control by stabilized pre-filming of the melt with a slotted trumpet bell pour tube was not clearly demonstrated in the current experiments, perhaps confounded by the influence of the melt oxidation reaction that occurred simultaneously with the atomization process. For this GARS variation of close-coupled gas atomization, it may be best to utilize the straight cylindrical pour tube and closed wake operation of an atomization nozzle with higher gas mass flow to promote the maximum yields of ultrafine powders that are preferred for the oxide dispersion strengthened alloys made from these powders.

36 MATERIALS SCIENCE↗

NREL Integrate: RCS-4-42326

OMNETRIC Corp., Duke Energy, CPS Energy, and the University of Texas at San Antonio (UTSA) created a project team to execute the project 'OpenFMB Reference Architecture Demonstration.' The project included development and demonstration of concepts that will enable the electric utility grid to host larger penetrations of renewable resources. The project concept calls for the aggregation of renewable resources and loads into microgrids and the control of these microgrids with an implementation of the OpenFMB Reference Architecture. The production of power from the renewable resources that are appearing on the grid today is very closely linked to the weather. The difficulty of forecasting the weather, which is well understood, leads to difficulty in forecasting the production of renewable resources. The current state of the art in forecasting the power production from renewables (solar PV and wind) are accuracies in the range of 12-25 percent NMAE. In contrast the demand for electricity aggregated to the system level, is easier to predict. The state of the art of demand forecasting done, 24 hours ahead, is about 2-3% MAPE. Forecasting the load to be supplied from conventional resources (demand minus generation from renewable resources) is thus very hard to forecast. This means that even a few hours before the time of consumption, there can be considerable uncertainty over what must be done to balance supply and demand. Adding to the problem of difficulty of forecasting, is the reality of the variability of the actual production of power from renewables. Due to the variability of wind speeds and solar insolation, the actual output of power from renewable resources can vary significantly over a short period of time. Gusts of winds result is variation of power output of wind turbines. The shadows of clouds moving over solar PV arrays result in the variation of power production of the array. This compounds the problem of balancing supply and demand in real time. Establishing a control system that can manage distribution systems with large penetrations of renewable resources is difficult due to two major issues: (1) the lack of standardization and interoperability between the vast array of equipment in operation and on the market, most of which use different and proprietary means of communication and (2) the magnitude of the network and the information it generates and consumes. The objective of this project is to provide the industry with a design concept and tools that will enable the electric power grid to overcome these barriers and support a larger penetration of clean energy from renewable resources.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Enabling cooperative adaptive cruise control on strings of vehicles with heterogeneous dynamics and powertrains

Recent studies have shown that positive impact of Cooperative Adaptive Cruise Control (CACC) can only be guaranteed as market penetration rate increases. Removing the string homogeneity constraint is essential to encourage widespread adoption. In this work, a hierarchical architecture is proposed to enable CACC on vehicles with not only mixed dynamics but also different powertrain types. A low-level layer deals with the vehicle and powertrain dynamics to provide accurate and consistent reference speed tracking response. The high-level layer uses: (1) a Linear Parameter Varying feedback system to provide loop stability, robustness and enforce a variable time gap policy and (2) a feedforward system that processes Vehicle-to-Vehicle information to enhance string stability and response bandwidth, by dealing with the string heterogeneity. A gap management strategy is built on top of the CACC architecture to handle gap setting changes or cut-in/out situations, via a dynamics constrained time gap trajectory planning algorithm. We report the proposed work has been designed, developed and validated on three different real passenger vehicles on public highways and test tracks, showing the potential of the proposed algorithm to enable robust string stable CACC, despite the different dynamics and powertrains considered.

33 ADVANCED PROPULSION SYSTEMS↗

Laser-driven Acceleration in Clustered Plasmas

We propose a new approach to avoid dephasing limitation of laser wakefield acceleration by manipulating the group velocity of the driving pulse using clustered plasmas. We demonstrated the control of phase velocity in clustered plasmas by third harmonic generation and frequency domain interferometry experiments. The results agree with a numerical model. Based on this model, the group velocity of the driving pulse in clustered plasmas was calculated and the result shows the group velocity can approach the speed of light c in clustered plasmas.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Online Detection of Power Grid Anomalies via Federated Learning

Data from sensors is critical for advanced applica- tions that support efficient, reliable, and resilient electric grid operations. Historically, data from phasor measurement units (PMU) has been utilized to develop a wide variety of wide area control and protection applications suitable for power grid control centers. However, until now, most of these could not be deployed for automated operations due to a set of data corruption challenges and uncertainty in the incoming data pipeline. In this paper, we address the problem of detecting different variety of anomalies that are evident in different high- speed power grid measurements. The paper discusses a workflow for handling problems with data acquisition and highlights some of the key findings suitable for anomaly detection in a centralized and distributed environment. The effectiveness of the proposed method was demonstrated with results utilizing realistic PMU datasets

Shinkle, Matthew W.↗

Ultrasonic deterrents provide no additional benefit over curtailment in reducing bat fatalities at an Ohio wind energy facility

Wind energy is important for achieving net-zero greenhouse gas emissions but also contributes to global bat mortality. Current strategies to minimize bat mortality due to collision with wind-turbine blades fall broadly into two categories: curtailment (limiting turbine operation during high-risk periods) and deterrence (discouraging bat activity near turbines). Recently, there has been interest in combining these strategies to achieve greater reductions in bat fatalities than either strategy might achieve in isolation. To investigate the effectiveness of combining curtailment with ultrasonic deterrent minimization strategies, we deployed six ultrasonic deterrents at nacelle height on 16 experimental turbines at Avangrid Renewables’ Blue Creek Wind Energy Facility. We rotated between four conditions (normal operations, curtailment only, deterrent only, curtailment and deterrent) randomly assigned to four wind turbines each night between 15 June and 3 October 2017. We found that bat mortality at wind turbines was independent of wind speed. The effectiveness of ultrasonic acoustic deterrents varied between high-frequency-calling species (eastern red bats) and low-frequency-calling species (hoary bats, silver-haired bats, and big brown bats). When deterrents were active, mortality was twice as high for eastern red bats compared to the control. Conversely, deterrents had a weak dampening effect on bat mortality for low-frequency species. We found no additive effects on mortality reduction for turbines operating both curtailment and deterrents compared to either approach in isolation. Our findings suggest that ultrasonic acoustic deterrents may not be effective for both high and low frequency echolocating bats. The increase in fatalities of eastern red bats is alarming and underscores the importance of considering site- and species-specific effects of minimization solutions.

60 APPLIED LIFE SCIENCES↗

Prototype Systems for Measuring Outdoor Air Intake Rates in Rooftop Air Handlers

The widespread absence of systems for real-time measurement and feedback control, of minimum outdoor air intake rates in HVAC systems contributes to the poor control of ventilation rates in commercial buildings. Ventilation rates affect building energy consumption and influence occupant health. The project designed fabricated and tested four prototypes of systems for measuring rates of outdoor air intake into roof top air handlers. All prototypes met the ±20% accuracy target at low wind speeds, with all prototypes accurate within approximately ±10% after application of calibration equations. One prototype met the accuracy target without a calibration. With two of four prototype measurement systems, there was no evidence that wind speed or direction affected accuracy; however, winds speeds were generally below usually 3.5 m s -1 (12.6 km h -1 ) and further testing is desirable. The airflow resistance of the prototypes was generally less than 35 Pa at maximum RTU air flow rates. A pressure drop of this magnitude will increase fan energy consumption by approximately 4%. The project did not have resources necessary to estimate costs of mass produced systems. The retail cost of components and materials used to construct prototypes ranged from approximately $1,200 to $1,700. The test data indicate that the basic designs developed in this project, particularly the designs of two of the prototypes, have considerable merit. Further design refinement, testing, and cost analysis would be necessary to fully assess commercial potential. The designs and test results will be communicated to the HVAC manufacturing community.

42 ENGINEERING↗

AI-Assisted Conceptual Development of a Pre-Geometric Cosmological Model - An Exercise in AI-Assisted Conceptual Framework Generation, Paper II: Local Geometry and Metric Structure

This paper develops the geometric sector of the replication-driven cosmogenesis framework introduced in Paper I. Starting from a pre-geometric spectral substrate and a minimal set of replication axioms, we show how coherent self-replicating units generate a spatial adjacency graph whose continuum limit acquires an effective Riemannian structure. The replication dynamics determines a characteristic correlation length that seeds the local metric, while overlap relations among coherent units produce an isotropic neighborhood geometry with an emergent dimensionality $d_{\rm eff}\simeq 3$ across a broad range of replication factors. As replication slows and causal order stabilizes, a limiting signal speed $c_\ast$ appears, providing the basis for the Lorentzian structure of spacetime without assuming a pre-existing light cone. We derive conditions under which the adjacency graph converges to a smooth three-dimensional manifold, describe the transition from Euclidean to Lorentzian propagation, and identify geometric invariants controlled by the replication parameters. This work establishes the geometric and causal layer of the replication cosmogenesis program, bridging the spectral axioms of Paper I to the cosmological dynamics explored in Paper III.

79 ASTRONOMY AND ASTROPHYSICS↗

Effect of Heat and Electricity Storage and Reliability on Microgrid Viability: A Study of Commercial Buildings in California and New York States

Berkeley Lab has for several years been developing methods for selection of optimal microgrid systems, especially for commercial building applications, and applying these methods in the Distributed Energy Resources Customer Adoption Model (DER-CAM). This project began with 3 major goals: (1) to conduct detailed analysis to find the optimal equipment combination for microgrids at a few promising commercial building hosts in the two favorable markets of California and New York, (2) to extend the analysis capability of DER-CAM to include both heat and electricity storage, and (3) to make an initial effort towards adding consideration of power quality and reliability (PQR) to the capabilities of DER-CAM. All of these objectives have been pursued via analysis of the attractiveness of a Consortium for Electric Reliability Technology Solutions (CERTS) Microgrid consisting of multiple nameplate 100 kW Tecogen Premium Power Modules (CM-100). This unit consists of an asynchronous inverter-based variable speed internal combustion engine genset with combined heat and power (CHP) and power surge capability. The essence of CERTS Microgrid technology is that smarts added to the on-board power electronics of any microgrid device enables stable and safe islanded operation without the need for complex fast supervisory controls. This approach allows plug and play development of a microgrid that can potentially provide high PQR with a minimum of specialized site-specific engineering. A notable feature of the CM-100 is its time-limited surge rating of 125 kW, and DER-CAM capability to model this feature was also a necessary model enhancement.

25 ENERGY STORAGE↗

Tool employing homotopy-based approaches in finding the controlling unstable equilibrium point in the electric power grid

The analysis tool employs a computer-implemented algorithm that uses homotopy-based approaches to map the solution from the exit point to the controlling unstable equilibrium point (UEP). The computational time is reduced significantly by using an approximate exit point rather than computing an accurate exit point as it is required in finding the controlling UEPs using traditional transient stability direct methods. In addition, this method eliminates the necessity of computing the minimum gradient point (MGP) which is a key element in using Newton methods. These properties provide an advantage to homotopy-based approaches over traditional iterative methods in terms of both speed of computation and reliability of finding solutions.

97 MATHEMATICS AND COMPUTING↗

Understanding the Spatiotemporal Variability of Tropical Orographic Rainfall Using Convective Plume Buoyancy

Abstract Mechanical forcing by orography affects precipitating convection across many tropical regions, but controls on the intensity and horizontal extent of the orographic precipitation peak and rain shadow remain poorly understood. A recent theory explains this control of precipitation as arising from modulation of lower-tropospheric temperature and moisture by orographic mechanical forcing, setting the distribution of convective rainfall by controlling parcel buoyancy. Using satellite and reanalysis data, we evaluate this theory by investigating spatiotemporal precipitation variations in six mountainous tropical regions spanning South and Southeast Asia, and the Maritime Continent. We show that a strong relationship holds in these regions between daily precipitation and a measure of convective plume buoyancy. This measure depends on boundary layer thermodynamic properties and lower-free-tropospheric moisture and temperature. Consistent with the theory, temporal variations in lower-free-tropospheric temperature are primarily modulated by orographic mechanical lifting through changes in cross-slope wind speed. However, winds directed along background horizontal moisture gradients also influence lower-tropospheric moisture variations in some regions. The buoyancy measure is also shown to explain many aspects of the spatial patterns of precipitation. Finally, we present a linear model with two horizontal dimensions that combines mountain wave dynamics with a linearized closure exploiting the relationship between precipitation and plume buoyancy. In some regions, this model skillfully captures the spatial structure and intensity of rainfall; it underestimates rainfall in regions where time-mean ascent in large-scale convergence zones shapes lower-tropospheric humidity. Overall, these results provide new understanding of fundamental processes controlling subseasonal and spatial variations in tropical orographic precipitation.

54 ENVIRONMENTAL SCIENCES↗

Spherically expanding flame in silane–hydrogen–nitrous oxide–argon mixtures

The effect of silane addition on the laminar flame speed ($S^0_u$) of flames propagating in hydrogen–nitrous oxide–argon mixtures has been investigated experimentally for the first time using the spherically expanding flame technique in a constant volume combustion chamber. Replacing hydrogen by silane and maintaining the equivalence ratio constant, much higher flame speeds, explosion peak pressures, and pressure rise coefficients were measured. A previously developed detailed reaction model has been updated based on ab initio thermodynamic properties calculations and collision limit violation analysis. The improved reaction model demonstrates encouraging performance in predicting the flame speed, with a mean absolute error below 11%. To explain the effect of silane addition on the flame dynamics, a number of parameters have been calculated including OH and H rate of production, heat release rate per reaction, and sensitivity coefficient on . The dynamics of freely propagating flames in SiH 4 –H 2 –N 2 O–Ar mixtures is essentially controlled by reactions of the H–O–N chemical system: N 2 O+H=N 2 +OH, OH+H 2 =H 2 O+H, and N 2 O(+M)=N 2 +O(+M). Whereas silane addition does not influence much the rate of production of OH, it significantly modifies that of H with a number of pyrolytic chemical pathways of silicon hydrides, such as SiH+H 2 =SiH 2 +H and Si+H 2 =SiH+H, which act as sink of H atom as they proceed in the backward direction. The reactions forming SiO(s) and SiO 2 (s), such as SiO+OH=SiO 2 (s)+H and 2SiO=2SiO(s), are exothermic and significantly contribute to the temperature increase. The adiabatic, constant pressure flame temperature for mixture containing silane is significantly higher, up to several 100’s K. The increase of induced by silane addition seems to be mostly related to the large increase of the flame temperature which leads to higher energy release rate.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Differential Power Processing for Ultra-Efficient Data Storage

Here this paper presents the hardware, software, and power codesign of an ultra-efficient data storage server with differential power processing (DPP). DPP can reduce the power conversion stress, improve the efficiency, and enhance the functionality of modular power electronics systems. The power inputs of a large number of hard disk drives (HDDs) were connected in series and supported by a multiport ac-coupled differential power processing (MAC-DPP) converter through a multiwinding transformer. Methods for controlling the multi-input multi-output power flow in the multiwinding transformer while avoiding core saturation were investigated. A ten-port MAC-DPP prototype with 700-W/in 3 power density was built to support a 450-W HDD storage system with ten series-stacked voltage domains. The prototype was tested on a 50-HDD server testbench, and the overall system loss is below 1 W (99.77% system efficiency). The server was able to maintain high-speed reading and writing operation of all 50 HDDs against the worst hot-swapping scenarios. A variety of hardware/software configurations and many cloud storage techniques were tested on the fully functioning server. Experimental results show that the energy efficiency of large-scale information systems (CPU/GPU clusters, memory banks, HDD arrays, etc.) can be greatly improved by software, hardware, and power codesign.

42 ENGINEERING↗

Dynamic shear localization of a titanium alloy under high-rate tension characterized by x-ray digital image correlation

Highlights: • First systematic error analyses for XDIC • First XDIC study of Ti-6Al-4V under dynamic tension • Deformation mode transition induces dynamic ductility decrease. • Dynamic shear localization due to rate-dependent microvoid coalescence process. - Abstract: Dynamic and quasi-static tension experiments are conducted on Ti-6Al-4V alloys, with in situ, synchrotron-based, high-speed, x-ray phase contrast imaging implemented to characterize the dynamic deformation and fracture process of Ti alloys at the Advanced Photon Source. X-ray digital imaging correlation (XDIC) is applied for strain field mapping. The size distribution of x-ray speckles are quantified via a morphological analysis, with a mean of ∼20 μm. Systematic error analyses of displacement and strain field measurements are firstly conducted for XDIC, and demonstrate that the displacement and strain errors can be controlled below 0.01 pixel and 0.1%, respectively. Mesoscale strain characteristics measured via XDIC are consistent with and reveal mechanisms for the bulk-scale stress–strain responses. Under dynamic tension, a sharp transition to strain softening occurs when the bulk strain exceeds about 0.04, which leads to a lower dynamic fracture strain (0.08) than the quasi-static one (0.1). The corresponding strain filed mapping demonstrates that shear deformation localizations grow and coalesce rapidly into a narrow shear deformation band under dynamic loading, while tensile deformation and necking progresses gradually under quasi-static loading. Scanning electron microscopy shows that void nucleation occurs mainly at the interface of α and β phases for both quasi-static and dynamic tension. However, microvoids coalesce preferentially along colony boundaries or the boundary α phase under quasi-static tension, but along the maximum shear stress direction (across colonies) under dynamic tension. Fractography of recovered samples also shows consistent features.

36 MATERIALS SCIENCE↗

A petascale direct numerical simulation study of the modelling of flame wrinkling for large-eddy simulations in intense turbulence

A new set of petascale direct numerical simulations (DNS) modelling lean hydrogen combustion with detailed chemistry in a temporally evolving slot-jet configuration is presented as a database for the development and validation of models for premixed turbulent combustion. The jet Reynolds number is 10,000, requiring grid numbers up to nearly seven billion, which was achieved by computation on 120,000 processor cores. In contrast to many prior DNS studies, a mean shear exists that drives strong turbulent mixing within the flame structure. Three cases are simulated with different Damköhler numbers, while Reynolds number is held fixed. Basic statistics are presented showing that integrated burning rates up to approximately six times the laminar burning rate are obtained. It is shown that increased flame surface area accounts for most of the enhanced burning while increases in the burning rate per unit area also play an important contribution. The database is then used to assess a new model of flame wrinkling intended for large-eddy simulations (LES). The approach draws on concepts from fractal geometry, requiring the modelling of an inner cut-off scale representing the smallest scale of flame wrinkling, and the fractal dimension controlling the resolution dependence of the unresolved flame surface area. In contrast to previous modelling, it is argued that the inner cut-off should be filter-size invariant in an inertial range. Then, dimensional and physical reasoning together with Damköhler’s limiting scaling laws for the turbulent flame speed are used to infer the cut-off and fractal dimension in limiting regimes. Two methods of determining the fractal dimension are proposed: a static, algebraic expression or a dynamic approach exploiting a Germano-type identity. Finally the model is compared against the DNS in a priori tests and is found to give excellent results, quantitatively capturing the trends with time, space, filter size and Damköhler number.

Energy & Fuels↗