Search NASA⌕ Search

SEARCH · Search NASA

Results for “TEST REACTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

Conceptual design of the LHCD system on CFETR

With the capability of saving flux consumption in the current ramp up phase, controlling the safety factor (q) profile, providing the required off-axis current drive (CD), a lower hybrid current drive (LHCD) system was eventually determined to be used on the China Fusion Engineering Test Reactor (CFETR). Here, in this paper, a 20 MW/4.6 GHz system composed of 40 units of 500 kW continuous wave (CW) klystron amplifier is preliminarily designed. The feasibility of the frequency choice of 4.6 GHz in the physical aspect is discussed. In order to minimize the transmission loss, a TE01 over-mode of circular waveguide will be used in the transmission system. Although previous calculations indicates that high field side (HFS) launcher location results in waves damping at inner region than low field side (LFS) launcher, which is favorable for plasma stability, HFS launcher will be extremely difficult in engineering due to the limited space. Calculations show that the tritium breeding ratio (TBR) will be decreased by ~ 1.5% with HFS launcher, while it will be decreased by ~ 0.22% only with LFS launcher. As a result, the LH power will be coupled to plasma from the top port at LFS. The designed passive active multi-junction (PAM) launcher is arranged in an array of 5 rows and 8 columns with the height of 1181 mm and the width of 794 mm. A shielding block with a thickness of 20 cm will be equipped around the feeding waveguides to protect the feeding waveguides and to prevent neutron leakage. A preliminary scheme of the remote maintenance for the LFS launcher is given. The modeling results shows that the density for optimum coupling is ~ 1.8 × 10 17 /m 3 , lower than the 4.6 GHz cut-off density n e_co = 2.6 × 10 17 /m 3 . Around this density, the power directivity (D p ) can be high as 71%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Supported molybdenum oxides for the aldol condensation reaction of acetaldehyde

The (retro-)aldol condensation reaction is an important chemical transformation in the upgrading of biomass-derived compounds into fuels and valuable specialty chemicals. In this study, we found that supported molybdenum oxide (MoO x ) catalysts were active and selective for the aldol condensation of acetaldehyde to crotonaldehyde under steady-state reactor conditions. Through a combination of transmission electron microscopy (TEM), ultraviolet–visible (UV–VIS) diffuse reflectance spectroscopy, Fourier transform infrared (FTIR) spectroscopy of adsorbed pyridine, and steady-state reactor testing, we determined that highly dispersed MoO x has a strong interaction with a γ-Al 2 O 3 support resulting in optimal catalyst performance at low weight loadings. In contrast, MoO x particles supported on SiO 2 have a weaker interaction with the support, resulting in a monotonic relationship between Mo loading and aldol condensation activity. The Lewis acid site density and strength are important parameters for predicting aldol condensation activity across all samples. The concentration of weak acid sites had a poor correlation with aldol condensation activity, most likely because these sites are too weak to activate acetaldehyde for the reaction. Medium and strong acid sites both had good correlations to aldol condensation activity. Results from X-ray absorption near edge structure (XANES) and acetaldehyde temperature programmed desorption (TPD) indicated that partially reduced MoO x was more active for aldol condensation, but pretreatment in reducing or oxidizing environments had no significant effect on steady-state catalytic activity. Finally, characterization of spent catalyst samples through temperature programmed oxidation (TPO) and thermogravimetric analysis (TGA) revealed that catalysts with high densities of strong acid sites tended to form more carbonaceous deposits on the surface over the course of the reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Phase Stability of an HT-9 Duct Irradiated in FFTF

A fuel test assembly known as ACO-3 duct made out of a fully tempered ferritic/martensitic steel (HT-9) was previously irradiated in the Fast Flux Test Reactor Facility (FFTF) up to 155 dpa at a temperature range of 380-504°C. The microstructures of the samples from 5 different zones along the face of the duct were analyzed using a combination of TEM based techniques, SANS and APT. A high density of Cr rich a' precipitates together with moderate density G-phase precipitates with an average sizes of 5 and 11 nm respectively were found at 20 dpa, 380°C zone. It was found that the precipitations of the second phases are more sensitive to temperature then the dose. In general, the density of both precipitates decreases with increasing irradiation temperature. No significant change is observed in average size of a' while the average size of G-phase precipitates increases up to 27 nm at 440°C. Voids are seen at 100 (410°C) and 155 (440°C) dpa zones but none was detected at 96 dpa (466°C) zone. In contrast to what is reported in the literature, no laves or Chi phases were found in any of the zones.

36 MATERIALS SCIENCE↗

Phase Development in a U-7 wt.% Mo vs. Al-7 wt.% Ge Diffusion Couple

Fuel development for the Reduced Enrichment for Research and Test Reactors (RERTR) program has demonstrated that U-Mo alloys in contact with Al develop interaction regions with phases that have poor irradiation behavior. The addition of Si to the Al has been considered with positive results. Compositional modification to replace Si with Ge is now under evaluation to attempt to further improve irradiation behavior. In this study, the microstructural and phase development of a diffusion couple of U-7 wt.% Mo in contact with Al-7 wt.% Ge was examined by transmission electron microscopy, scanning electron microscopy and energy dispersive spectroscopy. The interdiffusion zone developed a microstructure that included the cubic-UGe3 phase and amorphous phases. The UGe3 phase was observed with and without Mo and Al solid solutioning developing a (U,Mo)(Al,Ge)3 phase.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A cellular automaton method to simulate the microstructure and evolution of low-enriched uranium (LEU) U–Mo/Al dispersion type fuel plates

Low-enriched uranium (LEU) fuel plates for high power materials test reactors (MTR) are composed of nominally spherical uranium-molybdenum (U-Mo) particles within an aluminum matrix. Fresh U-Mo particles typically range between 10 and 100 mu m in diameter, with particle volume fractions up to 50%. As the fuel ages, reaction-diffusion processes cause the formation and growth of interaction layers that surround the fuel particles. The growth rate depends upon the temperature and radiation environment. The cellular automaton algorithm described in this paper can synthesize realistic random fuel-particle structures and simulate the growth of the intermetallic interaction layers. Examples in the present paper pack approximately 1000 particles into three-dimensional rectangular fuel structures that are approximately 1 mm on each side. The computational approach is designed to yield synthetic microstructures consistent with images from actual fuel plates and is validated by comparison with empirical data on actual fuel plates. (C) 2014 Elsevier B.V. All rights reserved.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Mechanical properties examined by nanoindentation for selected phases relevant to the development of monolithic uranium-molybdenum metallic fuels

Nanomechanical properties, specifically the reduced modulus and hardness of several intermetallic and solid solution phases are reported here to assist the development of the U-10 wt% Mo (U-10Mo) monolithic fuel system for research and test reactors. Findings from this study and reported values of mechanical properties provide data critical for understanding and predicting the structural behavior of the fuel system during fabrication and irradiation. The phases examined are products of interdiffusion and reaction between (1) the AA6061 cladding and the Zr diffusion barrier, namely (Al,Si) 3 Zr and Al 3 Zr, (2) the U-10Mo fuel and the Zr diffusion barrier, namely UZr 2 , Mo 2 Zr, and a-U, and (3) the U (or U-10Mo) and Mo, namely a mixture gradient of α- and γ-phases. The UC inclusions observed within the fuel alloy were also examined. Only phases present in thick or continuous microstructure on cross-sectioned fuel plates and diffusion couples were investigated for reduced modulus and hardness. Concentration-dependence of room-temperature reduced modulus in U solid solution with 0–10 wt% Mo was semi-quantitatively modeled based on mixture of α- and γ-phases and solid solutioning within the γ-phase.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Accelerated materials evaluation for nuclear applications

This report addresses the opportunities and complexities of using materials test reactors with high neutron fluxes to perform accelerated studies of material aging in power reactors operating at lower neutron fluxes and with different neutron flux spectra. Radiation damage and gas production in different reactors have been compared using the code, SPECTER. This code provides a common standard from which to compare neutron damage data generated by different research groups using a variety of reactors.

36 MATERIALS SCIENCE↗

Micro to nanostructural observations in neutron irradiated nuclear graphites PCEA and PCIB

Here, the neutron irradiation induced structural changes in nuclear grade graphites PCEA and PCIB were investigated using scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman spectroscopy, transmission electron microscopy (TEM), selected area electron diffraction (SAED) and electron energy loss spectroscopy (EELS). The graphite samples were irradiated at the Advanced Test Reactor National User Facility at the Idaho National Laboratory. Received doses ranged from 1.5 dpa - 6.8 dpa and irradiation temperatures varied between 350°C - 670°C. XRD data showed crystallite sizes to reduce by 35% (for both La and Lc) for low dose, low temperature specimens and by 50% (for both La and Lc) for high dose, high temperature specimens (compared to unirradiated specimens of the same grade). Analysis of the G peak in Raman spectra of irradiated specimens provided evidence for the fragmentation of crystallites following neutron irradiation. Conventional TEM and SAED were used to observe the structure of lattice fringes and measure the spacing of planes. Image analysis software was applied to TEM images to quantify fringe length, tortuosity, and relative orientation of planes. Neutron irradiation appeared to induce basal plane fragmentation and curvature. EELS was performed to study the proportion of sp2 bonding and specimen density. The high dose high temperature specimens showed evidence of structural recovery where sp2 values are slightly higher than values associated with low dose low temperature specimens. Data from XRD, Raman, TEM, SAED and EELS showed that low dose low temperature specimens tended to exhibit higher structural damage (such as lower sp2 content, higher d-spacing, and reduced crystallite size) than high dose high temperature specimens.

36 MATERIALS SCIENCE↗

Microstructural evolution of neutron-irradiated T91 and NF616 to ~4.3 dpa at 469 °C

Ferritic-martensitic steels such as T91 and NF616 are candidate materials for several nuclear applications. Here, this study evaluates radiation resistance of T91 and NF616 by examining their microstructural evolutions and hardening after the samples were irradiated in the Advanced Test Reactor to ~4.3 displacements per atom (dpa) at an as-run temperature of 469 °C. In general, this irradiation did not result in significant difference in the radiation-induced microstructures between the two steels. Compared to NF616, T91 had a higher number density of dislocation loops and a lower level of radiation-induced segregation, together with a slightly higher radiation-hardening. Unlike dislocation loops developed in both steels, radiation-induced cavities were only observed in T91 but remained small with sub-10 nm sizes. Lastly, other than the relatively stable M 23 C 6 , a new phase (likely Sigma phase) was observed in T91 and radiation-enhanced MX → Z phase transformation was identified in NF616. Laves phase was not observed in the samples.

36 MATERIALS SCIENCE↗

TEM characterization of irradiated U-7Mo/Mg dispersion fuel

This paper presents the results of transmission electron microscopy (TEM) characterization on neutron-irradiated samples taken from the low-flux and high-flux sides of the same fuel plate with U-7Mo fuel particles dispersed in Mg matrix with aluminum alloy Al6061 as cladding material that was irradiated edge-on to the core in the Advanced Test Reactor. The corresponding local fission density and fission rate of the fuel particles and the average fuel-plate centerline temperature for the low-flux and high-flux samples are estimated to be 3.7 × 10 21 f/cm 3 , 7.4 × 10 14 f/cm 3 /s and 123 °C, and 5.5 × 10 21 f/cm3, 11.0 × 10 14 f/cm 3 /s and 158 °C, respectively. Complex interaction layers developed at the Al-Mg interface, consisting of Al 3 Mg 2 and Al 12 Mg 17 along with precipitates of MgO, Mg 2 Si and FeAl 5.3 . No interaction between Mg matrix and U-Mo fuel particle was identified. For the U-Mo fuel particles, at low fission density, small elongated bubbles wrapped around the clean areas with a fission gas bubble superlattice, which suggests that bubble coalescence is an important mechanism for converting the fission gas bubble superlattice to large bubbles. At high fission density, no bubbles or porosity were observed in the Mg matrix, and pockets of residual fission gas bubble superlattice were observed in the U-Mo fuel particle interior.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Detailed measurements of local thickness changes for U-7Mo dispersion fuel plates with Al-3.5Si matrix after irradiation at different powers in the RERTR-9B experiment

The Materials Management and Minimization program is developing fuel designs to replace highly enriched fuel with fuels of low enrichment. Swelling is an important irradiation behavior that needs to be well understood. Data from high resolution thickness measurements performed on U-7Mo dispersion fuel plates with Al-Si alloy matrices that were irradiated at high power is sparse. This paper reports the results of detailed thickness measurements performed on two dispersion fuel plates that were irradiated at relatively high power to high fission densities in the Advanced Test Reactor in the same RERTR-9B experiment. Both plates were irradiated to similar fission densities, but one was irradiated at a higher power than the other. The goal of this work is to identify any differences in the swelling behavior when fuel plates are irradiated at different powers to the same fission densities. Based on the results of detailed thickness measurments, more swelling occurs when a U-7Mo dispersion fuel with Al-3.5Si matrix is irradiated to a high fission density at high power compared to one irradiated at a lower power to high fission density.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Corrigendum to “Accelerated materials evaluation for nuclear applications” [J. Nucl. Mater. 488 (2017) 46–62]

The original article addresses the opportunities and complexities of using materials test reactors with high neutron fluxes to perform accelerated studies of material aging in power reactors operating at lower neutron fluxes and with different neutron flux spectra. Radiation damage and gas production in different reactors have been compared using the code, SPECTER. This code provides a common standard from which to compare neutron damage data generated by different research groups using a variety of reactors. This Corrigendum identifies a few typographical errors. Tables 2 and 3 are included in revised form.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermal conductivity measurement of the interaction layer between UMo and Al produced by high-energy heavy ion irradiation

In this work, we report the first direct thermal conductivity measurement results for Al-UMo interaction layer (IL), which is typically observed in UMo/Al dispersion fuel plates under irradiation. The investigated IL was formed by irradiating Al coated UMo substrate using 80 MeV iodine ions at 180 degrees C up to 3.03 x 10 17 ions/cm 2 fluence. Microstructural characterization indicated that the induced IL is amorphous with an approximately (U 0.8 ,Mo 0.2 )Al 5.3 stoichiometry, which is similar to that formed under in-pile irradiation. Focused ion beam (FIB) was used to prepare nine specimens of various lengths from the IL that could be suspended across a microfabricated device for thermal conductivity measurement. The measured thermal conductivity values of the IL were significantly lower than the values for both the original UMo fuel and the Al. The successful measurement of the Al-UMo IL provides valuable information for the development and qualification of UMo/Al dispersion fuels for research and test reactor conversion applications, and further demonstrates the promising capabilities of utilizing the suspended bridge method in nuclear fuel research.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

α-U and ω-UZr 2 in neutron irradiated U-10Zr annular metallic fuel

Here, to develop metallic fuel with ultra-high burnup of 30%-40%, an annular U-10Zr fuel with 55% smear density was fabricated through a casting route and irradiated at the Advanced Test Reactor at Idaho National Laboratory. The annular fuel design also serves as a demonstration of the feasibility to replace sodium bond with a helium bond to benefit the geological disposal of irradiated fuel, cut the cost of fuel fabrication, and boost the overall metallic fuel economy. This paper reports the results from transmission electron microscopy (TEM) based post-irradiation examination of this fuel type irradiated to a burnup of 3.3% fissions per initial heave metal atoms for initial screening purpose. After irradiation, the initial U-10Zr separated into an a-U annular region and an UZr 2+x center region with nanoscale spinodal decomposed microstructure. Because of the provided large amount of coherent interface areas, the fission gas atoms and vacancies generated in UZr 2+x phase are possibly pinned at the interface areas, leading to 20 times smaller fission gas bubbles than those in the neighboring a-U. The large bubbles in a-U become connected and merged into large pores that provide fast release paths for fission gas which prevents further fuel swelling. The fuel center still has open space to accommodate further fuel swelling from solid fission products at higher burnup. Other neutron irradiation induced phase and microstructure change are also characterized and compared with traditional solid fuel designs.

36 MATERIALS SCIENCE↗

Impact of neutron irradiation on the thermophysical properties of additively manufactured stainless steel and inconel

The deployment of additive manufacturing (AM) technologies to support the nuclear energy industry is limited by the current lack of data related to the irradiation performance of AM parts. The Colorado School of Mines is conducting a multi-year irradiation and post irradiation examination project to study the impacts of neutron irradiation on stainless steel 316L and Inconel 718 and 625 specimens produced by several commercially available AM techniques and irradiated in the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL). This paper presents initial results on the impact of neutron irradiation on the heat capacity, the thermal diffusivity, and the thermal conductivity of the specimens at temperatures between 100 oC and 400 oC. The unirradiated AM specimens have heat capacity values similar to, or lower than, the reference values, regardless of manufacturing method or material. The irradiated AM specimens have average heat capacities greater than the unirradiated specimens and reference values in every case. Additionally, the thermal diffusivities of the unirradiated AM specimens are either larger or statistically similar to the reference values. The irradiated AM specimens exhibit lower thermal diffusivities compared to the reference thermal diffusivity values. One of the stainless steel 316L laser powder bed fusion samples exhibited thermal diffusivity values with statistically significant anisotropy prior to and after irradiation. The thermal conductivities of the unirradiated AM stainless steel 316L specimens and the unirradiated Inconel 718 specimens are lower or statistically similar to the reference values. The unirradiated Inconel 625 specimens exhibit slightly higher thermal conductivity values than the reference values. The irradiated specimens show a significant increase in thermal conductivity compared to the unirradiated specimens and the reference values for all materials.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Evaluation of the anisotropic grain boundaries and surfaces of α -U via molecular dynamics

Alloys based on uranium-zirconium are gaining renewed interest as fuels for the Versatile Test Reactor and a number of microreactor designs. Implementing metallic fuel in reactors creates the need for robust descriptive and predictive fuel performance modeling. Here, the current state of metallic fuel performance modeling relies on empirical equations derived from historical experiments, which may be unreliable when applied outside of their temperature, power, and composition phase space. One area where such data is lacking is the irradiation behavior of alpha -U, specifically tearing and porosity formation at the early stages of irradiation. While grain boundaries likely play a key role in this fuel behavior, relatively little is known about grain boundaries in alpha-U. Thus, we evaluate the grain boundary, surface energy, and work of adhesion of alpha -U utilizing molecular dynamics. Symmetric tilt grain boundaries (STGBs) are analyzed with the tilt plane oriented along each major crystallographic axis, for a total of eighty unique grain boundaries. The effect of temperature, tilt plane, and misorientation angle on interfacial energies are analyzed. The interfacial energies typically increase with temperature and there is significant variance as a function of misorientation angle, irrespective of the tilt plane. At 500 K, the average surface energy (1.23 J/m 2 ) is approximately 1.5 times the grain boundary energy (0.79 J/m 2 ), and the work of adhesion is approximately twice the grain boundary energy (1.68 J/m 2 ). Orientations for the likely formation of twins and likely failure planes are identified.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗