Search NASA⌕ Search

SEARCH · Search NASA

Results for “VAPOR PHASE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

2D-EFICACY: Control of Metastable 2D Carbide[1]Chalcogenide Heterolayers: Strain and Moire Engineering

The experimental isolation of graphene led to the discovery of an entirely new world of two-dimensional (2D) materials in which the 2D nature often leads to emergent behaviors not seen in bulk systems. 2D transition metal dichalcogenides (TMDs) exhibit physico-chemical properties that depend on the transition metal, polymorph, thickness, and presence and type of defects. Recently, a group of thin (10-100nm) transition metal carbides (TMCs), such as Mo2C, has been synthesized that exhibit a thickness-dependent superconducting critical temperature (Tc). These thin TMCs are different from MXenes, another class of 2D materials consisting of few layers of nitrides or carbides (<5nm) produced by chemical etching and delamination. The goal of this renewal proposal is to combine experiment and computation to synthesize and elucidate the guiding principles that control the growth, orientation and strain of heterostacks of thin TMCs and TMDs composed with Nb, Ti and W. We expect to stabilize metastable hybrid phases of TMCs sandwiched between TMDs (H-TMD/Cs) with unprecedented physico-chemical properties. As part of previous DOE-funded work by the Terrones/Sinnott groups, thin (10-100 nm thick) Mo2C flakes were successfully synthesized by chemical vapor deposition (CVD). By subsequently exposing Mo2C to H2S, partial chalcogenization was achieved, resulting in heterostacks of MoCx phases and MoS2. The formation of MoS2 led to a deficiency of Mo atoms in the underlying Mo2C, resulting in an inhomogeneous phase change from α-Mo2C to γ’-MoCx and then to γ-MoC. The γ’-MoCx is a strained metastable phase and the heterostack of all three phases demonstrated an increased Tc relative to that of α-Mo2C, from 4 to 6K; its interleaved layered structure consisting of superconducting and semiconducting phases is ideal for future studies of Josephson junction series arrays. Moiré patterns in these heterostacked systems could result in new phenomena, as moiré patterns in bilayer graphene showed unconventional superconductivity and moiré excitons have been observed in twisted TMD heterobilayers. The scientific hypothesis of the proposed synergistic computational and experimental research is that orientation and strain control within confined thin metastable TMCs, sandwiched by stable phases of TMCs and layered TMDs, will depend on kinetic and thermodynamic “knobs” that include fast temperature changes, chalcogen diffusion through preferred crystallographic planes, reaction times, pressure, reactive atmosphere, precursors, and surfactants, which will also tailor properties such as superconductivity, magnetism, ferroelectricity, piezoelectricity, and catalytic performance. We will develop the guiding principles for the synthesis and stabilization of metastable H-TMD/Cs based on Nb, Ti and W. In order to validate the hypothesis, four tasks are proposed: The first task will synthesize ultra-thin TMCs based on Nb, W and Ti, by: 1) adapting the CVD method used for Mo2C, 2) plasma assisted CVD, 3) defect-mediated CVD processes, and 4) cryo-milling of carbide powders. The second task will accomplish the synthesis and basic physico-chemical characterizations of H-TMD/Cs by chalcogenization of the materials synthesized in task one, and by carbonization of TMDs. H-TMD/Cs will also be investigated for their suitability in energy conversion applications such as supercapacitors, Li and multivalent ion batteries, and electrocatalysts, topics of interest to DoE. These tasks will be carried out in close conjunction with density functional theory (DFT) calculations with insights into energetics, lattice parameters, stability, phase diagrams, band structures, and density of states of H-TMD/Cs. The third task will characterize and evaluate strain and moiré patterns at the interfaces of different H-TMD/Cs by high-resolution scanning transmission electron microscopy (HR-STEM), scanning tunneling microscopy (STM), and conductive tip atomic force microscopy. Nudged elastic band calculations with DFT will be performed to understand the chalcogen diffusion process, which will provide insights into the interfaces between different phases of TMCs and TMDs. The fourth task aims at quantifying the stability and dynamics of H-TMD/Cs by in-situ TEM and Raman studies under heating, strain, and electrical biasing. Phonon calculations using DFT will provide a basis for interpreting Raman spectra. This coherent framework involving synthesis, characterization, and computation will result in a broad scientific impact for energy related applications. The ability to develop new H-TMD/Cs will enhance a range of applications that include batteries, catalysts, switches, sensors, quantum computing components and smart coatings.

2-Dimensional materials↗

Growth and Isolation of Large Area Boron-Doped Nanocrystalline Diamond Sheets: A Route toward Diamond-on-Graphene Heterojunction

Many material device applications would benefit from thin diamond coatings, but current growth techniques, such as chemical vapor deposition (CVD) or atomic layer deposition require high substrate and gas-phase temperatures that would destroy the device being coated. The development of freestanding, thin boron-doped diamond nanosheets grown on tantalum foil substrates via microwave plasma-assisted CVD is reported. These diamond sheets (measuring up to 4 × 5 mm in planar area, and 300–600 nm in thickness) are removed from the substrate using mechanical exfoliation and then transferred to other substrates, including Si/SiO 2 and graphene. The electronic properties of the resulting diamond nanosheets and their dependence on the free-standing growth, the mechanical exfoliation and transfer processes, and ultimately on their composition are characterized. To support this, a prototypical diamond nanosheet–graphene field effect transistor-like (DNGfet) device is developed and its electronic transport properties are studied as a function of temperature. The resulting DNGfet device exhibits thermally activated transport (thermionic conductance) above 50 K. Below 50 K a transition to variable range hopping is observed. Finally, these findings demonstrate the first step towards a low-temperature diamond-based transistor.

36 MATERIALS SCIENCE↗

Development of an Experimental Approach for Thermal Testing in Bedded Salt - 19431

Safe and permanent isolation of used nuclear fuel (UNF) and high-level nuclear waste (HLW) is an integral component of the cradle-to-grave philosophy of radioactive waste management. Out of the multitude of rock types considered for the permanent deep disposal of nuclear waste (tuff, shale, granite, clay, and salt), salt has received significant interest particularly because of the advantage offered by salt as an impermeable and dry medium with self-sealing properties. The concept of HLW disposal in salt has been investigated through several testing campaigns in the U.S. and in Germany. Serval knowledge gaps still exist in our understanding of how brine is generated and how it transports under heat generating conditions. These knowledge gaps limit our ability to build a robust safety case for the disposal of heat generating waste in salt. The current manuscript reports on efforts performed to develop a field-testing campaign to study brine and water vapor migration in heated salt. The paper summarizes initial work done in a phased thermal testing program in bedded salt at the Waste Isolation Pilot Plant (WIPP), Carlsbad, New Mexico. The testing to date has been focused on existing boreholes and is being used to 'shakedown' the process for implementation of a more refined testing program that will be implemented in freshly drilled boreholes planned for FY2019. We designed and deployed a heater assembly that consisted of a packer, borehole deformation gauge, heater block, a network of thermocouples, and a pressure transducer setup to measure in situ temperature and pressure. The assembly was deployed in an existing borehole and several heating and cooling experiments were performed to test the performance of the different instruments fielded. We report on the results obtained for brine generation as a function of time and heating and cooling cycles and temperature evolution in the rock salt. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Non-Contact Vapor Detection of Illicit Drugs via Atmospheric Flow Tube-Mass Spectrometry

Real-time, non-contact detection of illicit drugs is a desirable goal for the interdiction of these controlled substances, but the relatively low vapor pressures of such species present a challenge for trace vapor detection technologies. The introduction of atmospheric flow tube-mass spectrometry (AFT-MS), which has previously been demonstrated to detect gas-phase analytes at low parts-per-quadrillion levels for explosives and organophosphorus compounds, also enables the potential for non-contact drug detection. With AFT-MS, direct vapor detection of cocaine and methamphetamine from ~5 µg residues at room temperature is demonstrated herein. Furthermore, thermal desorption of low- to sub-picogram levels of cocaine, methamphetamine, fentanyl, and heroin is observed via AFT-MS using a carrier flow rate of several L/min of air. These low levels can permit non-contact sampling through collection of vapor, effectively preconcentrating the analyte before desorption and analysis. Quantitative evaluation of the thermal desorption approach has yielded limits of detection (LODs) on order of 10 fg for cocaine and fentanyl, 100 fg for methamphetamine, and 1.6 pg for heroin. The LOD for heroin was lowered to 200 fg by using tributyl phosphate as a dopant to form a proton-bound heterodimer with heroin. When used with AFT-MS, the intentional formation of specific drug-dopant adducts has the potential to enhance detection limits and selectivity of additional drug species. Species that are prone to form adducts present a challenge to analysis, but that difficulty can be overcome by the intentional addition of a dopant. Molecules unlikely to form adducts will remain essentially unimpacted, but the adduct-forming species will interact with the dopant to compress the analyte signal into a single peak. This approach would be valuable in the application of non-contact screening for illicit substances via vapor collection followed by thermal desorption for analysis.

methamphetamine, cocaine, heroin, fentanyl, atmosp↗

Tunable Magnetic Transition to a Singlet Ground State in a 2D van der Waals Layered Trimerized Kagomé Magnet

Incorporating magnetism into two-dimensional (2D) van der Waals (vdW) heterostructures is crucial for the development of functional electronic and magnetic devices. Here, we show that Nb 3 X 8 (X = Cl, Br) is a family of 2D layered trimerized kagomé magnets that are paramagnetic at high temperatures and undergo a first-order phase transition on cooling to a singlet magnetic state. X-ray diffraction shows that a rearrangement of the vdW stacking accompanies the magnetic transition, with high- and low-temperature phases consistent with scanning transmission electron microscopy images of the end members α-Nb 3 Cl 8 and β-Nb 3 Br 8 . The temperature of this transition is systematically varied across the solid solution Nb 3 Cl 8–x Br x (x = 0–8), with x = 6 having transitions near room temperature. Furthermore, the solid solution also varies the optical properties, which are further modulated by the phase transition. As such, they provide a platform on which to understand and exploit the interplay between dimensionality, magnetism, and optoelectronic behavior in vdW materials.

2D materials↗

Novel 1D coordination polymer {l_brace}Tm(Piv){sub 3{r_brace}n}: Synthesis, structure, magnetic properties and thermal behavior

The new 1D coordination polymer {l_brace}Tm(Piv){sub 3{r_brace}n} (1), where Piv=OOCBu{sup t-}, was synthesized in high yield (>95%) by the reaction of thulium acetate with pivalic acid in air at 100 Degree-Sign S. According to the X-ray diffraction data, the metal atoms in compound 1 are in an octahedral ligand environment unusual for lanthanides. The magnetic and luminescence properties of polymer 1, it's the solid-phase thermal decomposition in air and under argon, and the thermal behavior in the temperature range of -50 Horizontal-Ellipsis +50 Degree-Sign S were investigated. The vaporization process of complex 1 was studied by the Knudsen effusion method combined with mass-spectrometric analysis of the gas-phase composition in the temperature range of 570-680 K. - Graphical Abstract: Novel 1D coordination polymer {l_brace}Tm(Piv){sub 3{r_brace}n} was synthesized and studied by X-ray diffraction. The magnetic, luminescence properties, the thermal behavior and the volatility for the compound {l_brace}Tm(Piv){sub 3{r_brace}n} were investigated. Black-Small-Square Highlights: Black-Right-Pointing-Pointer We synthesized the coordination polymer {l_brace}Tm(Piv){sub 3{r_brace}n}. Black-Right-Pointing-Pointer Tm atoms in polymer have the coordination number 6. Black-Right-Pointing-Pointer Polymer exhibits blue-color emission at room temperature. Black-Right-Pointing-Pointer Polymer shows high thermal stability and volatility. Black-Right-Pointing-Pointer Polymer has no phase transitions in the range of -50 Horizontal-Ellipsis +50 Degree-Sign S.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thermodynamic analysis of the stability of planar interfaces between coexisting phases and its application to supercooled water

Two-phase simulations are commonly used to evaluate coexistence conditions, interfacial tensions, and other thermodynamic properties associated with first-order phase transitions. Calculation of these properties is often simplified when the interfaces between the two phases are flat or planar. In this paper, we derive a general thermodynamic criterion for selecting simulation cell dimensions to stabilize planar interfaces in phase-separated fluid-fluid systems with respect to homogeneous, single-phase states. The resulting expression is validated by analyzing the effects of simulation cell dimensions on the formation of planar liquid-vapor interfaces in the Lennard-Jones fluid and in the TIP4P/2005 model of water. We also perform large scale molecular dynamics simulations to study metastable liquid-liquid phase separation in the ST2 and TIP4P/2005 models of water under deeply supercooled conditions. Our simulations confirm the stability of a liquid-liquid interface in ST2, and they demonstrate that the corresponding interface for TIP4P/2005 can be stabilized by judiciously choosing the simulation cell aspect ratio in a manner consistent with the thermodynamic criterion. We posit that this sensitivity to the simulation cell aspect ratio may explain discrepancies between previous studies examining liquid-liquid separation in models of supercooled water.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of higher water vapor content on TBC performance

Coal gasification, or IGCC (integrated gasification combined cycle), is one pathway toward cleaner use of coal for power generation with lower emissions. However, when coal-derived synthesis gas (i.e., syngas) is burned in turbines designed for natural gas, turbine manufacturers recommend 'derating,' or lowering the maximum temperature, which lowers the efficiency of the turbine, making electricity from IGCC more expensive. One possible reason for the derating is the higher water vapor contents in the exhaust gas. Water vapor has a detrimental effect on many oxidation-resistant high-temperature materials. In a turbine hot section, Ni-base superalloys are coated with a thermal barrier coating (TBC) allowing the gas temperature to be higher than the superalloy solidus temperature. TBCs have a low thermal conductivity ceramic top coating (typically Y{sub 2}O{sub 3}-stabilized ZrO{sub 2}, or YSZ) and an oxidation-resistant metallic bond coating. For land-based gas turbines, the industry standard is air plasma sprayed (APS) YSZ and high velocity oxygen fuel (HVOF) sprayed NiCoCrAlY bond coatings. To investigate the role of higher water vapor content on TBC performance and possible mitigation strategies, furnace cycling experiments were conducted in dry O{sub 2} and air with 10% (typical with natural gas or jet fuel) or 50 vol% water vapor. Cycle frequency and temperature were accelerated to one hour at 1100 C (with 10 minute cooling to {approx}30 C between each thermal cycle) to induce early failures in coatings that are expected to operate for several years with a metal temperature of {approx}900 C. Coupons (16 mm diameter x 2 mm thick) of commercial second-generation single crystal superalloy CMSX4 were HVOF coated on both sides with {approx}125 {micro}m of Ni-22wt%Co-17Cr-12Al either with 0.7Y or 0.7Y-0.3Hf-0.4Si. One side was then coated with 190-240 {micro}m of APS YSZ. Coatings were cycled until the YSZ top coating spalled. Figure 2 shows the results of the initial phase of experiments. Compared to dry O{sub 2}, the addition of 10% water vapor decreased the lifetime of MCrAlY by {approx}30% for the conventional CMSX4 substrates. Higher average lifetimes were observed with Hf in the bond coating, but a similar decrease in lifetime was observed when water vapor was added. The addition of Y and La to the superalloy substrate did not change the YSZ lifetime with 10% water vapor. However, increasing water vapor content from 10 to 50% did not further decrease the lifetime of either bond coating with the doped superalloy substrate. Thus, these results suggest that higher water vapor contents cannot explain the derating of syngas-fired turbines, and other factors such as sulfur and ash from imperfect syngas cleanup (or upset conditions) need to be explored. Researchers continue to study effects of water vapor on thermally grown alumina scale adhesion and growth rate, and are looking for bond coating compositions more resistant to oxidation in the presence of water vapor.

01 COAL, LIGNITE, AND PEAT↗

Electron microscopic evidence for a tribologically induced phase transformation as the origin of wear in diamond

Tribological testing of a coarse-grained diamond layer, deposited by plasma-enhanced chemical vapor deposition, was performed on a ring-on-ring tribometer with a diamond counterpart. The origin of the wear of diamond and of the low friction coefficient of 0.15 was studied by analyzing the microstructure of worn and unworn regions by transmission and scanning electron microscopy. In the worn regions, the formation of an amorphous carbon layer with a thickness below 100 nm is observed. Electron energy loss spectroscopy of the C-K ionization edge reveals the transition from sp{sup 3}-hybridized C-atoms in crystalline diamond to a high fraction of sp{sup 2}-hybridized C-atoms in the tribo-induced amorphous C-layer within a transition region of less than 5 nm thickness. The mechanically induced phase transformation from diamond to the amorphous phase is found to be highly anisotropic which is clearly seen at a grain boundary, where the thickness of the amorphous layer above the two differently oriented grains abruptly changes.

36 MATERIALS SCIENCE↗

Detailed Reaction Kinetics for CFD Modeling of Nuclear Fuel Pellet Coating for High Temperature Gas-Cooled Reactors

The research project was related to the Advanced Fuel Cycle Initiative and was in direct alignment with advancing knowledge in the area of Nuclear Fuel Development related to the use of TRISO fuels for high-temperature reactors. The importance of properly coating nuclear fuel pellets received a renewed interest for the safe production of nuclear power to help meet the energy requirements of the United States. High-temperature gas-cooled nuclear reactors use fuel in the form of coated uranium particles, and it is the coating process that was of importance to this project. The coating process requires four coating layers to retain radioactive fission products from escaping into the environment. The first layer consists of porous carbon and serves as a buffer layer to attenuate the fission and accommodate the fuel kernel swelling. The second (inner) layer is of pyrocarbon and provides protection from fission products and supports the third layer, which is silicon carbide. The final (outer) layer is also pyrocarbon and provides a bonding surface and protective barrier for the entire pellet. The coating procedures for the silicon carbide and the outer pyrocarbon layers require knowledge of the detailed kinetics of the reaction processes in the gas phase and at the surfaces where the particles interact with the reactor walls. The intent of this project was to acquire detailed information on the reaction kinetics for the chemical vapor deposition (CVD) of carbon and silicon carbine on uranium fuel pellets, including the location of transition state structures, evaluation of the associated activation energies, and the use of these activation energies in the prediction of reaction rate constants. After the detailed reaction kinetics were determined, the reactions were implemented and tested in a computational fluid dynamics model, MFIX. The intention was to find a reduced mechanism set to reduce the computational time for a simulation, while still providing accurate results. Furthermore, fast chemistry techniques would be coupled to MFIX to effectively treat the complex chemistry thus improve the computational efforts. Based on the reaction kinetics modeling, it was determined that the detailed set of chemical reactions for the thermal decomposition of a methyltrichlorosilane (MTS)/H2 mixture consisted of 45 species and 114 gas-phase reactions. Further work identified a mechanism consisting of approximately 60 surface reactions for the surface chemistry of SiC chemical vapor deposition. A reduced mechanism for the MTS gas-phase pyrolysis was constructed using the scanning method based on optimization concepts, which consisted of only 28 species and 29 reactions. The benefits of this project are that we have determined gas-phase species produced during and after the various decomposition reactions of MTS. The success of the computational approaches can now be used to predict the complex chemistry associated with the CVD process in producing nuclear fuel. It is expected that the knowledge we acquired can be easily transferred and that it will contribute to further experimental investigations. Furthermore, the computational techniques can now be used for reactor design and optimization for the next generation of nuclear reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Suppressing Phase Segregation and Improving Stability in Mixed-Halide Perovskites through Spinel Oxide-Directed Epitaxy

Mixed-cation mixed-halide perovskite compositions are essential for achieving the required bandgaps for high-efficiency multijunction photovoltaics, yet their stability remains limited by interfacial defects, phase segregation, and degradation. Here, we introduce spinel oxides as a new family of lattice-matched substrates that enable crystalline, phase-pure, compositionally-uniform, bromide-rich perovskite film growth. The effect of spinel oxides is two-fold: reducing defects at the bottom interface by templating film growth and inducing beneficial compressive strain through mismatch-dependent substrate-perovskite lattice coupling. Spinel oxide substrates facilitate growth of highly crystalline films and eliminate detrimental secondary phases across thicknesses. Using grazing incidence X-ray diffraction, X-ray fluorescence, cathodoluminescence–scanning electron microscopy, cryogenic photoluminescence, and density functional theory, we reveal that Mg-halide bonds at the bottom interface induce lattice mismatch-dependent compressive strain that suppresses halide segregation and further reduces defect formation. In addition, films grown on spinel oxides maintain over 87% of the perovskite phase after 12 h under 100% relative humidity, as monitored by in situ grazing incidence wide-angle X-ray scattering (GIWAXS), compared to less than 70% for control samples. This work extends lattice matching from vapor-deposited epitaxial semiconductors to solution-processed halide perovskites to establish a broadly applicable strategy for defect suppression, phase homogenization, and long-term stability. Based on the fundamental science explored here, we set the stage for the development of lattice-matched spinel oxide charge transport layers to be integrated into perovskite solar cells and other optoelectronic devices.

36 MATERIALS SCIENCE↗

A new way of phase identification, of AgGaGeS{sub 4}∙nGeS{sub 2} crystals

The phase identification of AgGaGeS{sub 4}·nGeS{sub 2} (n=0–4) crystals grown by vertical Bridgman–Stockbarger technique was carried out to find the boundary value n between a homogeneous solid solution and its mixture with GeS{sub 2}. To obtain reliable results, the conventional methods of X-ray diffraction (XRD) and energy dispersive X-ray spectroscopy (EDX) were completed by less common vapor pressure measurement in a closed volume and precise density measurements, which are very sensitive to the detection of small amounts of crystalline and glassy GeS{sub 2} and heterogeneous state of the crystals. The boundary value n=1.5 at 1045 K and the coexistence of the solid solution AgGaGeS{sub 4}·1.5GeS{sub 2} with the β-GeS{sub 2} phase for n>1.5 was found. Glassy GeS{sub 2} (∼2 mol%) was revealed by vapor pressure measurement and XRD studies in all the crystals. This is discussed in terms of the supersaturated solid solution decomposition upon temperature decreasing and the microphase separation of overcooled melt near the melting point under non-equilibrium crystallization. For the first time, the p–T dependence for glassy GeS{sub 2} was measured by the vapor pressure measurements. - Graphical abstract: lg p–1/T dependences of as-grown AgGaGeS{sub 4}·nGeS{sub 2} crystals. - Highlights: • Vapor pressure measurement as a powerful tool of phase identification. • Thermal characteristics of glassy GeS{sub 2}. • The homogeneity range of AgGaGeS{sub 4} from the GeS{sub 2} side.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Qualification of a sublimation tool applied to the case of metalorganic chemical vapor deposition of In{sub 2}O{sub 3} from In(tmhd){sub 3} as a solid precursor

A solid delivery system consisting of a source canister, a gas management, and temperature controlled enclosure designed and manufactured by Air Liquide Electronics Systems was tested in the context of gas-phase delivery of the In(tmhd){sub 3} solid precursor. The precursor stream was delivered to a thermal metalorganic chemical vapor deposition reactor to quantify deposition yield under various conditions of carrier gas flow and sublimation temperature. The data collected allowed the determination of characteristic parameters such as the maximum precursor flow rate (18.2 mg min{sup −1} in specified conditions) and the critical mass (defined as the minimum amount of precursor able to attain the maximum flow rate) found to be about 2.4 g, as well as an understanding of the influence of powder distribution inside the canister. Furthermore, this qualification enabled the determination of optimal delivery conditions which allowed for stable and reproducible precursor flow rates over long deposition times (equivalent to more than 47 h of experiment). The resulting In{sub 2}O{sub 3} layers was compared with those elaborated via pulsed liquid injection obtained in the same chemical vapor deposition chamber and under the same deposition conditions.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Spin-injection optical pumping of molten cesium salt and its NMR diagnosis

Nuclear spin polarization of cesium ions in the salt was enhanced during optical pumping of cesium vapor at high magnetic field. Significant motional narrowing and frequency shift of NMR signals were observed by intense laser heating of the salt. When the hyperpolarized salt was cooled by blocking the heating laser, the signal width and frequency changed during cooling and presented the phase transition from liquid to solid. Hence, we find that the signal enhancement is mostly due to the molten salt and nuclear spin polarization is injected into the salt efficiently in the liquid phase. We also show that optical pumping similarly induces line narrowing in the solid phase. The use of powdered salt provided an increase in effective surface area and signal amplitude without glass wool in the glass cells.

36 MATERIALS SCIENCE↗

Optical emission diagnostics of plasmas in chemical vapor deposition of single-crystal diamond

A key aspect of single crystal diamond growth via microwave plasma chemical vapor deposition is in-process control of the local plasma–substrate environment, that is, plasma gas phase concentrations of activated species at the plasma boundary layer near the substrate surface. Emission spectra of the plasma relative to the diamond substrate inside the microwave plasma reactor chamber have been analyzed via optical emission spectroscopy. The spectra of radical species such as CH, C{sub 2}, and H (Balmer series) important for diamond growth were identified and analyzed. The emission intensities of these electronically excited species were found to be more dependent on operating pressure than on microwave power. Plasma gas temperatures were calculated from measurements of the C{sub 2} Swan band (d{sup 3}Π → a{sup 3}Π transition) system. The plasma gas temperature ranges from 2800 to 3400 K depending on the spatial location of the plasma ball, microwave power and operating pressure. Addition of Ar into CH{sub 4}+H{sub 2} plasma input gas mixture has little influence on the Hα, Hβ, and Hγ intensities and single-crystal diamond growth rates.

36 MATERIALS SCIENCE↗

Comparative study of three yttrium organometallic compounds for the stabilization of the cubic phase in YSZ deposited by PE-CVD

In this work, the efficiencies of three organometallic yttrium precursors used to produce YSZ coatings by plasma-enhanced chemical vapor deposition were studied. Yttrium (III) acetylacetonate, Y (acac) 3 , yttrium (III) hexafluoroacetylacetonate, Y (acacF 6 ) 3 , and yttrium (III) tris(2,2,6,6-tetramethyl-3,5-heptanedionate), Y (tmhd) 3 , were used to stabilize the cubic phase in zirconia deposited at temperatures from 500 to 800 °C. Our results showed that at temperatures between 500 and 600 °C, Y (tmhd) 3 appeared to be the most efficient dopant as it introduced the highest concentration of yttria (1–2.7 mol%) with only 6.4–5.6 at.% carbon. However, at 700 and 800 °C, Y (acac) 3 introduced twice as much yttria (8–15 mol%) as Y (tmhd) 3 with almost the same amount of carbon (5.4–3 at.%). Conversely, Y (acacF6)3 was the least efficient as it maintained a low concentration of yttria of around 0.7–1.8 mol% with 3.6–8.2 at.% carbon for all the deposition temperatures. Among these precursors, only Y (acac) 3 surpassed 8 mol% yttria and achieved a fully stabilized cubic phase at 800 °C, with the remaining samples stabilizing only the tetragonal phase. The tetragonal phase was stabilized due to the formation of crystallites of around 10 nm. The observed difference in the efficiency of the three precursors was correlated to important differences in their decomposition behavior as observed by mass spectrometry and thermogravimetry/differential scanning calorimetry.

36 MATERIALS SCIENCE↗

Robust Chiral Organization of Cellulose Nanocrystals in Capillary Confinement

Here we showed large area uniformly aligned chiral photonic bioderived films from a liquid crystal phase formed by a cellulose nanocrystal (CNC) suspension placed in a thin capillary. As a result of the spatial confinement of the drying process, the interface between coexisting isotropic and chiral phases aligns perpendicular to the long axis of the capillary. This orientation facilitates a fast homogeneous growth of chiral pseudolayers parallel to the interface. Overall, the formation of organized solids takes hours vs weeks in contrast to the slow and heterogeneous process of drying from the traditional dish-cast approach. The saturation of water vapor in one end of the capillary causes anisotropic drying and promotes unidirectional propagation of the anisotropic phase in large regions that results in chiral CNC solid films with a uniformly oriented layered morphology. Corresponding ordering processes were monitored in situ at a nanoscale, mesoscale, and microscopic scale with complementary scattering and microscopic techniques. The resulting films show high orientation order at a multilength scale over large regions and preserved chiral handedness causing a narrower optical reflectance band and uniform birefringence over macroscopic regions in contrast to traditional dish-cast CNC films and those assembled in a magnetic field and on porous substrates. Finally, these thin films with a controllable and well-identified uniform morphology, structural colors, and handedness open up interesting possibilities for broad applications in bioderived photonic nanomaterials.

36 MATERIALS SCIENCE↗