Search NASA⌕ Search

SEARCH · Search NASA

Results for “delta method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

Hypersonic aerodynamic characteristics of an all-body research aircraft configuration

An experimental investigation was conducted at Mach 6 to determine the hypersonic aerodynamic characteristics of an all-body, delta-planform, hypersonic research aircraft (HYFAC configuration). The aerodynamic characteristics were obtained at Reynolds numbers based on model length of 2.84 million and 10.5 million and over an angle-of-attack range from minus 4 deg to 20 deg. The experimental results show that the HYFAC configuration is longitudinally stable and can be trimmed over the range of test conditions. The configuration had a small degree of directional stability over the angle-of-attack range and positive effective dihedral at angles of attack greater than 2 deg. Addition of canards caused a decrease in longitudinal stability and an increase in directional stability. Oil-flow studies revealed extensive areas of separated and vortex flow on the fuselage lee surface. A limited comparison of wind-tunnel data with several hypersonic approximations indicated that, except for the directional stability, the tangent-cone method gave adequate agreement at control settings between 5 deg and minus 5 deg and positive lift coefficient. A limited comparison indicated that the HYFAC configuration had greater longitudinal stability than an elliptical-cross-section configuration, but a lower maximum lift-drag ratio.

Clark, L. E.↗

An analytical design procedure for the determination of effective leading edge extensions on thick delta wings

An analytical design procedure for leading edge extensions (LEE) was developed for thick delta wings. This LEE device is designed to be mounted to a wing along the pseudo-stagnation stream surface associated with the attached flow design lift coefficient of greater than zero. The intended purpose of this device is to improve the aerodynamic performance of high subsonic and low supersonic aircraft at incidences above that of attached flow design lift coefficient, by using a vortex system emanating along the leading edges of the device. The low pressure associated with these vortices would act on the LEE upper surface and the forward facing area at the wing leading edges, providing an additional lift and effective leading edge thrust recovery. The first application of this technique was to a thick, round edged, twisted and cambered wing of approximately triangular planform having a sweep of 58 deg and aspect ratio of 2.30. The panel aerodynamics and vortex lattice method with suction analogy computer codes were employed to determine the pseudo-stagnation stream surface and an optimized LEE planform shape.

Farhad Ghaffari↗

Production and evolution path of dileptons at energies accessible to the HADES detector

Dilepton production in intermediate energy nucleus-nucleus collisions as well as in elementary proton-proton reactions is analyzed within the ultrarelativistic quantum molecular dynamics transport model. For C+C collisions at 1A GeV and 2A GeV the resulting invariant mass spectra are compared to recent HADES data. We find that the experimental spectrum for C+C at 2A GeV is slightly overestimated by the theoretical calculations in the region around the vector meson peak but fairly described in the low mass region, where the data are satisfactorily saturated by the Dalitz decay of the {eta} meson and the {delta} resonance. At 1A GeV an underestimation of the experimental data is found, pointing that at lower energies the low-mass region is not fully saturated by standardly parametrized {delta} Dalitz decays alone. Furthermore, predictions for dilepton spectra for pp reactions at 1.25, 2.2, and 3.5 GeV and Ar+KCl reactions at 1.75A GeV are presented. The study is complemented by a detailed investigation of the role of absorption of the parent particles on the corresponding dilepton yields in the regime that has so far been probed by HADES.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Inner-valence photoionization of O({sup 1}D): Experimental evidence for the 2s{sup 2}2p{sup 4}({sup 1}D){yields}2s{sup 1}2p{sup 5}({sup 1}P) transition

Photoionization and autoionization of electronically excited atomic oxygen O({sup 1}D) are investigated in the energy range between 12 and 26 eV using tunable laser-produced plasma radiation in combination with time-of-flight mass spectrometry. A broad, asymmetric, and intense feature is observed that is peaking at 20.53{+-}0.05 eV. It is assigned to the 2s{sup 2}2p{sup 4}({sup 1}D){yields}2s{sup 1}2p{sup 5}({sup 1}P) transition, which subsequently autoionizes by a Coster-Kronig transition, as predicted by the previous theoretical work [K. L. Bell et al., J. Phys. B 22, 3197 (1989)]. Specifically, the energy of the unperturbed transition occurs at 20.35{+-}0.07 eV. Its shape is described by a Fano profile revealing a q parameter of 4.25{+-}0.8 and a width of {gamma}=2.2{+-}0.15 eV. Absolute photoionization cross section {sigma} is derived, yielding {sigma}=22.5{+-}2.3 Mb at the maximum of the resonance. In addition, weak contributions to the O({sup 1}D) yield from dissociative ionization originating from molecular singlet oxygen [O{sub 2}({sup 1}{delta}{sub g})] are identified as well. Possible applications of the 2s{sup 2}2p{sup 4}({sup 1}D){yields}2s{sup 1}2p{sup 5}({sup 1}P) transition as a state-selective and sensitive probe of excited oxygen in combination with photoionization mass spectrometry are briefly discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of Ti incorporation on the interfacial and optical properties of HfTiO thin films

Interfacial and optical properties of HfTiO films with different Ti concentration grown by radio frequency reactive magnetron sputtering have been investigated by x-ray photoelectron spectroscopy (XPS) and spectroscopy ellipsometry (SE). XPS spectra indicate that interfacial layer is formed unavoidably for Ti doped and undoped HfO{sub 2} thin films and the interfacial structure is stable for Ti doped films. The composition of interfacial layer is most likely silicate and SiO{sub x}. Meanwhile, SE results indicate that the band gap of HfTiO thin films decreases with the increase in Ti concentration. Further results show that the valence band offset ({Delta}E{sub v}) decreases from 2.32 to 1.91 eV while the conduction band offset ({Delta}E{sub c}) decreases from 2.05 eV to 0.99 with the increase in Ti content. The optical constants consist of refractive index and extinction coefficient have also been investigated to provide the valuable references to prepare and select the HfTiO thin films for future high-k gate dielectrics.

36 MATERIALS SCIENCE↗

Neutron Stars with Delta-Resonances in the Walecka and Zimanyi-Moszkowski Models

In the present work we have obtained the equation of state of the highly asymmetric dense stellar matter focusing on the delta resonance formation. We extended the nonlinear Walecka (NLW) and Zimanyi-Moszkowski (ZM) models to accommodate in the context of the relativistic mean field approximation the Rarita-Schwinger field for the spin 3/2 resonances. With the constructed stellar matter equations of state we solve numerically the TOV equation (Tolman-Oppenheimer-Volkoff) in order to determine the internal structure of neutron stars, and discuss the obtained masses versus radii diagram.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

NEAR-INFRARED PHOTOMETRIC PROPERTIES OF 130,000 QUASARS: AN SDSS-UKIDSS-MATCHED CATALOG

We present a catalog of over 130,000 quasar candidates with near-infrared (NIR) photometric properties, with an areal coverage of approximately 1200 deg{sup 2}. This is achieved by matching the Sloan Digital Sky Survey (SDSS) in the optical ugriz bands to the UKIRT Infrared Digital Sky Survey (UKIDSS) Large Area Survey (LAS) in the NIR YJHK bands. We match the {approx}1 million SDSS DR6 Photometric Quasar catalog to Data Release 3 of the UKIDSS LAS (ULAS) and produce a catalog with 130,827 objects with detections in one or more NIR bands, of which 74,351 objects have optical and K-band detections and 42,133 objects have the full nine-band photometry. The majority ({approx}85%) of the SDSS objects were not matched simply because these were not covered by the ULAS. The positional standard deviation of the SDSS Quasar to ULAS matches is {delta}{sub R.A.} = 0.''1370 and {delta}{sub decl.} = 0.''1314. We find an absolute systematic astrometric offset between the SDSS Quasar catalog and the UKIDSS LAS, of |R.A.{sub offset}| = 0.''025 and |decl.{sub offset}| = 0.''040; we suggest the nature of this offset to be due to the matching of catalog, rather than image, level data. Our matched catalog has a surface density of {approx}53 deg{sup -2} for K {<=} 18.27 objects; tests using our matched catalog, along with data from the UKIDSS Deep Extragalactic Survey, imply that our limiting magnitude is i {approx} 20.6. Color-redshift diagrams, for the optical and NIR, show a close agreement between our matched catalog and recent quasar color models at redshift z {approx}< 2.0, while at higher redshifts, the models generally appear to be bluer than the mean observed quasar colors. The gJK and giK color spaces are used to examine methods of differentiating between stars and (mid-redshift) quasars, the key to currently ongoing quasar surveys. Finally, we report on the NIR photometric properties of high, z > 4.6, and very high, z > 5.7, redshift previously discovered quasars.

79 ASTRONOMY AND ASTROPHYSICS↗

VERY WIDE BINARIES AND OTHER COMOVING STELLAR COMPANIONS: A BAYESIAN ANALYSIS OF THE HIPPARCOS CATALOGUE

We develop Bayesian statistical methods for discovering and assigning probabilities to non-random (e.g., physical) stellar companions. These companions are either presently bound or were previously bound. The probabilities depend on similarities in corrected proper motion parallel and perpendicular to the brighter component's motion, parallax, and the local phase-space density of field stars. Control experiments are conducted to understand the behavior of false positives. The technique is applied to the Hipparcos Catalogue within 100 pc. This is the first all-sky survey to locate escaped companions still drifting along with each other. In the <100 pc distance range, {approx}220 high probability companions with separations between 0.01 and 1 pc are found. The first evidence for a population ({approx}300) of companions separated by 1-8 pc is found. We find these previously unnoticed naked-eye companions (both with V < 6th mag): Capella and 50 Per, {delta} Vel and HIP 43797, Alioth ({epsilon} UMa), Megrez ({delta} UMa) and Alcor, {gamma} and {tau} Cen, {phi} Eri and {eta} Hor, 62 and 63 Cnc, {gamma} and {tau} Per, {zeta} and {delta} Hya, {beta}{sup 01}, {beta}{sup 02} and {beta}{sup 03} Tuc, N Vel and HIP 47479, HIP 98174 and HIP 97646, and s Eri and HIP 14913. High probability fainter companions (>6th mag) of primaries with V < 4 are found for: Fomalhaut ({alpha} PsA), {gamma} UMa, {alpha} Lib, Alvahet ({iota} Cephi), {delta} Ara, {beta} Ser, {iota} Peg, {beta} Pic, {kappa} Phe, and {gamma} Tuc.

79 ASTRONOMY AND ASTROPHYSICS↗

Near tip stress and strain fields for short elastic cracks

Recent experimental fatigue crack growth studies have concluded an apparent anomalous behavior of short cracks. To investigate the reasons for this unexpected behavior, the present paper focuses on identifying the crack length circumstances under which the requirements for a single parameter (K(sub I) or delta K(sub I) if cyclic loading is considered) characterization are violated. Furthermore, an additional quantity, the T stress, as introduced by Rice, and the related biaxiality ratio, B, are calculated for several crack lengths and two configurations, the single-edge-cracked and the centrally-cracked specimen. It is postulated that a two-parameter characterization by K and T (or B) is needed for the adequate description of the stress and strain field around a short crack. To further verify the validity of this postulate, the influence of the third term of the Williams series on the stress, strain and displacement fields around the crack tip and in particular on the B parameter is also examined. It is found that the biaxiality ratio would be more negative if the third term effects are included in both geometries. The study is conducted using the finite element method with linearly elastic material and isoparametric elements and axial (mode I) loading. Moreover, it is clearly shown that it is not proper to postulate the crack size limits for 'short crack' behavior as a normalized ratio with the specimen width, a/w; it should instead be stated as an absolute, or normalized with respect to a small characteristic dimension such as the grain size. Finally, implications regarding the prediction of cyclic (fatigue) growth of short cracks are discussed.

Soediono, A. H.↗

Theoretical and experimental study of twisted and cambered delta wings designed for a Mach number of 3.5

Data are provided for the evaluation of the aerodynamic performance of a series of twisted and cambered delta wings designed for a Mach number of 3.5. Systematic force and pressure data are also presented for comparison with theory. Force tests were made at Mach numbers of 2.3, 3.0, 3.5, 4.0, and 4.6. Design lift coefficients of 0.0 and 0.1 were employed on the 55 deg and 68 deg sweep wings, and design lift coefficients of 0.0, 0.05, and 0.1 were employed on the 76 deg sweep wings. Pressure tests were conducted on the 55 deg and 76 deg sweep flat wings and on the 0.1 design lift coefficient 76 deg sweep wing. The results indicate that for the sweep angles tested, an increase in the zero-lift pitching-moment coefficient is the primary benefit of twist and camber at a Mach number of 3.5. Comparison of the experimental results with results obtained from several lift theories indicates that the Carlson-Middleton linear theory method gave the best overall agreement. The pressure data indicate, however, that there is a cancellation of error at high angle of attack where the lower surface pressures are significantly underpredicted over the inboard region of the wing and where the upper and lower surface pressures are overpredicted over the outboard region of the wing.

Sorrells, R. B., III↗

Making almost commuting matrices commute

Suppose two Hermitian matrices A, B almost commute ({parallel}[A,B]{parallel} {<=} {delta}). Are they close to a commuting pair of Hermitian matrices, A', B', with {parallel}A-A'{parallel},{parallel}B-B'{parallel} {<=} {epsilon}? A theorem of H. Lin shows that this is uniformly true, in that for every {epsilon} > 0 there exists a {delta} > 0, independent of the size N of the matrices, for which almost commuting implies being close to a commuting pair. However, this theorem does not specifiy how {delta} depends on {epsilon}. We give uniform bounds relating {delta} and {epsilon}. The proof is constructive, giving an explicit algorithm to construct A' and B'. We provide tighter bounds in the case of block tridiagonal and tridiagnonal matrices. Within the context of quantum measurement, this implies an algorithm to construct a basis in which we can make a projective measurement that approximately measures two approximately commuting operators simultaneously. Finally, we comment briefly on the case of approximately measuring three or more approximately commuting operators using POVMs (positive operator-valued measures) instead of projective measurements.

99 GENERAL AND MISCELLANEOUS↗

TDCOSMO. XII. Improved Hubble constant measurement from lensing time delays using spatially resolved stellar kinematics of the lens galaxy

Strong-lensing time delays enable measurement of the Hubble constant ($H_{0}$) independently of other traditional methods. The main limitation to the precision of time-delay cosmography is mass-sheet degeneracy (MSD). Some of the previous TDCOSMO analyses broke the MSD by making standard assumptions about the mass density profile of the lens galaxy, reaching 2% precision from seven lenses. However, this approach could potentially bias the $H_0$ measurement or underestimate the errors. For this work, we broke the MSD for the first time using spatially resolved kinematics of the lens galaxy in RXJ1131$-$1231 obtained from the Keck Cosmic Web Imager spectroscopy, in combination with previously published time delay and lens models derived from Hubble Space Telescope imaging. This approach allowed us to robustly estimate $H_0$, effectively implementing a maximally flexible mass model. Following a blind analysis, we estimated the angular diameter distance to the lens galaxy $D_{\rm d} = 865_{-81}^{+85}$ Mpc and the time-delay distance $D_{\Delta t} = 2180_{-271}^{+472}$ Mpc, giving $H_0 = 77.1_{-7.1}^{+7.3}$ km s$^{-1}$ Mpc$^{-1}$ - for a flat $\Lambda$ cold dark matter cosmology. The error budget accounts for all uncertainties, including the MSD inherent to the lens mass profile and the line-of-sight effects, and those related to the mass-anisotropy degeneracy and projection effects. Our new measurement is in excellent agreement with those obtained in the past using standard simply parametrized mass profiles for this single system ($H_0 = 78.3^{+3.4}_{-3.3}$ km s$^{-1}$ Mpc$^{-1}$) and for seven lenses ($H_0 = 74.2_{-1.6}^{+1.6}$ km s$^{-1}$ Mpc$^{-1}$), or for seven lenses using single-aperture kinematics and the same maximally flexible models used by us ($H_0 = 73.3^{+5.8}_{-5.8}$ km s$^{-1}$ Mpc$^{-1}$). This agreement corroborates the methodology of time-delay cosmography.

79 ASTRONOMY AND ASTROPHYSICS↗

A study of electromagnetic characteristics of {sup 124,126,128,130,132,134,136}Ba isotopes performed in the framework of IBA

It was pointed out that the level scheme of the transitional nuclei {sup 124,126,128,130,132,134,136}Ba also can be studied by both characteristics (IBM-1 and IBM-2) of the interacting boson model and an adequate point of the model leading to E2 transitions is therefore confirmed. Most of the {delta}(E2/M1) ratios that are still not known so far are stated and the set of parameters used in these calculations is the best approximation that has been carried out so far. It has turned out that the interacting boson approximation is fairly reliable for the calculation of spectra in the entire set of {sup 124,126,128,130,132,134,136}Ba isotopes.

74 ATOMIC AND MOLECULAR PHYSICS↗

The fundamental structure function of oscillator noise models

Continuous-time models of oscillator phase noise x(t) usually have stationary nth differences, for some n. The covariance structure of such a model can be characterized in the time domain by the structure function: D sub n (t;gamma sub 1, gamma sub 2) = E delta (n) sub gamma sub 1 x(s+t) delta(n) sub gamma sub 2 x (s). Although formulas for the special case D sub 2 (0;gamma,gamma) (the Allan variance times 2 gamma(2)) exist for power-law spectral models, certain estimation problems require a more complete knowledge of (0). Exhibited is a much simpler function of one time variable, D(t), from which (0) can easily be obtained from the spectral density by uncomplicated integrations. Believing that D(t) is the simplest function of time that holds the same information as (0), D(t) is called the fundamental structure function. D(t) is computed for several power-law spectral models. Two examples are D(t) = K/t/(3) for random walk FM, D(t) = Kt(2) 1n/t/ for flicker FM. Then, to demonstrate its use, a BASIC program is given that computes means and variances of two Allan variance estimators, one of which incorporates a method of frequency drift estimation and removal.

Greenhall, C. A.↗

Carbon-Carbon Nozzle Extension Development in Support of In-Space and Upper-Stage Liquid Rocket Engines

Upper stage and in-space liquid rocket engines are optimized for performance through the use of high area ratio nozzles to fully expand combustion gases to low exit pressures, increasing exhaust velocities. Due to the large size of such nozzles, and the related engine performance requirements, carbon-carbon (C-C) composite nozzle extensions are being considered to reduce weight impacts. Currently, the state-of-the-art is represented by the metallic and foreign composite nozzle extensions limited to approximately 2000 degrees F. used on the Atlas V, Delta IV, Falcon 9, and Ariane 5 launch vehicles. NASA and industry partners are working towards advancing the domestic supply chain for C-C composite nozzle extensions. These development efforts are primarily being conducted through the NASA Small Business Innovation Research (SBIR) program in addition to other low level internal research efforts. This has allowed for the initial material development and characterization, subscale hardware fabrication, and completion of hot-fire testing in relevant environments. NASA and industry partners have designed, fabricated and hot-fire tested several subscale domestically produced C-C extensions to advance the material and coatings fabrication technology for use with a variety of liquid rocket and scramjet engines. Testing at NASA's Marshall Space Flight Center (MSFC) evaluated heritage and state-of-the-art C-C materials and coatings, demonstrating the initial capabilities of the high temperature materials and their fabrication methods. This paper discusses the initial material development, design and fabrication of the subscale carbon-carbon nozzle extensions, provides an overview of the test campaign, presents results of the hot fire testing, and discusses potential follow-on development work. The follow on work includes the fabrication of ultra-high temperature materials, larger C-C nozzle extensions, material characterization, sub-element testing and hot-fire testing at larger scale.

Gradl, Paul R.↗

SU-C-BRB-01: Development of Dynamic Gimbaled X-Ray Head Swing Irradiation Technique

Purpose: The Vero4DRT has a unique gimbaled x-ray head with rotating around orthogonal two axes. The purpose of this study was to develop a new irradiation technique using the dynamic gimbaled x-ray head swing function. Methods: The Vero4DRT has maximum field size of 150Χ150 mm2. The expanded irradiation field (expanded-field) for the longitudinal direction which is vertical to the MLC sliding direction, was created by the MLC motion and the gimbaled x-ray head rotation. The gimbaled x-ray head was rotated ± 35 mm, and the expanded-field size was set as 150Χ220 mm2. To irradiate uniform dose distribution, the diamond-shaped radiation field was created and continuously moved for the longitudinal direction. It was achieved by combination of opening and closing of the MLC and gimbal swing rotation. To evaluate dosimetric characteristic of the expanded-field, films inserted in water-equivalent phantoms at 100 mm depth were irradiated and the field size, penumbra, flatness and symmetry were analyzed.In addition, the expanded-field irradiation technique was applied to virtual wedge irradiation. Wedged beam was acquired with the delta–shaped radiation field. 150Χ 220 mm2 fields with 15, 30, 45, and 60 degree wedge were examined. The wedge angles were measured with irradiated film and compared with assumed wedge angles. Results: The field size, penumbra, flatness and symmetry of the expanded-field were 150.0 mm, 8.1–8.4 mm, 2.8% and −0.8% for the lateral direction and 220.1 mm, 6.3–6.4 mm, 3.2% and −0.4% for the longitudinal direction at 100 mm depth. The measured wedge angles were 15.1, 30.2, 45.2 and 60.2 degrees. The differences between assumed and measured angles were within 0.2 degrees. Conclusion: A new technique of the gimbal swing irradiation was developed. To extend applied targets, especially for whole breast irradiation, the expanded-field and virtual wedge irradiations would be effective.

60 APPLIED LIFE SCIENCES↗

Measurement of Off-Body Velocity, Pressure, and Temperature in an Unseeded Supersonic Air Vortex by Stimulated Raman Scattering

A noninvasive optical method is used to make time-averaged (30 sec) off-body measurements in a supersonic airflow. Seeding of tracer particles is not required. One spatial component of velocity, static pressure, and static temperature are measured with stimulated Raman scattering. The three flow parameters are determined simultaneously from a common sample volume (0.3 by 0.3 by 15 mm) using concurrent measurements of the forward and backward scattered line shapes of a N2 vibrational Raman transition. The capability of this technique is illustrated with laboratory and large-scale wind tunnel testing that demonstrate 5-10% measurement uncertainties. Because the spatial resolution of the present work was improved to 1.5 cm (compared to 20 cm in previous work), it was possible to demonstrate a modest one-dimensional profiling of cross-flow velocity, pressure, and translational temperature through the low-density core of a stream-wise vortex (delta-wing model at Mach 2.8 in NASA Langley's Unitary Plan Wind Tunnel).

Herring, Gregory C.↗

A Novel Framework for Quantifying past Methane Recycling by Sphagnum-Methanotroph Symbiosis Using Carbon and Hydrogen Isotope Ratios of Leaf Wax Biomarkers

The concentration of atmospheric methane is strongly linked to variations in Earth's climate. Currently, we can directly reconstruct the total atmospheric concentration of methane, but not individual terms of the methane cycle. Northern wetlands, dominated by Sphagnum, are an important contributor of atmospheric methane, and we seek to understand the methane cycle in these systems. We present a novel method for quantifying the proportion of carbon Sphagnum assimilates from its methanotrophic symbionts using stable isotope ratios of leaf-wax biomarkers. Carbon isotope ratios of Sphagnum compounds are determined by two competing influences, water content and the isotope ratio of source carbon. We disentangled these effects using a combined hydrogen and carbon isotope approach. We constrained Sphagnum water content using the contrast between the hydrogen isotope ratios of Sphagnum and vascular plant biomarkers. We then used Sphagnum water content to calculate the carbon isotope ratio of Sphagnum's carbon pool. Using a mass balance equation, we calculated the proportion of recycled methane contributed to the Sphagnum carbon pool, 'PRM.' We quantified PRM in peat monoliths from three microhabitats in the Mer Bleue peatland complex. Modern studies have shown that water table depth and vegetation have strong influences on the peatland methane cycle on instrumental time scales. With this new approach, delta C-13 of Sphagnum compounds are now a useful tool for investigating the relationships among hydrology, vegetation, and methanotrophy in Sphagnum peatlands over the time scales of entire peatland sediment records, vital to our understanding of the global carbon cycle through the Late Glacial and Holocene.

air pollution↗