Search NASA⌕ Search

SEARCH · Search NASA

Results for “quality control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

Factors affecting laser-trim stability of thick film resistors

Various factors affecting precision of trim and resistor stability were considered. The influence of machine operating parameters on resistor performance was examined and quantified through statistically designed experiments for a Q switched YAG laser system. Laser kerf quality was studied by scanning electron microscopy and related to kerf isolation resistance measurements. A relatively simple production oriented, quality control test is proposed for rapid determination of kerf electrical stability. In addition, the effect of cut design and extent of trim on precision and stability were discussed.

Cote, R. E.↗

Making aerospace technology work for the automotive industry, introduction

NASA derived technology already in use in the automotive industry include: (1) developments in electronics design, computer systems, and quality control methods for line testing of cars and trucks; (2) a combustion analysis computer program for automotive engine research and development; (3) an infrared scanner and television display for analyzing tire design and performance, and for studying the effects of heat on the service life of V-belts, shock mounts, brakes, and rubber bearings; (4) exhaust gas analyzers for trouble shooting and emissions certification; (5) a device for reducing noise from trucks; and (6) a low cost test vehicle for measuring highway skid resistance. Services offered by NASA to facilitate access to its technology are described.

Olson, W. T.↗

Flight service evaluation of an advanced composite empennage component on commercial transport aircraft. Phase 1: Engineering development

The empennage component selected for this program is the vertical fin box of the L-1011 aircraft. The box structure extends from the fuselage production joint to the tip rib and includes the front and rear spars. Various design options were evaluated to arrive at a configuration which would offer the highest potential for satisfying program objectives. The preferred configuration selected consists of a hat-stiffened cover with molded integrally stiffened spars, aluminum trussed composite ribs, and composite miniwich web ribs with integrally molded caps. Material screening tests were performed to select an advanced composite material system for the Advanced Composite Vertical Fin (ACFV) that would meet the program requirements from the standpoint of quality, reproducibility, and cost. Preliminary weight and cost analysis were made, targets established, and tracking plans developed. These include FAA certification, ancillary test program, quality control, and structural integrity control plans.

Ary, A.↗

Management: A continuing literature survey with indexes

This bibliography lists 782 reports, articles, and other documents introduced into the NASA scientific and technical information system in 1977. The citations, and abstracts when available, are reproduced exactly as they appeared originally in IAA and STAR, including the original accession numbers from the respective announcement journals. Topics cover the management of research and development contracts, production, logistics, personnel, safety, reliability and quality control citations. Includes references on: program, project and systems management; management policy, philosophy, tools, and techniques; decisionmaking processes for managers; technology assessment; management of urban problems; and information for managers on Federal resources, expenditures, financing, and budgeting.

Source record↗

Software engineering project management - A state-of-the-art report

The management of software engineering projects in the aerospace industry was investigated. The survey assessed such features as contract type, specification preparation techniques, software documentation required by customers, planning and cost-estimating, quality control, the use of advanced program practices, software tools and test procedures, the education levels of project managers, programmers and analysts, work assignment, automatic software monitoring capabilities, design and coding reviews, production times, success rates, and organizational structure of the projects.

Thayer, R. H.↗

Making aerospace technology work for the automotive industry - Introduction

In many cases it has been found that advances made in one technical field can contribute to other fields. An investigation is in this connection conducted concerning subjects from contemporary NASA programs and projects which might have relevance and potential usefulness to the automotive industry. Examples regarding aerospace developments which have been utilized by the automotive industry are related to electronic design, computer systems, quality control experience, a NASA combustion scanner and television display, exhaust gas analyzers, and a device for suppressing noise propagated through ducts. Projects undertaken by NASA's center for propulsion and power research are examined with respect to their value for the automotive industry. As a result of some of these projects, a gas turbine engine and a Stirling engine might each become a possible alternative to the conventional spark ignition engine.

Olson, W. T.↗

Design information for solar-heating systems

Report contains preliminary design information for two solar-heating and hot water systems presently under development. Information includes quality control data, special tooling specifications, hazard analysis, and preliminary training program for installation contractors.

Source record↗

Nondestructive pull tester

Quality control of welded electric wires is improved with easy-to-use tool applying small constant pull force to weldment (typically less than one-twentieth force required to pull weld apart).

Levy, A.↗

Rapid testing of pulse transformers

Quality-control testing of pulse transformers is speeded up by method for determining rise time and droop. Instead of using oscilloscope and square-wave generator to measure these characteristics directly, method uses voltmeter and sine-wave generator to measure them indirectly in about one-tenth time. Droop and rise time are determined by measuring input/output voltage ratio at just four frequencies.

Grillo, J.↗

Silicon solar cell process development, fabrication and analysis

A program plan, baseline process, measurement program and quality control plan were generated. Cutting operations were completed on the silicon sheet material. The first fabrication run of polycrystalline silicon into solar cells by baseline process was completed. Average conversion efficiency for solar cells fabricated by the baseline process from sheet and measured at air mass zero was 10.4%, compared with the control cells, fabricated from single crystal CZ silicon, whose average conversion efficiency was 12.2%.

Source record↗

Detecting surface faults on solar mirrors

Two quality control tests determine reflectivity and curvature faults of concave solar mirrors. Curvature defects in solar mirrors are easily revealed by photographing mirror surface. Calibrated aperture placed in front of camera lens admits rays reflecting only from acceptable areas of mirror, blocking out diverging rays reflected from defective areas. Defects can pinpoint problems that may exist in production. Same photograph can be obtained using calibrated disk instead of aperture, except that, this time, only defective areas would be exposed.

Argoud, M. J.↗

Tube-welder aids

Simple tools assist in setting up and welding tubes. Welder aids can be easily made to fit given tube diameter. Finished set can be used repeatedly to fix electrode-to-weld gap and mark sleeve and joint positions. Tools are readily made in tube-manufacturing plants and pay for themselves in short time in reduced labor costs and quality control: Conventional measurements are too slow for mass production and are prone to errors.

Weaver, J. F.↗

The scatter of mechanical values of carbon fiber composites and its causes

The scatter of experimental data obtained in an investigation of the parameters of structural components was investigated. Strength parameters which are determined by the resin or the adhesion between fiber and resin were included. The statistical characteristics of the mechanical parameters of carbon fiber composites, and the possibilities which exist to reduce this scatter were emphasized. It is found that quality control tests of fiber and resin are important for such a reduction.

Roth, S.↗

The use of wood for wind turbine blade construction

The interrelationships between moisture and wood, conditions for dry rot spore activity, the protection of wood fibers from moisture, wood resin composites, wood laminating, quality control, and the mechanical properties of wood are discussed. The laminated veneer and the bonded sawn stock fabrication techniques, used in the construction of a turbine blade with a monocoque 'D' section forming the leading edge and a built up trailing edge section, are described. A 20 foot root end sample complete with 24 bonded-in studs was successfully subjected to large onetime loads in both the flatwise and edgewise directions, and to fatigue tests. Results indicate that wood is both a viable and advantageous material for use in wind turbine blades. The basic material is reasonably priced, domestically available, ecologically sound, and easily fabricated with low energy consumption.

Gougeon, M.↗

Management. A continuing bibliography with indexes

This bibliography cites 604 reports, articles, and other documents introduced into the NASA scientific and technical information system in 1979 covering the management of research and development, contracts, production, logistics, personnel, safety, reliability and quality control. Program, project, and systems management; management policy, philosophy, tools, and techniques; decision making processes for managers; technology assessment; management of urban problems; and information for managers on Federal resources, expenditures, financing, and budgeting are also covered. Abstracts are provided as well as subject, personal author, and corporate source indexes.

Source record↗

Practical applications of surface analytic tools in tribology

A brief description of many of the widely used tools is presented. Of this list, those which have the highest applicability for giving elemental and/or compound analysis for problems of interest in tribology along with being truly surface sensitive (that is less than 10 atomic layers) are presented. The latter group is critiqued in detail in terms of strengths and weaknesses. Emphasis is placed on post facto analysis of experiments performed under real conditions (e.g., in air with lubricants). It is further indicated that such equipment could be used for screening and quality control.

Ferrante, J.↗

Development and demonstration of manufacturing processes for fabricating graphite/LARC-160 polyimide structural elements, part 4, paragraph B

A quality assurance program was developed which included specifications for celion/LARC-160 polyimide materials and quality control of materials and processes. The effects of monomers and/or polymer variables and prepeg variables on the processibility of celion/LARC prepeg were included. Processes for fabricating laminates, honeycomb core panels, and chopped fiber moldings were developed. Specimens and conduct tests were fabricated to qualify the processes for fabrication of demonstration components.

Source record↗

Approach to Sounding on the VAS Processor

The key features of the sounding software laboratory being installed on the VAS Processor at NASA/GSFC are outlined. Emphasis is on the support data and personal guidance that a meteorological researcher must provide to attune a physically modeled VAS sounding to his experiment. The fundamental aim of the sounding-support effort is to provide a system which makes use of: radiation transfer models based upon laboratory data, analytic inversion schemes, human guidance for quality control, statistically conditioned retrieval methods, and current ancillary data.

Chesters, D.↗