Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface backgrounds”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Search for a diffuse flux of photons with energies above tens of PeV at the Pierre Auger Observatory

Diffuse photons of energy above 0.1 PeV, produced through the interactions between cosmic rays and either interstellar matter or background radiation fields, are powerful tracers of the distribution of cosmic rays in the Galaxy. Furthermore, the measurement of a diffuse photon flux would be an important probe to test models of super-heavy dark matter decaying into gamma-rays. In this work, we search for a diffuse photon flux in the energy range between 50 PeV and 200 PeV using data from the Pierre Auger Observatory. For the first time, we combine the air-shower measurements from a 2 km 2 surface array consisting of 19 water-Cherenkov surface detectors, spaced at 433 m, with the muon measurements from an array of buried scintillators placed in the same area. Using 15 months of data, collected while the array was still under construction, we derive upper limits to the integral photon flux ranging from 13.3 to 13.8 km -2 sr -1 yr -1 above tens of PeV. We extend the Pierre Auger Observatory photon search program towards lower energies, covering more than three decades of cosmic-ray energy. This work lays the foundation for future diffuse photon searches: with the data from the next 10 years of operation of the Observatory, this limit is expected to improve by a factor of ∼20.

cosmic rays detectors↗
NASA NTRS1988

Kinetics of the reaction OH + HO2 yields H2O + O2 from 254 to 382 K

The discharge-flow resonance fluorescence technique has been used to determine the absolute rate constant for the reaction OH + HO2 yields H2O + O2 from 254 to 382 K at a total pressure of 1 Torr. Pseudo-=first-order conditions were used with HO2 in large excess over OH. The rate constant was obtained directly from observed decays of OH and measured concentrations of HO2. Since the observed rate constant was found to be very sensitive to small background concentrations of O and H atoms, NO2 was used to remove both atom species from the system. With added NO2 the result at 299 K is (1.1 + or - 0.3) x 10 to the -10th cu cm/molecule where the error limits are one standard deviation and include an estimate of overall experimental uncertainty. The temperature dependence expressed in Arrhenius form is (4.8 + or - 0.8) x 10 to the -11th exp (250 + or - 50)/T. The results are independent of the type of reactor surface and the precursor used to produce OH and HO2. The present results agree well with earlier measurements near 1-atm total pressure and suggest that this rate constant exhibits little or no pressure dependence between 1 and 1000 Torr.

Keyser, Leon F.↗
NASA NTRS2023

P-ACTIVE Project Report

The Phase change material-based actively-tunable filter (P-ACTIVE, Dr. Hyun Jung Kim, the Principal Investigator / PI) project is a NASA Langley Research Center (LaRC)-led research endeavor that began as a NASA CIF (Center Innovation Fund) project in 2019. The goal of P-ACTIVE is to develop all-solid-state tunable optical filters that can serve as low-Size, Weight, and Power (SWaP) replacements to the ubiquitous filter wheel technology current in use, and serve as a starting point for completely new optical component technologies. By using materials commonly used in electronic memory devices, namely chalcogenide phase-change materials (PCMs), in conjunction with nanostructured surfaces with exotic, tailored optical responses (“metasurfaces”), the P-ACTIVE filters are able to tune their optical transmission/reflection behavior in real-time. Because of this new functionality, P-ACTIVE filters are highlighted for NASA science and space programs such as next generation Lidar, landing system (SLS) thermal monitoring, thermal imaging, imaging spectroscopy, and disaster monitoring (e.g., volcanic eruption observations from SmallSats). This document intends to serve as a compendium of the P-ACTIVE project. We begin by describing the project from background science and assume no prior knowledge of the subject. We then address experimental and theoretical results of P-ACTIVE device performance, as well as recent results obtained from the MISSE-14 mission related to space qualification of P-ACTIVE devices and constituent materials. We conclude with a prospective view of the P-ACTIVE technology, and discuss the potential for these filters and other similar metasurface devices to serve NASA’s mission.

metamaterial↗
DOE OSTI2017

Reversible Self-Assembly of Glutathione-Coated Gold Nanoparticle Clusters via pH-Tunable Interactions

In this study, nanoparticle (NP) clusters with diameters ranging from 20 to 100 nm are reversibly assembled from 5 nm gold (Au) primary particles coated with glutathione (GSH) in aqueous solution as a function of pH in the range of 5.4 to 3.8. As the pH is lowered, the GSH surface ligands become partially zwitterionic and form interparticle hydrogen bonds that drive the self-limited assembly of metastable clusters in <1 min. Whereas clusters up to 20 nm in size are stable against cluster–cluster aggregation for up to 1 day, clusters up to 80 nm in size can be stabilized over this period via the addition of citrate to the solution in equal molarity with GSH molecules. The cluster diameter may be cycled reversibly by tuning pH to manipulate the colloidal interactions; however, modest background cluster–cluster aggregation occurs during cycling. Cluster sizes can be stabilized for at least 1 month via the addition of PEG-thiol as a grafted steric stabilizer, where PEG-grafted clusters dissociate back to starting primary NPs at pH 7 in fewer than 3 days. Whereas the presence of excess citrate has little effect on the initial size of the metastable clusters, it is necessary for both the cycling and dissociation to mediate the GSH–GSH hydrogen bonds. In conclusion, these metastable clusters exhibit significant characteristics of equilibrium self-limited assembly between primary particles and clusters on time scales where cluster–cluster aggregation is not present.

36 MATERIALS SCIENCE↗
NASA NTRS1991

Optimum combinations of visible and near-infrared reflectances for estimating the fraction of photosynthetically available radiation absorbed by plants

A useful parameter to estimate terrestrial primary productivity, that can be sensed from space, is the daily averaged fraction of Photosynthetically Available Radiation (PAR) absorbed by plants. To evaluate this parameter, investigators have relied on the fact that the relative amount of radiation reflected by a vegetated surface in the visible and near infrared depends on the fraction of the surface covered by the vegetation and therefore, correlates with absorbed PAR. They have used vegetation indices, namely normalized difference and simple ratio, to derive absorbed PAR. The problem with normalized difference and simple ratio is first, they are non linear functions of radiance or reflectance and therefore, cannot be readily applied to heterogeneous targets, second, they are used in generally nonlinear relationships, which make time integrals of the indices not proportional to primary productivity, and third, the relationships depend strongly on the type of canopy and background. To remove these limitations, linear combinations of visible and near infrared reflectances at optimum (one or two) viewing zenith angles are proposed.

Podaire, Alain↗
NASA NTRS2004

Passive Remote Sensing of Cloud Ice Particles

Hurricanes, blizzards and other weather events are important to understand not only for disaster preparation, but also to track the global energy balance and to improve weather and climate forecasts. For several decades, passive radiometers and active radars on aircraft and satellites have been employed to remotely sense rain rates and the properties of liquid particles. In the past few years the relationships between frozen particles and millimeter-wave observations have become understood well enough to estimate the properties of ice in clouds. A brief background of passive remote sensing of precipitation will be presented followed by a focused discussion of recent research at NASA Goddard Space Flight Center estimating the properties of frozen particles in clouds. The retrievals are for (1) ice that will eventually melt into rain, (2) for solid precipitation falling in northern climates, and (3) cirrus ice clouds. The electromagnetic absorption and scattering properties and differences of liquid rain versus frozen particles will be summarized for frequencies from 6 to 340+ GHz. Challenges of this work including surface emissivity variability, non-linear and under-constrained relationships, and frozen particle unknowns will be discussed. Retrieved cloud particle contents and size distributions for ice above the melting layer in hurricanes, retrieved snowfall rates for a blizzard, and cirrus ice estimates will be presented. Future directions of this work will also be described.

Skofronick-Jackson, Gail↗
NASA NTRS2012

The Outer Limits of Galaxy Clusters: Observations to the Virial Radius with Suzaku, XMM,and Chandra

The outskirts of galaxy clusters, near the virial radius, remain relatively unexplored territory and yet are vital to our understanding of cluster growth, structure, and mass. In this presentation, we show the first results from a program to constrain the sate of the outer intra-cluster medium (ICM) in a large sample of galaxy clusters, exploiting the strengths of three complementary X-ray observatories: Suzaku (low, stable background), XMM-Newton (high sensitivity),and Chandra (good spatial resolution). By carefully combining observations from the cluster core to beyond r200, we are able to identify and reduce systematic uncertainties that would impede our spatial and spectral analysis using a single telescope. Our sample comprises nine clusters at z is approximately 0.1-0.2 fully covered in azimuth to beyond r200, and our analysis indicates that the ICM is not in hydrostatic equilibrium in the cluster outskirts, where we see clear azimuthal variations in temperature and surface brightness. In one of the clusters, we are able to measure the diffuse X-ray emission well beyond r200, and we find that the entropy profile and the gas fraction are consistent with expectations from theory and numerical simulations. These results stand in contrast to recent studies which point to gas clumping in the outskirts; the extent to which differences of cluster environment or instrumental effects factor in this difference remains unclear. From a broader perspective, this project will produce a sizeable fiducial data set for detailed comparison with high-resolution numerical simulations.

Miller, Eric D.↗
NASA NTRS2012

Can Asian Dust Trigger Phytoplankton Blooms in the Oligotrophic Northern South China Sea?

Satellite data estimate a high dust deposition flux (approximately 18 g m(exp-2 a(exp-1) into the northern South China Sea (SCS). However, observational evidence concerning any biological response to dust fertilization is sparse. In this study, we combined long-term aerosol and chlorophyll-a (Chl-a) measurements from satellite sensors (MODIS and SeaWiFS) with a 16-year record of dust events from surface PM10 observations to investigate dust transport, flux, and the changes in Chl-a concentration over the northern SCS. Our result revealed that readily identifiable strong dust events over this region, although relatively rare (6 cases since 1994) and accounting for only a small proportion of the total dust deposition (approximately 0.28 g m(exp-2 a(exp-1), do occur and could significantly enhance phytoplankton blooms. Following such events, the Chl-a concentration increased up to 4-fold, and generally doubled the springtime background value (0.15 mg m(exp-3). We suggest these heavy dust events contain readily bioavailable iron and enhance the phytoplankton growth in the oligotrophic northern SCS.

northern South China sea↗
NASA NTRS2019

Cleanroom Contamination Identification Method Development

During fabrication, assembly, and testing of spacecraft and flight hardware it is vital to avoid contaminants that can cause degradation and could result in significant failure. Yet, there is no existing contamination monitoring method that provides the identity of airborne particles in a cleanroom facility. Knowing the particle identities, would allow scientists and engineers to determine the source of the contaminants and prevent setbacks before they occur or cause damage. Current cleanliness monitoring methods include airborne particle counters (APCs), fallout filters, and visual inspections. Particle counts from APCs are the primary metric used to define a cleanroom class and hence its level of cleanliness, but do not provide identification nor can they differentiate between large and small sizes of particles. In addition, using fallout filters is not a proactive, timely, or representative approach to cleanroom contamination monitoring because these samples are only retrieved after 30 days and are placed away from spacecraft processing to avoid interference with operations. In contrast, the forced air sampling method can collect a sample within an hour at any location required and provide results in less than a day. This system uses a cassette and filter sample medium to capture airborne particles which are then taken to a scanning electron microscope with energy dispersive spectroscopy (SEM/EDS) to identify and size the captured particles. Development of forced air sampling into an established laboratory capability will allow for fast sampling and routine identification of unknown contamination sources within the cleanroom. The test method development required market research for an air sampling cassette that increases sample collection efficiency and a filter with low enough background contamination to allow differentiation between a blank (control) and the collected sample. It was determined that a conductive black cassette and a polycarbonate filter were the best options. Conductive black cassettes, in comparison to the standard styrene, are manufactured using polypropylene filled with carbon. This makes the cassette conductive and minimizes the tendency of particles to stick to the wall of the cassette due to electrostatic force. In previous trials a mixed cellulose ester (MCE) filter was used to capture the contaminants, however the rougher surface of the filter contributed to entrapment of the particles within the filter structure and made it harder to identify the particles. In comparison, track etched polycarbonate filters have random cylindrical pores and a smooth surface which contributes to uniform sample distribution on the surface of the filter. Future work includes: testing the system using control samples to determine the efficiency and suitability of the medium, performing sample collection in various environments to establish ideal operating parameters and analyzing contaminant particles using SEM/EDS and assistant characterization techniques. Once fully developed, employing the forced air sampling method will help to prevent damage to spacecraft, avoid schedule delays, and allow for mission success.

Hernandez Melendez, Jailyn M.↗
NASA NTRS1983

A helium-3 refrigerator employing capillary confinement of liquid cryogen

A condensation refrigerator suitable for operation in a zero gravity space environment was constructed. The condensed liquid refrigerant is confined by surface tension inside a porous metal matrix. Helium-4 and helium-3 gases were condensed and held in a copper matrix. Evaporative cooling of confined liquid helium-4 resulted in a temperature of 1.4K. Using a zeolite adsorption pump external to the cryostat, a temperature of 0.6 K was achieved through evaporative cooling of liquid helium-3. The amount of time required for complete evaporation of a controlled mass of liquid helium-4 contained in the copper matrix was measured as a function of the applied background power. For heating powers below 18 mW the measured times are consistent with the normal boiling of the confined volume of liquid refrigerant. At background powers above 18 mW the rapid rise in the temperature of the copper matrix the signature of the absence of confined liquid occurs in a time a factor of two shorter than that expected on the basis of an extrapolation of the low power data.

Ennis, D. J.↗
NASA NTRS2005

Improved Anode for a Direct Methanol Fuel Cell

A modified chemical composition has been devised to improve the performance of the anode of a direct methanol fuel cell. The main feature of the modified composition is the incorporation of hydrous ruthenium oxide into the anode structure. This modification can reduce the internal electrical resistance of the cell and increase the degree of utilization of the anode catalyst. As a result, a higher anode current density can be sustained with a smaller amount of anode catalyst. These improvements can translate into a smaller fuel-cell system and higher efficiency of conversion. Some background information is helpful for understanding the benefit afforded by the addition of hydrous ruthenium oxide. The anode of a direct methanol fuel cell sustains the electro-oxidation of methanol to carbon dioxide in the reaction CH3OH + H2O--->CO2 + 6H(+) + 6e(-). An electrocatalyst is needed to enable this reaction to occur. The catalyst that offers the highest activity is an alloy of approximately equal numbers of atoms of the noble metals platinum and ruthenium. The anode is made of a composite material that includes high-surface-area Pt/Ru alloy particles and a proton-conducting ionomeric material. This composite is usually deposited onto a polymer-electrolyte (proton-conducting) membrane and onto an anode gas-diffusion/current-collector sheet that is subsequently bonded to the proton-conducting membrane by hot pressing. Heretofore, the areal density of noble-metal catalyst typically needed for high performance has been about 8 mg/cm2. However, not all of the catalyst has been utilized in the catalyzed electro-oxidation reaction. Increasing the degree of utilization of the catalyst would make it possible to improve the performance of the cell for a given catalyst loading and/or reduce the catalyst loading (thereby reducing the cost of the cell). The use of carbon and possibly other electronic conductors in the catalyst layer has been proposed for increasing the utilization of the catalyst by increasing electrical connectivity between catalyst particles. However, the relatively low density of carbon results in thick catalyst layers that impede the mass transport of methanol to the catalytic sites. Also, the electrical conductivity of carbon is less than 1/300th of typical metals. Furthermore, the polymer-electrolyte membrane material is acidic and most metals are not chemically stable in contact with it. Finally, a material that conducts electrons (but not protons) does not contribute to the needed transport of protons produced in the electro-oxidation reaction.

Valdez, Thomas↗
NASA NTRS2012

Analyzers Measure Greenhouse Gases, Airborne Pollutants

In complete darkness, a NASA observatory waits. When an eruption of boiling water billows from a nearby crack in the ground, the observatory s sensors seek particles in the fluid, measure shifts in carbon isotopes, and analyze samples for biological signatures. NASA has landed the observatory in this remote location, far removed from air and sunlight, to find life unlike any that scientists have ever seen. It might sound like a scene from a distant planet, but this NASA mission is actually exploring an ocean floor right here on Earth. NASA established a formal exobiology program in 1960, which expanded into the present-day Astrobiology Program. The program, which celebrated its 50th anniversary in 2010, not only explores the possibility of life elsewhere in the universe, but also examines how life begins and evolves, and what the future may hold for life on Earth and other planets. Answers to these questions may be found not only by launching rockets skyward, but by sending probes in the opposite direction. Research here on Earth can revise prevailing concepts of life and biochemistry and point to the possibilities for life on other planets, as was demonstrated in December 2010, when NASA researchers discovered microbes in Mono Lake in California that subsist and reproduce using arsenic, a toxic chemical. The Mono Lake discovery may be the first of many that could reveal possible models for extraterrestrial life. One primary area of interest for NASA astrobiologists lies with the hydrothermal vents on the ocean floor. These vents expel jets of water heated and enriched with chemicals from off-gassing magma below the Earth s crust. Also potentially within the vents: microbes that, like the Mono Lake microorganisms, defy the common characteristics of life on Earth. Basically all organisms on our planet generate energy through the Krebs Cycle, explains Mike Flynn, research scientist at NASA s Ames Research Center. This metabolic process breaks down sugars for energy to fuel cellular functions. "We think this chemical process did not exist when life first formed on Earth," he says, "because it is based on oxygen being available, and there was little oxygen available on the early Earth." It is possible that there are anaerobic regions beneath the sea floor in which life forms like those early non-Krebs Cycle microbes may yet exist. To detect and potentially collect samples of life emerging from hydrothermal vents, Flynn and his colleagues created Medusa, a multi-sensor instrument designed for long-term observation of diked vents on the ocean floor. When the vents erupt, Medusa assesses indicators of life within the expelled water. If the results are positive, the observatory collects samples and detaches from the ocean floor, making the long journey to the surface for retrieval by scientists. One of the indicators Medusa measures is the ratio of carbon isotopes in the water, namely carbon-12 and carbon-13. Living organisms preferentially take up carbon-12, Flynn says, so examining the ratio of these isotopes can help to determine the source of carbon in an environment as either biological or non-biological. "On Mars, there is evidence of localized methane in the atmosphere, and that methane could come from biological sources or from geochemical ones," Flynn says. "Determining the background planetary carbon isotope ratios and then evaluating the specific carbon ratios in this methane would help to determine how it was formed." A long-duration observatory similar to Medusa could one day provide essential evidence for or against the presence of life on the Red Planet or beneath the ice-crusted oceans of Europa.

Source record↗
DOE OSTI2022

Understanding Air-Sea Feedbacks to the MJO through Process Evaluation of Observations and Models (Final Report)

The goal of our project was to enhance our understanding of the role of coupling in the simulation of the Madden Julian Oscillation (MJO) in coupled climate models. We developed diagnostics of precipitation and Sea Surface Temperature variability in climate models and investigated how they are related to metrics of MJO simulation performance. We found a relationship between models with a high spatial coherence of precipitation and a good propagation of the MJO through the Maritime Continent region, but no relationship between metrics of precipitation organisation and intensity. Analysis of coupled and uncoupled model simulations from the Sixth Coupled Model Intercomparison Project (CMIP6) shows that coupling systematically improved the MJO simulation in both metrics that we investigated. We analysed the role of background moisture gradients in the MJO simulation performance following Lim et al. (2018) and found that although the model to model variation in moisture gradients to the west of Indonesia was related to model MJO performance, in general no single moisture gradient was as good at explaining a large fraction of MJO performance across the models as compared to a linear combination of those metrics, which was able to explain a significant fraction of the variance in the MJO performance. Those relationships were much stronger for coupled simulations than uncoupled simulations and stronger for those metrics that measured propagation of the MJO across the Maritime Continent than for overall MJO activity.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Survey of the mechanical and physical behaviors of yttria-stabilized zirconia from multiple dental laboratories

Background: When selecting zirconia for a dental restoration, laboratory prescriptions often refer to high strength and high translucency. In this survey, zirconia specimens were ordered from various dental laboratories for posterior (high strength) and anterior (high translucency) clinical indications. The specimens were then tested and evaluated for their mechanical and physical behaviors. Methods: In a double-blinded manner, 9 laboratories provided 32 specimens from 17 different zirconia blanks, which were tested in the American Dental Association laboratory. Flexural strength tests were performed on standard specimens, and fracture surfaces were examined using both optical and scanning electron microscopy. Chemical composition, Vickers hardness, and absolute transmittance measurements were also performed. Results: A large scatter in the strength values was observed. The zirconia intended for posterior applications displayed strengths (SD) from 195 through 783 MPa (490 [183] MPa), which overlapped greatly with the strengths (SD) of the zirconia intended for anterior applications, 320 through 768 MPa (581 [136] MPa). However, when the strength values were recalculated on the basis of yttria content, the strengths (SD) were 584 (158) MPa for 3 mol% yttria and 373 (104) MPa for 5 mol% yttria. Conclusions: When a prescription was given to dental laboratories to request zirconia on the basis of clinical requirements, there was a large scatter and no consistency in the resulting strength values partly because of mixed use of 3 mol% and 5 mol% yttria zirconia. The 3 mol% materials had much higher strength when the strength values were grouped according to yttria content. Strength was also highly dependent on processing and finishing at the dental laboratories.

3 mol% yttria-tetragonal zirconia polycrystal (3Y-↗
NASA NTRS1981

IUE spectra of F and late A stars

The International Ultraviolet Explorer (IUE) spectra of alpha CMi (F5 IV-V), beta Cas (F2 IV), alpha Car (F0 Ib), and gamma Boo (A7 III) in the context of the question as to whether chromospheres disappear in the early F late A portions of the Hertzsprung-Russell diagram. Both alpha CMi (Procyon) and beta Cas show bright emission line spectra indicative of chromospheres and transition regions, but neither alpha Car (Canopus) nor gamma Boo show any evidence of emission in their SWP spectra or at the Mg II lines, despite very deep exposures. Alpha CMi has emission line fluxes roughly 6 times those of the quiet Sun, but the rapidly rotating delta Scuti type variable beta Cas has surface fluxes 10 to 50 times those of the quiet Sun. Upper limits on emission line fluxes for alpha Car are 4 to 20 and for gamma Boo 15 to 80 times the quiet Sun. It is concluded that the apparent absence of emission lines in the spectra of alpha Car and gamma Boo should not be interpreted as due to the absence of nonradiatively heated outer atmospheres in stars hotter than spectral type F0, but rather to the inability to see emission lines with IUE against a background of scattered light and a bright photospheric absorption line spectrum either in low or high dispersion.

Linsky, J. L.↗
NASA NTRS1990

Optical constants of solid methane

Methane is the most abundant simple organic molecule in the outer solar system bodies. In addition to being a gaseous constituent of the atmospheres of the Jovian planets and Titan, it is present in the solid form as a constituent of icy surfaces such as those of Triton and Pluto, and as cloud condensate in the atmospheres of Titan, Uranus, and Neptune. It is expected in the liquid form as a constituent of the ocean of Titan. Cometary ices also contain solid methane. The optical constants for both solid and liquid phases of CH4 for a wide temperature range are needed for radiative transfer calculations, for studies of reflection from surfaces, and for modeling of emission in the far infrared and microwave regions. The astronomically important visual to near infrared measurements of solid methane optical constants are conspicuously absent from the literature. Preliminary results are presented on the optical constants of solid methane for the 0.4 to 2.6 micrometer region. Deposition onto a substrate at 10 K produces glassy (semi-amorphous) material. Annealing this material at approximately 33 K for approximately 1 hour results in a crystalline material as seen by sharper, more structured bands and negligible background extinction due to scattering. The constant k is reported for both the amorphous and the crystalline (annealed) states. Typical values (at absorption maxima) are in the .001 to .0001 range. Below lambda = 1.1 micrometers the bands are too weak to be detected by transmission through the films less than or equal to 215 micrometers in thickness, employed in the studies to date. Using previously measured values of the real part of the refractive index, n, of liquid methane at 110 K, n is computed for solid methane using the Lorentz-Lorenz relationship. Work is in progress to extend the measurements of optical constants n and k for liquid and solid to both shorter and longer wavelengths, eventually providing a complete optical constants database for condensed CH4.

Khare, Bishun N.↗
NASA NTRS1992

An examination of the assumptions in the POLCAL cross-talk removal algorithm

The POLCAL crosstalk removal algorithm is based on the statistical properties of the image background and does not need any corner reflector or active radar calibrator deployed in the scene. The advantage of being able to remove the crosstalk contamination without using external calibration targets gives rise to the consideration of algorithms based on clutter statistics in polarimetric synthetic aperture radar (SAR) images in more detail. The basic assumption of the POLCAL procedure is the decorrelation of copolarized and cross-polarized backscatter, which is valid for natural targets with azimuthal symmetry. This assumption and others regarding the properties of the imaged surface are examined. An improved version called POLCALII is presented, and its performance is compared with POLCAL.

Zink, M.↗
NASA NTRS1996

Wideband Interferometric Sensing and Imaging Polarimetry

Wideband Interferometric Sensing and Imaging Polarimetry (WISIP) has become an important, indispensible tool in wide area military surveillance and global environmental monitoring of the terrestrial and planetary covers. It enables dynamic, real time optimal feature extraction of significant characteristics of desirable targets and/or target sections with simultaneous suppression of undesirable background clutter and propagation path speckle at hitherto unknown clarity and never before achieved quality. WISIP may be adopted to the detection, recognition, and identification (DRI) of any stationary, moving or vibrating targets or distributed scatterer segments versus arbitrary stationary, dynamical changing and/or moving geo-physical/ecological environments, provided the instantaneous 2x2 phasor and 4x4 power density matrices for forward propagation/backward scattering, respectively, can be measured with sufficient accuracy. For example, the DRI of stealthy, dynamically moving inhomogeneous volumetric scatter environments such as precipitation scatter, the ocean/sea/lake surface boundary layers, the littoral coastal surf zones, pack ice and snow or vegetative canopies, dry sands and soils, etc. can now be successfully realized. A comprehensive overview is presented on how these modern high resolution/precision, complete polarimetric co-registered signature sensing and imaging techniques, complemented by full integration of novel navigational electronic tools, such as DGPS, will advance electromagnetic vector wave sensing and imaging towards the limits of physical realization. Various examples utilizing the most recent image data take sets of airborne, space shuttle, and satellite imaging systems demonstrate the utility of WISIP.

Verdi, James Salvatore↗