Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

Electroluminescence from n-ZnO microdisks/p-GaN heterostructure

The light emitting diode structure based on p-GaN film/n-ZnO microdisks quasiarray heterojunction was fabricated. It is shown that the epitaxial quality of p-GaN films upon growth from the vapor phase can lead to growth of the hexagonal microdisk ZnO rather than the vertical nanorods. The density of the microdisks changed across the substrate surface. ZnO hexagonal microdisks are characterized by the average height of about 5 μm with diameters ranging from 25 μm up to 60 μm. The turn-on voltage of the heterojunction of ZnO/GaN (disks/film) is around 5 V. The diode-ideality factor was estimated to be of around 30. The large values of the ideality factors indicate a high density of trap states and also may be connected with the quality of the contacts to the p–n junction. The electroluminescence (EL) spectrum acquired from the p-GaN film/n-ZnO microdisks junction exhibited the bands with maxima at 366, 394 and 495 nm. On the basis of the data of X-ray diffraction, electrical and optical studies these peaks were associated with GaN near-band-edge (NBE) emission, ZnO NBE emission, and emission from the defect levels in ZnO, respectively.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Investigation of Pt and Pd Modified WO{sub 3} and ZnO Based Thin Film Sensors for Ethanol Sensing

Ethanol sensors based on different WO{sub 3} and ZnO structures are studied in the present work. The XRD and SEM processes are used to characterize the sensing layer’s surface morphology which reveals the presence of nanoparticle in sensing layer. Further reducing the nanoparticle diameter by the addition of palladium (Pd) and platinum (Pt) for both the sensors (ZnO and WO{sub 3}) gives good results on sensitivity, operating temperature, response time and recovery time. Nanoparticle diameter for undoped WO{sub 3}, Pd-modified WO{sub 3} and Pt-modified WO{sub 3} based sensors is 11.8, 6 and 5.4 nm, whereas nanoparticle diameter for undoped, Pd-modified and Pt-modified ZnO based sensors is 20, 14 and 11 nm, respectively. Analysis of dynamic response of the sensors when exposed to different concentrations of ethanol vapour (from 500 to 10,000 ppm) and various temperatures indicate the improvement in sensitivity up to 77.2% for WO{sub 3} and 74.6% for ZnO based sensors.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

The Effect of Different Annealing Conditions on the Anisotropy of the Fracture Toughness of Ti-6Al-4V

The room-temperature tensile and fracture toughness properties of Ti-6Al-4V plate were tested to characterize the effect of rolling direction on the fracture toughness in two different heat treatment conditions. Optical and scanning electron microscopy was used to characterize the microstructure and fracture surfaces. It was found that beta annealing increased the fracture toughness compared to a mill annealed product in all three orientations relative to the rolling direction; however, it had minimal effects on strength and modulus. Ti-6Al-4V was found to be isotropic in fracture toughness, varying 0.48% in the beta annealed condition and 6.4% in the mill annealed condition.

36 MATERIALS SCIENCE↗

Microscale Observation via High-Speed X-ray Diffraction of Alloy 718 During In Situ Laser Melting

The laser melting process is accompanied by rapid evolution in temperature, phase, structure, and strain because of its high heating and cooling rates. In this study, the evolution of grains within a thin solid plate of Ni alloy 718 during laser processing was probed with in situ high-energy x-ray diffraction experiments. The high temporal and spatial resolution available in the measurement allowed us to study the rapid evolution of the melted region beneath the surface of the sample. The characterization of the evolution of secondary phases, i.e., Laves and carbide, was captured despite the weak diffracted peaks caused by small volume fractions. Thermal history was estimated based on changes in the lattice spacing from the thermal contraction upon cooling. In conclusion, the temporal variation in 2θ with azimuthal direction revealed the evolution in anisotropy of lattice spacing and thus of the mechanical state during laser processing.

36 MATERIALS SCIENCE↗

Be Surface Structures on W(110) and W(211): A DFT Study

Beryllium and Tungsten are promising candidates for use as plasma facing materials (PFMs) in upcoming fusion reactors. Many complex and competing phenomena however complicate the understanding and development of materials that operate in the harsh conditions of the reactor. In particular, redeposition of Be onto the W divertor must be considered due to the expected erosion of the Be first wall under exposure to the plasma. It is known that a build up of Be on W allows for the formation of BeW alloys which can harm the longevity and performance of the fusion divertor. In an effort to understand the interaction of Be with W surfaces, a study of Be structures on W(110) and W(211) as a function of Be coverage has been carried out using Density Functional Theory. We have found that both W surfaces develop monolayers of Be characterized by a densely packed hexagonal structure. Below this monolayer coverage, Be structures are found to have two motifs of coverage, a densely packed hexagonal pattern punctuated by areas of low-density coverage. The structures found here produce work function values and trends in good agreement with experimental measurements.

36 MATERIALS SCIENCE↗

Atomic structure and grain shape evolution of nanodiamond during annealing in oxidizing atmosphere from neutron diffraction and MD simulations

In this work, real space pair-distribution function (PDF) analysis in conjunction with molecular dynamics (MD) simulations was applied to characterize crystal structure, shape and surface structure of diamond nanoparticles annealed in air up to 880 °C. MD simulated models of individual nanodiamond particles of various shapes and sizes were used to calculate theoretical radial distribution functions G(r) for powders with different grain size distributions. The calculated curves, showing distinct differences for the explored parameter space, were compared to the experimental G(r) functions obtained from neutron scattering for annealed detonated nanodiamond samples in a search for a model best describing the actual powders. It was found that as-synthesized nanodiamond grains are terminated by equally abundant (100), (110) and (111) crystallographic faces and their structure does not change upon annealing in air up to 280 °C. The shape and size of grains annealed above 480 °C changes due to surface etching. The etching rate differs between crystals faces and depends on temperature, resulting in the observed differences in grain shape. Below 680 °C the share of the (110) facets gradually increases and at 680 °C the grains become rhombic dodecahedra terminated solely by (110) surfaces. Further increase of the annealing temperature promotes formation of (111) surfaces and at 880 °C the preferred grain shape becomes an octahedron terminated by a variant of (111) surfaces possessing three dangling sp3 bonds per atom. At lower temperatures all grains become smaller and the size distribution moves towards the lower values. Furthermore, as the annealing temperature increases, the smallest grains disappear entirely and the average grain size grows back.

36 MATERIALS SCIENCE↗

PdAgAu alloy with high resistance to corrosion by H 2 S

PdAgAu alloy films were prepared on porous stainless steel supports by sequential electroless deposition. Two specific compositions, Pd 83 Ag 2 Au 15 and Pd 74 Ag 14 Au 12 , were studied for their sulfur tolerance. The alloys and a reference Pd foil were exposed to 1000 H 2 S /H 2 at 623 K for periods of 3 and 30 hours. The microstructure, morphology and bulk composition of both nonexposed and H 2 S-exposed samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). XRD and SEM analysis revealed time-dependent growth of a bulk Pd{sub 4}S phase on the Pd foil during H 2 S exposure. In contrast, the PdAgAu ternary alloys displayed the same FCC structure before and after H 2 S exposure. In agreement with the XRD and SEM results, sulfur was not detected in the bulk of either ternary alloy samples by EDS, even after 30 hours of H 2 S exposure. X-ray photoelectron spectroscopy (XPS) depth profiles were acquired for both PdAgAu alloys after 3 and 30 hours of exposure to characterize sulfur contamination near their surfaces. Very low S 2p and S 2s XPS signals were observed at the top-surfaces of the PdAgAu alloys, and those signals disappeared before the etch depth reached ~ 10 nm, even for samples exposed to H 2 S for 30 hours. The depth profile analyses also revealed silver and gold segregation to the surface of the alloys; preferential location of Au on the alloys surface may be related to their resistance to bulk sulfide formation. In preliminary tests, a PdAgAu alloy membrane displayed higher initial H{sub 2} permeability than a similarly prepared pure Pd sample and, consistent with resistance to bulk sulfide formation, lower permeability loss in H 2 S than pure Pd.

36 MATERIALS SCIENCE↗

Growth of lattice-matched GaInAsP grown on vicinal GaAs(001) substrates within the miscibility gap for solar cells

The growth of quaternary Ga 0.68 In 0.32 As 0.35 P 0.65 by metal-organic vapor phase epitaxy is very sensitive to growth conditions because the composition is within a miscibility gap. In this investigation, we fabricated 1 um-thick lattice-matched GaInAsP films grown on GaAs(001) for application to solar cells. In order to characterize the effect of the surface diffusion of adatoms on the material quality of alloys, the growth temperature and substrate miscut are varied. Transmission electron microscopy and two-dimensional in-situ multi-beam optical stress determine that growth temperatures of 650 degrees C and below enhance the formation of the CuPtB atomic ordering and suppress material decomposition, which is found to occur at the growth surface. The root-mean-square (RMS) roughness is reduced from 33.6 nm for 750 degrees C to 1.62 nm for 650 degrees C, determined by atomic force microscopy. Our initial investigations show that the RMS roughness can be further reduced using increased miscut angle, and substrates miscut toward (111)A, leading to an RMS roughness of 0.56 nm for the sample grown at 600 degrees C on GaAs miscut 6 degrees toward (111)A. Using these conditions, we fabricate an inverted hetero-junction 1.62 eV Ga 0.68 In 0.32 As 0.35 P 0.65 solar cell without an anti-reflection coating with a short-circuit current density, open-circuit voltage, fill factor, and efficiency of 12.23 mA/cm2, 1.12 V, 86.18%, and 11.80%, respectively.

14 SOLAR ENERGY↗

Origin of deactivation of aqueous Na–CO 2 battery and mitigation for long-duration energy storage

Here, the development of long-duration energy storage technology is crucial to facilitate the efficient utilization of renewable energy sources while mitigating carbon dioxide production. In this study, we investigate the deactivation and reactivation mechanisms of the aqueous Na–CO 2 battery during extended cycling. We have designed the cathode to include non-precious intermetallic catalysts. As the cell undergoes repeated cycles, the voltage polarization during discharge progressively rises, eventually leading to the cell's deactivation and formation of decomposition products clogging the electrode surface. Results obtained from comprehensive characterization techniques, including conductive atomic force microscopy (cAFM), Raman spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction, and inductively coupled plasma-mass spectrometry provide insight into the decomposition products. We also showcase an electrochemical approach for regeneration of these aqueous cells. Our findings, along with the insights we have gained, provide a path toward creating long-duration systems with self-healing properties.

25 ENERGY STORAGE↗

A comparative study of physico-chemical properties of CBD and SILAR grown ZnO thin films

Graphical abstract: Schematic model indicating ZnO nanorods by CBD (Z{sub 1}) and nanograins by SILAR (Z{sub 2}). - Highlights: • Simple methods for the synthesis of ZnO thin films. • Comparative study of physico-chemical properties of ZnO thin films prepared by CBD and SILAR methods. • CBD outperforms SILAR method. - Abstract: In the present work, nanocrystalline zinc oxide (ZnO) thin films have been successfully deposited onto glass substrates by simple and economical chemical bath deposition (CBD) and successive ionic layer adsorption reaction (SILAR) methods. These films were further characterized for their structural, optical, surface morphological and wettability properties. The X-ray diffraction (XRD) patterns for both CBD and SILAR deposited ZnO thin films reveal the highly crystalline hexagonal wurtzite structure. From optical studies, band gaps obtained are 2.9 and 3.0 eV for CBD and SILAR deposited thin films, respectively. The scanning electron microscope (SEM) patterns show growth of well defined randomly oriented nanorods and nanograins on the CBD and SILAR deposited samples, respectively. The resistivity of CBD deposited films (10{sup 2} Ω cm) is lower than that of SILAR deposited films (10{sup 5} Ω cm). Surface wettability studies show hydrophobic nature for both films. From the above results it can be concluded that CBD grown ZnO thin films show better properties as compared to SILAR method.

36 MATERIALS SCIENCE↗

Molecular Characterization of Organic Aerosols Using Nanospray Desorption/Electrospray Ionization-Mass Spectrometry

Nanospray desorption electrospray ionization (Nano-DESI) combined with high-resolution mass spectrometry (HR/MS) is a promising approach for detailed chemical characterization of atmospheric organic aerosol (OA) collected in laboratory and field experiments. In Nano-DESI analyte is desorbed into a solvent bridge formed between two capillaries and the analysis surface, which enables fast and efficient characterization of OA collected on substrates without special sample preparation. Stable signals achieved using Nano-DESI make it possible to obtain high-quality HR/MS data using only a small amount of material (<10 ng). Furthermore, Nano-DESI enables efficient detection of chemically labile compounds in OA, which is important for understanding chemical aging phenomena.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Investigation of the Cathode–Catalyst–Electrolyte Interface in Aprotic Li–O 2 Batteries

Enabled by a unique integrated fabrication and characterization platform, X-ray photoelectron spectroscopy (XPS) studies reveal the formation of a thin solid electrolyte interphase (SEI) layer on a Li–O2 cathode after the first cycle. Subsequent cycling indicates that this SEI layer is very stable in terms of both chemistry and morphology, even after extensive cycling, preserving reversibility at the cathode/electrolyte interface. Remarkably, even after cell failure, replacement of the lithium anode resulted in recovery of the cycling behavior with the same cathode. These results demonstrate that chemical stabilization of the cathode/electrolyte interface promotes long-term operation of DMSO-based Li–O2 Ru-catalyzed batteries. Characterization of the Li anode surface reveals electrolyte decomposition, and a partial mechanism is proposed for the observed chemical composition of the cathode SEI. These studies are enabled by conformal deposition of a heterogeneous OER catalyst on a freestanding, binder-free, mesoporous, carbon-based Li–O2 cathode with high capacity and long-term cycling stability.

25 ENERGY STORAGE↗

Molecular-Level Structure and Packing in Phase-Separated Arachidic Acid–Perfluorotetradecanoic Acid Monolayer Films

Synchrotron-based X-ray scattering measurements of phase-separated surfactant monolayers at the air–water interface provide molecular-level structural information about the packing and ordering of film components. In this work, grazing incidence X-ray diffraction (GIXD) and X-ray reflectivity (XR) measurements were used to collect crystallographic structural information for binary mixed monolayers of arachidic acid (AA, C 19 H 39 COOH) with perfluorotetradecanoic acid (PA, C 13 F 27 COOH), a system that has previously been investigated using a variety of thermodynamic and micron-scale structural characterization methods. GIXD measurements at surface pressures of π = 5, 15, and 30 mN/m indicated that AA in pure and mixed films forms a rectangular lattice at π = 5 and 15 mN/m but a hexagonal lattice at π = 30 mN/m. PA formed hexagonal lattices under all conditions, with films being highly ordered and crystalline (as determined by Bragg peak width) at even the lowest surface pressures investigated. Phase separation occurred for all mixed monolayer film compositions and surface pressures, manifesting as diffraction peaks characteristic of the individual components appearing at different in-plane scattering vector q xy . For both pure and mixed films, the molecular tilt angle of the AA hydrocarbon chain toward the nearest-neighbor was substantial at low pressures but decreased with increasing pressure. The PA fluorocarbon chain showed negligible molecular tilt under all conditions, and was oriented normal to the subphase surface regardless of surface pressure or the presence of AA in the films. In all cases, the two components in the mixed film behaved entirely independently of film composition, which is exactly the expected result for a fully phase-separated, immiscible system. XR measurements of film thickness at the air–water interface supported these results; overall film thickness approached the calculated ideal surfactant tail lengths with increasing surface pressure, indicating nearly normal oriented surfactants. Furthermore, the overall surfactant packing and crystallographic features of the mixed monolayers are discussed in terms of the lipophobic nature of the perfluorinated surfactant as well as in context of thermodynamic miscibility and domain structure formation reported elsewhere in the literature for these mixed monolayer systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ionic-Based Electrochemical Gas Sensors for Low-Cost, High-Sensitivity SO2 Detection

Sulfur dioxide (SO2) is a toxic gas associated with adverse health and environmental effects that necessitate reliable monitoring techniques. Here, we report the development of an all-solid-state electrochemical sensor utilizing a lithium borate (Li3BO3) solid electrolyte capable of subppm of SO2 detection. While subppm of SO2 sensing has been previously demonstrated in other solid-state electrolyte systems─such as stabilized zirconia, natrium super ionic conductors (NASICON) under mixed-potential conditions─here we establish Li3BO3 as an alternative solid electrolyte enabling equilibrium potentiometric sensing in an all-solid architecture. This sensor demonstrates a detection limit of at least 0.25 ppm, surpassing the human-olfactory threshold and meeting the rigorous requirements for industrial and personal monitoring applications. The sensing mechanism relies on the formation of Li2SO4 on the electrode surface, as evidenced by multimodal characterization techniques, including Raman spectroscopy, scanning electron microscopy (SEM), and scanning transmission electron microscopy (STEM). The strong linear correlation between the open-circuit potential (OCV) and the logarithm of SO2 concentration between 0.25 and 2 ppm indicates that the response is Nernstian in nature.

Lagunas, Francisco (ORCID:000000026377683X)↗

Operando Depth-Resolved Measurement of Solvation Entropy, Interfacial Transport, and Charge-Transfer Kinetics in Lithium-Ion Batteries

Understanding and improving the performance and longevity of lithium-ion batteries critically depends on insight into the dynamic processes occurring at buried electrode-electrolyte interfaces. However, direct, depth-resolved, and operando diagnosis of these interfaces remains a longstanding challenge due to their inaccessibility beneath bulk materials, the limitations of conventional surface- and bulk-sensitive characterization tools, and the difficulty of maintaining realistic cell environments during measurement. These challenges have made it nearly impossible to uniquely resolve important interfacial properties such as charge transfer resistance, SEI (solid electrolyte interphase) resistance, and solvation entropy at the individual electrode interfaces within a working cell, information that is essential for mechanistic insight and accelerated battery design. Here, in this study, we report the development of multiharmonic electro-thermal spectroscopy (METS), an operando technique that enables depth-resolved measurement of solvation entropy, interfacial transport resistance, charge-transfer resistance, and SEI resistance at individual electrode-electrolyte interfaces within practical lithium-ion batteries. By leveraging frequency-dependent, thermal-wave sensing and interface-specific modeling, METS uniquely attributes interfacial properties to specific electrodes, as validated by comparison with traditional electrochemical impedance spectroscopy (EIS). The ability to spatially and temporally resolve interfacial processes in real time provides new diagnostic capabilities that are crucial for mechanistic studies of battery degradation and for the rapid development of next-generation energy storage systems.

Chalise, Divya [University of California, Berkeley↗

Direct Observation of Lattice Aluminum Environments in Li Ion Cathodes LiNi 1– y – z Co y Al z O 2 and Al-Doped LiNi x Mn y Co z O 2 via 27 Al MAS NMR Spectroscopy

Direct observations of local lattice aluminum environments have been a major challenge for aluminum -bearing Li ion battery materials, such as LiNi1-y-zCoyAlzO2 Al(NCA) and aluminum-doped LiNixMnyCozO2 (NMC). Al-27 magic angle spinning (MAS) nuclear magnetic resonance (NMR) spectroscopy is the only structural probe currently available that can qualitatively and quantitatively characterize lattice and nonlattice (i.e., surface, coatings, segregation, secondary phase etc.) aluminum coordination and provide information that helps discern its effect in the lattice. In the present study, we use NMR to gain new insights into transition metal (TM)-O-Al coordination and evolution of lattice aluminum sites upon cycling. With the aid of first-principles DFT calculations, we show direct evidence of lattice Al sites, nonpreferential Ni/Co-O-Al ordering in NCA, and the lack of bulk lattice aluminum in aluminum -"doped" NMC. Aluminum coordination of the paramagnetic (lattice) and diamagnetic (nonlattice) nature is investigated for Al-doped NMC and NCA. For the latter, the evolution of the lattice site(s) upon cycling is also studied. A clear reordering of lattice aluminum environments due to nickel migration is observed in NCA upon extended cycling.

27Al MAS NMR↗

New insights on electro-optical response of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) film to humidity

Understanding the relative humidity (RH) response of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is critical for improving the stability of organic electronic devices and developing selective sensors. In this work combined gravimetric sensing, nanoscale surface probing, and mesoscale optoelectronic characterization are used to directly compare the RH dependence of electrical and optical conductivities and unfold connections between the rate of water adsorption and changes in functional properties of PEDOT:PSS film. We report three distinct regimes where changes in electrical conductivity, optical conductivity, and optical bandgap are correlated with the mass of adsorbed water. At low (RH < 25%) and high (RH > 60%) humidity levels dramatic changes in electrical, optical and structural properties occur, while changes are insignificant in mid-RH (25% < RH < 60%) conditions. We associate the three regimes with water adsorption at hydrophilic moieties at low RH, diffusion and swelling throughout the film at mid-RH, and saturation of the film by water at high RH. Optical film thickness increased by 150% as RH was increased from 9% to 80%. Low frequency (1 kHz) impedance increased by ~100% and film capacitance increased by ~30% as RH increased from 9% to 80% due to an increase in the film dielectric constant. Finally, changes in electrical and optical conductivities concomitantly decrease across the full range of RH tested.

36 MATERIALS SCIENCE↗

Catalysis applications of size-selected cluster deposition

In this Perspective, we review recent studies of size-selected cluster deposition for catalysis applications performed at the U.S. DOE National Laboratories, with emphasis on work at Argonne National Laboratory (ANL) and Brookhaven National Laboratory (BNL). The focus is on the preparation of model supported catalysts in which the number of atoms in the deposited clusters is precisely controlled using a combination of gas-phase cluster ion sources, mass spectrometry, and soft-landing techniques. This approach is particularly effective for investigations of small nanoclusters, 0.5-2 nm (<200 atoms), where the rapid evolution of the atomic and electronic structure makes it essential to have precise control over cluster size. Cluster deposition allows for independent control of cluster size, coverage, and stoichiometry (e.g., the metal-to-oxygen ratio in an oxide cluster) and can be used to deposit on any substrate without constraints of nucleation and growth. Examples are presented for metal, metal oxide, and metal sulfide cluster deposition on a variety of supports (metals, oxides, carbon/diamond) where the reactivity, cluster-support electronic interactions, and cluster stability and morphology are investigated. Both UHV and in situ/operando studies are presented that also make use of surface-sensitive X-ray characterization tools from synchrotron radiation facilities. Novel applications of cluster deposition to electrochemistry and batteries are also presented. This review also highlights the application of modern ab initio electronic structure calculations (density functional theory), which can essentially model the exact experimental system used in the laboratory (i.e., cluster and support) to provide insight on atomic and electronic structure, reaction energetics, and mechanisms. As amply demonstrated in this review, the powerful combination of atomically precise cluster deposition and theory is able to address fundamental aspects of size-effects, cluster-support interactions, and reaction mechanisms of cluster materials that are central to how catalysts function. Lastly, the insight gained from such studies can be used to further the development of novel nanostructured catalysts with high activity and selectivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗