Search NASA⌕ Search

SEARCH · Search NASA

Results for “COMBUSTION PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

Fan Beam Emission Tomography Demonstrated Successfully in the Reduced-Gravity Environment of Drop Towers

Fires onboard manned spacecraft and launch vehicles are a particularly feared hazard because one cannot jump ship while in orbit 240 nmi above the Earth at 17 000 mph! Understanding the physical properties of fires in free fall and on orbit is, therefore, a very important endeavor for NASA s Human Exploration and Development of Space (HEDS) enterprise. However, detailed information concerning the structure of microgravity fires remained elusive until recently since robustness, limited power, limited volume, and limited mass place severe constraints on diagnostic equipment for use in space and in NASA Glenn Research Center s reduced-gravity facilities. Under NASA Research Associate funding since 2001, En'Urga, Inc. (Dr. Sivathanu, principal investigator, and Dr. Lim, co-investigator) in collaboration with Glenn (Dr. Feikema, coinvestigator) have successfully demonstrated a new technology for use in microgravity combustion. A midinfrared scanning spectrometer has been developed by En'Urga and tested at Glenn to measure 30 spectra per second at different spatial locations in a flame from 1.8 to 4.8 microns.

Feikema, Douglas A.↗

Effect of Aromaticity on Soot Formation: A Reactive Molecular Dynamics Study

This study investigates the formation of soot from n-dodecane and its blend with m-xylene under pyrolytic and low-oxygen conditions with reactive molecular dynamics (MD) simulations. ReaxFF force field is used to simulate the interactions of fuel and oxygen molecules at engine-relevant conditions (2500-3500 K and 70-75 bar). Fuel molecules with carbon atom density of 0.03 g/cm 3 are dispersed into a cube and constant temperature simulations are carried out with a Nosé-Hoover thermostat. Pyrolysis of n-dodecane and the chemical pathway towards the formation of aromatic hydrocarbons are investigated. The initial pyrolysis rate of n-dodecane is observed to be slightly higher with the addition of aromatic compounds and oxygen. While the first aromatics formed from the decomposed n-dodecane are phenyl radicals at 2500 K, decomposition of the aliphatic fuel compound is observed to be necessary to build a carbon cluster, and eventually soot. Morphological properties of the created soot particles are also analyzed. The maturity, size and aromatics content of the soot particle are slightly affected with the addition of m-xylene and oxygen at 3500 K within the 3 ns simulation time possibly due the formation of larger and more condensed aromatic rings, resulting in larger soot molecules. The outcomes of this study provide important insights into the formation mechanism of soot and its morphological characteristics depending on varying fuel concentrations at pyrolysis and low oxygen engine conditions. Results of this analysis will further contribute to the understanding of contrail formation on generated soot particles originated from the combustion of different chemical components with particle chemistry matching companion experiments.

soot formation↗

Initiation of Flash Boiling of Multicomponent Miscible Mixtures with Application to Transportation Fuels and Their Surrogates

This paper presents methodologies to predict thermodynamic conditions that initiate flash boiling by spontaneous nucleation of liquids consisting of hundreds of miscible liquids and their lower order surrogate mixtures. The methods are illustrated with a kerosene-based fuel and a seven-component surrogate for it. The predictions are compared to measurements of nucleation temperatures obtained from a pulse-heating technique that rapidly heats a microscale platinum film immersed in a pool of the test fluid. Nucleation temperatures are predicted using a generalized corresponding states principle (GCSP), and a modification of classical nucleation theory that considers the mixture as a pseudo single component fluid (PSCF). The intent is to offer a simple means to predict the initiation of flash boiling that can have important consequences for fuel efficiency in combustion engines. We show that contact angle has a strong effect such that predicted and measured spontaneous nucleation temperatures agree for a given heating rate only if contact angle is accounted for in the theory. For low heating rates (less than 2 × 10 7 K/s), predicted nucleation temperatures, assuming a spherical bubble, are 13% higher than measurements. The gap is closed to about 6% as the heating rate reaches 3 × 10 8 K/s (the highest that could be reached in the experiments) and to less than 1% when the measured nucleation temperature is extrapolated to an asymptotic (zero contact angle) limit. Here, the PSCF method (using mixture properties as mole fraction averages of mixture component properties evaluated at the same reduced temperatures as the mixtures) and the GSCP predict virtually identical nucleation temperatures, while the GCSP method does not require any mixture property values.

42 ENGINEERING↗

Development of a Data-Derived Sooting Index Including Oxygen-Containing Fuel Components

Particulate matter (PM) emissions from spark-ignited engines, particularly those with direct injection, now exceed those of light-duty diesel engines equipped with diesel particle filters. Fuel chemistry is one of several interacting factors that determine the amount of PM produced during combustion. Understanding the relationship between fuel chemistry and PM emissions is therefore essential in identifying fuels with a lower tendency to form soot. However, existing predictive models have been shown to perform poorly when fuel blends include a large proportion of oxygenated molecules. In this study, we report a new analysis of the data from the EPAct V2 data set with the objective of developing an emission index that adequately handles the effects of oxygenate blending on vehicle and engine emissions. Our approach uses regularized linear regression to select the most important parameters in predicting normalized vehicle emissions as a function of fuel composition and bulk fuel properties. Interestingly, our data-derived metric reproduces a similar functional form to the particulate matter index equation, including a chemical tendency to form soot as well as the vapor pressure. The resulting metric better predicts PM formation in the EPAct V2 data set as a function of fuel properties and composition than existing models.

30 DIRECT ENERGY CONVERSION↗

CHARACTERISTICS OF CYCLE-TO-CYCLE COMBUSTION VARIABILITY AT PARTIAL-BURN LIMITED AND MISFIRE LIMITED SPARK TIMING UNDER HIGHLY DILUTED CONDITIONS

Diluted combustion with exhaust gas recirculation (EGR) has been widely employed to improve the fuel economy of spark ignition engines. The combustion kinetics, however, are affected and the flame propagation speed is decreased. In order to compensate for this adverse effect, the spark timing needs to be recalibrated to achieve maximum brake torque (MBT). At high levels of EGR dilution, the spark timing is constrained by two ignition limits: 1) the partial-bum limit where the spark timing is retarded from MBT and 2) the misfire limit where the spark timing is too advanced. This work uses a probabilistic framework to capture the differences between both ignition limits. In particular, it introduces the concept of a nominal indicated mean effective pressure (IMEP) distribution based on the stochastic properties of the cycle-to-cycle variability (CCV) at nominal stable conditions. By defining a nominal band where fully burned cycles occur with high probability, we introduce a cycle classification method that can be used to 1) determine the level of randomness of misfire and partial-burn events, and 2) measure CCV. The new CCV metric based on the density of the nominal band is compared with the traditional coefficient of variation of IMEP (CoVIMEP). It is shown that the nominal band concept, together with the CoVIMEP, can help to discern between partial-burn limited and misfire limited conditions. Furthermore, the Kullback-Leibler divergence is used to demonstrate that the IMEP distribution is significantly different between nominal and partial-burn/misfire limited conditions. Experiments are carried at various EGR levels and spark timings while recoding in-cylinder pressure at steady state. Although the emphasis of this work is to characterize the differences of both ignition limits from a probabilistic point of view, similarities between partial-burn cycles at either limiting conditions are also discussed.

Maldonado, Bryan↗

Foreign Object Damage Resistance of Uncoated and EBC Coated SiC/SiC Composites

SiC/SiC composites fabricated by the melt infiltration method are candidate materials for the turbine components such as combustor liners, nozzle vanes and blades because of their high temperature strength, and thermal conductivity. To avoid surface recession in a combustion environment containing moisture, these materials also require an environmental barrier coating (EBC). Under thermal loading condition alone, the EBC coated SiC/SiC components show microstructural and strength stability after -1 5000 hr exposure to 12OO0C in combustion environment. However, the stability of SiC/SiC composites under impact conditions is not fully understood. In this study, both uncoated and EBC coated SiC/SiC composite specimens were impact tested by steel-ball projectiles at room temperature and at 1300 C in air. After impact, the specimens were analyzed under a scanning electron microscope to assess coating damage, and then tensile and bend tested at room temperature to determine their residual strength. The extent of coating and substrate damage with increasing projectile velocity was imaged and analyzed using nondestructive evaluation (NDE) methods such as micro focus x-ray radiography, tomography, and thermal wave imaging. The mechanical property results of impacted specimens are correlated with the NDE results and the scanning electron microscopy (SEM) observations. Influence of projectile velocity on impact damage of the coating/substrate, and the implication coating damage on durability of the composite will be discussed.

Bhatt, R. T.↗

Durability of YSZ Coated Ti2AlC in 1300 °C Mach 0.3 Burner Rig Tests

A thermal barrier coating system survived burner rig testing at 1300 °C for 500 h. A 160 µm thick yttria stabilized zirconia (YSZ) coating was applied to a Ti2AlC MAX phase bar sample by plasma spray physical vapor deposition (PS-PVD) and tested face-on in an atmospheric Mach 0.3 jet fuel burner, using 5-h thermal cycles. No thermal barrier coating (TBC) spallation or recession was observed, only a 2.4 mg/cm2 mass gain. The modest weight gain precluded severe volatility losses under high velocity burner conditions. The coating surface exhibited colonies of (111)flourite fiber-textured columns separated by craze patterns, with no visible moisture attack. The metastable tetragonal t' YSZ phase was obtained initially, transitioning to equilibrium teq and cubic YSZ, but with little detrimental monoclinic. The thickness of the alumina TGO was ~21 to 23 μm under the heated YSZ face and ~13 to 15 μm on the uncoated, cooler backside. The backside exhibited removal of initial transient TiO2 nodules and partial etching of the underlying Al2O3 scale by volatile hydroxides formed in high temperature, high velocity water vapor. Aerodynamic forces produced some bending of the cantilevered sample via creep. The test indicated exceptional stability of YSZ coatings on Ti2AlC under turbine conditions, with thermal expansion matching playing a key role. The purpose of this study was to demonstrate long term durability of YSZ/MAX phase system in aggressive high temperature burner rig testing. MAX phases have been keenly studied because of their unique crystal structure and intriguing properties (Refs. 1 and 2). Having Mn+1(Al,Si)(C,N)n general composition, they are defined as ceramics, but possess unusual desirable attributes such as high conductivity, thermal shock resistance, easy machinability, and deformation tolerance. The mechanical properties derive from weak M-(Al,Si) bonding in the basal plane that leads to sliding and kinking in preference to catastrophic crack growth. Like most ceramics they are phase stable at high temperatures, generally up to 1500 °C. High temperature oxidation resistance is excellent for alumina-forming Ti3AlC2, Ti2AlC, and Cr2AlC, as reviewed by Tallman, et al. (Ref. 3). Compatibility with α-Al2O3 scales is further enhanced in cyclic exposures by a close matching of thermal expansion coefficients, (Ref. 4) i.e., (~9.3, 10.2, 11.3×10–6/K for Al2O3, Ti2AlC, and YSZ, to be discussed). Turbine environments generally contain 10 percent water vapor in the combustion gases, therefore moisture effects can be a concern for some materials (Ref. 5). Furnace tests of MAX phases in high temperature steam generally showed little effect on Al2O3 scale growth (Ref. 6). However, high velocity and high pressure gas can influence scale losses by the formation of volatile reaction products, such as TiO(OH)2 and Al(OH)3 (Refs. 7 to 10). This phenomenon had been discussed for 1100 to 1300 °C high pressure burner rig tests of Ti2AlC (Ref. 11). A single cubic growth rate parameter kcubic was measurably lower than comparable furnace TGA data, but it could be matched reasonably well if corrected for a slight volatility term. In general, a two-parameter cubic-linear growth-volatility law was believed to apply. Corresponding scale volatility loss rates, directly measured at 1300 °C on a pre-oxidized sample, were moderate (0.012 mg/cm2/h) and largely attributed to removal of the initial TiO2 transient scale. A related CH4 burner study of high purity Cr2AlC MAX phase demonstrated 1200 °C durability after 500 rapid (5 min. heat and 2 min. cool) thermal shock cycling (29 h hot time) (Ref. 12). Heating and cooling rates were ~1000 and 500 °C per minute, with a gas velocity of 5 m/s, producing a 75 °C/mm gradient. A 7 μm Al2O3 surface scale and a 13 μm Cr7C3 depletion zone formed with no signs of failure. No evidence of scale volatility was evident, although weight change was not provided, the velocity was moderate, and the total hot time was not extensive. The same high gradient BRT was used to produce 1400 °C surface temperatures for a YSZ/Cr2AlC/IN738 system in the first study of MAX phases used as bond coats for thermal barrier coatings (TBC) (Ref. 25). Here TBC failure was reported after 745 cycles, with only a 1.5 μm Al2O3 scale entrained within a porous, Cr7C3 bondcoat depletion phase. YSZ thermal barrier coatings have been considered to be a compatible complement to Al-MAX phases because of thermal expansion matching and extremely low volatility in water vapor. Initial studies showed superior oxidative stability up to 1300 °C, for long times (at least 500 h) for Ti2AlC substrates and less (268 h) for Cr2AlC, while withstanding large alumina TGO scale thickness (~35 to 40 μm) (Refs. 13 and 14). By comparison, typical superalloy systems can only survive 1150 °C maximum interface temperatures for extended periods, with a maximum sustained TGO below 10 μm (Ref. 15). High temperature SiC based systems are known to form slow-growing SiO2 scales. But these are subject to rate enhancement and volatile Si(OH)4 products in the presence of water vapor, as described comprehensively by Opila, et al. (Refs. 5, 16 to 19). Net weight losses are generally observed in high velocity, high pressure burner rig studies (e.g., 0.084 mg/cm2/h at 1300 °C) (Ref. 20). Furthermore, the loss rates have been shown from chemical physics to scale with v1/2 and pH2O 2 (Ref. 16). Low activity, moisture-resistant environmental barrier coatings (EBC), such as rare earth silicates, are needed to prevent substrate recession under turbine conditions (Refs. 21 to 23).

Smialek, James L.↗

TGA Study of the Reaction Kinetics of a CuFeMnAlO 4+δ Oxygen Carrier for Methane Chemical Looping Combustion under High Pressure and Atmospheric Pressure Conditions

Reduction and oxidation kinetics of a CuFeMnAlO 4+δ oxygen carrier for methane were studied using an atmospheric thermogravimetric analyzer (TGA) and a pressurized TGA. Important parameters such as temperature (500–900 °C), particle size distribution (150–650 μm), and partial pressures of reactants (methane and oxygen) were evaluated. Results showed that the reduction of the oxygen carrier was not affected by particle size distribution studied in this work, and that above 750 °C, the effect of the temperature on oxygen carrier reduction started to diminish. The reaction time approaches an asymptotic limit as methane partial pressure increases. For oxygen carrier oxidation, it was found that the rate of oxidation increased with increasing oxygen concentration. The effect of the oxygen concentration was more noticeable when the oxygen concentration was below 7.5%. Because of the inherent feature of the oxygen carrier, its chemical looping with oxygen uncoupling property was also assessed. A phase boundary-controlled shrinking sphere model was used to model the test data from the TGAs. Modeling results showed that the oxygen carrier reduction had a reaction order of 1 with an activation energy of ∼46 kJ/mol. Oxygen carrier oxidation demonstrated a reaction order of 1.1 with an activation energy of ∼55 kJ/mol. Additionally, the differences of the experimental results between the atmospheric pressure TGA and the pressurized TGA were discussed in detail and the limitations of the pressurized TGA were highlighted.

Hydrocarbons↗

Trace Chemistry

The goals of the trace chemistry group were to identify the processes relevant to aerosol and aerosol precursor formation occurring within aircraft gas turbine engines; that is, within the combustor, turbine, and nozzle. The topics of discussion focused on whether the chemistry of aerosol formation is homogeneous or heterogeneous; what species are important for aerosol and aerosol precursor formation; what modeling/theoretical activities to pursue; what experiments to carry out that both support modeling activities and elucidate fundamental processes; and the role of particulates in aerosol and aerosol precursor formation. The consensus of the group was that attention should be focused on SO2, SO3, and aerosols. Of immediate concern is the measurement of the concentration of the species SO3, SO2, H2SO4 OH, HO2, H2O2, O, NO, NO2, HONO, HNO3, CO, and CO2 and particulates in various engines, both those currently in use and those in development. The recommendation was that concentration measurements should be made at both the combustor exit and the engine exit. At each location the above species were classified into one of four categories of decreasing importance, Priority I through IV, as follows: Combustor exit: Priority I species - SO3:SO2 ratio, SO3, SO2, and particulates; Priority II species: OH and O; Priority III species - NO and NO2; and Priority IV species - CO and CO2. For the Engine exit: Priority I species - SO3:SO2 ratio, SO3, SO2,H2SO4, and particulates; Priority II species: OH,HO2, H2O2, and O; Priority III species - NO, NO2, HONO, and HNO3; and Priority IV species - CO and CO2. Table I summarizes the anticipated concentration range of each of these species. For particulate matter, the quantities of interest are the number density, size distribution, and composition. In order to provide data for validating multidimensional reacting flow models, it would be desirable to make 2-D, time-resolved measurements of the concentrations of the above species and, in addition, of the pressure, temperature, and velocity. A near term goal of the experimental program should be to confirm the nonlinear effects of sulfur speciation, and if present, to provide an explanation for them. It is also desirable to examine if the particulate matter retains any sulfur. The recommendation is to examine the effects on SOx production of variations in fuel-bound sulfur and aromatic content (which may affect the amount of particulates formed). These experiments should help us to understand if there is a coupling between particulate formation and SO, concentration. Similarly, any coupling with NOx can be examined either by introducing NOx into the combustion air or by using fuel-bound nitrogen. Also of immediate urgency is the need to establish and validate a detailed mechanism for sulfur oxidation/aerosol formation, whose chemistry is concluded to be homogeneous, because there is not enough surface area for heterogeneous effects. It is envisaged that this work will involve both experimental and theoretical programs. The experimental work will require, in addition to the measurements described above, fundamental studies in devices such as flow reactors and shock tubes. Complementing this effort should be modeling and theoretical activities. One impediment to the successful modeling of sulfur oxidation is the lack of reliable data for thermodynamic and transport properties for several species, such as aqueous nitric acid, sulfur oxides, and sulfuric acid. Quantum mechanical calculations are recommended as a convenient means of deriving values for these properties. Such calculations would also help establish rate constants for several important reactions for which experimental measurements are inherently fraught with uncertainty. Efforts to implement sufficiently detailed chemistry into computational fluid dynamic codes should be continued. Zero- and one-dimensional flow models are also useful vehicles for elucidating the minimal set of species and reactions that must be included in two- and three-dimensional modeling studies.

Radhakrishnan, Krishnan↗

Demonstration of a Fiber Optic Regression Probe in a High-Temperature Flow

The capability to provide localized, real-time monitoring of material regression rates in various applications has the potential to provide a new stream of data for development testing of various components and systems, as well as serving as a monitoring tool in flight applications. These applications include, but are not limited to, the regression of a combusting solid fuel surface, the ablation of the throat in a chemical rocket or the heat shield of an aeroshell, and the monitoring of erosion in long-life plasma thrusters. The rate of regression in the first application is very fast, while the second and third are increasingly slower. A recent fundamental sensor development effort has led to a novel regression, erosion, and ablation sensor technology (REAST). The REAST sensor allows for measurement of real-time surface erosion rates at a discrete surface location. The sensor is optical, using two different, co-located fiber-optics to perform the regression measurement. The disparate optical transmission properties of the two fiber-optics makes it possible to measure the regression rate by monitoring the relative light attenuation through the fibers. As the fibers regress along with the parent material in which they are embedded, the relative light intensities through the two fibers changes, providing a measure of the regression rate. The optical nature of the system makes it relatively easy to use in a variety of harsh, high temperature environments, and it is also unaffected by the presence of electric and magnetic fields. In addition, the sensor could be used to perform optical spectroscopy on the light emitted by a process and collected by fibers, giving localized measurements of various properties. The capability to perform an in-situ measurement of material regression rates is useful in addressing a variety of physical issues in various applications. An in-situ measurement allows for real-time data regarding the erosion rates, providing a quick method for empirically anchoring any analysis geared towards lifetime qualification. Erosion rate data over an operating envelope could also be useful in the modeling detailed physical processes. The sensor has been embedded in many regressing media to demonstrate the capabilities in a number of regressing environments. In the present work, sensors were installed in the eroding/regressing throat region of a converging-diverging flow, with the working gas heated to high temperatures by means of a high-pressure arc discharge at steady-state discharge power levels up to 500 kW. The amount of regression observed in each material sample was quantified using a later profilometer, which was compared to the in-situ erosion measurements to demonstrate the efficacy of the measurement technique in very harsh, high-temperature environments.

Korman, Valentin↗

Dynamic modeling and control of a solid-sorbent CO{sub 2} capture process with two-stage bubbling fluidized bed adsorber reactor

Solid-sorbent-based CO{sub 2} capture processes have strong potential for reducing the overall energy penalty for post-combustion capture from the flue gas of a conventional pulverized coal power plant. However, the commercial success of this technology is contingent upon it operating over a wide range of capture rates, transient events, malfunctions, and disturbances, as well as under uncertainties. To study these operational aspects, a dynamic model of a solid-sorbent-based CO{sub 2} capture process has been developed. In this work, a one-dimensional (1D), non-isothermal, dynamic model of a two-stage bubbling fluidized bed (BFB) adsorber-reactor system with overflow-type weir configuration has been developed in Aspen Custom Modeler (ACM). The physical and chemical properties of the sorbent used in this study are based on a sorbent (32D) developed at National Energy Technology Laboratory (NETL). Each BFB is divided into bubble, emulsion, and cloud-wake regions with the assumptions that the bubble region is free of solids while both gas and solid phases coexist in the emulsion and cloud-wake regions. The BFB dynamic model includes 1D partial differential equations (PDEs) for mass and energy balances, along with comprehensive reaction kinetics. In addition to the two BFB models, the adsorber-reactor system includes 1D PDE-based dynamic models of the downcomer and outlet hopper, as well as models of distributors, control valves, and other pressure-drop devices. Consistent boundary and initial conditions are considered for simulating the dynamic model. Equipment items are sized and appropriate heat transfer options, wherever needed, are provided. Finally, a valid pressure-flow network is developed and a lower-level control system is designed. Using ACM, the transient responses of various process variables such as flue gas and sorbent temperatures, overall CO{sub 2} capture, level of solids in the downcomer and hopper have been studied by simulating typical disturbances such as change in the temperature, flowrate, and composition of the flue gas. To maintain the overall CO{sub 2} capture at a desired level in face of the typical disturbances, two control strategies were considered–a proportional-integral-derivative (PID)-based feedback control strategy and a feedforward-augmented feedback control strategy. Dynamic simulation results show that both the strategies result in unacceptable overshoot/undershoot and a long settling time. To improve the control system performance, a linear model predictive controller (LMPC) is designed. In summary, the overall results illustrate how optimizing the operation and control of carbon capture systems can have a significant impact on the extent and the rate at which commercial-scale capture processes will be scaled-up, deployed, and used in the years to come.

20 FOSSIL-FUELED POWER PLANTS↗

Co-Optimization of Fuels & Engines: FY16 Year in Review

The U.S. Department of Energy's (DOE) Co-Optimization of Fuels & Engines (Co-Optima) initiative is accelerating the introduction of affordable, scalable, and sustainable fuels and high-efficiency, low-emission engines with a first-of-its-kind effort to simultaneously tackle fuel and engine research and development (R&D). This report summarizes accomplishments in the first year of the project. Co-Optima is conducting concurrent research to identify the fuel properties and engine design characteristics needed to maximize vehicle performance and affordability, while deeply cutting emissions. Nine national laboratories - the National Renewable Energy Laboratory and Argonne, Idaho, Lawrence Berkeley, Lawrence Livermore, Los Alamos, Oak Ridge, Pacific Northwest, and Sandia National Laboratories - are collaborating with industry and academia on this groundbreaking research.

09 BIOMASS FUELS↗

Polybenzimidazole based random copolymers containing hexafluoroisopropylidene functional groups for gas separations at elevated temperatures

Polybenzimidazoles (PBIs) are attractive membrane materials for H 2 /CO 2 separation at hydrocarbon fuel derived synthesis gas operating conditions due to their exceptional physicochemical stability and promising permselectivity character. PBI molecular structure modification is a viable approach to disrupt chain packing altering the free-volume architecture which results in improved gas transport characteristics. This work is focused on the synthesis and characterization of novel PBI random copolymers for application as elevated temperature H 2 /CO 2 membranes. The co-polymerization route is expected to result in tailorable permeability and selectivity by combining the high H 2 permeability aspect of the highly disrupted loosely packed hexafluoroisopropylidene diphenyl group containing PBI segments (6F-PBI) with the highly selective tightly packed phenylene group containing PBI segments (m-PBI). 6F/m-PBI copolymers with varying 6F-PBI and m-PBI ratios having high inherent viscosity were synthesized. The structure and ratio of the 6F- and m-PBI fractions were confirmed using FTIR and NMR spectroscopic techniques. The measured gas transport properties of copolymer thin films cast in controlled environment were measured as a function of the operating conditions. Lastly, the H 2 permeability increased while H 2 /CO 2 selectivity decreased as the 6F-PBI copolymer fraction was increased.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Flight motor set 360T004 (STS-30R). Volume 1: System overview

The fourth NASA space shuttle flight incorporating redesigned solid rocket motors began on 4 May 1989. The flight motors were designated 360Q004A (left-hand) and 360H004B (right-hand); the mission was designated STS-30R. Overall engine performance was excellent. The low sample rate data that was available showed exceptional propulsion performance. All ballistic and mass property parameters closely matched the predicted values and were well within the required contract end item specification levels that could be assessed. No strain, vibration, or aft skirt heating environments could be addressed due to developmental flight instrumentation deletion. Infrared readings from the shuttle thermal imager were considered very good when compared with ground environment instrumentation readings taken during both the aborted and the actual countdowns. However, hand-held infrared gun reading/ground environment instrumentation comparisons were considered poor during both countdowns, with the exception of the T - 3 hour timeframe during the actual launch. Postflight inspection again verified superior performance of the insulation, phenolics, metal parts, and seals. All combustion gas was contained by the insulation in the field and case-to-nozzle joints. Inadequate parachute performance on the left-hand booster caused high splashdown loads, which resulted in a displaced nozzle and factory joint weatherseal unbond anomalies. Recommendations were made concerning improved thermal modeling and instruments. The rationale for these recommendations, the dispositions of all anomalies, and complete result details are given.

Ricks, Glenn A.↗

A model for the oxidative pyrolysis of wood

A generalized pyrolysis model (Gpyro) is applied to simulate the oxidative pyrolysis of white pine slabs irradiated under nonflaming conditions. Conservation equations for gaseous and solid mass, energy, species, and gaseous momentum (Darcy's law approximation) inside the decomposing solid are solved to calculate profiles of temperature, mass fractions, and pressure inside the decomposing wood. The condensed phase consists of four species, and the gas that fills the voids inside the decomposing solid consists of seven species. Four heterogeneous (gas/solid) reactions and two homogeneous (gas/gas) reactions are included. Diffusion of oxygen from the ambient into the decomposing solid and its effect on local reactions occurring therein is explicitly modeled. A genetic algorithm is used to extract the required material properties from experimental data at 25 kW/m{sup 2} and 40 kW/m{sup 2} irradiance and ambient oxygen concentrations of 0%, 10.5% and 21% by volume. Optimized model calculations for mass loss rate, surface temperature, and in-depth temperatures reproduce well the experimental data, including the experimentally observed increase in temperature and mass loss rate with increasing oxygen concentration. (author)

09 BIOMASS FUELS↗

A Simulation of the Effects of Varying Repetition Rate and Pulse Width of Nanosecond Discharges on Premixed Lean Methane-Air Combustion

Two-dimensional kinetic simulation has been carried out to investigate the effects of repetition rate and pulse width of nanosecond repetitively pulsed discharges on stabilizing premixed lean methane-air combustion. The repetition rate and pulse width are varied from 10 kHz to 50 kHz and from 9 ns to 2 ns while the total power is kept constant. The lower repetition rates provide larger amounts of radicals such as O, H, and OH. However, the effect on stabilization is found to be the same for all of the tested repetition rates. The shorter pulse width is found to favor the production of species in higher electronic states, but the varying effects on stabilization are also found to be small. Our results indicate that the total deposited power is the critical element that determines the extent of stabilization over this range of discharge properties studied.

Bak, Moon Soo↗

Airborne Dust in Space Vehicles and Habitats

Airborne dust, suspended inside a space vehicle or in future celestial habitats, can present a serious threat to crew health if it is not controlled. During the Apollo missions to the moon, lunar dust brought inside the capsule caused eye irritation and breathing difficulty to the crew when they launched from the moon and re-acquired "microgravity." During Shuttle flights reactive and toxic dusts such as lithium hydroxide have created a risk to crew health, and fine particles from combustion events can be especially worrisome. Under nominal spaceflight conditions, airborne dusts and particles tend to be larger than on earth because of the absence of gravity settling. Aboard the ISS, dusts are effectively managed by HEPA filters, although floating dust in newly-arrived modules can be a nuisance. Future missions to the moon and to Mars will present additional challenges because of the possibility that external dust will enter the breathing atmosphere of the habitat and reach the crew's respiratory system. Testing with simulated lunar and Martian dust has shown that these materials are toxic when placed into the lungs of test animals. Defining and evaluating the physical and chemical properties of Martian dusts through robotic missions will challenge our ability to prepare better dust simulants and to determine the risk to crew health from exposure to such dusts.

James, John↗

SAM™ (System Advisor Model™) [SWR-16-02, SWR-10-13]

See the SAM™ website to build a desktop version of the National Laboratory of the Rockies' (NLR's) System Advisor Model™ (SAM). https://sam.nlr.gov/ The System Advisor Model™ (SAM™) is a free techno-economic software model that facilitates decision-making for people in the renewable energy industry: -Project managers and engineers -Policy analysts -Technology developers -Researchers SAM can model many types of renewable energy systems: -Photovoltaic systems, from small residential rooftop to large utility-scale systems -Battery storage with Lithium ion, lead acid, or flow batteries for front-of-meter or behind-the-meter applications -Concentrating Solar Power systems for electric power generation, including parabolic trough, power tower, and linear Fresnel -Industrial process heat from parabolic trough and linear Fresnel systems -Wind power, from individual turbines to large wind farms -Marine energy wave and tidal systems -Solar water heating -Fuel cells -Geothermal power generation -Biomass combustion for power generation -High concentration photovoltaic systems SAM's financial models are for the following types of projects: -Residential and commercial projects where the renewable energy system is on the customer side of the electric utility meter (behind the meter), and power from the system is used to reduce the customer's electricity bill. -Power purchase agreement (PPA) projects where the system is connected to the grid at an interconnection point, and the project earns revenue through power sales. The project may be owned and operated by a single owner or by a partnership involving a flip or leaseback arrangement. -Third party ownership where the system is installed on the customer's (host) property and owned by a separate entity (developer), and the host is compensated for power generated by the system through either a PPA or lease agreement. For a more detailed description of SAM, see Blair et al. (2018), System Advisor Model (SAM) General Description (Version 2017.9.5), NREL/TP-6A20-70414. https://www.nrel.gov/docs/fy18osti/70414.pdf

Ryberg, David↗