Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

Thermo-Mechanical Analysis of SBLOCA with Loss of One Safety Injection System Using SCDAP/RELAP5

Design Extension Condition (DEC) for nuclear power plants has been being deliberated to bring it within a safety regulation boundary, following the 2011 Fukushima Daiichi accident. Moreover, a new regulation on the LOCA accident analysis designated as 10CFR50.45(c) has been proposed based on a concern of the non-conservatism of current criterion neglecting fuel burn-up effect on the cladding embrittlement. Therefore, a more comprehensive and realistic simulation of fuel rod behavior is required to cope with the stringent environment under LOCA accidents. A SCDAP/RELAP5 system analysis code has been used mainly on the prediction of severe accident phenomena. It has a set of mechanistic models for the fuel deformation, which plays an important role particularly in the early phase progression of the fuel melting. However, limited work has been done focusing on the models only to the fuel failure estimation through the DBA or candidates of DEC. Therefore, some analyses were performed here with a burnup dependent core model to understand the capability of SCDAP/RELAP5 to predict the thermo-mechanical behavior of the fuel cladding such as ballooning, burst and external/internal oxidation. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Computational Studies of Gas Phase Reactions of Zirconium Tetrachloride (ZrCl{sub 4}) and Metal Chloride Impurities

Zirconium-based cladding materials that surround used nuclear fuel (UNF) rods represent a significant fraction of the total amount of high level waste that must be disposed of in long term geological repositories. The decontamination, recovery and reuse of these materials would significantly reduce the high level waste associated with light water reactors and could provide a new source of hafnium free zirconium for the fabrication of new nuclear components. One part in the strategy to recycle zirconium from used cladding materials involves developing a computational modeling (DFT) protocol to understand the reactions between ZrCl{sub 4} and metal chloride impurities that may occur in the gas phase during sublimation. Several of the metal chloride species present are known to form Lewis acid/base adducts in the gas phase and development of purification protocols require investigation into the properties of these ZrCl{sub 4} contaminates.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Post-Irradiation Examination for Conventional and Advanced Nuclear Fuel

During irradiation in a nuclear reactor, the fuel pellet experiences non-uniform fission rate and strong thermomechanical loads, which result in alterations and restructuring occurring non-homogeneously in the fuel volume. The irradiated fuel is characterized by a highly heterogeneous structure, with a correspondingly heterogeneous distribution of phases and properties. It is a big technical challenge for a hot cell facility to be able to cover effectively a broad variety of fuel types and compounds, characterized by different compositions, physico-chemical properties, geometries and configurations. The first challenge is to provide testing environments and procedures which do not alter or degrade the original irradiated fuel properties and are technically suitable for hot cell or shielded facility operation. For instance, non-oxide fuel compounds require protective atmosphere to avoid sample oxidation during storage, preparation and testing. Moreover, suitable adaptations of tools and measuring devices must be available to characterize fuel configurations which differ from the conventional cylindrical pellet-cladding geometries (e.g. spherical fuel elements for pebble bed HTR and TRISO coated fuel particles). Finally, adequate scientific methods of investigation must be available to measure properties and study the behaviour of highly heterogeneous irradiated fuel. In addition to basic techniques for non-destructive and destructive examination of nuclear fuel systems (e.g. covering fuel and cladding or fuel and coatings, or other configurations), 'in-depth' methods are applied to determine physical, thermomechanical and micro-analytical properties of specific phases/features present in irradiated fuel. This paper presents relevant trends and examples from fuel safety studies performed at JRC-Karlsruhe and in other laboratories which highlight the 'added value' obtainable by applying combined techniques, high resolution tools or 3D methods of analysis for the experimental 'multiscale' characterization of irradiated fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Comparison of Thermal Diffusivity Degradation of Irradiated Zirlo and SiC-SiC Composite

Zirlo (Zircaloy cladding material from Westinghouse) has been widely used as the fuel cladding material in Light Water Reactors because of its high melting point, low susceptibility to corrosion, good thermal and mechanical shock resistance, and low degradation of mechanical properties under irradiation. But as Zirlo reacts with water at high temperature, which can trigger serious accidents, efforts have been made to explore better candidates to replace Zirlo in the water-cooled reactors. SiC-SiC composite is considered as one of the most viable options due to its comparable mechanical performances and corrosion resistance. However, one of the most important properties, thermal diffusivities of both Zirlo and SiC-SiC composite, and their degradation after irradiation, are not well known yet. Ion-irradiated samples are used to study the thermal property degradation caused by irradiation instead of the neutron-irradiated ones due to the significantly lower radioactivity. The microstructural damage is estimated from the software simulation SRIM/TRIM based on the energy and fluence of the ion, and the target material, and represented by DPA (displacement by atom). Different from neutron-irradiated samples, the damaged layer of ion-irradiated samples is only a few to a few tens of micrometers thick, and the damage is depth dependent. It is impossible to directly measure the bulk property change, and a microscale measurement technique is necessary. Laser-based photothermal reflectance technique is one of the ideal methods to measure local thermal conductivity and diffusivity with high spatial resolution. The main principle of this technique is to heat the solid sample using an intensity-modulated laser, and scan the sample with a constant intensity continuous-wave (CW) laser to detect the thermal wave propagation. On bulk, isotropic material, if the heating laser intensity is modulated as a sine wave, thermal diffusivity of the sample can be derived from the phase lag of the thermal wave, scan distance and modulation frequency in a straight forward manner. By using more specific analytical models, thermal conductivity and diffusivity in complicated cases, such as layered structure materials, composite materials, and/or anisotropic materials, are measurable as well. In this work, thermal diffusivity of the light damage layer of the post-irradiation Zirlo and SiC-SiC composite are measured and compared. The Zirlo sample is irradiated by Ni{sup 9+} ion, and SiC-SiC composite material is irradiated by Si{sup 7+} ion. The peak DPA of both sample is similar as ∼10. For ion-irradiated materials, DPA is known to increase with depth before it reaches the peak, and then sharply drop to zero. In term of light damage layer in this manuscript, we mean by the layer with a DPA smaller than 5% maximum value. In this layer DPA increases slowly and smoothly with depth, and the structure and thus thermal properties are more spatially uniform. For the SiC-SiC composite, the measurements are separately conducted on fibers along radial or axial direction, and on the matrix. Our measurement results show that with similar microstructural damage, thermal diffusivity of matrix SiC reduces more significantly than that of Zirlo. For fiber SiC that has a much lower thermal diffusivity than the matrix SiC before irradiation, the post-irradiation effect on thermal diffusivity is not obvious.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Theoretical Investigation of the Chemical Behaviour of Irradiated U-Mo/Mg Fuel

A significant international effort has been put forth to replace Highly Enriched Uranium (HEU) fuel used in research and test reactors with Low Enriched Uranium (LEU) fuel to reduce proliferation concerns. Furthermore, some fuel processing issues have been encountered with some LEU candidate fuel designs. In order to address both of the foregoing issues, new fuel designs must be developed. One of these designs has U-Mo particles dispersed in a Mg matrix (U-Mo/Mg) that is cladded in an Al-alloy. While characterization analyses and thermophysical measurements have been reported for fresh U-Mo/Mg fuel, the effects of irradiation are not yet well known nor are they understood. Given that earlier international campaigns that investigated U-Mo/Al as a candidate fuel design resulted in consistent failures due to the formation of an interaction layer between the U-Mo fuel particles and Al meat, it seems prudent to theorize and predict any phases that may form as a result of irradiation of U-Mo/Mg fuel. The formation of these phases and any interaction that they may have with the cladding may potentially affect the reliability of this fuel design. This short paper provides a preliminary theoretical framework for the prediction of minor phases that may appear in irradiated U-Mo/Mg research reactor fuel, which should be confirmed via postirradiation examination at a later time.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effect of Interaction Layer and U-Mo Size on Pore Growth in U-Mo/Al Fuel

U-Mo/Al dispersion fuel, composed of U-Mo alloy fuel particles embedded in the aluminum (Al) matrix, has been developed to convert high-enriched uranium fuel to low-enriched uranium for high-performance research reactors. The fueled zone, referred to as 'fuel meat,' is clad with aluminum alloy. Fuel meat and cladding are metallurgically bonded during fabrication. Irradiated U-Mo/Al dispersion fuel has shown stable performance in low fission rate and burnup ranges. However, excessive fuel meat swelling or breakaway swelling, which is believed an incipient failure, was observed at higher fission rate and burnup conditions. This breakaway swelling is believed to be a result from the combination of accelerated fuel swelling and interconnection of large pores formed outside of the UMo particles. These large pores were frequently found, particularly, at the interface between the Al and the fuel-matrix interaction layer (IL) that formed by irradiation-enhanced interdiffusion of U-Mo and Al. Kim et al. developed a model for pore growth using a mechanical equilibrium between gas pressure in the pore, interfacial energies, and the external stress at the pore surface. In this model, IL provides a path way for fission gas to reach the pores and also generates tensile stress fields. Hence, suppressing IL growth by applying a diffusion barrier, like a coating of the U-Mo particles, appears to be an effective method to prevent pore formation. Another remedy to prevent pore formation is to use large U-Mo fuel particles. Using larger U-Mo particles was thought advantageous because it reduces fission gas release. In this study, the effect of IL growth and U-Mo particle size on pore formation is examined using the model. The advantage was quantified in terms of porosity.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Study on Neutronics Calculation Method of SCWR with Annular Fuel Assembly

Supercritical Water-Cooled Reactor (SCWR) is one of Gen-IV reactor systems for its advantages over LWRs, such as high thermal efficiency, simplified reactor system and economics. Annular fuel was proposed by MIT to supplant conventional solid fuel and improve power density in LWRs. Annular fuel is cooled from both inside and outside of the fuel. Thus a lower fuel temperature and cladding surface temperature can be achieved with higher power density. SCWRs will benefit from this advantage because high cladding temperature (usually over 650 degree C) is one challenge of SCWRs. Using annular fuel in SCWRs is very promising. This is also because the inner hole of the annual fuel can provide extra neutron moderation. Supercritical water density is too low to provide enough moderation. Different analysis codes have been developed all over the world to carry out SCWR pre-conceptual core design. Yamaji et al. developed SRAC/ASMBURN/COREBN to study Japan version of SCWR. Monti et al. used ERANOS to analyze HPLWR (High Performance Light Water Reactor). WIMS-D4/CITATION was also used to calculate HPLWR by Tashakor et al.. These codes employ a two-step method used in PWRs calculation. Lattice/Assembly calculation is carried out as the first step. In the second step, few group constant of different fuel assembly types is then used in core calculation. MCNP had also been used to study SCWR by Watta et al.. Due to large computation time cost, it's used mostly to analyze fuel assembly or core performance rather than pre-conceptual design, in which much optimization is needed. In this research, a neutronics calculation code for SCWR is developed using two-step method. This code is verified by comparing with Monte-Carlo code. Fuel assembly homogenization method is studied to improve the code accuracy.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Improved Safety Injection Flow Map Associated with Target RCS Depressurization to Maintain Core Coolability of OPR1000

In Korea, Severe Accident Management Guidance (SAMG) for Optimized Power Reactor (OPR1000) has been developed through the research results related to the WOG SAMG, in which the operation phase shifts from the Emergency Operation Procedure (EOP) to the SAMG when the Core Exit Temperature (CET) reaches 923 K. Among 7 mitigation strategies envisioned, the third management strategy, injecting coolant into Reactor Coolant System (RCS) by depressurizing the RCS is one of the key strategies to fortify the in-vessel retention capability. As an aid to such mitigation strategy, a safety injection (SI) flow map has been developed by Lee et al. for predicting required flow rate associated with target RCS depressurization to recover in-vessel coolability. The mechanistic SI flow map used the CET increase rate and core water level decrease rate obtained from MELCOR code simulation. It should be noted that during the severe accident, the total heat generated is sum of the decay heat and the oxidation heat. Thus, it is necessary to consider additional heat sources by oxidation reaction between cladding, structure, control rod, and hot steam prior to the injection of coolant. It was believed that the SI model estimated required flow rate rather conservatively by considering the expected amount decay heat and the accumulated heat in the core based on the RCS pressure. However, it was confirmed that the SI model developed by Lee et al. could not represent the total heat removal especially since start of oxidation. Under transient conditions, the heat sources accumulated in the heat structures (fuel, cladding, supporting structures) should be embarked in the model for accurate contribution of the total heat source to the required flow rate. Therefore, the objective of this study is to improve the previous SI flow map predicting the injection flow rate associated with target RCS depressurization to satisfy the in-vessel coolability during severe accidents. Additional terms were developed to reflect accurate heat accumulating and included in the existing model. Resulting SI flow map includes the target RCS depressurization, which enables discharge of the required flow rate by utilizing the flow rate-pressure curve with operation of two high pressure safety injections (HPSIs). Also recent MELCOR simulation result of a postulated steam generator tube rupture (SGTR) accident verified the accuracy of the improved map.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Advanced Fuel/Cladding Testing Capabilities in the ORNL High Flux Isotope Reactor

The ability to test advanced fuels and cladding materials under reactor operating conditions in the United States is limited. The Oak Ridge National Laboratory (ORNL) High Flux Isotope Reactor (HFIR) and the newly expanded post-irradiation examination (PIE) capability at the ORNL Irradiated Fuels Examination Laboratory provide unique support for this type of advanced fuel/cladding development effort. The wide breadth of ORNL's fuels and materials research divisions provides all the necessary fuel development capabilities in one location. At ORNL, facilities are available from test fuel fabrication, to irradiation in HFIR under either thermal or fast reactor conditions, to a complete suite of PIEs, and to final product disposal. There are very few locations in the world where this full range of capabilities exists. New testing capabilities at HFIR have been developed that allow testing of advanced nuclear fuels and cladding materials under prototypic operating conditions (i.e., for both fast-spectrum conditions and light-water-reactor conditions). This paper will describe the HFIR testing capabilities, the new advanced fuel/cladding testing facilities, and the initial cooperative irradiation experiment that begins this year.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Dispersion flattened extremely high-birefringent kagome lattice elliptic core photonic crystal fiber in THz regime

A highly birefringent elliptic porous-core photonic crystal fiber with kagome lattice cladding has been presented for terahertz (THz) wave transmission. The slotted airholes inside the elliptic core effectively disrupt the symmetry of the porous-core which offers extremely high modal birefringence whereas the kagome cladding structure results in significantly low effective material loss (EML). The birefringence of the proposed structure is 9.73×10{sup −2} and the EML is 0.056 cm{sup −1} for y-polarized mode at an operating frequency of 1 THz. The suggested structure also provides very flat dispersion over a bandwidth of 300 GHz. It is highly expected that this elliptic core waveguide would be remarkably useful in numerous polarization maintaining THz applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Graphene oxide coated side polished surface plasmon resonance optical fibre sensor with varying polishing losses

Four batches of side-polished SMF optical fibres with different polishing losses, − 0.5 dBm, − 5 dBm, − 10 dBm and − 15 dBm were coated with a graphene oxide layer of ~ 0.5 μm via drop casting. TE polarized light was propagated through the light during experiments and four different transformer oils with different water contents were dropped onto the sensor. The drop in the power of transmitted light was recorded. The responses of the sensors showed good linearity for all, but the least polished fibre showed the weakest response in terms of power drop towards change in concentration. The − 5 dBm fibre showed the best response per unit concentration change. Additional tests showed the increased response for a GO coated side polished sensor compared to an uncoated side polished sensor. Simulation using COMSOL was performed to show the effects on the electric field of a sensor with and without GO coating. Another set of simulations were performed to show the effects of reducing cladding thickness on the coupling of the electric field. Simulations show that the optimal cladding thickness is not the most polished fibre, coinciding with our results that − 15 dBm loss fibre did not show the most response per unit change in the analyte.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Characterization of Irradiated Metal Waste from the Pyrometallurgical Treatment of Used EBR-II Fuel

As part of the pyrometallurgical treatment of used Experimental Breeder Reactor-II fuel, a metal waste stream is generated consisting primarily of cladding hulls laden with fission products noble to the electrorefining process. Consolidation by melting at high temperature [1873 K (1600 degrees C)] has been developed to sequester the noble metal fission products (Zr, Mo, Tc, Ru, Rh, Te, and Pd) which remain in the iron-based cladding hulls. Zirconium from the uranium fuel alloy (U-10Zr) is also deposited on the hulls and forms Fe-Zr intermetallics which incorporate the noble metals as well as residual actinides during processing. Hence, Zr has been chosen as the primary indicator for consistency of the metal waste. Recently, the first production-scale metal waste ingot was generated and sampled to monitor Zr content for Fe-Zr intermetallic phase formation and validation of processing conditions. Chemical assay of the metal waste ingot revealed a homogeneous distribution of the noble metal fission products as well as the primary fuel constituents U and Zr. Microstructural characterization of the ingot confirmed the immobilization of the noble metals in the Fe-Zr intermetallic phase.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Metallurgical Investigation of the Direct Energy Deposition Surface Repair of Ferrous Alloys

Among additive manufacturing (AM) processes, the direct energy deposition (DED) by laser is explored to establish its applicability for the repair of ferrous alloys such as UNS G41400 low-alloy steel, UNS S41000 martensitic stainless steel, UNS S17400 precipitation-strengthened martensitic stainless steel, and UNS S32750 super-duplex stainless steel. Unlike plating, thermal spray, and conventional cladding weld, DED laser powder deposition offers potential advantages, e.g., thin deposits, limited dilutions, narrow heat-affected zones (HAZ), potentially improved surface properties. In this investigation, all AM deposits were completed with an IREPA CLAD™ system using a powder feed of UNS N06625, an alloy largely selected for its outstanding corrosion resistance. This investigation first addresses topological aspects of AM deposits (including visual imperfections) before focusing on changes in microstructure, microhardness, chemical composition across AM deposits and base materials. It has been established that dense, uniform, hard (~ 300 HVN), crack-free UNS N06625-compliant AM deposits of fine dendritic microstructures are reliably produced. However, except for the UNS S32750 steel, a significant martensitic hardening was observed in the HAZs of UNS G41400 (~ 650 HVN), UNS S41000 (~ 500 HVN), and UNS S17400 (~ 370 HVN). In summary, this investigation demonstrates that the DED laser repair of ferrous parts with UNS N06625 may restore damaged surfaces, but it also calls for cautions and complementary investigations for alloys experiencing a high HAZ hardening, for which industry standard recommendations are exceeded and lead to an increased risk of delayed cracking in corrosive environments.

36 MATERIALS SCIENCE↗

Study of Thermomechanical Behavior of Zirconium-0.3 Tin Alloy

Zirconium-based alloys are used in the manufacturing of nuclear fuel tubes. These tubes need to be clad with zirconium-tin (Zr-0.3 wt.% Sn) alloy to enhance the lives of tubes. Manufacturing of such clad tubes is a challenging task, due to work hardening and dynamic softening phenomenon. In this study, hot deformation behavior of Zr-0.3Sn alloy is investigated at different temperatures and strain rates. It is found that fully recrystallized microstructure can be obtained by working at around 900 °C and high strain rate of 10 s{sup −1}. Further, constitutive equations are developed for the entire domain of deformation range and fitted into standard FEM-based simulation model for extrusion. The simulation results are validated with experimental data. The difference in flow stresses values obtained from numerical and experimental methods was around 14%.

36 MATERIALS SCIENCE↗

Diffusion Barrier Selection from Refractory Metals (Zr, Mo and Nb) via Interdiffusion Investigation for U-Mo RERTR Fuel Alloy

U-Mo alloys are being developed as low enrichment monolithic fuel under the Reduced Enrichment for Research and Test Reactor (RERTR) Program. Diffusional interactions between the U-Mo fuel alloy and Al-alloy cladding within the monolithic fuel plate construct necessitate incorporation of a barrier layer. Fundamentally, a diffusion barrier candidate must have good thermal conductivity, high melting point, minimal metallurgical interaction, and good irradiation performance. Refractory metals, Zr, Mo, and Nb are considered based on their physical properties, and the diffusion behavior must be carefully examined first with U-Mo fuel alloy. Solid-to-solid U-10wt.%Mo vs. Mo, Zr, or Nb diffusion couples were assembled and annealed at 600, 700, 800, 900 and 1000 degrees C for various times. The interdiffusion microstructures and chemical composition were examined via scanning electron microscopy and electron probe microanalysis, respectively. For all three systems, the growth rate of interdiffusion zone were calculated at 1000, 900 and 800 degrees C under the assumption of parabolic growth, and calculated for lower temperature of 700, 600 and 500 degrees C according to Arrhenius relationship. The growth rate was determined to be about 10 3 times slower for Zr, 10 5 times slower for Mo and 10 6 times slower for Nb, than the growth rates reported for the interaction between the U-Mo fuel alloy and pure Al or Al-Si cladding alloys. Zr, however was selected as the barrier metal due to a concern for thermo- mechanical behavior of UMo/Nb interface observed from diffusion couples, and for ductile-to-brittle transition of Mo near room temperature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Radiation Effects on the Microstructure of a 9Cr-ODS Alloy

Oxide dispersion strengthened (ODS) steels are a prime candidate for high temperature, high dose cladding in advanced nuclear reactors. A 9Cr-ODS alloy was irradiated with 5 MeV Ni ions at temperatures of 500, 600 and 700ºC to doses up to 150 dpa. There was no significant change in the dislocation arrangement. For oxide particles, there is a small shrinkage in size and increase in density with increasing irradiation dose. The atom probe analysis on the unirradiated and the Ni ion irradiated 9Cr-ODS at 700ºC to 150 dpa shows similar spatial configuration of oxide particles. Radiation-induced void swelling was not identified following Ni ion irradiation. Irradiation with 1.0 MeV Kr ions at temperatures of 500, 600, 700 and 800ºC to doses of 30-50 dpa reveals the presence of voids in all the irradiation conditions and it is believed to be due to Kr ions trapped in the materials. This work confirms that oxide particles and the microstructure of the 9Cr- ODS show minimal and acceptable changes under irradiation at temperature up to 700ºC and doses up to 150 dpa.

36 MATERIALS SCIENCE↗

Modeling of complex wear behavior associated with grid-to-rod fretting in light water nuclear reactors

One significant concern in the operation of light water nuclear reactors is the fretting wear damage to fuel cladding from flow-induced vibrations. For years, research on the grid-to-rod fretting (GTRF) phenomena has been underway in countries where nuclear power production is a significant industry. Under the auspices of the U.S. Department of Energy Consortium for Advanced Simulation of Light Water Reactors, an effort has been underway to develop and test an engineering wear model for zirconium alloy fuel rod cladding against a supporting grid. Furthermore, the multi-stage model accounts for oxide layers and wear rate transitions. Our paper describes the basis for a GTRF engineering wear model, the physical significance of the wear factor it contains, and recent progress toward model validation based on a fretting wear testing apparatus that accounts for coolant temperature, pressure, and the presence of periodic impacts (gaps) in grid/rod contact.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗