Search NASA⌕ Search

SEARCH · Search NASA

Results for “Device”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

A Simple Control to Reduce Device Over-Voltage Caused by Non-Active Switch Loop in Three-Level ANPC Converters

With the development of wide band-gap (WBG) technology, the switching speed of power semiconductor devices increases, which makes circuits more sensitive to parasitics. For three-level active neutral point clamped (3L-ANPC) converters, the over-voltage caused by additional non-active switch loop can be an issue. This paper analyzes the multiple commutation loops in 3L-ANPC converter and summarizes the impact factors of the device over-voltage. The nonlinearity of the output capacitance of the device can significantly influence the over-voltage. A simple control without introducing additional hardware circuit or complex software algorithm is proposed to attenuate the effect of the nonlinear output capacitance. Multi-pulse test is conducted for a 3L-ANPC converter built with silicon carbide (SiC) MOSFETs. With the proposed control, the testing results show that the peak drain-source voltage of both active and non-active switches is reduced by more than 20% compared to the conventional control.

Gui, Handong↗

Modeling of Multi-Loops Related Device Turn-On Overvoltage in 3L-ANPC Converters

An analytical model for the device drain-source turn-on overvoltage in three-level active neutral point clamped (3L-ANPC) converters is established in this paper. Considering the two commutation loops in the converter, the relationship between the turn-on overvoltage and the loop inductances is evaluated. The line switching frequency device usually exhibits higher overvoltage, while the high switching frequency device is not strongly influenced by the multiple loops. A 500 kVA 3L-ANPC converter using SiC MOSFETs is tested, and the model is verified with the experimental results.

Gui, Handong↗

Active Gate Current Control for Non-Insulating-Gate WBG Devices

This paper proposes an Active Gate Current Control (AGCC) strategy for non-insulating gate WBG devices, for example, gallium nitride gate-injection-transistor (GaN-GIT) and silicon carbide super junction transistor (SiC-SJT). It provides a tool for power converter designers to further improve the converter efficiency and to extend the life time of those higher cost power transistors. By continuously adjusting the device gate current, the proposed AGCC strategy can control the device switching speed, switching loss, conduction loss and gate loss together to achieve operation goals, including lower semiconductor loss, lower thermal stress, lower EMI spectrum, or smaller voltage overshoot across the full range

dv/dt↗

An Analog Active Gate Drive Circuit Architecture for Wide Band Gap Devices

With the increased usage of SiC and GaN devices in power converters, it is apparent to engineers that the benefits of these devices for low switching losses have to be balanced against two deterrents: (1) the faster rise and fall times of these devices lead to increased harmonic content, making it more difficult to meet Electromagnetic Compatibility (EMC) regulations; and (2) increased sensitivity to parasitic elements in the board layout, leading to higher dv DS /dt and di D /dt with higher current and voltage peak stresses. "Active" gate drives are thus needed to regulate different regions of switching to achieve the optimal tradeoff between switching loss and EMC. We present a simple analog circuit architecture for an active gate drive. Turn on and turn off tests with SiC modules and discrete parts are discussed with experimental results.

Ramabhadran, Ramanujam↗

Real-Time Lifetime Prediction of Semiconductor Devices Using Hardware-in-the-Loop

This paper presents a unique approach to enable real-time lifespan prediction of semiconductor power modules using a Hardware-in-the-Loop (HIL) system. By integrating the module's overall loss characteristics-specifically switching and conduction losses-with a thermoelectric model of the thermal management system, this research demonstrates that the model can dynamically estimates the junction temperature profile of the semiconductor devices in response to a changing torque demand profile for the motor drive system. This capability enables continuous monitoring of the module's operational time and cumulative stress induced on the devices to compute accumulated remaining lifetime or time-to-failure (TTF). This study provides an architectural framework for the HIL system with high-fidelity component models of multiple physical domains, allowing simulation of dynamic behaviors of a closely-coupled motor drive system. The advanced real-time computation and measurement functionalities of the HIL system allow for both dynamic lifetime calculations based on simulated data and aggregate lifetime predictions utilizing historical data. Moreover, this paper details an algorithm that not only computes cumulative damage but also synthesizes these data into a comprehensive aggregated lifetime metric. This methodology can enhance the maintenance scheduling strategies and operational reliability of semiconductor devices in critical applications, ultimately extending their service life while optimizing performance.

hardware-in-the-loop (HIL)↗

Recent Advancements in Reconfigurable mmWave Devices Based on Phase-Change and Metal Insulator Transition Materials

Chalcogenide Phase Change Materials (PCM) and metal insulator transition (MIT) materials are a group of materials that are capable of switching between low resistance and high resistance states. These emerging materials have been widely used in optical storage media and memory devices. Over the past recent years, there have been interests in exploiting the PCM and MIT materials, especially germanium antimony telluride (GST) alloys and vanadium dioxide (VO 2 ), for radio frequency (RF) applications. The PCM and MIT-based RF devices are expected to bridge the gap between semiconductor switches and microelectromechanical system (MEMS) switches as they combine the low insertion loss performance of MEMS technology and the small size and reliability performance of semiconductor technology. This article presents an overview of the PCM and MIT materials for RF circuits and discusses the recent advancements in reconfigurable millimeter-wave (mmWave) devices based on PCM and MIT materials in depth.

36 MATERIALS SCIENCE↗

Self-Cooling Multiferroic Magnetic Devices

Increasing switching frequency reduces magnetic volume, but conventional ferrites, used from tens to hundreds of kilohertz, cannot sustain the temperature and frequency ranges demanded by current and emerging wide bandgap and ultrawide bandgap devices. Here, this work presents a novel magnetic material architecture combining nanocrystalline magnetic material and multiferroic layers for megahertz power conversion. The high saturation flux density of nanocrystalline alloys supports miniaturization but is traditionally constrained by excessive losses above 10 kHz. A revolutionary multiferroic material with solid-state cooling via caloric materials is defined that will enable the next generation of magnetic devices for wide-bandgap-integrated designs. This letter highlights the fundamental physics behind this capability alongside early development of a finite element analysis for the multiferroic-based magnetic device using ANSYS, showing that the core achieves more uniform thermal distribution and reduces peak temperature by 9 ° C compared to conventional ferrites.

Soft magnetic materials↗

RanCompute: Computational Security in Embedded Devices via Random Input and Output Encodings

An embedded device in an insecure environment is subject to additional security risk through capture and reverse-engineering by a capable adversary. If this device contains a microchip performing sensitive computations, capture of the chip may leak functionality to an adversary. In this paper we propose a novel method in which we randomly encode the input operands and the outputs of a computation, thus not revealing the arithmetic operations being performed. The operations are sequenced in a graph representing the overall application. Once the initialization values are overwritten and lost, the results of these computations are indecipherable by the device performing the calculations as well as by any adversary. The result is transmitted back to a secure server which has stored the initialization values and so can decode the results which appear random to the adversary.

Embedded computing↗

Impact of Geomagnetic Induced Current Neutral Blocking Devices on Distance Relays in Sub-transmission Networks with IBR

Geomagnetically induced currents (GICs) can flow through transmission lines during geomagnetic disturbances, such as solar flares or coronal mass ejections. These currents can cause problems like transformer saturation and equipment damage. The most common method of mitigating GICs involves installing GIC neutral blocking devices (NBDs) in transformer neutrals. However, the wide application of capacitive GIC blocking devices may have unintended adverse effects on other devices, such as distance protection relays. As the number of inverter-based resources being connected to the transmission and sub-transmission systems increases, the likelihood of a sub-transmission line protected by a distance relay connected to a transformer with NBDs is increasing. Therefore, distance relays fed by IBRs and transmission lines with GIC-NBDs must be studied. This paper studies the effect of GIC-NBDs on a 69kV sub-transmission line of various lengths fed by a 25 MVA IBR and synchronous source. This work focused on the behavior of the GIC-NBDs using the measured apparent phase-to-ground and phase-to-phase impedance calculated by the relay and the source impedance ratio (SIR) during various electrical faults.

Patel, Trupal R [Sandia National Laboratories (SNL↗

Vortex Induced Vibration Test of the WITT Device in a Tidal Channel

Fluid flow around a bluff body causes vibrations as the boundary layer separates and vortices are shed. This phenomenon, called vortex induced vibration (VIV), is minimized in most engineering applications, but can be utilized for power generation. Vortex induced vibration has potential for energy harvesting in low velocity water flows and therefore could open many locations to marine renewable energy. Here we present the results of a field test of a device that utilizes VIV to harvest energy from flow in a tidal channel. The pendulum-type device has been designed to generate electricity from motion around and along three axes. It is named the Whatever Input to Torsion Transfer (WITT) energy device and in this test is mounted on top of a pipe. During the field test, the WITT generated electricity at flow velocities from 0.27 to 2.82 m/s. The field test has proven that the WITT can utilize VIV to produce electricity and charge a battery in tidal flows with velocities as low as 0.27 m/s. In the future, the electricity could be used to charge a battery for ocean observation instruments such as temperature and nitrate sensors. In-situ power generation by the WITT would extend deployment times and increase the frequency of measurements.

Branch, Ruth A.↗

Investigation of Junction Properties in CdS/CdTe Solar Cells and Their Correlation to Device Properties: Preprint

Secondary-ion mass spectrometry analysis of the CdS/CdTe interface shows that S diffusion in CdTe increases with substrate temperature and CdCl2 heat treatment. There is also an accumulation of Cl at the interface for CdCl2-treated samples. Modulated photo-reflectance studies shows that devices with CdCl2 heat treatment and open-circuit voltage (Voc) of 835 mV have a distinct high electric-field region in the layer with bandgap of 1.45 eV. Electron-beam induced current measurements reveal a one-sided junction for high Voc devices. The nature of the junction changes with processing. For heterojunction devices, the depletion region includes the highly defective CdS/CdTe interface, which would increase the recombination current and consequently the dark current, leading to lower Voc. In the case of CdCl2-treated cells, the n+-p junction and its high electric-field results in the junction between structurally compatible CdTe and the Te-rich CdSTe alloy, and thus, in higher Voc.

14 SOLAR ENERGY↗

Effect of Back Contact and Rapid Thermal Processing Conditions on Flexible CdTe Device Performance

Flexible CdTe solar cells on ultra-thin glass substrates can enable new applications that require high specific power, unique form-factors, and low manufacturing costs. To be successful, these cells must be cost competitive, have high efficiency, and have high reliability. Here we present back contact processing conditions that enabled us to achieve over 16% efficiency on flexible Corning (R) Willow (R) Glass substrates. We used co-evaporated ZnTe:Cu and Au as our back contact and used rapid thermal processing (RTP) to activate the back contact. Both the ZnTe to Cu ratio and the RTP activation temperature provide independent control over the device performance. We have investigated the influence of various RTP conditions to Cu activation and distribution. Current density-voltage, capacitance-voltage measurements along with device simulations were used to examine the device performance in terms of ZnTe to Cu ratio and rapid thermal activation temperature.

14 SOLAR ENERGY↗

Interfacial Modifiers for Enhanced Stability and Reduced Degradation of Cu(In,Ga)Se2 Devices

Transparent conductive oxide (TCO) degradation is a known failure mode in thin-film photovoltaic (PV) devices through mechanisms such as resistivity increase and delamination. Here we apply thin interfacial modifiers to aluminum-doped zinc oxide (AZO) to mitigate damp heat induced degradation of electrical performance. Additionally, we demonstrate that these modifiers can be applied to the AZO front contact of a Cu(In, Ga)Se2 device without significantly degrading the device performance, a promising step towards improving the lifetime performance.

14 SOLAR ENERGY↗

A Device-Independent Screening Technique for Rapidly Identifying Next Generation OPV Materials

In this paper, we introduce a methodology that enables rapid down selection of promising new OPV polymers, based on a device-independent screening metric that takes into account intrinsic charge generation and transport, as well as charge carrier lifetimes. As a demonstration of our method, we present a case study using a set of well-known high performance polymers based on the benzodithiophene (BDT) moiety: PTB7, PTB7-Th, PBDTTT-CT, and PBDTTPD. Compared to current device-optimization based methods, we are able to identify the champion material in less time, taking only hours rather than months and may even be able to identify promising candidate materials that have been abandoned for device optimization.

14 SOLAR ENERGY↗

Commissioning, Performance, and Effect of the Quench Current-Boosting Device on a Dedicated Superconducting Magnet

Superconducting magnet training is one of the accelerator related issues attracting attention due to significant operational costs and time budget associated to it. It is especially worrisome that magnets based on the “next-generation” Nb 3 Sn technology are affected by long training. While various efforts are underway to better understand and resolve the problem a parallel path could also be investigated, a path bypassing the issue. Following the concept of fast induced over-current during magnet powering, FNAL has developed an upgradable capacitor-based device to discharge through a superconducting magnet at quench detection or operator chosen time. The 0.4 F/1 kV device has been tested on a 1-m-long dipole-coil in a “mirror” magnet configuration and conclusive results on magnet training elimination have been observed. Here in this paper we discuss the main characteristics of the device, compare simulated response and actual performance, elaborate on test drivers and outcomes. Next steps and perspectives for future use are debated.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Characterization of Metamorphic GaAsP/Si Materials and Devices for Photovoltaic Applications

GaAsyP{sub 1-y} anion-sublattice compositionally graded buffers and device structures were grown directly on Si(100) substrates by way of a high-quality GaP integration layer, yielding GaAsP target layers having band gaps of photovoltaic interest (1.65-1.8 eV), free of antiphase domains/borders, stacking faults, and microtwins. GaAsyP{sub 1-y} growths on both Si and GaP substrates were compared via high-resolution X-ray diffractometry of the metamorphic buffers and deep-level transient spectroscopy (DLTS) of p{sup +}-n diodes that are lattice matched to the final buffer layer. Structural analysis indicates highly efficient epitaxial relaxation throughout the entire growth structure for both types of samples and suggests no significant difference in physical behavior between the two types of samples. DLTS measurements performed on GaAsP diodes fabricated on both Si and GaP substrates reveal the existence of identical sets of traps residing in the n-type GaAsP layers in both types of samples: a single majority carrier (electron) trap, which is located at EC - 0.18 eV, and a single minority carrier (hole) trap, which is located at EV + 0.71 eV. Prototype 1.75-eV GaAsP solar cell test devices grown on GaAsyP{sub 1-y}/Si buffers show good preliminary performance characteristics and offer great promise for future high-efficiency III-V photovoltaics integrated with Si substrates and devices.

14 SOLAR ENERGY↗

Electrically Driven Insulator–Metal Transition-Based Devices—Part I: The Electrothermal Model and Experimental Analysis for the DC Characteristics

We present a device model for the electrically driven insulator-to-metal transition (E-IMT) that captures the essential physics in E-IMT and can be used for physical device simulations and mixed-mode simulations of circuits containing IMT elements. Aspects of the model include the temperature-dependent resistivity, Joule heating, heat transport, and the spatial and dynamic coupling of the above phenomenon. We show that the model captures the dc and transient characteristics as measured by experiments. The model points out the existence of two critical transition voltages (V c ) under bidirectional sweep, the physical origin of this hysteresis, and correctly predicts the scaling of the critical voltage for transition V c with the device size. The models' effectiveness as a basis for developing a mixed-mode circuit simulator is shown via comparison with experimental data for a steep-swing hybrid-field-effect transistor.

Lin, Jianqiang↗