SEARCH · Search NASA

Results for “R PROCESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

All sources NASA NTRS DOE OSTI

NASA NTRS1993

Reflection-Type Oil-Film Skin-Friction Meter

Oil-film skin-friction meter for both flight and wind-tunnel applications uses internal reflection and is self-contained, compact unit. Contained in palm-sized housing, in which source of light, mirrors, and sensor mounted rigidly in alignment. Entire unit mounted rigidly under skin of aircraft or wind tunnel, eliminating any relative vibration between optical elements and skin of aircraft or wind tunnel. Meter primarily applicable to flight and wind-tunnel tests, also used in chemical-processing plants.

Bandyopadhyay, Promode R.↗

NASA NTRS1992

Strategic directions and mechanisms in technology transfer

An outline summarizing the Working Panel discussion related to strategic directions for technology transfer is presented. Specific topics addressed include measuring success, management of technology, innovation and experimentation in the tech transfer process, integration of tech transfer into R&D planning, institutionalization of tech transfer, and policy/legislative resources.

Mackin, Robert↗

NASA NTRS1993

An investigation of squeeze-cast alloy 718

Alloy 718 billets produced by the squeeze-cast process have been evaluated for use as potential replacements for propulsion engine components which are normally produced from forgings. Alloy 718 billets were produced using various processing conditions. Structural characterizations were performed on 'as-cast' billets. As-cast billets were then homogenized and solution treated and aged according to conventional heat-treatment practices for this alloy. Mechanical property evaluations were performed on heat-treated billets. As-cast macrostructures and microstructures varied with squeeze-cast processing parameters. Mechanical properties varied with squeeze-cast processing parameters and heat treatments. One billet exhibited a defect free, refined microstructure, with mechanical properties approaching those of wrought alloy 718 bar, confirming the feasibility of squeeze-casting alloy 718. However, further process optimization is required, and further structural and mechanical property improvements are expected with process optimization.

Gamwell, W. R.↗

NASA NTRS1920

The ferrosilicon process for the generation of hydrogen

Report describes the generation of hydrogen by the reaction between ferrosilicon, sodium hydroxide, and water. This method known as the ferrosilicon method is especially adapted for use in the military field because of the relatively small size and low cost of the generator required to produce hydrogen at a rapid rate, the small operating force required, and the fact that no power is used except the small amount required to operate the stirring and pumping machinery. These advantages make it possible to quickly generate sufficient hydrogen to fill a balloon with a generator which can be transported on a motor truck. This report gives a summary of the details of the ferrosilicon process and a critical examination of the means which are necessary in order to make the process successful.

Weaver, E R↗

NASA NTRS1994

Active-Pixel Cosmic-Ray Sensor

Cosmic-ray sensor comprises planar rectangular array of lateral bipolar npn floating-base transistors each of which defines pixel. Collector contacts of all transistors in each row connected to same X (column) line conductor; emitter contacts of all transistors in each column connected to same Y (row) line conductor; and current in each row and column line sensed by amplifier, output of which fed to signal-processing circuits.

Fossum, Eric R.↗

NASA NTRS1992

Programmability in AIPS++

AIPS++ is an Astronomical Information Processing System being designed and implemented by an international consortium of NRAO and six other radio astronomy institutions in Australia, India, the Netherlands, the United Kingdom, Canada, and the USA. AIPS++ is intended to replace the functionality of AIPS, to be more easily programmable, and will be implemented in C++ using object-oriented techniques. Programmability in AIPS++ is planned at three levels. The first level will be that of a command-line interpreter with characteristics similar to IDL and PV-Wave, but with an intensive set of operations appropriate to telescope data handling, image formation, and image processing. The third level will be in C++ with extensive use of class libraries for both basic operations and advanced applications. The third level will allow input and output of data between external FORTRAN programs and AIPS++ telescope and image databases. In addition to summarizing the above programmability characteristics, this talk will given an overview of the classes currently being designed for telescope data calibration and editing, image formation, and the 'toolkit' of mathematical 'objects' that will perform most of the processing in AIPS++.

Hjellming, R. M.↗

NASA NTRS1994

An avionics scenario and command model description for Space Generic Open Avionics Architecture (SGOAA)

This paper presents a description of a model for a space vehicle operational scenario and the commands for avionics. This model will be used in developing a dynamic architecture simulation model using the Statemate CASE tool for validation of the Space Generic Open Avionics Architecture (SGOAA). The SGOAA has been proposed as an avionics architecture standard to NASA through its Strategic Avionics Technology Working Group (SATWG) and has been accepted by the Society of Automotive Engineers (SAE) for conversion into an SAE Avionics Standard. This architecture was developed for the Flight Data Systems Division (FDSD) of the NASA Johnson Space Center (JSC) by the Lockheed Engineering and Sciences Company (LESC), Houston, Texas. This SGOAA includes a generic system architecture for the entities in spacecraft avionics, a generic processing external and internal hardware architecture, and a nine class model of interfaces. The SGOAA is both scalable and recursive and can be applied to any hierarchical level of hardware/software processing systems.

Stovall, John R.↗

NASA NTRS1993

Radial basis function neural networks applied to NASA SSME data

This paper presents a brief report on the application of Radial Basis Function Neural Networks (RBFNN) to the prediction of sensor values for fault detection and diagnosis of the Space Shuttle's Main Engines (SSME). The location of the Radial Basis Function (RBF) node centers was determined with a K-means clustering algorithm. A neighborhood operation about these center points was used to determine the variances of the individual processing notes.

Wheeler, Kevin R.↗

NASA NTRS1993

In situ measurements of the ClO/HCl ratio: Heterogeneous processing on sulfate aerosols and polar stratospheric clouds

Simultaneous in situ measurements of stratospheric ClO and HCl have been made for the first time, during numerous flights of the ER-2 aircraft covering latitudes 24-90 deg N from October 1991 through March 1992. The ClO/HCl ratio is identified as a key indicator of heterogeneous processing both outside and within the Arctic polar vortex. For ClO mixing ratios below about 120 pptv, remarkably constant ClO/HCl values of about 15% characterize the lower stratosphere. The observed values are significantly higher than those derived from a 2-D model using either gas phase photochemistry alone (2%), or including heterogeneous sulfate chemistry (5-10%). During the Arctic early spring, after conversion of HCl into reactive chlorine has taken place, the vortex edge is poorly defined by ClO levels. Loss of HCl and its slow recovery following low-temperature polar heterogeneous chemistry distinguishes HCl as a new and unique dynamical tracer of polar stratospheric clouds (PSC)-processed air.

Webster, C. R.↗

NASA NTRS1995

Technology Transfer

The objective of this summer's work was to attempt to enhance Technology Application Group (TAG) ability to measure the outcomes of its efforts to transfer NASA technology. By reviewing existing literature, by explaining the economic principles involved in evaluating the economic impact of technology transfer, and by investigating the LaRC processes our William & Mary team has been able to lead this important discussion. In reviewing the existing literature, we identified many of the metrics that are currently being used in the area of technology transfer. Learning about the LaRC technology transfer processes and the metrics currently used to track the transfer process enabled us to compare other R&D facilities to LaRC. We discuss and diagram impacts of technology transfer in the short run and the long run. Significantly, it serves as the basis for analysis and provides guidance in thinking about what the measurement objectives ought to be. By focusing on the SBIR Program, valuable information regarding the strengths and weaknesses of this LaRC program are to be gained. A survey was developed to ask probing questions regarding SBIR contractors' experience with the program. Specifically we are interested in finding out whether the SBIR Program is accomplishing its mission, if the SBIR companies are providing the needed innovations specified by NASA and to what extent those innovations have led to commercial success. We also developed a survey to ask COTR's, who are NASA employees acting as technical advisors to the SBIR contractors, the same type of questions, evaluating the successes and problems with the SBIR Program as they see it. This survey was developed to be implemented interactively on computer. It is our hope that the statistical and econometric studies that can be done on the data collected from all of these sources will provide insight regarding the direction to take in developing systematic evaluations of programs like the SBIR Program so that they can reach their maximum effectiveness.

Smith, Nanette R.↗

NASA NTRS1993

In Situ Measurements of the ClO/HCl Ratio: Heterogeneous Processing on Sulfate Aerosols and Polar Stratospheric Clouds

Simultaneous in situ measurements of stratospheric ClO and HCl have been made for the first time, during numerous flights of the ER-2 aircraft covering latitudes 24-90 deg. N from October 1991 through March 1992. The ClO/HCl ratio is identified as a key indicator of heterogeneous processing both outside and within the Arctic polar vortex. For ClO mixing ratios below about 120 pptv, remarkably constant ClO/HCl values of about 15% characterize the lower stratosphere. The observed values are significantly higher than those derived from a 2-D model using either gas phase photochemistry alone (2%), or including heterogeneous sulfate chemistry (5-10%). During the Arctic early spring, after conversion of HCl into reactive chlorine has taken place, the vortex edge is poorly defined by ClO levels. Loss of HCl and its slow recovery following low-temperature polar heterogeneous chemistry distinguishes HCl as a new and unique dynamical tracer of PSC-processed air.

Webster, C. R.↗

NASA NTRS1993

In Situ Measurements of the ClO/HCl Ratio: Heterogeneous Processing on Sulfate Aerosols and Polar Stratospheric Clouds

Webster, C. R.↗

NASA NTRS1996

BPSK Demodulation Using Digital Signal Processing

A digital communications signal is a sinusoidal waveform that is modified by a binary (digital) information signal. The sinusoidal waveform is called the carrier. The carrier may be modified in amplitude, frequency, phase, or a combination of these. In this project a binary phase shift keyed (BPSK) signal is the communication signal. In a BPSK signal the phase of the carrier is set to one of two states, 180 degrees apart, by a binary (i.e., 1 or 0) information signal. A digital signal is a sampled version of a "real world" time continuous signal. The digital signal is generated by sampling the continuous signal at discrete points in time. The rate at which the signal is sampled is called the sampling rate (f(s)). The device that performs this operation is called an analog-to-digital (A/D) converter or a digitizer. The digital signal is composed of the sequence of individual values of the sampled BPSK signal. Digital signal processing (DSP) is the modification of the digital signal by mathematical operations. A device that performs this processing is called a digital signal processor. After processing, the digital signal may then be converted back to an analog signal using a digital-to-analog (D/A) converter. The goal of this project is to develop a system that will recover the digital information from a BPSK signal using DSP techniques. The project is broken down into the following steps: (1) Development of the algorithms required to demodulate the BPSK signal; (2) Simulation of the system; and (3) Implementation a BPSK receiver using digital signal processing hardware.

Garcia, Thomas R.↗

NASA NTRS1998

Attitude Estimation Signal Processing: A First Report on Possible Algorithms and Their Utility

In this brief effort, time has been of the essence. The data had to be acquired from APL/Lincoln Labs, stored, and sorted out to obtain the pertinent streams. This has been a significant part of this effort and hardware and software problems have been addressed with the appropriate solutions to accomplish this part of the task. Passed this, some basic and important algorithms are utilized to improve the performance of the attitude estimation systems. These algorithms are an essential part of the signal processing for the attitude estimation problem as they are utilized to reduce the amount of the additive/multiplicative noise that in general may or may not change its structure and probability density function, pdf, in time. These algorithms are not currently utilized in the processing of the data, at least, we are not aware of their use in this attitude estimation problem. Some of these algorithms, like the variable thresholding, are new conjectures, but one would expect that someone somewhere must have utilized this kind of scheme before. The variable thresholding idea is a straightforward scheme to use in case of a slowly varying pdf, or statistical moments of the unwanted random process. The algorithms here are kept simple but yet effective for processing the data and removing the unwanted noise. For the most part, these algorithms can be arranged so that their consecutive and orderly execution would complement the preceding algorithm and improve the overall performance of the signal processing chain.

Riasati, Vahid R.↗

NASA NTRS1994

Intelligent Computational Systems. Opening Remarks: CFD Application Process Workshop

This discussion will include a short review of the challenges that must be overcome if computational physics technology is to have a larger impact on the design cycles of U.S. aerospace companies. Some of the potential solutions to these challenges may come from the information sciences fields. A few examples of potential computational physics/information sciences synergy will be presented, as motivation and inspiration for the Improving The CFD Applications Process Workshop.

VanDalsem, William R.↗

NASA NTRS2002

Meshless Local Petrov-Galerkin Method for Bending Problems

Recent literature shows extensive research work on meshless or element-free methods as alternatives to the versatile Finite Element Method. One such meshless method is the Meshless Local Petrov-Galerkin (MLPG) method. In this report, the method is developed for bending of beams - C1 problems. A generalized moving least squares (GMLS) interpolation is used to construct the trial functions, and spline and power weight functions are used as the test functions. The method is applied to problems for which exact solutions are available to evaluate its effectiveness. The accuracy of the method is demonstrated for problems with load discontinuities and continuous beam problems. A Petrov-Galerkin implementation of the method is shown to greatly reduce computational time and effort and is thus preferable over the previously developed Galerkin approach. The MLPG method for beam problems yields very accurate deflections and slopes and continuous moment and shear forces without the need for elaborate post-processing techniques.

Phillips, Dawn R.↗

NASA NTRS2003

Magnetic Flux Compression Experiments Using Plasma Armatures

Magnetic flux compression reaction chambers offer considerable promise for controlling the plasma flow associated with various micronuclear/chemical pulse propulsion and power schemes, primarily because they avoid thermalization with wall structures and permit multicycle operation modes. The major physical effects of concern are the diffusion of magnetic flux into the rapidly expanding plasma cloud and the development of Rayleigh-Taylor instabilities at the plasma surface, both of which can severely degrade reactor efficiency and lead to plasma-wall impact. A physical parameter of critical importance to these underlying magnetohydrodynamic (MHD) processes is the magnetic Reynolds number (R(sub m), the value of which depends upon the product of plasma electrical conductivity and velocity. Efficient flux compression requires R(sub m) less than 1, and a thorough understanding of MHD phenomena at high magnetic Reynolds numbers is essential to the reliable design and operation of practical reactors. As a means of improving this understanding, a simplified laboratory experiment has been constructed in which the plasma jet ejected from an ablative pulse plasma gun is used to investigate plasma armature interaction with magnetic fields. As a prelude to intensive study, exploratory experiments were carried out to quantify the magnetic Reynolds number characteristics of the plasma jet source. Jet velocity was deduced from time-of-flight measurements using optical probes, and electrical conductivity was measured using an inductive probing technique. Using air at 27-inHg vacuum, measured velocities approached 4.5 km/s and measured conductivities were in the range of 30 to 40 kS/m.

Turner, M. W.↗

NASA NTRS2001

Spatial scale of motion segmentation from speed cues

For the accurate perception of multiple, potentially overlapping, surfaces or objects, the visual system must distinguish different local motion vectors and selectively integrate similar motion vectors over space to segment the retinal image properly. We recently showed that large differences in speed are required to yield a percept of motion transparency. In the present study, to investigate the spatial scale of motion segmentation from speed cues alone, we measured the speed-segmentation threshold (the minimum speed difference required for 75% performance accuracy) for 'corrugated' random-dot patterns, i.e. patterns in which dots with two different speeds were alternately placed in adjacent bars of variable width. In a first experiment, we found that, at large bar widths, a smaller speed difference was required to segment and perceive the corrugated pattern of moving dots, while at small bar-widths, a larger speed difference was required to segment the two speeds and perceive two transparent surfaces of moving dots. Both the perceptual and segmentation performance transitions occurred at a bar width of around 0.4 degrees. In a second experiment, speed-segmentation thresholds were found to increase sharply when dots with different speeds were paired within a local pooling area. The critical pairing distance was about 0.2 degrees in the fovea and increased linearly with stimulus eccentricity. However, across the range of eccentricities tested (up to 15 degrees ), the critical pairing distance did not change much and remained close to the receptive field size of neurons within the primate primary visual cortex. In a third experiment, increasing dot density changed the relationship between speed-segmentation thresholds and bar width. Thresholds decreased for large bar widths, but increased for small bar widths. All of these results are well fit by a simple stochastic model, which estimates the probabilities of having identical or different motion vectors within a local pooling area whose size is the same as that of primate V1 neurons. Altogether, these results demonstrate that speed-based segmentation can function well, even at small spatial scales (i.e. high-spatial frequencies of spatial corrugation) and thereby emphasizes the critical role of a local pooling process early in the cortical motion-processing pathway.

NASA Discipline Neuroscience↗