Search NASA⌕ Search

SEARCH · Search NASA

Results for “SOUND VELOCITY - MEASUEMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

Fifty Years of Fluidic Injection for Jet Noise Reduction

The paper reviews 50 years of research investigating jet noise reduction through fluidic injection. Both aqueous and gaseous injection concepts for supersonic and subsonic jet exhausts are discussed. Aqueous injection reduces jet noise by reducing main jet temperature through evaporation and main jet velocity through momentum transfer between water droplets and the main jet. In the launch vehicle environment where large quantities of fluid do not have to be carried with the vehicle, water injection is very effective at reducing excess overpressures. For in-flight use, aqueous injection is problematic as most studies show that either large quantities of water or high injection pressures are required to achieve noise reduction. The most effective noise reduction injection systems require water pressures above 2000 kPa (290 psi) and water-to-mainjet mass flow rates above 10% to achieve overall sound pressure level reductions of roughly 6 dB in the peak jet noise direction. Injection at lower pressure (roughly 1034 kPa or 150 psi) has resulted in a 1.6 EPNdb reduction in effective perceived noise level. Gaseous injection reduces noise through jet plume modifications resulting from the introduction of streamwise vorticity in the main jet. In subsonic single-stream jets, air injection usually produces the largest overall sound pressure level reductions (roughly 2 dB) in the peak jet noise direction. In dual-stream jets, properly designed injection systems can reduce overall sound pressure levels and effective perceived noise levels but care must be taken to choose injector designs that limit sound pressure level increases at high frequencies. A reduction of 1.0 EPNdB has been achieved with injection into the fan and core streams. However, air injection into dual-stream subsonic jets has received little attention and the potential for noise reduction is uncertain at this time. For dual-stream supersonic jets, additional research needs to be conducted to determine if reductions can be achieved with injection pressures available from current aircraft engines. 1.

Henderson, Brenda↗

Trajectory Reconstruction of the ST-9 Sounding Rocket Experiment Using IMU and Landmark Data

This paper presents trajectory reconstruction of the ST-9 sounding rocket experiment using the onboard IMU data and descent imagery. The raw IMU accelerometer measurements are first converted into inertial acceleration and then used in trajectory integration. The descent images are pre-processed using a map-matching algorithm and unique landmarks for each image are created. Using the converted IMU data and descent images, the result from dead-reckoning and the kinematic-fix approaches are first compared with the GPS measurements. Then, both the IMU data and landmarks are processed together using a batch least-squares filter and the position, velocity, stochastic acceleration, and camera orientation of each image are estimated. The reconstructed trajectory is compared with the GPS data and the corresponding formal uncertainties are presented. The result shows that IMU data and descent images processed with a batch filter algorithm provide the trajectory accuracy required for pin-point landing.

Park, Ryan S.↗

Calibration and validation of the foundation for a multiphase strength model for tin

In this work, the Common Model of Multi-phase Strength and Equation of State (CMMP) model was applied to tin. Specifically, calibrations of the strength-specific elements of the CMMP foundation were developed with a combination of experiments and theory, and then the model was validated experimentally. The first element of the foundation is a multi-phase analytic treatment of the melt temperature and the shear modulus for the solid phases. These models were parameterized for each phase based on ab initio calculations using the software VASP (Vienna Ab initio Simulations Package) based on density functional theory. The shear modulus model for the ambient phase was validated with ultrasonic sound speed measurements as a function of pressure and temperature. The second element of the foundation is a viscoplastic strength model for the phase, upon which strength for inaccessible higher-pressure phases can be scaled as necessary. The stress–strain response of tin was measured at strain rates of 10 -3 to 3 x 10 3 s -1 and temperatures ranging from 87 to 373 K. The Preston–Tonks–Wallace (PTW) strength model was fit to that data using Bayesian model calibration. For validation, six forward and two reverse Taylor impact experiments were performed at different velocities to measure large plastic deformation of tin at strain rates up to ⁠10 5 s -1 . The PTW model accurately predicted the deformed shapes of the cylinders, with modest discrepancies attributed to the inability of PTW to capture the effects of twinning and dynamic recrystallization. Some material in the simulations of higher velocity Taylor cylinders reached the melting temperature, thus testing the multiphase model because of the presence of a second phase, the liquid. In simulations using a traditional modeling approach, the abrupt reduction of strength upon melt resulted in poor predictions of the deformed shape and non-physical temperatures. With CMMP, the most deformed material points evolved gradually to a mixed solid–liquid but never a fully liquid state, never fully lost strength, stayed at the melt temperature as the latent heat of fusion was absorbed, and predicted the deformed shape well.

36 MATERIALS SCIENCE↗

Theory of strong turbulence by renormalization

The hydrodynamical equations of turbulent motions are inhomogeneous and nonlinear in their inertia and force terms and will generate a hierarchy. A kinetic method was developed to transform the hydrodynamic equations into a master equation governing the velocity distribution, as a function of the time, the position and the velocity as an independent variable. The master equation presents the advantage of being homogeneous and having fewer nonlinear terms and is therefore simpler for the investigation of closure. After the closure by means of a cascade scaling procedure, the kinetic equation is derived and possesses a memory which represents the nonMarkovian character of turbulence. The kinetic equation is transformed back to the hydrodynamical form to yield an energy balance in the cascade form. Normal and anomalous transports are analyzed. The theory is described for incompressible, compressible and plasma turbulence. Applications of the method to problems relating to sound generation and the propagation of light in a nonfrozen turbulence are considered.

Tchen, C. M.↗

On the Lighthill relationship and sound generation from isotropic turbulence

In 1952, Lighthill developed a theory for determining the sound generated by a turbulent motion of a fluid. With some statistical assumptions, Proudman applied this theory to estimate the acoustic power of isotropic turbulence. Recently, Lighthill established a simple relationship that relates the fourth-order retarded time and space covariance of his stress tensor to the corresponding second-order covariance and the turbulent flatness factor, without making statistical assumptions for a homogeneous turbulence. Lilley revisited Proudman's work and applied the Lighthill relationship to evaluate directly the radiated acoustic power from isotropic turbulence. After choosing the time separation dependence in the two-point velocity time and space covariance based on the insights gained from direct numerical simulations, Lilley concluded that the Proudman constant is determined by the turbulent flatness factor and the second-order spatial velocity covariance. In order to estimate the Proudman constant at high Reynolds numbers, we analyzed a unique data set of measurements in a large wind tunnel and atmospheric surface layer that covers a range of the Taylor microscale based on Reynolds numbers 2.0 x 10(exp 3) less than or equal to R(sub lambda) less than or equal to 12.7 x 10(exp 3). Our measurements demonstrate that the Lighthill relationship is a good approximation, providing additional support to Lilley's approach. The flatness factor is found between 2.7 - 3.3 and the second order spatial velocity covariance is obtained. Based on these experimental data, the Proudman constant is estimated to be 0.68 - 3.68.

Zhou, YE↗

High-resolution sounding rocket observations of interstellar H2 lines toward Delta Scorpii

The results of observations made with an far-ultraviolet echelle spectrograph on interstellar absorption lines from the Lyman system of H2 toward the B0.5 IV star Delta Scorpii are reported. Equivalent widths are used to derive a total H2 column density of 2.8 x 10 to the 19th/sq cm, and a kinetic temperature of 62 K is inferred from the population ratio of the J = 0 and J = 1 rotational states. An excitation temperature of 210 K for J levels between two and five gives constraints on the H2 formation rate and the loud volume density and implies that the local ultraviolet radiation field is roughly six times as intense as the average value in the solar neighborhood. It is shown that there is little or no systematic velocity separation among the excited rotational levels.

Snow, Theodore P.↗

The effect of dust size distribution on quantum dust acoustic wave

Based on the quantum hydrodynamics theory, a proposed model for quantum dust acoustic waves (QDAWs) is presented including the dust size distribution (DSD) effect. A quantum version of Zakharov-Kuznetsov equation is derived adequate for describing QDAWs. Two different DSD functions are applied. The relevance of the wave velocity, amplitude, and width to the DSD is investigated numerically. The quantum effect changes only the soliton width. A brief conclusion is presented to the current findings and their relevance to astrophysics data is also discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of magnetic field on the wave dispersion relation in three-dimensional dusty plasma crystals

Three-dimensional plasma crystals under microgravity condition are investigated by taking into account an external magnetic field. The wave dispersion relations of dust lattice modes in the body centered cubic (bcc) and the face centered cubic (fcc) plasma crystals are obtained explicitly when the magnetic field is perpendicular to the wave motion. The wave dispersion relations of dust lattice modes in the bcc and fcc plasma crystals are calculated numerically when the magnetic field is in an arbitrary direction. The numerical results show that one longitudinal mode and two transverse modes are coupled due to the Lorentz force in the magnetic field. Moreover, three wave modes, i.e., the high frequency phonon mode, the low frequency phonon mode, and the optical mode, are obtained. The optical mode and at least one phonon mode are hybrid modes. When the magnetic field is neither parallel nor perpendicular to the primitive wave motion, all the three wave modes are hybrid modes and do not have any intersection points. It is also found that with increasing the magnetic field strength, the frequency of the optical mode increases and has a cutoff at the cyclotron frequency of the dust particles in the limit of long wavelength, and the mode mixings for both the optical mode and the high frequency phonon mode increase. The acoustic velocity of the low frequency phonon mode is zero. In addition, the acoustic velocity of the high frequency phonon mode depends on the angle of the magnetic field and the wave motion but does not depend on the magnetic field strength.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The exact calculation of quadrupole sources for some incompressible flows

This paper is concerned with the application of the acoustic analogy of Lighthill to the acoustic and aerodynamic problems associated with moving bodies. The Ffowcs Williams-Hawkings equation, which is an interpretation of the acoustic analogy for sound generation by moving bodies, manipulates the source terms into surface and volume sources. Quite often in practice the volume sources, or quadrupoles, are neglected for various reasons. Recently, Farassat, Long and others have attempted to use the FW-H equation with the quadrupole source and neglected to solve for the surface pressure on the body. The purpose of this paper is to examine the contribution of the quadrupole source to the acoustic pressure and body surface pressure for some problems for which the exact solution is known. The inviscid, incompressible, 2-D flow, calculated using the velocity potential, is used to calculate the individual contributions of the various surface and volume source terms in the FW-H equation. The relative importance of each of the sources is then assessed.

Brentner, Kenneth S.↗

Exact evaluation of the quadratic longitudinal response function for an unmagnetized Maxwellian plasma

The quadratic longitudinal response function describes the second-order nonlinear response of a plasma to electrostatic wave fields. An explicit expression for this function in the weak-turbulence regime requires the evaluation of velocity-space integrals involving the velocity distribution function and various resonant denominators. Previous calculations of the quadratic longitudinal response function were performed by approximating the resonant denominators to facilitate the integration. Here, we evaluate these integrals exactly for a non-relativistic collisionless unmagnetized isotropic Maxwellian plasma in terms of generalized plasma dispersion functions, and correct certain aspects of expressions previously derived for these functions. We show that in the appropriate limits the exact expression reduces to the approximate form used for interactions between two fast waves and one slow wave, such as the electrostatic decay of Langmuir waves into Langmuir waves and ion sound waves, and the scattering of Langmuir waves off thermal ions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Supercooled Liquid Water Detection Capabilities from Ka-Band Doppler Profiling Radars: Moment-Based Algorithm Formulation and Assessment

The occurrence of supercooled liquid water in mixed-phase cloud (MPC) affects their cloud microphysical and radiative properties. The prevalence of MPCs in the mid- and high latitudes translates these effects to significant contributions to Earth’s radiative balance and hydrological cycle. The current study develops and assesses a radar-only, moment-based phase partition technique for the demarcation of supercooled liquid water volumes in arctic, MPC conditions. The study utilizes observations from the Ka band profiling radar, the collocated high spectral resolution lidar, and ambient temperature profiles from radio sounding deployments following a statistical analysis of 5.5 years of data (January 2014–May 2019) from the Atmospheric Radiation Measurement observatory at the North Slope of Alaska. The ice/liquid phase partition occurs via a per-pixel, neighborhood-dependent algorithm based on the premise that the partitioning can be deduced by examining the mean values of locally sampled probability distributions of radar-based observables and then compare those against the means of climatologically derived, per-phase probability distributions. Analyzed radar observables include linear depolarization ratio (LDR), spectral width, and vertical gradients of reflectivity factor and radial velocity corrected for vertical air motion. Results highlight that the optimal supercooled liquid water detection skill levels are realized for the radar variable combination of spectral width and reflectivity vertical gradient, suggesting that radar-based polarimetry, in the absence of full LDR spectra, is not as critical as Doppler capabilities. The cloud phase masking technique is proven particularly reliable when applied to cloud tops with an Equitable Threat Score (ETS) of 65%; the detection of embedded supercooled layers remains much more uncertain (ETS = 27%).

54 ENVIRONMENTAL SCIENCES↗

Calibration and validation of the foundation for a multiphase strength model for tin

In this work, the Common Model of Multi-phase Strength and Equation of State (CMMP) model was applied to tin. Specifically, calibrations of the strength-specific elements of the CMMP foundation were developed with a combination of experiments and theory, and then the model was validated experimentally. The first element of the foundation is a 10 multi-phase analytic treatment of the melt temperature and the shear modulus for the solid phases. These models were parameterized for each phase based on ab initio calculations using the software VASP (Vienna Ab initio Simulations Package) based on density functional theory (DFT). The shear modulus model for the ambient β phase was validated with ultrasonic sound speed measurements as a function of pressure and temperature. The second element of the foundation is a viscoplastic strength model for the β phase, upon which strength for inaccessible higher-pressure phases can be scaled as necessary. The stress-strain response of tin was measured at strain rates of 10 -3 to 3 x 10 3 s -1 and temperatures ranging from 87 to 373 K. The Preston-Tonks-Wallace (PTW) strength model was fit to that data using Bayesian model calibration. For validation, six forward and two reverse Taylor impact experiments were performed at different velocities to measure large plastic deformation of tin at strain rates up to 10 5 s -1 . The PTW model accurately predicted the deformed shapes of the cylinders, with modest discrepancies attributed to the inability 20 of PTW to capture the effects of twinning and dynamic recrystallization. Some material in the simulations of higher velocity Taylor cylinders reached the melting temperature, thus testing the multiphase model because of the presence of a second phase, the liquid. In simulations using a traditional modeling approach, the abrupt reduction of strength upon melt resulted in poor predictions of the deformed shape and non-physical temperatures. With CMMP, the most deformed material points evolved gradually to a mixed solid-liquid but never fully liquid state, never fully lost strength, 25 stayed at the melt temperature as the latent heat of fusion was absorbed, and predicted the deformed shape well.

36 MATERIALS SCIENCE↗

Large gyro-orbit model of ion velocity distribution in plasma near a wall in a grazing-angle magnetic field

A model is presented for the ion distribution function in a plasma at a solid target with a magnetic field $\boldsymbol {B}$ inclined at a small angle, $\alpha \ll 1$ (in radians), to the target. Adiabatic electrons are assumed, requiring $\alpha \gg \sqrt {Zm_{e}/m_{i}}$ , where $m_{e}$ and $m_{i}$ are the electron and ion mass, respectively, and $Z$ is the charge state of the ion. An electric field $\boldsymbol {E}$ is present to repel electrons, and so the characteristic size of the electrostatic potential $\phi$ is set by the electron temperature $T_{e}$ , $e\phi \sim T_{e}$ , where $e$ is the proton charge. An asymptotic scale separation between the Debye length $\lambda _{D} = \sqrt {\epsilon _0 T_{{e}} / e^{2} n_{{e}} }$ , the ion sound gyro-radius $\rho _{s} = \sqrt { m_{i} ( ZT_{e} + T_{i} ) } / (ZeB)$ and the size of the collisional region $d_{c} = \alpha \lambda _{\textrm {mfp}}$ is assumed, $\lambda _{D} \ll \rho _{s} \ll d_{c}$ . Here $\epsilon _0$ is the permittivity of free space, $n_{e}$ is the electron density, $T_{i}$ is the ion temperature, $B= |\boldsymbol {B}|$ and $\lambda _{\textrm {mfp}}$ is the collisional mean free path of an ion. The form of the ion distribution function is assumed at distances $x$ from the wall such that $\rho _{s} \ll x \ll d_{c}$ , that is, collisions are not treated. A self-consistent solution of the electrostatic potential for $x \sim \rho _{s}$ is required to solve for the quasi-periodic ion trajectories and for the ion distribution function at the target. The large gyro-orbit model presented here allows to bypass the numerical solution of $\phi (x)$ and results in an analytical expression for the ion distribution function at the target. It assumes that $\tau =T_{i}/(ZT_{e})\gg 1$ , and ignores the electric force on the quasi-periodic ion trajectory until close to the target. For $\tau \gtrsim 1$ , the model provides an extremely fast approximation to energy–angle distributions of ions at the target. These can be used to make sputtering predictions.

Physics↗

Electronic and Vibrational Properties of LiBO{sub 2} Crystals

On the basis of the density functional theory using the CRYSTAL code, electronic and vibrational properties of lithium metaborate in the monoclinic and tetragonal phases are studied. The band spectra, elastic moduli, long-wave vibrational frequencies at the point Г, dynamic charges, and acoustic velocities are calculated for both phases. The influence of structural features and short-range order in trigonal BO{sub 3}- and tetragonal BO{sub 4}- groups on the significant difference in physical properties in the low-temperature and high-temperature phases of LiBO{sub 2} crystal is established.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Large sounding rockets as a base for probing the distant magnetosphere

The Echo program's use of large sounding rockets to inject electron beams into the outer trapping region where the earth's plasma sheet interacts with the inner magnetosphere is discussed. The beams pass through the plasma sheet and the trapping region, reflect at the southern hemisphere conjugate point and return to the vicinity of the rocket where they are detected and analyzed for acceleration and diffusion processes which may also be responsible for the radiation belts. The motion of electron beams in the magnetosphere is discussed from the standpoint of single particle motion, and the trajectories of electrons injected with known energy, known angle between the electron velocity vector and the local magnetic field vector, and known position are examined. The interaction between the rocket motion and the electron drift motion is described, and the advantages and drawbacks of beam detection by optical methods and by throwaway detectors are compared. Planned Echo experiments using the Space Shuttle are discussed

Winckler, J. R.↗

Kinematic and precipitation structure of a small, long-lived mesoscale convective system

A comprehensive analysis using conventional single Doppler radar analyses, analysis of multiparameter (CP-2) data, network sounding and surface data, and GOES satellite data is presented to characterize the internal kinematic and precipitation structure of a small, long-lived mesoscale convective system. The data pertain to the Cooperative Huntsville Meteorological experiment conducted over northern Alabama and central Tennessee during June and July of 1986. The mesoscale convective system pulsations visible in the IR patterns were associated with the development of closely interacting aggregates of convective elements. The aggregates were about 20 km in diameter, attained echo tops of about 13 km, and were dominated by a single relatively intense convective element. The measured difference in radial velocity across the upper portion of these elements was about 20 m/s over a distance of about 10 km.

Knupp, Kevin R.↗

Explosions of infalling comets in Jupiter's atmosphere

In view of the expected collision of comet Shoemaker-Levy 9 (1993e) with Jupiter in 1994 July, we calculate basic properties of the initial interaction for a simplified Jovian atmosphere. The comet is expected to impact Jupiter at 60 km/sec and at an angle of 45 deg to the zenith. The shock wave generated by the bolide should be optically thick once it has penetrated to an atmospheric density approximately 10(exp -6) gr/cm(exp 3), and we calculate the post-shock conditions assuming local thermodynamic equilibrium (LTE) for shock velocities v(sub sh) in the range 10 to 60 km/sec and preshock densities rho(sub a) = 10(exp -6) to 10(exp -2) gr/cm(exp 3). Our shock calculations include molecular hydrogen, atomic hydrogen, ionized hydrogen, neutral helium, and singly ionized helium. Even at the highest shock velocity, the gas is only partially ionized and the postshock temperature rises with preshock density in order to maintain the ionization. The value of the effective shock adiabatic index gamma(sub sh) varies from 1.17 (at low v(sub sh) and rho(sub a) to 1.40 (at high v(sub sh) and rho(sub a). The ablation rate is limited by the radiative flux that reaches the bolide surface. We argue that the ablated gas does not efficiently transfer its kinetic energy to the atmosphere, and it ultimately slows in a similar fashion to the comet material. As the bolide initially falls through the atmosphere, the character of the shock emission changes. At rho(sub a) approximately 10(exp -8) gr/cm (exp 3), the gas is optically thin and we expect line emission; in the optical spectrum, Balmer emission is expected from the shocked atmosphere and low-ionization metal lines from ablated cometary material. At rho(sub a) approximately 10(exp -6) gr/m(exp 3), the shocked gas is optically thick and the shock front near the bolide produces a blackbody spectrum. The temperature is favorable for ultraviolet (1000 to 3000 A) emission and the luminosity may be approximately 5 x 10(exp 23) ergs/sec for approximately 0.6 sec for a bolide 1 km in radius. At rho(sub a) approximately 10(exp -4) gr/cm(exp 3), the bolide has passed below the ultraviolet photosphere. The shock front emits considerable ionizing radiation, but it is absorbed in a narrow preshock region. The bolometric correction for the optical luminosity is large and we expect a 3000 to 8000 A luminosity of approximately 3 x 10(exp 23) ergs/sec for approximately 1 sec. The optical emission is strongly peaked in the vicinity of the bolide. The bolide does have a somewhat less luminous, optically thick trail extending greater than or equal to 10 km, but the radiation is characterized by a temperature of 4000 to 5000 K. From the fragmentation model of Chyba, Thomas, & Zahnle (1993), the bolide deposits most of its kinetic energy at rho(sub a) approximately 10(exp -3) gr/cm(exp 3) and this is the effective explosion site. The shock wave from such an explosion can move up about one density scale height. We examine the breakout of the shock front from the Jovian atmosphere and find that the shock acceleration in the decreasing density region is slow, so that the energy flux in the shock front is small. Higher velocities might be generated by shock acceleration along the channel left by the bolide if the shock motion can occur before the channel closes off as a result of radiative cooling. Hot gas created by the explosion ultimately rises due to buoyancy on a timescale of a minute. The luminosity is highest when the bubble first rises into the optically thin part of the atmosphere and may be approximately 1 x 10(exp 25) ergs/sec in the near-infrared. Roughly 1% of the initial bolide energy may be radiated in this way; the rest of the energy is lost to sound waves from the initial explosion and to work done by the bubble on the surrounding atmosphere.

Chevalier, Roger A.↗

A Study of Intermittent Turbulence in Stable Arctic Boundary Layers

Abstract Polar boundary layers are difficult to model due to the existence of intermittent turbulence within stable layers. Here we present a case study evaluation of coherent structures in a stable boundary layer observed during a series of flights with an uncrewed aircraft system (DataHawk2) on 19 October 2016 at Oliktok Point, Alaska as part of the ERASMUS (Evaluation of Routine Atmospheric Sounding Measurements using Unmanned Systems) field campaign. During a sequence of five flights over a nine-hour period, 57 profiles of atmospheric properties (0–400 m a.g.l) were collected. Turbulence was identified using derived Richardson Number, temperature structure function parameter, and turbulence kinetic energy dissipation. Throughout all flights on this strongly stable day, intermittent turbulence was observed. These turbulent layers showed well-mixed potential temperature profiles embedded within otherwise stable potential temperature profiles; often resulting in a characteristic staircase pattern. Turbulent layers ranged from 1 to 30 m deep, with most individual layers being 1–2 m deep. Vertical propagation velocities of layers in the lower atmosphere were on the order of a few cm s −1 , typical of non-convective environments. In different regions of the profile, turbulence was driven by a different balance of buoyancy and shear forces, with turbulence in the near surface environment driven by strong shear forces overcoming strong resistance to buoyancy, while turbulence in elevated layers characterized by weaker shear forces overcoming weaker resistance to buoyancy. We discuss the potential of such datasets for improving subgrid parameterizations of small-scale turbulence embedded within stable boundary layers.

54 ENVIRONMENTAL SCIENCES↗