Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS - SWEEPBACK”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

Transonic-flutter Investigation of Wings Attached to Two Low-acceleration Rocket-propelled Vehicles

Two low-acceleration transonic-flutter vehicles were launched and flown. The first carried two test wings, one of which fluttered at M = 0.92 at a frequency of 61.4 cycles per second. The reference flutter speed determined from two-dimensional theory for an unswept wing in incompressible flow is conservative when compared to the experimental flutter speed. The second vehicle carried two test wings, one of which failed at M = 0.71 because of low-frequency divergent oscillation. Since this failure was not caused by conventional flexure-torsion flutter, no comparison with a reference flutter speed can be made.

MISSILES, SPECIFIC TYPES↗

Calculation of wing spars of variable cross-section and linear load

The calculation of wing spars of constant cross-section and load has been thoroughly treated by a large number of authors. Such is not the case,however, regarding the calculation of wing spars whose section and linear load diminish toward the ends, as in wings of trapezoidal contour and decreasing section.

SPARS↗

Experiments with a wing from which the boundary layer is removed by pressure or suction

With an unsymmetrical wing and a rotating Magnus cylinder, the lift is produced by the superposition of parallel and circulatory flows. An explanation of the circulatory flow is furnished by the boundary-layer theory of Prandtl and the consequent vortex formation. According to this explanation, it must evidently be possible to increase the circulation either by increasing the size of the stronger (lower) vortex or by decreasing the size of the weaker (upper) vortex. In this sense, according to Professor H. Zickendraht, we have a new type of wing from which the boundary layer is removed by forcing air out or sucking it in through openings in the upper surface of the wing near its trailing edge.

VORTICES - WINGS↗

Flight Investigation of Wing-gun Fairings on a Fighter Type Airplane

Description is given of flight tests conducted on gun fairings, designed to correct the detrimental effects of the projecting and submerged wing guns on an F4F-3 fighter. It was found that the installation of unfaired guns on a clean wing resulted in a premature stall that increased the stalling speed in the carrier-approach and landing conditions of flight by suitably fairing the guns, it was possible to reduce the stalling speeds to values approaching very nearly the clean-wing values.

LOOPING - GROUND↗

Comparison of Computational Predictions of the Mach 0.80 Transonic Truss-Braced Wing Configuration with Experimental Data

The NASA Langley and Ames Research Centers have teamed together for comparisons of computational predictions of the Boeing Mach 0.80Transonic Truss-Braced Wing (TTBW) configuration with a high-speed experimental dataset. The Mach 0.80 TTBW vehicle is a high wing, high aspect ratio configuration, designed for a high lift-to-drag ratio. System studies have predicted significant fuel burn and emissions benefits with the TTBW technology moving toward meeting NASA Subsonic Transport Systems-Level-Metrics. A 4.5% scale Mach 0.80 design TTBW model was recently tested at the NASA Ames Research Center 11-by 11-Foot Transonic Wind Tunnel(11-Ft TWT),providing a valuable dataset to validate computational tools and investigate best practices as risk reduction efforts continue for the development of the advanced TTBW vehicle. The NASA Computational Fluid Dynamics (CFD) team has computed free-air flow solutions on the Mach 0.80 design flight configuration and two wind tunnel configuration variants using the USM3D and LAVA flow solvers. Accurate modeling of the configuration tested in the wind tunnel environment is critical to validating the CFD tools, thus the team has included the internal cavity region and sting in their modeling of the configuration, similar to that tested in the 11-Ft TWT. Overall, the CFD simulations compared well and show similar trends as the corrected experimental data for lift and drag polars. The CFD predicted lift curve is shifted in angle of attack from what was observed in the experiment. The shift in lift also was seen in the pitching moment comparison plots. CFD solutions were computed at constant CL test point values and showed overall very good agreement when comparing constant spanwise cuts of pressure coefficient data on the wing and strut with experimental data. CFD cavity corrections were also investigated using the 11-Ft TWT cavity correction method, similar to that used to correct the wind tunnel data. Results showed some improvement in pitching moment coefficient predictions, and an increase in drag, shifting the data to the right in drag polars, further from the experimental data at lower lift conditions, good agreement near the design CL, and slight improvement at the higher lift conditions.

Transonic Truss-Braced Wing↗

Large-Drop Ice Accretion Test Results for a Large Scale Swept Wing Model

In-flight icing is an important consideration that affects aircraft design, performance and safety. Newer regulations combined with increasing demand to reduce fuel burn, emissions and noise are driving a need for improvements in icing simulation capability. To that end, this paper presents the results of ice accretion testing conducted in the NASA Icing Research Tunnel on a large swept wing section typical of a modern commercial transport. The model was based upon a section of the Common Research Model wing at the 64% semispan station with a streamwise chord length of 136 in. The test conditions were developed with an icing scaling analysis to generate similar conditions for a small MVD = 25 μm and a large MVD = 110 μm. A series of tests were conducted over a range of total temperature from -23.8 ˚C to -1.4 ˚C with all other conditions held constant. The results for the small MVD cloud conditions were consistent with previous work and showed the changing ice morphology from rime ice at colder temperatures to highly 3D scallop ice in the range of -8.7 ˚C to -3.8 ˚C. The results for the large MVD cloud conditions exhibited some differences in the ice accretion morphology from the small MVD conditions. Scallop-like ice features were observed at total temperature of -3.8˚C. The large MVD ice accretion at lower temperatures tended to be smoother than the corresponding ice accretion for small MVD. The thickness of the main ice shape tended to be larger for the small MVD conditions compared to the corresponding large MVD ice shape while the latter had more ice farther downstream. The measured ice mass was approximately equal between the corresponding small and large MVD ice shapes up to a freezing fraction of 0.6. For higher freezing fraction, the large MVD ice shapes weighed more. Cloud MVD variation from 50 μm to 230 μm while holding the scaling parameters constant resulted in very minor differences in the ice shapes, mostly in the upper and lower surface chordwise extents. Ice volume was computed from 3D scan data and used to calculate a ratio of ice mass to volume. The resulting values were in the range of 240 to 455 Kg/m3. While this is consistent with analogous values previously reported in the literature, more data are needed to determine a specific trend in this ratio as a function of freezing fraction and the corresponding governing physical phenomena. This work has resulted in a significant experimental database of ice accretion for small and large MVD conditions applicable to large-scale swept wings.

Icing↗

Large-Drop Ice Accretion Test Results for a Large Scale Swept Wing Section

In-flight icing is an important consideration that affects aircraft design, performance and safety. Newer regulations combined with increasing demand to reduce fuel burn, emissions and noise are driving a need for improvements in icing simulation capability. To that end, this paper presents the results of ice accretion testing conducted in the NASA Icing Research Tunnel on a large swept wing typical of a modern commercial transport. The model was based upon a section of the Common Research Model wing at the 64% semispan station with a streamwise chord length of 136 in. The test conditions were developed with an icing scaling analysis to generate similar conditions for a small MVD = 25 μm and a large MVD = 110 μm. A series of tests were conducted over a range of total temperature from -23.8 ˚C to -1.4 ˚C with all other conditions held constant. The results for the small MVD cloud conditions were consistent with previous work and showed the changing ice morphology from rime ice at colder temperatures to highly 3D scallop ice in the range of -8.7 ˚C to -3.8 ˚C. The results for the large MVD cloud conditions exhibited some differences in the ice accretion morphology. Scallop-like ice features were observed at total temperature of -3.8˚C. The large MVD ice accretion at lower temperatures tended to be smoother than the corresponding ice accretion for small MVD. The thickness of the main ice shape tended to be larger for the small MVD conditions compared to the corresponding large MVD ice shape while the latter had more ice farther downstream. The measured ice mass was approximately equal between the corresponding small and large MVD ice shapes up to a freezing fraction of 0.6. For higher freezing fraction, the large MVD ice shapes weighed more. Cloud MVD variation from 50 μm to 230 μm while holding the scaling parameters constant resulted in very minor differences in the ice shapes, mostly in the upper and lower surface chordwise extents. Ice volume was computed from 3D scan data and used to calculate a ratio of ice mass to volume. The resulting values were in the range of 240 to 455 Kg/m3. While this is consistent with analogous values previously reported in the literature, more data are needed to determine a specific trend in this ratio as a function of freezing fraction and the corresponding governing physical phenomena. This work has resulted in a significant experimental database of ice accretion for small and large MVD conditions applicable to large-scale swept wings.

Icing↗

System Noise Technology Roadmaps for a Transonic Truss-Braced Wing and Peer Conventional Configuration

A system noise assessment is performed for a Boeing-designed Transonic Truss-Braced Wing, resized using NASA tools in order to estimate the performance of the configuration relative to NASA noise goals. For comparison, a conventional configuration with comparable mission requirements, technology assumptions, and design assumptions is also assessed. Following the baseline noise assessments, a noise reduction technology roadmap is developed from technologies expected to mature to an appropriate technology readiness level by the targeted entry into service date. Noise prediction of both baseline configurations shows a 4.7 EPNdB cumulative certification advantage for the Transonic Truss-Braced Wing. Both configurations fall short of the mid term NASA noise goal, even with application of the noise reduction technologies in the roadmap. The roadmap provides 7.3 EPNdB of noise reduction for the conventional configuration and 7.8 EPNdB for the Transonic Truss-Braced Wing.

system noise assessment↗

Flow Physics Study of Sweeping Jet Actuation on a NACA 0015 Swept Wing Configuration

Preliminary results from a recently completed active flow control (AFC) experiment on a 30 deg swept, semispan wing are presented. The constant chord NACA 0015 wing is configured with sweeping jet actuators at the flap shoulder to study the effects of excitation introduced into a separated, three-dimensional flowfield. The research is aimed at developing efficient active flow control approaches for swept wing configurations. Oil and tuft flow visualization data, steady and unsteady pressure data, particle image velocimetry (PIV), oil flow interferometry (OFI), and force and moment data are used to compare the flowfields with and without AFC. The parameters that were varied include freestream velocity, actuator momentum coefficient, and flap deflection angle.

active flow control↗

Aeroacoustic Computations of a Transonic Truss-Braced Wing Aircraft: Part 2 – Acoustic Signature and Noise Source Identification

High-fidelity, time-dependent simulations of a Boeing-designed, transonic, truss-braced-wing aircraft in cruise (clean) and landing configurations are leveraged to generate synthetic microphone-phased-array data for airframe noise prediction and assessment. These data sets are used to compute source localization (beamform) maps to determine the location and strength of primary and secondary airframe noise sources associated with this unique configuration. The synthetic phased-array implementation mimics the setup of a flight test. As this study is ongoing, preliminary integrated far-field spectra for the cruise configuration obtained at multiple spatial resolutions revealed significant tonal content that lacked convergence with increased resolution. The origin of several of these tones and their unusual convergence behavior was traced to the larger-than-normal trailing-edge thickness of the “as-tested” cruise model being simulated. Reducing the trailing-edge thickness to more realistic values eliminated most of the tones at low to moderate frequencies and improved spectrum convergence significantly. Applying lessons learned from the cruise simulations, several modifications to the geometry of the landing configuration were made and are described in this work. Results from permeable and solid Ffowcs-Williams and Hawkings surfaces at two different spatial resolutions (coarse and medium) are used to illustrate the major noise sources and determine convergence of the CLEAN integrated noise levels for the entire aircraft as well as major subcomponents. We demonstrate that the low-frequency content of the far-field spectrum is dominated by noise generated from the main landing gear, while the medium- and high-frequency content is dominated by the wing-leading-edge Krueger flaps. Since analysis of the acoustic maps for the landing configuration revealed several clusters of multiple sources along the wing leading edge, “high resolution” processing of the array data was used to distinguish more accurately the locations of sources.

Transonic Truss-Braced Wing↗

Experimental and Calculated Characteristics of Several NACA 44-series Wings with Aspect Ratios of 8, 10, and 12 and Taper Ratios of 2.5 and 3.5

The aerodynamic characteristics of seven unswept tapered wings were determined by calculation from two-dimensional data and by wind-tunnel tests in order to demonstrate the accuracy of the calculations and to show some of the effects of aspect ratio, taper ratio, and root thickness-chord ratio. The characteristics were calculated by the usual application of the lifting-line theory which assumes linear section lift curves and also by an application of the theory which allows the use of nonlinear lift curves. A correction to the lift for the effect of chord was made by using the Jones edge-velocity factor. The wings had aspect ratios of 8, 10, and 12, taper ratios of 2.5 and 3.5, and NACA 44-series airfoils.

WINGS, TAPERED - CHARACTERISTICS↗

Ground Effects on the Longitudinal Characteristics of Two Models with Wings Having Low Aspect Ratio and Pointed Tips

Wind-tunnel tests were conducted to determine the ground effects on a tailless model with a wing of aspect ratio 2 and infinite taper, and on a tailed model with a triangular wing of aspect ratio 3, with flaps. Control-surface hinge moments were measured on the tailless model. The results are compared with the predictions of the theory of Tani, et al.

CONTROLS, FLAP-TYPE - COMPLETE WINGS↗

Longitudinal-stability Investigation of High-lift and Stall-control Devices on a 52 Degree Sweptback Wing with and Without Fuselage and Horizontal Tail at a Reynolds Number of 6.8 x 10(exp 6).

Contains low-speed longitudinal stability characteristics of a 52 degree sweptback wing of aspect ratio 2.88, taper ratio 0.625, and NACA 64 (sub 1)-112 airfoil sections normal to the 0.282-chord line, in combination with split flaps, leading-edge flaps, and upper-surface fences. Low-wing and midwing-fuselage aerodynamic characteristics are presented with and without a horizontal tail at various vertical locations. Tests were conducted at a Reynolds number of 6.8 x 10(exp 6).

STABILITY, LONGITUDINAL - STATIC↗

A correlation by means of transonic similarity rules of the experimentally determined characteristics of 18 cambered wings of rectangular plan form

The effects of one type of camber on the aerodynamic characteristics of rectangular wings at high subsonic and transonic speeds have been studied by applying the transonic similarity rules to the correlation of experimental data for a series of 18 cambered wings having NACA 63A2XX and 63A4XX sections, aspect ratios from 1 to 4, and thicknesses from 4 to 8 percent. The data were obtained by use of a transonic bump over a Mach number range of 0.6 to 1.1.

PROFILES - COMPLETE WINGS↗

Approximate relations and charts for low-speed stability derivatives of swept wings

Contains derivations, based on a simplified theory, of approximate relations for low-speed stability derivatives of swept wings. Method accounts for the effects and, in most cases, taper ratio. Charts, based on the derived relations, are presented for the stability derivatives of untapered swept wings. Calculated values of the derivatives are compared with experimental results.

THEORIES - WINGS SWEPTBACK & SWEPTFORWARD↗

Drag Interference Between a Pointed Cylindrical Body and Triangular Wings of Various Aspect Ratios at Mach Numbers of 1.50 and 2.02

The drag of a body alone, six triangular wings of various aspect ratios, and the combinations were measured at Mach numbers of 1.50 and 2.02 at a Reynolds number of 5.5 million (based on the body length). The experimental drag-interference results were in accordance with calculations based on NACA RM A9E19, 1949, with skin-friction effects taken into account, the interference effect being principally the result of fixing transition on the body by adding a wing.

BODIES↗

An Investigation of the Low-speed Static Stability Characteristics of Complete Models Having Sweptback and Sweptforward Wings

An investigation has been conducted in the Langley 300 MPH 7- by 10-foot tunnel to determine the static stability characteristics at low speeds of complete models with various swept wings so that comparisons might be made with available theoretical and empirical methods of predicting the stability characteristics. Longitudinal and lateral stability characteristics, flaps up and down, were obtained for models having 0 degree, 15 degrees, 30 degrees, and 45 degrees sweptforward and sweptback wings.

SWEEP - COMPLETE WINGS↗

An Investigation of Aileron Oscillations at Transonic Speeds on NACA 23012 and NACA 65-212 Airfoils by the Wing-flow Method

An investigation is being conducted to determine the feasibility of studying aileron buzz by means of the wing-flow method. Two semispan models which had an aspect ratio of 6 and a taper ratio of 2 with quarter-chord half-span mass-balanced ailerons have been used. One had an NACA 23012 airfoil section and the second, an NACA 65-212 airfoil section. The ailerons on both models were subject to buzz over a small range of Mach number near 0.9. Data obtained by wing-flow testing agreed reasonably well with full-scale flight results.

MACH NUMBER EFFECTS - COMPLETE WINGS↗