Search NASA⌕ Search

SEARCH · Search NASA

Results for “diffusion length”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Self Induced Buoyant Blow Off in Upward Flame Spread on Thin Solid Fuels

Upward flame spread experiments were conducted on a thin fabric cloth consisting of 75% cotton and 25% fiberglass. The sample is sandwiched symmetrically with stainless steel plates with the exposed width varying between 2 to 8.8 cm from test to test and >1.5m tall. The bottom edge was ignited resulting in a symmetric two sided flame. For the narrower samples (. 5cm), two sided flame growth would proceed until reaching some limiting value (15-30 cm depending on sample width). Fluctuation or instability of the flame base on one side would initially become visible and then the flame base would retreat downstream and cause extinguishment on one side. Detailed examination of the still images shows that the fuel continues to vaporize from the extinguished side due to the thermally thin nature of the fuel. But, due to the remaining inert fiberglass mesh, which acts as a flashback arrestor, the extinguished side was not able to be reignited by the remaining flame. The remaining flame would then shrink in length due to the reduced heat transfer to the solid to a shorter length. The one-sided flame will spread stably with a constant speed and a constant flame length to the end of the sample. A constant length flame implies that the pyrolysis front and the burnt out fronts move at the same speed. For the wider samples (. 7cm), no one-sided extinction is observed. Two-sided flames spread all the way to the top of the sample. For these wider widths, the flames are still growing and have not reached their limiting length if it exists. Care was taken to minimize the amount of non-symmetries in the experimental configuration. Repeated tests show that blow-off can occur on either side of the sample. The flame growth is observed to be very symmetric during the growth phase and grew to significant length (>10cm) before extinction of the flame on one side. Our proposed explanation of this unusual phenomenon (i.e. stronger two ]sided flame cannot exist but weaker one-sided flame can) is as follows: The observed one-sided extinction is a blow- off induced by buoyant entrainment. It is known that the flammable diffusion flame regime is bounded by quenching and blow ]off limits when varying incoming air velocity. The narrowest samples tested (between 2 and 5 cm) begin within the flammable range, but as the flame grows, the buoyancy driven air velocity increases at the neighborhood of the flame base. The initially stable flame crosses the extinguishment boundary resulting in a flame blow-off. When one-side of the flame extinguishes, the remaining side shrinks due to the reduced heat transfer to the solid. This reduces the induced velocity and the flame becomes stable. It is proposed that this may have implications to upward flame growth beyond this experiment.

Johnston, Michael C.↗
DOE OSTI2015

Surface roughness scattering of electrons in bulk mosfets

Surface-roughness scattering of electrons at the Si-SiO 2 interface is a very important consideration when analyzing Si metal-oxide-semiconductor field-effect transistors (MOSFETs). Scattering reduces the mobility of the electrons and degrades the device performance. 250-nm and 50-nm bulk MOSFETs were simulated with varying device parameters and mesh sizes in order to compare the effects of surface-roughness scattering in multiple devices. The simulation framework includes the ensemble Monte Carlo method used to solve the Boltzmann transport equation coupled with a successive over-relaxation method used to solve the two-dimensional Poisson's equation. Four methods for simulating the surface-roughness scattering of electrons were implemented on both devices and compared: the constant specularity parameter, the momentum-dependent specularity parameter, and the real-space-roughness method with both uniform and varying electric fields. The specularity parameter is the probability of an electron scattering speculariy from a rough surface. It can be chosen as a constant, characterizing partially diffuse scattering of all electrons from the surface the same way, or it can be momentum dependent, where the size of rms roughness and the normal component of the electron wave number determine the probability of electron-momentum randomization. The real-space rough surface method uses the rms roughness height and correlation length of an actual MOSFET to simulate a rough interface. Due to their charge, electrons scatter from the electric field and not directly from the surface. If the electric field is kept uniform, the electrons do not perceive the roughness and scatter as if from a at surface. However, if the field is allowed to vary, the electrons scatter from the varying electric field as they would in a MOSFET. These methods were implemented for both the 50-nm and 250-nm MOSFETs, and using the rms roughness heights and correlation lengths for real devices. The current-voltage and mobility-electric field curves were plotted for each method on the two devices and compared. The conclusion is that the specularity-parameter methods are valuable as simple models for relatively smooth interfaces. However, they have limitations, as they cannot accurately describe the drastic reduction in the current and the electron mobility that occur in MOSFETs with very rough Si-SiO 2 interfaces.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

The Corrected Distortion model for Lagrangian spray simulation of transcritical fuel injection

In this work, we present a detailed implementation and validation of the droplet modeling framework proposed by Dahms and Oefelein (2016) into the engine commercial CFD software CONVERGE using the User Defined Function (UDF) interface. The model accounts for the nonlinear deformation and oscillation experienced by liquid spray droplet injected into high pressure and temperature. Lagrangian spray simulations of Engine Combustion Network (ECN) Spray A are performed. Model validation against standard experimental measurements of liquid velocity, vapor mixture fraction is conducted. To perform more rigorous model validation, new experimental measurements based on Diffused Back Illumination (DBI) are introduced. The new measurements are processed for Projected Liquid Volume (PLV), which offers as close as possible one-to-one model validation for liquid penetration while offering new insights into the spray physics. Comparison with a One-D model based on adiabatic mixing theory by Siebers (1999) and Desantes et al. (2007) are also conducted. Through these model validation exercises, it is shown that the new framework improves liquid-phase penetration predictions, following a tendency for enhanced evaporation, compared to the standard approach for both Reynolds Average Navier Stokes (RANS) and Large Eddy Simulation (LES). Additionally, at the liquid length, maximum mixture fraction values predicted by the new approach are in good agreement those of an adiabatic mixing model. Qualitative analysis of the spray behaviors during the early stage of the injection process reveals that the proposed framework predicts significant increase in droplet evaporation rate with lower drop drag compared to the current standard approach.

42 ENGINEERING↗
DOE OSTI2017

A facile microwave-hydrothermal method to fabricate B doped ZnWO{sub 4} nanorods with high crystalline and highly efficient photocatalytic activity

Highlights: • High-crystallized B/ZnWO{sub 4} nanorods were fabricated via a fast microwave -hydrothermal method. • B doping effectively decreases particle size and increase in specific surface area. • The seperation of photogenerated e{sup −} and h{sup +} was largely promoted by B doping. • B/ZnWO{sub 4} exhibit super photocatalytic activity in degradation organic dyes. - Abstract: A series length of 50∼200 nm B doped ZnWO{sub 4} nanorods with high crystallinity were fabricated via a fast microwave-hydrothermal method. The effects of B doping on the physical properties of ZnWO{sub 4} nanorods were intensively characterized by N{sub 2} physical adsorption, XRD, TEM, FT-IR, XPS, ultraviolet-visible diffuse reflection spectrum (UV–vis DRS), photolunminescence spectrum (PL), transient photocurrent response (TPR). The results indicated that the doped B could replace the lattice tungsten ion in ZnWO{sub 4} crystals, which caused the lattice spacing contraction, particle size decrease, specific surface area increase. More importantly, the separation of the photogenerated electrons and holes in ZnWO{sub 4} was significantly enhanced by B doping. With doped optimum B concentration (2.42 wt%), B/ZnWO{sub 4} displayed super photocatalytic performance in dyes decomposition. The degradation rate constant (0.065 h{sup −1}) of Rhodamine B over B (2.42 wt%)/ZnWO{sub 4} is 4 times of that over ZnWO{sub 4} (0.016 h{sup −1}).

36 MATERIALS SCIENCE↗
DOE OSTI2014

Investigating the effect of compression on solute transport through degrading municipal solid waste

Highlights: • The influence of compression on MSW flushing was evaluated using 13 tracer tests. • Compression has little effect on solute diffusion times in MSW. • Lithium tracer was conservative in non-degrading waste but not in degrading waste. • Bromide tracer was conservative, but deuterium was not. - Abstract: The effect of applied compression on the nature of liquid flow and hence the movement of contaminants within municipal solid waste was examined by means of thirteen tracer tests conducted on five separate waste samples. The conservative nature of bromide, lithium and deuterium tracers was evaluated and linked to the presence of degradation in the sample. Lithium and deuterium tracers were non-conservative in the presence of degradation, whereas the bromide remained effectively conservative under all conditions. Solute diffusion times into and out of less mobile blocks of waste were compared for each test under the assumption of dominantly dual-porosity flow. Despite the fact that hydraulic conductivity changed strongly with applied stress, the block diffusion times were found to be much less sensitive to compression. A simple conceptual model, whereby flow is dominated by sub-parallel low permeability obstructions which define predominantly horizontally aligned less mobile zones, is able to explain this result. Compression tends to narrow the gap between the obstructions, but not significantly alter the horizontal length scale. Irrespective of knowledge of the true flow pattern, these results show that simple models of solute flushing from landfill which do not include depth dependent changes in solute transport parameters are justified.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Tunable Growth of Layered Double Hydroxide Nanosheets through Hydrothermal Conversion of Atomic Layer Deposition Seed Layers

To enable the design and manufacturing of hierarchical nanomaterial architectures, there is a need for synthesis and processing methods that can enable tunable geometric control at the nanoscale while maintaining conformality on complex 3-D templates. Here, in this study, we explore the programmable control of vertically oriented Zn-Al layered double hydroxide (LDH) nanosheet arrays using atomic layer deposition (ALD) to deposit a seed layer of Al 2 O 3 , which is subsequently consumed and converted into the LDH phase under hydrothermal growth conditions. We demonstrate tunable control over the spacing and length of the nanosheets by varying the thickness of the initial ALD seed layer with subnanometer precision. This can be viewed as a nanoscale titration reaction, where Al acts as the limiting reagent during the hydrothermal synthesis of the nanosheets. Elemental mapping demonstrates the dynamic evolution of the resulting morphology, which is driven by surface diffusion and nucleation processes. The conformal nature of ALD allows for hierarchical growth of nanosheets on the surface of a variety of nonplanar substrate geometries, including microposts, paper fibers, and porous ceramic supports. This illustrates the power of ALD to enable bottom-up growth of 3-D nanoarchitectures with tunable geometries by controlling nucleation and growth in subsequent solution reactions.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Structure and Electronic Properties of Interface-Confined Oxide Nanostructures

The controlled fabrication of nanostructures has often made use of a substrate template to mediate and control the growth kinetics. Electronic substrate-mediated interactions have been demonstrated to guide the assembly of organic molecules or the nucleation of metal atoms but usually at cryogenic temperatures, where the diffusion has been limited. Combining STM, STS, and DFT studies, we report that the strong electronic interaction between transition metals and oxides could indeed govern the growth of low-dimensional oxide nanostructures. As a demonstration, a series of FeO triangles, which are of the same structure and electronic properties but with different sizes (side length >3 nm), are synthesized on Pt(111). The strong interfacial interaction confines the growth of FeO nanostructures, leading to a discrete size distribution and a uniform step structure. Given the same interfacial configuration, as-grown FeO nanostructures not only expose identical edge/surface structure but also exhibit the same electronic properties, as manifested by the local density of states and local work functions. We expect the interfacial confinement effect can be generally applied to control the growth of oxide nanostructures on transition metal surfaces. These oxide nanostructures of the same structure and electronic properties are excellent models for studies of nanoscale effects and applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2015

A VERY DEEP CHANDRA OBSERVATION OF A1795: THE COLD FRONT AND COOLING WAKE

We present a new analysis of very deep Chandra observations of the galaxy cluster A1795. Utilizing nearly 750 ks of net ACIS imaging, we are able to resolve the thermodynamic structure of the intracluster medium (ICM) on length scales of ∼1 kpc near the cool core. We find several previously unresolved structures, including a high pressure feature to the north of the Brightest Cluster Galaxy (BCG) that appears to arise from the bulk motion of A1795's cool core. To the south of the cool core, we find low temperature (∼3 keV), diffuse ICM gas extending for distances of ∼50 kpc spatially coincident with previously identified filaments of Hα emission. Gas at similar temperatures is also detected in adjacent regions without any Hα emission. The X-ray gas coincident with the Hα filament has been measured to be cooling spectroscopically at a rate of ∼1 M{sub ⊙} yr{sup −1}, consistent with measurements of the star formation rate in this region as inferred from ultraviolet (UV) observations, suggesting that the star formation in this filament as inferred by its Hα and UV emission can trace its origin to the rapid cooling of dense, X-ray emitting gas. The Hα filament is not a unique site of cooler ICM, however, as ICM at similar temperatures and even higher metallicities not cospatial with Hα emission is observed just to the west of the Hα filament, suggesting that it may have been uplifted by A1795's central active galaxy. Further simulations of cool core sloshing and active galactic nucleus feedback operating in concert with one another will be necessary to understand how such a dynamic cool core region may have originated and why the Hα emission is so localized with respect to the cool X-ray gas.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1973

Thermal expansion method for lining tantalum alloy tubing with tungsten

A differential-thermal expansion method was developed to line T-111 (tantalum - 8 percent tungsten - 2 percent hafnium) tubing with a tungsten diffusion barrier as part of a fuel element fabrication study for a space power nuclear reactor concept. This method uses a steel mandrel, which has a larger thermal expansion than T-111, to force the tungsten against the inside of the T-111 tube. Variables investigated include lining temperature, initial assembly gas size, and tube length. Linear integrity increased with increasing lining temperature and decreasing gap size. The method should have more general applicability where cylinders must be lined with a thin layer of a second material.

Watson, G. K.↗
DOE OSTI2019

Examination of Dendritic Growth During Solidification of Ternary Alloys via a Novel Quantitative 3D Cellular Automaton Model

A three-dimensional (3D) quantitative cellular automaton (CA) model was developed to simulate dendritic growth during solidification processing of ternary alloys. A detailed method was proposed to solve solute diffusion and calculate the solid fraction for ternary alloys during solidification. The present model has been shown to accurately predict dendrite morphologies and solute distributions of both single equiaxed dendrite and columnar dendrites during solidification. The model was also used to study the influence of the concentration of a third component (Mg in the Al-Si-Mg system) on dendritic growth. With increasing Mg concentration, the steady-state dendrite tip growth velocity was shown to decrease, resulting in a shorter primary dendrite length. The 3D CA simulation results agree well with the prediction of the LGK theoretical model. Multi-columnar dendrite growth was simulated with different cooling rates. Primary and secondary dendrite morphology was shown to have little variation at low cooling rates (1.0 to 2.0 K/s) and a constant undercooling. The average secondary dendrite arm spacing was shown to decrease with the increase of cooling rate within this range. The 3D CA simulation results are in good agreement with the experimental directional solidification experiments of a commercial A356 (Al-7 wt pct Si-0.3 wt pct Mg).

36 MATERIALS SCIENCE↗
DOE OSTI2014

Reduced model prediction of electron temperature profiles in microtearing-dominated National Spherical Torus eXperiment plasmas

A representative H-mode discharge from the National Spherical Torus eXperiment is studied in detail to utilize it as a basis for a time-evolving prediction of the electron temperature profile using an appropriate reduced transport model. The time evolution of characteristic plasma variables such as β{sub e}, ν{sub e}{sup ∗}, the MHD α parameter, and the gradient scale lengths of T{sub e}, T{sub i}, and n{sub e} were examined as a prelude to performing linear gyrokinetic calculations to determine the fastest growing micro instability at various times and locations throughout the discharge. The inferences from the parameter evolutions and the linear stability calculations were consistent. Early in the discharge, when β{sub e} and ν{sub e}{sup ∗} were relatively low, ballooning parity modes were dominant. As time progressed and both β{sub e} and ν{sub e}{sup ∗} increased, microtearing became the dominant low-k{sub θ} mode, especially in the outer half of the plasma. There are instances in time and radius, however, where other modes, at higher-k{sub θ}, may, in addition to microtearing, be important for driving electron transport. Given these results, the Rebut-Lallia-Watkins (RLW) electron thermal diffusivity model, which is based on microtearing-induced transport, was used to predict the time-evolving electron temperature across most of the profile. The results indicate that RLW does a good job of predicting T{sub e} for times and locations where microtearing was determined to be important, but not as well when microtearing was predicted to be stable or subdominant.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2017

Proton imaging of stochastic magnetic fields

Recent laser-plasma experiments report the existence of dynamically significant magnetic fields, whose statistical characterization is essential for a complete understanding of the physical processes these experiments are attempting to investigate. In this paper, we show how a proton-imaging diagnostic can be used to determine a range of relevant magnetic-field statistics, including the magnetic-energy spectrum. To achieve this goal, we explore the properties of an analytic relation between a stochastic magnetic field and the image-flux distribution created upon imaging that field. This ‘Kugland image-flux relation’ was previously derived under simplifying assumptions typically valid in actual proton-imaging set-ups. We conclude that, as with regular electromagnetic fields, features of the beam’s final image-flux distribution often display a universal character determined by a single, field-scale dependent parameter – the contrast parameter $\unicode[STIX]{x1D707}\equiv d_{s}/{\mathcal{M}}l_{B}$ – which quantifies the relative size of the correlation length $l_{B}$ of the stochastic field, proton displacements $d_{s}$ due to magnetic deflections and the image magnification ${\mathcal{M}}$ . For stochastic magnetic fields, we establish the existence of four contrast regimes, under which proton-flux images relate to their parent fields in a qualitatively distinct manner. These are linear, nonlinear injective, caustic and diffusive. The diffusive regime is newly identified and characterized. The nonlinear injective regime is distinguished from the caustic regime in manifesting nonlinear behaviour, but as in the linear regime, the path-integrated magnetic field experienced by the beam can be extracted uniquely. Thus, in the linear and nonlinear injective regimes we show that the magnetic-energy spectrum can be obtained under a further statistical assumption of isotropy. This is not the case in the caustic or diffusive regimes. We discuss complications to the contrast-regime characterization arising for inhomogeneous, multi-scale stochastic fields, which can encompass many contrast regimes, as well as limitations currently placed by experimental capabilities on one’s ability to extract magnetic-field statistics. Furthermore, the results presented in this paper are of consequence in providing a comprehensive description of proton images of stochastic magnetic fields, with applications for improved analysis of proton-flux images.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Smooth Modified Surfaces of Silicon for the Study of Ionic Liquid Interfaces by Neutron Reflectometry

Silicon surfaces with termination of hydrogen (H–Si), quartz, native silicon (native-Si), and chemically deposited (Au–Si) cd and sputtered gold (Au–Si) s were fabricated with roughness less than 6 Å to study the solid–liquid interface of the ionic liquid (IL) methyltrioctylammonium bis(trifluoromethylsulfonyl)imide, [N 1888 ][TFSI], by neutron reflectometry (NR). The modifications made to the silicon surface were to obtain a native positive or negative charge similar to a charged surface in electrochemical systems. The differences in scattering length density (SLD) based on mass density and composition of IL were examined. Perpendicular to the substrate surface, a distinct transition between the first ion layer and the bulk liquid is resolved out of the reflectivity data for the gold surfaces and in particular the chemically deposited Au–Si. Other interfaces are best described by a diffuse transition between regions of different SLDs. The diffuse transitions between SLDs observed here suggest that the interfacial structure of IL, while ordered, is best described by a continuous variation in composition as opposed to distinct layers of ions.

25 ENERGY STORAGE↗
DOE OSTI2024

Complexes of tubulin oligomers and tau form a viscoelastic intervening network cross-bridging microtubules into bundles

Abstract The axon-initial-segment (AIS) of mature neurons contains microtubule (MT) fascicles (linear bundles) implicated as retrograde diffusion barriers in the retention of MT-associated protein (MAP) tau inside axons. Tau dysfunction and leakage outside of the axon is associated with neurodegeneration. We report on the structure of steady-state MT bundles in varying concentrations of Mg 2+ or Ca 2+ divalent cations in mixtures containing αβ-tubulin, full-length tau, and GTP at 37 °C in a physiological buffer. A concentration-time kinetic phase diagram generated by synchrotron SAXS reveals a wide-spacing MT bundle phase (B ws ), a transient intermediate MT bundle phase (B int ), and a tubulin ring phase. SAXS with TEM of plastic-embedded samples provides evidence of a viscoelastic intervening network (IN) of complexes of tubulin oligomers and tau stabilizing MT bundles. In this model, αβ-tubulin oligomers in the IN are crosslinked by tau’s MT binding repeats, which also link αβ-tubulin oligomers to αβ-tubulin within the MT lattice. The model challenges whether the cross-bridging of MTs is attributed entirely to MAPs. Tubulin-tau complexes in the IN or bound to isolated MTs are potential sites for enzymatic modification of tau, promoting nucleation and growth of tau fibrils in tauopathies.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2019

On the mechanisms of stress relaxation and intensification at the lithium/solid-state electrolyte interface

Under electrochemical cycling, stress intensification and relaxation within small volumes at the lithium/solid-state electrolyte (SSE) interface are thought to be critical factors contributing to mechanical failure of the SSE and subsequent short-circuiting of the device. Nanoindentation has been used to examine the diffusion-limited pressure lithium can support in the absence of active dislocation sources at high homologous temperatures. Based on the underlying physics of this deformation mechanism, a simple perturbation model coupling local current density, elastic stress, and diffusional creep relaxation is introduced. Combining this analysis with the indentation results, it is possible to describe a defect length scale which is too large for effective diffusional creep relaxation, but too small for efficient dislocation multiplication. In this instance, the properties of the SSE may become critical, and relevant indentation results of the SSE are described. Lastly, the final outcome of the proposed analysis is a newly developed deformation mechanism map.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Microbiological-enhanced mixing across scales during in-situ bioreduction of metals and radionuclides at Department of Energy Sites

Bioreduction is being actively investigated as an effective strategy for subsurface remediation and long-term management of DOE sites contaminated by metals and radionuclides (i.e. U(VI)). These strategies require manipulation of the subsurface, usually through injection of chemicals (e.g., electron donor) which mix at varying scales with the contaminant to stimulate metal reducing bacteria. There is evidence from DOE field experiments suggesting that mixing limitations of substrates at all scales may affect biological growth and activity for U(VI) reduction. Although current conceptual models hold that biomass growth and reduction activity is limited by physical mixing processes, a growing body of literature suggests that reaction could be enhanced by cell-to-cell interaction occurring over length scales extending tens to thousands of microns. Our project investigated two potential mechanisms of enhanced electron transfer. The first is the formation of single- or multiple-species biofilms that transport electrons via direct electrical connection such as conductive pili (i.e. ‘nanowires’) through biofilms to where the electron acceptor is available. The second is through diffusion of electron carriers from syntrophic bacteria to dissimilatory metal reducing bacteria (DMRB). The specific objectives of this work are (i) to quantify the extent and rate that electrons are transported between microorganisms in physical mixing zones between an electron donor and electron acceptor (e.g. U(IV)), (ii) to quantify the extent that biomass growth and reaction are enhanced by interspecies electron transport, and (iii) to integrate mixing across scales (e.g., microscopic scale of electron transfer and macroscopic scale of diffusion) in an integrated numerical model to quantify these mechanisms on overall U(VI) reduction rates. We tested these hypotheses with five tasks that integrate microbiological experiments, unique micro-fluidics experiments, flow cell experiments, and multi-scale numerical models. Continuous fed-batch reactors were used to derive kinetic parameters for DMRB, and to develop an enrichment culture for elucidation of syntrophic relationships in a complex microbial community. Pore and continuum scale experiments using microfluidic and bench top flow cells were used to evaluate the impact of cell-to-cell and microbial interactions on reaction enhancement in mixing-limited bioactive zones, and the mechanisms of this interaction. Some of the microfluidic experiments were used to develop and test models that considers direct cell-to-cell interactions during metal reduction. Pore scale models were incorporated into a multi-scale hybrid modeling framework that combines pore scale modeling at the reaction interface with continuum scale modeling. New computational frameworks for combining continuum and pore-scale models were also developed

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1994

Electron injection and acceleration at nonlinear shocks: Results of numerical simulations

We present results of numerical simulations of electron injection and acceleration at nonlinear high Mach number shocks. The electrons are assumed to be heated at the thermal subshock to an energy E(sub inj), which is treated as a free parameter, above which they are injected by self-generated whistlers to momentum m(sub p) x V(sub A). This injection mechanism requires Mach numbers greater than (43/(beta(sub -)))(((k T(sub e))/(E(sub inj)))(exp 1/2)), where T(sub e) and beta (sub -) are the upstream electron temperature and plasma beta parameter. Above m(sub p) x V(sub A) electrons are trapped in the shock by Alfven waves. In the proton precursor region the Alfven waves are assumed to be generated by protons accelerated at the shock, and have nonlinear intensities. Below GeV, however, electrons of a given rigidity propagate faster than protons with a similar rigidity and therefore diffuse to regions ahead of the proton precursor. In those regions the Alfven waves are generated by the electrons themselves. The diffusion coefficient appears to increase with decreasing acceleration efficiency. As a result, the number of electrons accelerated to energies GeV and above and, hence, the electron to proton ratio, depend only weakly on the extent of electron heating at the subshock. The negative feedback also renders the electron spectra insensitive to shock compression ratio and smoothing length scale. The estimated e/p ratio at GeV is between approximately 1%-10%.

Levinson, Amir↗
NASA NTRSDate not supplied

Influence of Thermophysical Property Variability on Thermal Predictions of Ti-6Al-4V

The additive manufacturing (AM) industry has experienced rapid growth in recent decades as industrial interest in the process has grown. Because of this, there are many groups interested in simulations of the AM process. However, the influence of thermophysical property variability on the melt pool geometry during processing of various AM alloys is unclear. The goal of my work at NASA Langley Research Center (LaRC) was to characterize this influence on Ti-6Al-4V during AM processing alongside developing a tool to enable equivalent studies on other AM materials. To facilitate this process, a database tool was developed to contain and organize thermophysical data previously reported by primary sources. The specific thermophysical properties of interest for this study were density, specific heat capacity, and conductivity. Thermal diffusivity was calculated using the other three properties. This data was then fit with a Gaussian distribution and then randomly sampled from using Monte Carlo random value sampling. Using the Rosenthal equation, this sample data was used to simulate the temperature field during additive manufacturing and extract the melt pool geometry. Specifically, the melt pool’s length, width, and depth. This process was repeated an arbitrary number of times, with the default being 1000. Once this information was obtained, histograms were made showing the distributions of the sizes of the melt pool’s length, width, and depth. Representative statistical metrics of the distributions were calculated (mean, standard deviation, and coefficient of variance). This work found that at the simulated processing values, the melt pool’s width and depth had a 5.7% variation while the length had a 3.2% variation. Additionally, a tool was constructed to graph a thermal color map representation of the melt pool for specific, arbitrary values of density, specific heat, and conductivity. This tool allowed for more efficient plotting of individual queries of the thermophysical properties. The results that were observed in the research were that values reported in literature vary and this variance can have a significant impact on the simulation. Predictions of the melt pool’s dimensions show that length has a standard deviation of approximately 6 μm, width has a standard deviation of approximately 5 μm, and depth can vary by approximately 3 μm. Considering the mean sizes of length, width, and depth are 185 μm, 88 μm, and 44 μm respectively, such a deviation is significant. This shows that depth, for example, could be more than 10% larger or smaller than expected. This demonstrates that variability in the reported thermophysical properties are not negligible and should be expected to have an influence on the results of the laser powder bed fusion additive manufacturing process. When simulating this process in the future, measures should be taken to account for this discrepancy and the uncertainty involved

Justin Martin↗